Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Chemistry · Chapter 54Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Laundry neutralizer based on sodium metabisulfite

    content of 30 to 60 percent, solution pH 3.5 to 5, sulfur dioxide gas on contact with acids, people with asthma, and handling and storage

    Laundry neutralizer powder touched by traces of an acid product gives off a smell of burning sulfur, and the first person to become short of breath is often not the person holding the scoop. This chapter covers laundry neutralizer based on sodium metabisulfite from the side of its chemistry: a content of 30 to 60 percent and pH 3.5 to 5 in a 1 percent solution according to the manufacturer’s safety data sheet for one product of this class, why this salt releases sulfur dioxide gas on contact with acids, the gas concentrations that already affect people with asthma, the limit values in air, the ban on bringing it together with chlorine bleach, dust and the eyes, first aid, and handling and storage. Dosing rates and dispenser settings are not given. Spills that are already giving off gas, the health assessment of workers with asthma, and treating a casualty are stated as work for other parties.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    In the chemical room of a hotel laundry, the neutralizer powder in a lidded bucket had caked because of damp. An operator broke up the lumps with a scoop that had just been used to measure out rust remover, which is an acid product, and had not been rinsed. A sharp smell like burning sulfur rose from the bucket. The operator coughed a few times, then went on working. A colleague at the folding table, a few meters away, had had asthma since childhood. Within a few minutes their chest felt tight and their breathing became noisy, although they had not touched anything.

    That sequence can be explained from what was in the bucket. The neutralizer powder was based on sodium metabisulfite, a salt that releases sulfur dioxide gas on contact with acids. HSE, the British occupational safety authority, records metabisulfite as a respiratory irritant that narrows the airways of people who already have asthma, and at higher doses causes similar reactions in people who do not have asthma. According to HSE, the characteristics of those reactions point to sulfur dioxide liberated from the metabisulfite. Laundry staff need to know what is in that powder, which materials make it give off gas, and who is affected first.

    Scope

    This chapter covers one class of product, namely laundry neutralizer powder based on sodium metabisulfite: its contents and the pH of its solution, the gas released on contact with acids, the effect of that gas on people with asthma, the materials it must not meet, dust and the eyes, personal protective equipment, first aid, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of this class. Other products may differ, so what applies is the label and the safety data sheet of the product in use.

    This chapter is study material, not a work instruction. Dosing rates, the stage at which the neutralizer enters, and dispenser settings are not given; all of them are read from the product label and set by the chemical supplier. The function of neutralizers and antichlors within the cycle is in Chapter 8 · Laundry on oxidizers and finishing agents, the final rinse pH is in Chapter 9 · Laundry on pH and chemical measurement throughout the cycle, programs and doses are in Chapter 11 · Laundry on wash program architecture and Chapter 12 · Laundry on sorting, program design, and dose scaling, and dispensers are in Chapter 1 · Chemical Dispensing on peristaltic dispensers and Chapter 2 · Chemical Dispensing and Chapter 3 · Chemical Dispensing on laundry dispensers.

    How to check a data sheet is in Chapter 26 on reading the safety data sheets of cleaning products, labels and spills are in Chapter 6 · Safety on chemicals in technician work, and laundry work hazards in general are in Chapter 21 · Laundry on laundry occupational safety and health (K3). Two products that are often in the same room are covered in Chapter 53 on chlorine bleach for laundry and Chapter 55 on acid laundry softeners.

    Work outside the authority of laundry operators and building technicians: setting the dose and adjusting the dispenser, handling powder that is already giving off gas or large spills, judging whether a worker with asthma may work in the chemical room, and giving treatment other than first aid. The dose and the dispenser belong to the chemical supplier or the dispenser technician, gas incidents and large spills belong to trained personnel or the emergency response team, and the health assessment and treatment belong to a doctor or the emergency services.

    What the product contains: sodium metabisulfite at 30 to 60 percent

    According to the manufacturer’s safety data sheet for one product of this class, this neutralizer is a powder for laundry use. Only one ingredient is listed, namely sodium metabisulfite with CAS number 7681-57-4 at 30 to 60 percent. The pH of a 1 percent solution is written as 3.5 to 5. The written classification of the product is acute toxicity category 4 if swallowed, category 3 if inhaled, and category 2 through the skin, together with serious eye damage category 1. That data sheet was issued on October 16, 2024 and is valid until October 15, 2029, and it contains no dosing figure.

    Sodium metabisulfite, with the formula Na₂S₂O₅, is a sulfur salt in the form of white to yellowish crystals or powder with an odor of sulfur dioxide, and is also known as sodium pyrosulfite. Its molar mass is 190.1 g/mol. In the Great Britain mandatory classification and labeling list, the pure substance falls in acute toxicity category 4 if swallowed and serious eye damage category 1, with a supplemental statement coded EUH031.

    A content of 30 to 60 percent means that 40 to 70 percent of what is in the package is other material that is not listed. The data sheet also names its use only as a laundry product. In the laundry, an acid material that enters at the final rinse is called a neutralizer and a material that breaks down chlorine bleach residue is called an antichlor; Chapter 8 · Laundry covers both and names sodium metabisulfite among its examples of antichlors. How the product works inside the machine is a question for the supplier.

    An acidic solution: pH 3.5 to 5

    The pH scale expresses the hydronium ion concentration in a solution, with pH =−log⁡[H3O+]= -\log[\text{H}_3\text{O}^+]; pure water at 25 °C has a pH of 7.00. The figure 3.5 to 5 on the data sheet means that a 1 percent solution of this product is acidic. The name neutralizer refers to its job of dealing with base residue in the fabric, not to its solution being neutral.

    That acidity comes from the same family of sulfur compounds. Sulfurous acid, H₂SO₃, is a solution of sulfur dioxide in water; this acid is unstable, cannot be isolated as a pure substance, and gives the sulfur dioxide back when its solution is heated. Sulfurous acid ionizes in two steps, forming the hydrogen sulfite ion, HSO₃⁻, and then the sulfite ion, SO₃²⁻, with the constants Ka1=1.2×10−2K_{a1} = 1.2 \times 10^{-2} and Ka2=6.2×10−8K_{a2} = 6.2 \times 10^{-8}. In general chemistry, a metabisulfite ion that dissolves is written as reacting with water to become hydrogen sulfite ions; this equation is not quoted from a document opened for this chapter:

    S2O52−+H2O→2 HSO3−\text{S}_2\text{O}_5^{2-} + \text{H}_2\text{O} \rightarrow 2\,\text{HSO}_3^-

    The fraction of the sulfur that is present as sulfurous acid at a given pH can be estimated from the first constant:

    r=[H2SO3][HSO3−]=[H3O+]Ka1,f=r1+rr = \frac{[\text{H}_2\text{SO}_3]}{[\text{HSO}_3^-]} = \frac{[\text{H}_3\text{O}^+]}{K_{a1}}, \qquad f = \frac{r}{1 + r}

    where rr is the ratio of the sulfurous acid concentration to the hydrogen sulfite ion concentration, [H3O+][\text{H}_3\text{O}^+] is the hydronium ion concentration in mol/L, and ff is the fraction present as sulfurous acid, without units. This formula ignores the sulfite ion, whose amount is very small at a pH below 5, and treats the solution as dilute and ideal. At pH 4 almost all the sulfur is present as hydrogen sulfite ions; at pH 1 most of it is already sulfurous acid (Example 4).

    Sulfur dioxide gas on contact with acids

    Chemistry textbooks describe a convenient way to make sulfur dioxide in the laboratory: a strong acid is reacted with a sulfite salt or a hydrogen sulfite salt. Sulfurous acid forms first, then quickly decomposes into sulfur dioxide and water. That reaction, deliberate in the laboratory, is the same one that happened in the bucket in the opening case. The acid product residue on the scoop lowered the pH at the point of contact, hydrogen sulfite turned into sulfurous acid, and the sulfurous acid decomposed into gas.

    The Great Britain mandatory classification list gives sodium metabisulfite the code EUH031. In British health guidance, that code reads: contact with acids liberates toxic gas.

    The data sheet for the product of this class also names acids among the incompatible materials. In the laundry, the acid products that may be nearby include rust remover, liquid acid-based neutralizers, and the acid softeners covered in Chapter 55.

    The amount of gas is not small. One formula unit of Na₂S₂O₅ contains two sulfur atoms, so it forms at most two molecules of sulfur dioxide. With a molar mass for sulfur dioxide of 64.1 g/mol, the upper limit is 2×64.1/190.1=0.6742 \times 64.1/190.1 = 0.674 g of gas for each gram of sodium metabisulfite. Less than half a gram of product that reacts completely is already enough to bring the air of a small closed room to the short-term exposure limit value (Example 3).

    Heat and damp also matter. NIOSH, the United States occupational safety and health institute, notes that sodium metabisulfite decomposes on heating and is slowly oxidized to the sulfate on exposure to air and moisture. A package that is always kept tightly closed protects the quality of the product and the air in the room at the same time.

    Sulfur dioxide and people with asthma

    The UK Health Security Agency (UKHSA) describes sulfur dioxide as a colorless gas with an irritating, pungent odor. This gas dissolves in the moisture on skin, eyes, and mucous membranes and then forms sulfurous acid, which damages tissue. People who inhale it may have irritation of the eyes and nose, sore throat, cough, chest tightness, and wheeze, and a buildup of fluid in the lungs may take up to 36 hours to appear. It is 2.25 times as heavy as air, so this gas tends to collect in the low parts of a room.

    The concentrations that cause trouble differ widely between people with asthma and healthy people. UKHSA summarizes reports from other bodies as follows:

    Concentration in airWhat is reported
    from 0.1 to 0.25 ppmairway resistance increases in people with asthma who are exercising
    0.54 to 1 ppmthe odor begins to be noticed and mucous membranes are irritated
    1 to 8 ppmin healthy people: faster breathing, cough, and sore throat
    100 ppmimmediately dangerous to life and health

    The first two rows explain the opening case. People with asthma can be affected at a concentration that the person next to them cannot yet smell (Example 6), so air without an odor is not necessarily safe for them.

    HSE judges the evidence that metabisulfite causes new asthma in workers to be insufficient: there is only one well-documented case of occupational asthma, in a worker who used sodium metabisulfite powder. What is clear according to HSE is its nature as an irritant that triggers airway narrowing in people who already have asthma. For that reason workers with asthma are not placed in the chemical room without a doctor’s assessment, and any breathing symptom is reported to the supervisor.

    Threshold limit value (Indonesian nilai ambang batas, NAB) is the time-weighted average concentration that workers can accept without resulting in disease or health problems, for work of no more than 8 hours a day or 40 hours a week. The annex to Permenaker 5/2018 (Minister of Manpower Regulation) lists sodium metabisulfite with a NAB of 5 mg/m³ and the remark upper respiratory tract irritation. For sulfur dioxide, that annex gives no NAB and lists the figure 0.25 in the short-term exposure or ceiling column, printed in the mg/m³ sub-column, with the remark impaired lung function and lower respiratory tract irritation. As of November 2026 that regulation has the status in force on JDIH Kemnaker. For comparison, the British workplace exposure limit for sulfur dioxide is 0.5 ppm or 1.3 mg/m³ for 8 hours and 1 ppm or 2.7 mg/m³ for 15 minutes.

    Chlorine bleach, bases, and metals

    This neutralizer must not meet chlorine bleach in the concentrated state, whether the bleach is a powder or a liquid. There are two reasons. First, its solution is acidic, and UKHSA notes that sodium hypochlorite decomposes on contact with acids and produces toxic and corrosive gases, including chlorine. Second, sodium hypochlorite is a strong oxidizer that reacts with reducing materials to the point of creating a fire and explosion hazard. Sulfite compounds are among the materials that are easily oxidized: strong oxidizing agents oxidize sulfurous acid, and sulfite solutions exposed to air always contain sulfates.

    That ease of oxidation is put to use inside the machine, where chlorine residue that is already very dilute is broken down in the rinse water as described in Chapter 8 · Laundry. Outside the machine, the rule is firm: neutralizer powder is not mixed with chlorine bleach, is not measured with the same scoop or measuring jug, is not stored on the same shelf or tray, and its dispenser line is not swapped. HSE gives hospitality workers one short rule: never mix cleaning substances.

    The data sheet for the product of this class names three incompatible materials: acids, bases, and metals. Base products in the laundry, for example those covered in Chapter 49 on laundry alkali builders, are stored and measured separately. Metals are the reason for choosing a plastic scoop and keeping the product’s original container.

    Dust, the eyes, and personal protective equipment

    NIOSH records the exposure routes of sodium metabisulfite as inhalation, ingestion, and skin and eye contact, with the symptoms irritation of the eyes, skin, and mucous membranes. The Great Britain mandatory classification puts the eyes as the most serious target, namely serious eye damage category 1. Fine powder is easily raised when the package is opened, when the powder is scooped, and when lumps are broken up.

    The HSE guidance for cleaning substances in hospitality applies to that work:

    • Powders are always taken with a scoop, never by hand.
    • The protective clothing provided is always worn when handling substances, especially concentrates, and eye protection such as goggles or a visor is worn if there is any danger of splashing.
    • Substances are used only in well-ventilated areas. Mechanical ventilation is switched on and checked to be working, and a mask and goggles are worn if the manufacturer’s instructions call for them.
    • Where tap water is not available for eye irrigation, at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers is provided.

    The type of respiratory protection and gloves is read from the data sheet of the product in use and chosen according to Chapter 5 · Safety on personal protective equipment.

    First aid

    First aid follows the workplace procedure. For sodium metabisulfite NIOSH specifies immediate eye irrigation, fresh air for anyone who has inhaled it, and immediate medical attention for anyone who has swallowed it. The NIOSH and HSE guidance in detail:

    1. Eyes. The eyes are immediately washed with large amounts of water while occasionally lifting the upper and lower lids, then the casualty gets medical attention immediately.
    2. Skin. Powder or solution that gets on the skin is washed away with plenty of water. If irritation persists, the casualty seeks medical advice and tells the employer.
    3. Swallowed. The casualty gets medical attention immediately.
    4. Inhaled dust or gas. The casualty is moved to fresh air at once. For gas inhaled in large amounts, the casualty is kept warm and at rest and gets medical attention as soon as possible. If breathing has stopped, a trained first aider gives artificial respiration and the emergency services are called.

    A person who is short of breath after inhaling the gas is still examined by a doctor even if they feel better, because fluid in the lungs may take up to 36 hours to appear. The product label or data sheet is taken to the doctor.

    Handling and storage

    The manufacturer’s safety data sheet for one product of this class gives a storage temperature of minus 15 to 50 °C. That upper limit agrees with the NIOSH note that this material decomposes on heating. Packages are kept away from steam pipes, dryers, and ironers.

    HSE gives guidance on storing and handling cleaning substances in hospitality:

    • Substances are kept in their original labeled containers, with lids, and securely stored.
    • The storage place is away from heat, sunlight, foodstuffs, and members of the public, especially children. The manufacturer’s storage instructions are checked because some products need to be stored separately from others.
    • Spills on floors or work surfaces are cleaned up immediately, and the workplace has a spill procedure.
    • Staff are trained and supervised. Just issuing data sheets is not enough.

    For this product, separately means away from acid products, chlorine bleach, and base products, each with its own tray and scoop. The package is closed tightly as soon as the powder has been taken. Spilled powder is handled according to the workplace procedure and Chapter 6 · Safety, and is not flushed with another product. Because the gas is heavier than air, the ventilation of the chemical room needs to work down to near the floor.

    Worked example

    The figures in the examples below are practice figures, unless their origin is stated. The gas calculations assume that all the sulfur is released as sulfur dioxide and is mixed evenly into the air of a room without ventilation, so the results are upper limits that show the order of magnitude.

    Example 1: sodium metabisulfite in one package and in a 1 percent solution. A 20 kg package contains 0.30×20=6.00.30 \times 20 = 6.0 kg to 0.60×20=12.00.60 \times 20 = 12.0 kg of sodium metabisulfite. A 1 percent solution, the state for which the pH is written on the data sheet, contains 10 g of product in 1,000 g of solution. The sodium metabisulfite in it is 0.30×10=3.00.30 \times 10 = 3.0 g to 0.60×10=6.00.60 \times 10 = 6.0 g, or 0.3 to 0.6 percent of the solution.

    Example 2: the most sulfur dioxide from 100 g of product. One hundred grams of product contains 30 to 60 g of sodium metabisulfite. With the upper limit of 0.674 g of gas per gram, the sulfur dioxide that can be released is 30×0.674=20.230 \times 0.674 = 20.2 g to 60×0.674=40.460 \times 0.674 = 40.4 g. A handful of powder doused with acid can release tens of grams of gas.

    Example 3: how much product it takes to reach the limit value in a small room. A chemical room measuring 4 m by 3 m by 3 m has a volume of 4×3×3=364 \times 3 \times 3 = 36 m³. The British limit value for 15 minutes, 2.7 mg/m³, is matched by 36×2.7=97.236 \times 2.7 = 97.2 mg of sulfur dioxide. That much gas comes from 97.2/0.674=14497.2/0.674 = 144 mg of sodium metabisulfite, that is 144/0.60=240144/0.60 = 240 mg of product at 60 percent or 144/0.30=480144/0.30 = 480 mg of product at 30 percent. Less than half a gram of powder that reacts completely with acid already matches that limit value.

    Example 4: the fraction present as sulfurous acid at pH 4 and pH 1. At pH 4, the hydronium ion concentration is 1.0×10−41.0 \times 10^{-4} mol/L, so r=1.0×10−4/1.2×10−2=0.0083r = 1.0 \times 10^{-4}/1.2 \times 10^{-2} = 0.0083 and f=0.0083/1.0083=0.0082f = 0.0083/1.0083 = 0.0082, that is 0.8 percent. At pH 1, the hydronium ion concentration is 0.10 mol/L, so r=0.10/0.012=8.3r = 0.10/0.012 = 8.3 and f=8.3/9.3=0.89f = 8.3/9.3 = 0.89, that is 89 percent. A solution whose pH is around 4 holds almost all of its sulfur as dissolved ions. A strong acid that lowers the pH to 1 turns almost nine tenths of it into sulfurous acid, which then decomposes into gas.

    Example 5: product dust and the NAB. The NAB of 5 mg/m³ applies to sodium metabisulfite, not to all of the product dust. Dust from product at 60 percent contains 5 mg of sodium metabisulfite in 5/0.60=8.35/0.60 = 8.3 mg of dust, and product at 30 percent in 5/0.30=16.75/0.30 = 16.7 mg of dust. In a 36 m³ room, the figure 5 mg/m³ is matched by 36×5=18036 \times 5 = 180 mg of sodium metabisulfite in the air, that is 180/0.60=300180/0.60 = 300 mg to 180/0.30=600180/0.30 = 600 mg of product dust. That amount is less than one gram.

    Example 6: odor does not protect people with asthma. The odor begins to be noticed at 0.54 ppm, whereas the airway resistance of people with asthma already increases from 0.1 to 0.25 ppm. The concentration that can only just be smelled is 0.54/0.25=2.20.54/0.25 = 2.2 to 0.54/0.1=5.40.54/0.1 = 5.4 times higher. The British limit value for 8 hours, 0.5 ppm, is also 0.5/0.25=20.5/0.25 = 2 to 0.5/0.1=50.5/0.1 = 5 times above that concentration. A room that has no odor and is still below the limit value for workers may already be affecting a colleague who has asthma.

    Stop conditions

    1. A sharp smell like burning sulfur comes from the neutralizer package, bucket, tray, or dispenser, or someone nearby is coughing, short of breath, or wheezing: stop work and everyone goes out to fresh air. The supervisor calls trained personnel or the building’s emergency response team, and anyone with symptoms is examined by a doctor.
    2. Neutralizer powder meets an acid product, or meets chlorine bleach in powder or liquid form: keep away from the container, do not stir it, do not flush it, and clear the area. Trained personnel or the emergency response team deal with it.
    3. A person is short of breath, wheezing, or has chest pain after inhaling gas or dust: call the emergency services. The casualty is examined by a doctor even if they feel better.
    4. Powder or solution gets in the eyes: stop work and rinse immediately with water. The casualty is taken to a doctor or the emergency services.
    5. A worker who has asthma or a lung disease is assigned to measure out, move, or clean up a spill of neutralizer: do not start. The supervisor asks for a doctor’s assessment first.
    6. The neutralizer scoop, measuring jug, tray, or dispenser line has been used for an acid product, chlorine bleach, or a base product and has not been cleaned, or the dispenser tubing is unmarked: do not use it. The supervisor provides dedicated tools, and the dispenser technician or the supplier marks the line.
    7. A package without a label, a bulging package, powder that is wet or caked and smells, or a safety data sheet that is missing or past its validity date: do not open it and do not use it. The supervisor asks the supplier for an explanation.
    8. The chemical room ventilation is off, or eye protection and an eyewash facility are not available: do not measure out powder. The supervisor and the building technician restore the ventilation and the equipment first.
    9. A spill larger than the local spill kit can handle, or a spill wetted by wash water or by another product: clear the area and hand over to trained personnel or the emergency response team.
    10. The neutralizer runs out much faster or much more slowly than usual, or linen comes out smelling of sulfur: the operator does not change the dosing rate or the dispenser setting. The chemical supplier or the dispenser technician checks it.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    It is called a neutralizer, so the material is neutral and safe.

    Why is it wrong?

    Its 1 percent solution has a pH of 3.5 to 5, the pure substance falls in serious eye damage category 1, and the powder releases toxic gas on contact with acids.

    Common misconception

    If there is no odor, the air is safe.

    Why is it wrong?

    People with asthma can be affected from 0.1 to 0.25 ppm, whereas the odor is only noticed at 0.54 ppm.

    Common misconception

    Mixing an acid with an acid does no harm.

    Why is it wrong?

    This neutralizer solution is indeed acidic, but a stronger acid turns hydrogen sulfite into sulfurous acid, which decomposes into sulfur dioxide.

    Common misconception

    Neutralizer is used to remove chlorine residue, so it may be mixed with bleach to make it safe.

    Why is it wrong?

    The breakdown of chlorine residue takes place only in rinse water that is already very dilute. In the concentrated state, chlorine bleach meets an acid material and a reducing material at once, and that is prohibited.

    Common misconception

    A dust mask is enough for working in a room that smells of sulfur.

    Why is it wrong?

    A dust mask holds back powder, not gas, and a room that smells is left.

    Chapter 8 · Laundry on oxidizers and finishing agents explains the place of neutralizers and antichlors within the cycle, and Chapter 9 · Laundry on pH and chemical measurement throughout the cycle gives the way to check the result at the final rinse. Chapter 25 on chemical reactivity and incompatibility contains the segregation of materials in storage, and Chapter 40 · Buildings & Facilities on indoor air quality covers ventilation and air measurement.

    Exercises and worked solutions

    The figures in the problems are used for practice.

    Try to answer first, then open the worked solution.

    1. A 25 kg package contains product with 30 to 60 percent sodium metabisulfite. How many kilograms of sodium metabisulfite are in it, and how many kilograms of sulfur dioxide at most can be released?

      Check my answer
      See the worked solution

      The sodium metabisulfite is 0.30×25=7.50.30 \times 25 = 7.5 kg to 0.60×25=15.00.60 \times 25 = 15.0 kg. The most sulfur dioxide is 7.5×0.674=5.067.5 \times 0.674 = 5.06 kg to 15.0×0.674=10.115.0 \times 0.674 = 10.1 kg. One package can release several kilograms of toxic gas on contact with acid.

    2. A room measures 5 m by 4 m by 3 m. How many milligrams of sulfur dioxide match 2.7 mg/m³, and how many grams of product at 60 percent can release it?

      Check my answer
      See the worked solution

      The room volume is 5×4×3=605 \times 4 \times 3 = 60 m³, so the gas is 60×2.7=16260 \times 2.7 = 162 mg. That gas comes from 162/0.674=240162/0.674 = 240 mg of sodium metabisulfite, that is 240/0.60=400240/0.60 = 400 mg or 0.40 g of product. Less than half a gram of product that reacts completely already matches that figure.

    3. A neutralizer solution with a pH of 4 is hit by an acid product so that its pH falls to 2. What fraction of its sulfur is present as sulfurous acid, and what does that mean?

      Check my answer
      See the worked solution

      At pH 2 the hydronium ion concentration is 0.010 mol/L, so r=0.010/0.012=0.83r = 0.010/0.012 = 0.83 and f=0.83/1.83=0.45f = 0.83/1.83 = 0.45, that is 45 percent. Almost half of its sulfur is already sulfurous acid, which decomposes into gas, whereas at pH 4 that fraction is less than 1 percent. Work is stopped and the area is left.

    4. A supervisor intends to assign a worker who has asthma to refill the neutralizer container, because that worker “has never complained about the smell.” What is the decision?

      Check my answer
      See the worked solution

      The assignment does not go ahead before there is a doctor’s assessment, because the airways of people with asthma already narrow at a concentration that cannot yet be smelled. The absence of complaints about the smell is no measure, since the odor is only noticed at a concentration 2 to 5 times higher. It is the supervisor who asks for that assessment, not the worker.

    5. In the chemical room there is only one scoop, used in turn for chlorine bleach powder and neutralizer powder. What is wrong, and who changes it?

      Check my answer
      See the worked solution

      The same scoop carries chlorine bleach residue, which is a strong oxidizer, into a powder that is acidic and easily oxidized, and the other way round. The two must not meet in the concentrated state. The supervisor provides a dedicated scoop marked for each product, and the two packages are moved to separate storage places.

    6. A neutralizer bucket is found left open overnight near a steam pipe. The powder is caked and smells. The operator intends to break up the lumps and use it. What must be done?

      Check my answer
      See the worked solution

      The powder is not broken up and not used, because heat decomposes the material and damp air oxidizes it, and the smell shows that gas has already been released. The operator leaves the room and reports it. The supervisor asks the supplier for an explanation about the product and moves the storage place away from the steam pipe.

    References

    External sources

    • NIOSH Pocket Guide to Chemical Hazards - Sodium metabisulfitecdc.gov
    • First Aid Procedures for Chemical Hazardscdc.gov
    • Sulphur dioxide: incident managementassets.publishing.service.gov.uk
    • Asthmagen? Critical assessments of the evidence for agents implicated in occupational asthmahse.gov.uk
    • The GB mandatory classification and labelling list (GB MCL List)hse.gov.uk
    • Sodium hypochlorite: incident managementassets.publishing.service.gov.uk
    • Chemistry 2eopenstax.org
    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
    • Safe use of cleaning substances in the hospitality industryhse.gov.uk

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Laundry neutralizer based on sodium metabisulfite: content of 30 to 60 percent, solution pH 3.5 to 5, sulfur dioxide gas on contact with acids, people with asthma, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/penetral-laundry-berbahan-natrium-metabisulfit-kadar-30-sampai-60-persen-ph-larutan-3-5-sampai-5-gas-sulfur-dioksida-bila-bertemu-asam-orang-berasma-serta-penanganan-dan-penyimpanan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A 25 kg package contains product with 30 to 60 percent sodium metabisulfite. How many kilograms of sodium metabisulfite are in it, and how many kilograms of sulfur dioxide at most can be released?

    2

    A room measures 5 m by 4 m by 3 m. How many milligrams of sulfur dioxide match 2.7 mg/m³, and how many grams of product at 60 percent can release it?

    3

    A neutralizer solution with a pH of 4 is hit by an acid product so that its pH falls to 2. What fraction of its sulfur is present as sulfurous acid, and what does that mean?

    Self-assessment progress0%

    Nearby chapters