Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Chemistry · Chapter 51Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Laundry powder detergent

    sodium carbonate, metasilicate, alkylbenzene sulfonate, and alcohol ethoxylate, the 0.04 to 0.09 percent solution, dust and skin, moisture and caking, and handling and storage

    In a hospital laundry, caked powder detergent is broken up with bare, sweaty hands; the skin between the worker’s fingers only turns red and sore several hours later. This chapter covers laundry powder detergent from the product side, according to the manufacturer’s safety data sheet for one product of this class: sodium carbonate at 30 to 60 percent, disodium metasilicate, sodium dodecylbenzene sulfonate, alcohol ethoxylate, and silica, a pH of 11 to 12 for the 10 percent solution, and the class skin corrosion category 1B. It covers where the basic nature of the powder comes from, what the use solution of 0.04 to 0.09 percent means and why that figure is not yet a dose, dust and powder on damp skin, moisture and caking, incompatible materials, personal protective equipment, first aid, and handling and storage. Wash programs, doses, and dispenser settings are not given. Large spills and treating a casualty are stated as work for other parties.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    In a hospital laundry, powder detergent was kept in a plastic drum with no lid beside the washing machine, in a room that was always damp with steam. One morning the powder in the drum had caked hard. A worker broke up the lumps by hand without gloves, then scooped the powder into the machine. Their palms were sweating, and powder stuck between their fingers. While working they felt nothing. Toward midday the skin between their fingers turned red and sore, and the colleague beside them sneezed every time that drum was stirred.

    That powder is different from household detergent. According to the manufacturer’s safety data sheet for one product of this class, that laundry powder detergent falls in the class skin corrosion category 1B, and its 10 percent solution has a pH of 11 to 12. Dry powder that meets sweat becomes a concentrated solution on the skin, and an injury from a basic substance may be painless at first. Workers need to know what is in that powder, when dry powder becomes a hazard, and why the lid of the container also decides the safety of the person measuring it out.

    Scope

    This chapter covers one class of product, namely basic powder detergent for commercial laundries: its contents and pH, where its basic nature comes from, what the use solution of 0.04 to 0.09 percent on the data sheet means, dust and skin contact, moisture and caking, incompatible materials, personal protective equipment, first aid, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of this class. Other products may differ, so what applies is the label and the safety data sheet of the product in use.

    This chapter is study material, not a work instruction. Wash programs, the dose per kilogram of linen, and dispenser settings are not given; all of them come from the product label, the chemical supplier, and the laundry procedure. How alkalis, surfactants, and chelating agents clean is in Chapter 6 · Laundry on cleaning chemistry. pH throughout the cycle is in Chapter 9 · Laundry on pH and chemical measurement throughout the cycle, program layout is in Chapter 11 · Laundry on wash program architecture, and dosing is in Chapter 12 · Laundry on sorting, program design, and dose scaling. Dispensers are covered in Chapter 3 · Chemical Dispensing on laundry dispenser controllers.

    How to check a data sheet is in Chapter 26 on reading safety data sheets for cleaning products, chemical burns are in Chapter 41 · Biology & Microbiology on skin and chemicals, and laundry safety is in Chapter 21 · Laundry on laundry occupational safety and health (K3). Other laundry products are covered in Chapter 49 on laundry alkali builders, Chapter 50 on liquid laundry detergents and enzyme detergents, Chapter 53 on chlorine bleaches for laundry, Chapter 54 on laundry neutralizers, and Chapter 55 on acid laundry softeners.

    Work outside the authority of laundry staff and building technicians: setting the dose and adjusting the dispenser, handling large spills or powder mixed with an acid product, and giving treatment other than first aid. The dose and the dispenser belong to the laundry supervisor together with the chemical supplier, large spills belong to trained personnel or the emergency response team, and casualties are handled by a doctor or the emergency services.

    What the product contains according to the data sheet

    According to the manufacturer’s safety data sheet for one product of this class, the detergent is a powder that dissolves in water, made for industrial and professional use, with a relative density of 0.64 to 0.74. The classification of the product as sold is acute oral toxicity category 4, skin corrosion category 1B, and serious eye damage category 1. That data sheet was issued on February 22, 2024 and is valid until February 21, 2029.

    IngredientCAS numberConcentration (percent)Class
    Sodium carbonate497-19-830 to 60basic salt
    Disodium metasilicate6834-92-010 to 30basic salt
    Sodium dodecylbenzene sulfonate25155-30-010 to 30anionic surfactant
    Alcohols, C12 to C16, ethoxylated68551-12-25 to 10nonionic surfactant
    Precipitated silica112926-00-81 to 5amorphous silica

    The class column is this chapter’s own note; the data sheet contains only the names, the CAS numbers, and the concentrations. Sodium dodecylbenzene sulfonate is one member of the alkylbenzene sulfonate family. The lower ends of the five ranges add up to 56 percent and their upper ends to 135 percent (Example 1), so the concentrations cannot all sit at their upper ends. This chapter reads those percentages as percent by mass.

    Sodium carbonate and metasilicate: where the basic nature comes from

    In 1939 the United States National Bureau of Standards described soda ash, that is, sodium carbonate with no water of crystallization, as a water softener, a soap builder, and a detergent aid in laundering for work that calls for a moderately strong alkaline material. Sodium metasilicate, according to the same document, is widely used in bottle washing, in dishwashing compounds, and in industrial metal cleaning because it dissolves rapidly and is alkaline. Those two salts make up 40 to 90 percent of the powder, so this powder is essentially a mixture of basic salts with surfactants.

    Carbonates are moderately strong bases. Their solutions are basic because the carbonate ion accepts a hydrogen ion from water and leaves a hydroxide ion behind:

    CO32−+H2O⇌HCO3−+OH−\text{CO}_3^{2-} + \text{H}_2\text{O} \rightleftharpoons \text{HCO}_3^- + \text{OH}^-

    For a carbonate solution of concentration CC mol/L, the hydroxide ion concentration xx satisfies

    Kb=x2C−x,Kb=KwKa2,pH=14.00+log⁡xK_b = \frac{x^2}{C - x}, \qquad K_b = \frac{K_w}{K_{a2}}, \qquad \text{pH} = 14.00 + \log x

    where Kw=1.0×10−14K_w = 1.0 \times 10^{-14} and Ka2=4.7×10−11K_{a2} = 4.7 \times 10^{-11}, the second ionization constant of carbonic acid, so that Kb=2.13×10−4K_b = 2.13 \times 10^{-4}. This formula holds at 25 °C, treats the solution as ideal, and counts only the carbonate. The metasilicate, the surfactants, water hardness, and the soil on the linen are not counted. The data sheet gives a pH of 11 to 12 for the 10 percent solution. The calculation from the carbonate alone lands at the upper end of that range (Example 4).

    Two surfactants and silica

    Synthetic detergents contain a nonpolar hydrocarbon chain and an ionic group such as a sulfate or a sulfonate. The hydrocarbon end is attracted to oil and dirt, the ionic end is attracted to water, so the dirt becomes suspended and is carried away by the rinse. Unlike soap, detergents form soluble products with calcium and magnesium in hard water. Sodium dodecylbenzene sulfonate belongs to that sulfonate group. The United States Environmental Protection Agency (EPA) notes that the majority of alkylbenzene sulfonates are used as household laundry and dish detergents, and that this group is irritating to the eyes and skin but does not cause skin sensitization.

    The ethoxylated alcohol is a nonionic surfactant, the class covered in Chapter 21 on surfactants, colloids, and emulsions. The function of the precipitated silica in the powder is not written on the data sheet. The annex to Permenaker (Minister of Manpower Regulation) 5/2018 lists precipitated silica with the same CAS number in the amorphous silica group, with a threshold limit value of 10 mg/m³. As of November 2026 that regulation is listed as in force on JDIH Kemnaker, the ministry’s legal documentation site. Amorphous silica is different from crystalline silica, which is covered in Chapter 18 · Safety on asbestos and hazardous materials during the renovation of old buildings.

    The 0.04 to 0.09 percent solution: what that figure means

    The data sheet has two columns: the product as sold, that is, the powder in the container, and the use solution. The use dilution written there is 0.04 to 0.09 percent, and at that concentration the solution is not classified as a hazardous substance or mixture. What the two columns mean is covered in Chapter 26.

    A concentration in percent is converted to grams per liter with

    c=10×pc = 10 \times p

    where cc is the concentration in g/L and pp is the concentration in percent by mass. This formula assumes that one liter of solution has a mass of 1,000 g, which is reasonable for a solution this dilute. A 0.04 percent solution contains 0.4 g of powder per liter, and a 0.09 percent solution contains 0.9 g per liter (Example 3).

    That figure is the concentration of the use solution according to the manufacturer, and it is not yet a dose for a program. The amount of powder per kilogram of linen depends on the soil level, the water hardness, and the program stage, and is set by the laundry supervisor together with the supplier according to the product label and Chapter 12 · Laundry. The words “not classified” do not mean neutral either. From its carbonate alone, that use solution is estimated to have a pH of about 10.6 to 11.0 (Example 5), so hands that are repeatedly wet with wash water are still exposed to a basic solution.

    Dust and skin

    People meet the concentrated powder when the container is opened, when the powder is scooped, and when the powder is poured into the machine or the dispenser. UKHSA, the UK Health Security Agency, in its guidance for sodium hydroxide writes about basic substances in general: symptoms are more likely to occur following direct contact with solid or liquid corrosive materials, and alkalis damage tissue by saponifying fats and solubilizing proteins and collagen. Alkali injuries to the skin may be painless at first, so that treatment is delayed, and may progress over several hours. Sodium hydroxide is a stronger base than the salts in this powder, but the data sheet for this powder also gives the class skin corrosion.

    Dry powder only acts as a base once it meets water, and skin provides it. Sweat, hands that have just been washed, gloves that are wet inside, and damp sleeves dissolve the powder that sticks to them into a solution that may be far more concentrated than the 10 percent solution whose pH is 11 to 12. In the opening case, the sequence of events fits that property: powder, sweat, no pain, then soreness several hours later.

    For the eyes, UKHSA writes that alkaline solutions may penetrate and damage all layers of the eye, so they must be treated as an eye emergency. Powder grains that get into the eye meet the tear fluid, so eye protection is worn from the moment the container is opened.

    Dust rises when powder is poured from a height, when a container is emptied, and when lumps are broken up. HSE, the British occupational safety authority, in its guidance for the textile industry notes that soda ash is among the substances that can cause skin irritation, itchy and stuffy noses, sneezing, and sore eyes. In the British hazardous substances regulations, dust of any kind counts as a substance hazardous to health when its concentration in air reaches 10 mg/m³ of inhalable dust as an 8-hour average. The amount of powder that equals that figure in a small room is very small (Example 6).

    For hospitality workers HSE gives one short rule: powders are always dispensed with a scoop, never by hand.

    Moisture and caking

    Water of crystallization is water that is bound inside the crystals of a salt in a fixed ratio. The National Bureau of Standards wrote that sal soda is sodium carbonate combined with 10 molecules of water of crystallization and is more than 60 percent water by mass, that it writes the formula of sodium metasilicate with 5 molecules of water, and that a high content of combined water in a mixture of alkaline powders may cause caking and prevent free flowing. The two main salts of this powder can bind water, and a laundry room supplies water vapor all day long.

    Caking changes three things. First, measuring. A measuring scoop measures volume, whereas a dose is calculated by mass; the density of caked powder is no longer the same as that of free-flowing powder (Example 2). Second, dissolving. Lumps may take longer to dissolve than fine powder, and a lump that has not yet dissolved among the linen means a concentrated solution in one spot. Third, how people behave. Lumps invite people to break them up by hand or to hit the container, and both produce dust as well as skin contact.

    The data sheet gives no figure for the humidity that is still safe for this powder. HSE asks for scoops and buckets for chemicals to be always clean and dry, and for substances that are sensitive to water it asks for container lids to be kept on at all times. Powder that has caked hard is not broken up by hand and is not forced into a powder dispenser; the supervisor asks the supplier whether that powder is still fit for use. Storeroom humidity control is covered in Chapter 25 · Fluids & Thermal on humidity control in storerooms and archive rooms.

    Personal protective equipment and first aid

    HSE guidance for cleaning substances in hospitality also applies in the laundry room:

    • The protective clothing provided is always worn when handling cleaning substances, especially concentrates.
    • Eye protection suitable for splash risks, for example goggles or a visor, is worn if there is any chance of splashing.
    • Rubber gloves are checked for holes, tears, and thin patches, and replaced if faulty.
    • Where tap water is not available for rinsing the eyes, at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers is provided.

    Gloves that powder has got into are replaced, because the powder inside sticks to damp skin. The glove material and the respiratory protection are read from the product’s data sheet and Chapter 5 · Safety on personal protective equipment.

    First aid follows the workplace procedure. HSE guidance for chemical injuries and UKHSA guidance for basic substances:

    1. Eyes. The eye is flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then the casualty is sent to hospital.
    2. Skin. Powder sticking to the skin is removed, then the skin is washed with copious amounts of water for at least 10 to 15 minutes, with attention to skin folds and fingernails. For chemical burns, HSE asks for the affected area to be flooded with water for 20 minutes, for contaminated clothing that is not stuck to the skin to be removed, and for the first aider to avoid being contaminated as well.
    3. Swallowed or inhaled. The casualty is moved away from the dust, and a doctor or the emergency services are contacted.

    All of that guidance uses water, not vinegar or any other acid. Skin that has been in contact with the powder is rinsed even if it does not hurt. The label or the product’s data sheet is taken to the doctor.

    Incompatible materials, handling, and storage

    The manufacturer’s safety data sheet for one product of this class gives a storage temperature of 0 to 45 °C and names acids as incompatible materials. Carbonates react with acids to form salts, carbon dioxide gas, and water. Acid poured onto this powder foams, and that foam can carry basic powder and acid out of the container. In a laundry, acid products may sit on the same shelf: neutralizers, which are covered in Chapter 54, and acid softeners in Chapter 55.

    The same HSE guidance gives rules for a chemical store: acids are kept separate from alkalis, incompatible substances are stored in segregated, marked places, and scoops and buckets are always clean and dry, because cross-contamination of incompatible substances may result in a violent reaction. A measuring scoop for one product is not used for another product.

    The National Bureau of Standards notes that for certain metals such as tin, aluminum, zinc, and copper, sodium metasilicate may damage the surface, so a less alkaline silicate is used. Measuring scoops and intermediate containers made of aluminum or zinc-coated metal are not used for this powder; compatibility with machine parts is read from the label and asked of the supplier.

    HSE guidance for storing cleaning substances: original labeled containers with lids, away from heat, sunlight, foodstuffs, and members of the public, not transferred into food or drink containers, and spills cleaned up immediately. Spilled powder is cleaned up according to the spill procedure, without raising dust and without pouring acid on it. Small spills are handled according to Chapter 6 · Safety on chemicals in technician work, and heavy containers are moved according to Chapter 9 · Safety on lifting and moving loads with equipment.

    Worked example

    The figures in the examples below are practice figures, unless their origin is stated. The molar mass of sodium carbonate is 105.99 g/mol, and a relative density of 0.69 is used as the midpoint of the range on the data sheet.

    Example 1: what each kilogram of powder contains. One kilogram of powder contains sodium carbonate at 0.30×1,000=3000.30 \times 1{,}000 = 300 g to 0.60×1,000=6000.60 \times 1{,}000 = 600 g, metasilicate and dodecylbenzene sulfonate at 0.10×1,000=1000.10 \times 1{,}000 = 100 g to 0.30×1,000=3000.30 \times 1{,}000 = 300 g each, ethoxylated alcohol at 50 to 100 g, and silica at 10 to 50 g. The lower ends add up to 30+10+10+5+1=5630 + 10 + 10 + 5 + 1 = 56 percent and the upper ends to 60+30+30+10+5=13560 + 30 + 30 + 10 + 5 = 135 percent. The two basic salts add up to 30+10=4030 + 10 = 40 percent to 60+30=9060 + 30 = 90 percent.

    Example 2: a measuring scoop measures volume. A 250 mL measuring scoop holds 250×0.69=172.5250 \times 0.69 = 172.5 g of powder at the midpoint density. At the ends of the range, it holds 250×0.64=160250 \times 0.64 = 160 g to 250×0.74=185250 \times 0.74 = 185 g, a difference of 185−160=25185 - 160 = 25 g for the same scoop. A 25 kg container holds 25/0.69=36.225/0.69 = 36.2 L of powder. That range applies to free-flowing powder; for caked powder, measuring with a scoop can no longer be relied on.

    Example 3: what 0.04 to 0.09 percent means. A 0.04 percent solution contains 10×0.04=0.410 \times 0.04 = 0.4 g/L and a 0.09 percent solution 10×0.09=0.910 \times 0.09 = 0.9 g/L. For 150 L of water in the machine, that is 150×0.4=60150 \times 0.4 = 60 g to 150×0.9=135150 \times 0.9 = 135 g of powder. This calculation only translates the use solution concentration on the data sheet into grams. The dose for a program is read from the label and set by the laundry supervisor.

    Example 4: whether the pH agrees with the carbonate content. A 10 percent solution contains 100 g of powder per liter, so its sodium carbonate is 30 to 60 g/L, that is, C=30/105.99=0.283C = 30/105.99 = 0.283 mol/L to C=60/105.99=0.566C = 60/105.99 = 0.566 mol/L. For the lowest concentration, x=(−Kb+Kb2+4KbC)/2=0.00766x = (-K_b + \sqrt{K_b^2 + 4K_bC})/2 = 0.00766 mol/L, so pH =14.00+log⁡0.00766=11.88= 14.00 + \log 0.00766 = 11.88. For the highest concentration, x=0.0109x = 0.0109 mol/L and pH =14.00+log⁡0.0109=12.04= 14.00 + \log 0.0109 = 12.04. The result of 11.88 to 12.04 lies at the upper end of the range of 11 to 12 on the data sheet.

    Example 5: the use solution is still basic. At 0.4 g/L and a carbonate content of 30 percent, the carbonate is 0.30×0.4=0.120.30 \times 0.4 = 0.12 g/L, so C=0.12/105.99=0.00113C = 0.12/105.99 = 0.00113 mol/L, x=0.000396x = 0.000396 mol/L, and pH =14.00+log⁡0.000396=10.60= 14.00 + \log 0.000396 = 10.60. At 0.9 g/L and a carbonate content of 60 percent, the carbonate is 0.60×0.9=0.540.60 \times 0.9 = 0.54 g/L, so C=0.54/105.99=0.00509C = 0.54/105.99 = 0.00509 mol/L, x=0.000940x = 0.000940 mol/L, and pH =14.00+log⁡0.000940=10.97= 14.00 + \log 0.000940 = 10.97. Compared with the 10 percent solution, the use solution is 100/0.9=111100/0.9 = 111 to 100/0.4=250100/0.4 = 250 times more dilute, yet its pH drops by only about one unit. These figures hold for pure water; hard water and soil change them.

    Example 6: dust in the measuring room. A chemical storeroom measuring 5 m by 4 m by 3 m has a volume of 5×4×3=605 \times 4 \times 3 = 60 m³. The figure 10 mg/m³ is equaled by 10×60=60010 \times 60 = 600 mg of dust, that is, 0.6 g of airborne powder. For the silica alone, at a content of 5 percent the figure 10 mg/m³ is equaled by 600/0.05=12,000600/0.05 = 12{,}000 mg, that is, 12 g of powder. Less than one gram of airborne powder already equals the general dust figure in that room, and this dust is basic.

    Stop conditions

    1. Powder or concentrated solution gets in the eyes: stop work and rinse immediately with water. The casualty is taken to hospital.
    2. Powder sticks to wet skin, or the skin turns red or sore even slightly: remove the powder and rinse with plenty of water. The casualty is examined by a doctor.
    3. A person swallows powder, or coughs and is short of breath after inhaling dust: move them away from the dust and call a doctor or the emergency services. Do not give vinegar or any other neutralizing substance.
    4. Eye protection or gloves are missing or damaged, or there is no eyewash near the place where powder is measured: do not open the container. The laundry supervisor provides the equipment first.
    5. The container has no label, powder has been transferred into a food or drink container, or the safety data sheet is missing or past its validity date: do not use it. The supervisor asks the supplier for clarification.
    6. The powder has caked hard or is wet: do not break it up by hand and do not put it into the dispenser. The supervisor asks the supplier whether it is fit for use.
    7. Powder meets an acid product, or the mixture foams or feels hot: stay away from the container and clear the area. The supervisor calls trained personnel or the building’s emergency response team.
    8. Dust is seen hanging in the air, or people in the room sneeze and cough while powder is being measured: stop pouring. The supervisor changes the measuring method or the ventilation before work continues.
    9. A spill is larger than the local spill kit can handle, or powder gets into a drain: close off that area. Trained personnel or the emergency response team deal with it.
    10. A worker is asked to decide the dose themselves or to change the dispenser setting: do not do it. The dose and the setting are set by the laundry supervisor together with the supplier.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    Laundry powder detergent is the same as household detergent, only in a bigger pack.

    Why is it wrong?

    The data sheet for the product of this class gives skin corrosion category 1B and a pH of 11 to 12 for the 10 percent solution. This product is made for professional use.

    Common misconception

    Dry powder does not injure skin.

    Why is it wrong?

    Sweat and water on the skin dissolve the powder into a concentrated solution. Alkali injuries may be painless at first and progress over several hours.

    Common misconception

    The figure 0.04 to 0.09 percent is enough to set the dose.

    Why is it wrong?

    That figure is the use solution concentration on the data sheet. The dose for each program is read from the label and set by the laundry supervisor together with the supplier.

    Common misconception

    The use solution is not classified as hazardous, so it is neutral.

    Why is it wrong?

    From its carbonate alone the pH of that solution is estimated at about 10.6 to 11.0. Hands that stay wet with wash water still need protection.

    Common misconception

    Lumps can simply be broken up by hand.

    Why is it wrong?

    Breaking up lumps produces dust and skin contact. Powder that has caked hard is referred to the supplier to ask whether it is fit for use.

    Common misconception

    Spilled powder is neutralized with an acid product.

    Why is it wrong?

    Carbonate and acid produce gas and foam that can carry both substances out. Spills are handled according to the spill procedure.

    Chapter 6 · Laundry on cleaning chemistry explains how alkalis and surfactants act on soil, and Chapter 8 · Laundry on oxidizers and finishing agents contains the hazardous mixtures in a laundry. Chapter 42 on soaking powder for removing stains from tableware uses the same carbonate calculation for a powder in the kitchen. Chapter 25 on chemical reactivity and incompatibility contains the separation of bases from acids, and Chapter 36 · Biology & Microbiology on respiration and workplace air covers irritant dust and vapors.

    Exercises and worked solutions

    The figures in the problems are for practice.

    Try to answer first, then open the worked solution.

    1. A container holds 20 kg of powder detergent. How many kilograms of sodium carbonate and how many kilograms of metasilicate does it contain according to the concentration ranges on the data sheet?

      Check my answer
      See the worked solution

      Its sodium carbonate is 0.30×20=60.30 \times 20 = 6 kg to 0.60×20=120.60 \times 20 = 12 kg, and its metasilicate is 0.10×20=20.10 \times 20 = 2 kg to 0.30×20=60.30 \times 20 = 6 kg. Those two basic salts add up to 8 to 18 kg, so that container holds mostly basic material.

    2. A washing machine holds 80 L of water. How many grams of powder give a concentration of 0.04 percent and of 0.09 percent, and is that figure enough to set the dose for a program?

      Check my answer
      See the worked solution

      A concentration of 0.04 percent means 0.4 g/L, that is, 80×0.4=3280 \times 0.4 = 32 g, and a concentration of 0.09 percent means 0.9 g/L, that is, 80×0.9=7280 \times 0.9 = 72 g. That figure is the use solution concentration according to the data sheet, but it is not yet enough to set the dose, because the dose also depends on the weight and soil level of the linen, the water hardness, and the program stage. The dose is set by the laundry supervisor together with the supplier according to the label.

    3. A worker breaks up lumps of powder with sweaty hands, feels no pain, and intends to wash their hands later at the break. What is wrong?

      Check my answer
      See the worked solution

      Sweat dissolves the powder into a concentrated basic solution on the skin, and alkali injuries may be painless at first and then progress over several hours. The powder is removed and the skin is rinsed with plenty of water right then, not later. Lumps are also not broken up by hand, because that work produces dust.

    4. A 1 percent solution is made from powder with a sodium carbonate content of 30 percent. What is its estimated pH from the carbonate alone?

      Check my answer
      See the worked solution

      A 1 percent solution contains 10 g of powder per liter, so its carbonate is 0.30×10=30.30 \times 10 = 3 g/L and C=3/105.99=0.0283C = 3/105.99 = 0.0283 mol/L. With the formula in this chapter x=0.00235x = 0.00235 mol/L, so pH =14.00+log⁡0.00235=11.37= 14.00 + \log 0.00235 = 11.37. A solution that dilute is still clearly basic.

    5. Powder is kept in an open drum beside the washing machine and measured with an aluminum scoop that is often wet. What must be changed?

      Check my answer
      See the worked solution

      The drum is given a lid that is always kept on and is moved away from the machine’s steam, because the two main salts of that powder bind water and cake. The scoop is replaced with a measuring scoop that is clean, dry, and not aluminum, because a wet scoop carries water into the container and basic salts may attack aluminum. The supervisor decides on the storage place and on procuring the scoop.

    6. A little powder has spilled on the floor, and a worker is about to pour acid neutralizer on it to make it neutral. What is the decision?

      Check my answer
      See the worked solution

      The powder is not doused with acid. Carbonate and acid produce carbon dioxide gas and foam that can carry basic material and acid into the surroundings, and acids are incompatible materials according to the data sheet. The powder is cleaned up according to the spill procedure without raising dust, with eye protection and gloves.

    References

    External sources

    • Chemistry 2eopenstax.org
    • Washing, Cleaning, and Polishing Materialsnvlpubs.nist.gov
    • Inert Ingredient Tolerance Reassessments: Two Exemptions from the Requirement of a Tolerance for Alkyl (C8-C24) Benzenesulfonic Acid and its Ammonium, Calcium, Magnesium, Potassium, Sodium, and Zinc Saltsepa.gov
    • Sodium hydroxide: incident managementassets.publishing.service.gov.uk
    • Safe use of cleaning substances in the hospitality industryhse.gov.uk
    • Chemicals - safe use and handlinghse.gov.uk
    • Basic advice on first aid at workhse.gov.uk
    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
    • COSHH frequently asked questionshse.gov.uk

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Laundry powder detergent: sodium carbonate, metasilicate, alkylbenzene sulfonate, and alcohol ethoxylate, the 0.04 to 0.09 percent solution, dust and skin, moisture and caking, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/deterjen-serbuk-laundry-natrium-karbonat-metasilikat-alkil-benzena-sulfonat-dan-alkohol-etoksilat-larutan-0-04-sampai-0-09-persen-debu-dan-kulit-kelembapan-dan-penggumpalan-serta-penanganan-dan-penyimpanan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A container holds 20 kg of powder detergent. How many kilograms of sodium carbonate and how many kilograms of metasilicate does it contain according to the concentration ranges on the data sheet?

    2

    A washing machine holds 80 L of water. How many grams of powder give a concentration of 0.04 percent and of 0.09 percent, and is that figure enough to set the dose for a program?

    3

    A worker breaks up lumps of powder with sweaty hands, feels no pain, and intends to wash their hands later at the break. What is wrong?

    Self-assessment progress0%

    Nearby chapters