By Kurnia · Published November 15, 2026 · Version 1 · 21 min read
Laundry alkali builders
sodium carbonate powders with metasilicate and sodium hydroxide, liquid sodium hydroxide at 10 to 30 percent, stated pH, dust and splashes, and handling and storage
Laundry alkali powder that sticks to a sweaty forearm causes no pain, then becomes a wound an hour later. This chapter covers laundry alkali builders from the side of their chemistry according to the manufacturer’s safety data sheets for three products of this class: a sodium carbonate powder with metasilicate, a sodium carbonate powder with sodium hydroxide and metasilicate, and a liquid with sodium hydroxide at 10 to 30 percent. It covers concentration ranges, what a pH figure means for a 1 percent solution and with the note 100 percent, hazard classes, powder dust and liquid splashes, incompatible materials, personal protective equipment, first aid, and handling and storage. Dosing rates and dispenser settings are not given. Dosing, dispenser repair, large spills, and treating a casualty are stated as work for other parties.
This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.
In a hotel laundry, a bag of alkali powder that had been open for several days caked in the humid air. A worker broke up the lumps with a scoop over the measuring container. Dust rose to their face, their eyes stung, and they coughed. A little powder stuck to their sweaty forearm. The arm did not hurt, so they carried on working, and only an hour later did the skin turn red and sting.
That powder contained sodium carbonate, sodium hydroxide, and metasilicate, which become a basic solution as soon as they meet water, including sweat and tears. The UK Health Security Agency (UKHSA) notes that alkali injuries to the skin may be painless at first, so that treatment is delayed, and may keep progressing over several hours. In the same room there is often a jerry can of liquid alkali, a concentrated sodium hydroxide solution that a dispenser pumps to the washing machine. Both belong to one functional class, but the powder reaches people as dust, while the liquid reaches them as splashes and drips.
Scope
This chapter covers one class of laundry product, namely alkali builders, in three forms: a sodium carbonate powder with metasilicate, a sodium carbonate powder with sodium hydroxide and metasilicate, and a sodium hydroxide liquid. It covers contents, pH, hazard classes, dust and splashes, incompatible materials, personal protection, first aid, and storage. The product data come from the manufacturer’s safety data sheets for three products of this class. Other products may differ, so what applies is the label and the data sheet of the product in use.
This chapter is study material, not a work instruction. Dosing rates, concentrations in the machine, dispenser settings, and the sequence of a wash program are not given; all of them are read from the product label, the dispenser manual, and the workplace procedure. How alkali acts on soil is in Chapter 6 · Laundry on cleaning chemistry, pH from stage to stage is in Chapter 9 · Laundry on pH and chemical measurement throughout the cycle, dosing is in Chapter 12 · Laundry on sorting, program design, and dose scaling, and dispensers are in Chapter 1 · Chemical Dispensing on peristaltic dispensers.
How to check a data sheet and what the hazard categories mean are in Chapter 26 on reading safety data sheets for cleaning products, labels and spills are in Chapter 6 · Safety on chemicals in technician work, and the choice of protection is in Chapter 5 · Safety on personal protective equipment. Powder detergent is covered in Chapter 51 on laundry powder detergent, and the acid products that must not meet concentrated alkali are in Chapter 54 on laundry neutralizers.
Work outside the authority of laundry attendants and building technicians: setting the dose, adjusting or repairing the dispenser, handling large spills or spills mixed with an acid product, and giving treatment other than first aid. Dosing and the dispenser belong to the dispenser technician or the chemical supplier, large spills belong to trained personnel or the emergency response team, and casualties are handled by a doctor or the emergency services.
Three products of this class: contents and concentration ranges
An alkali builder is a substance or product that raises the pH of the wash solution and provides a reserve of base for the detergent. The table below gives the contents of three products of this class according to their manufacturer’s safety data sheets, with CAS numbers in parentheses and concentrations in percent.
| Product | Ingredients listed | pH as written | Classification as written |
|---|---|---|---|
| Powder A, soluble in water | sodium carbonate (497-19-8) 60 to 100; disodium metasilicate (6834-92-0) 10 to 30; alcohols, C12 to C16, ethoxylated (68551-12-2) 5 to 10; sodium dodecylbenzenesulfonate (25155-30-0) 1 to 5; two other organic ingredients (7128-64-5 and 16090-02-1) 1 to 3 each | 11.6 to 12.6 for a 1 percent solution | acute oral toxicity category 4; skin corrosion category 1A; serious eye damage category 1; specific target organ toxicity, single exposure, category 3 (respiratory tract) |
| Powder B, partly soluble in water | sodium carbonate (497-19-8) 30 to 60; sodium hydroxide (1310-73-2) 10 to 30; sodium metasilicate pentahydrate (10213-79-3) 10 to 20 | 12.5 to 13.5 with the note 100 percent | corrosive to metals category 1; skin corrosion or irritation category 1; serious eye damage category 1 |
| Liquid C, soluble in water | sodium hydroxide (1310-73-2) 10 to 30, the only ingredient listed | 13.0 to 14.0 with the note 100 percent | corrosive to metals category 1; skin corrosion category 1A; serious eye damage category 1 |
All three data sheets were issued in 2024 and are valid until 2029. Powder A and Powder B are described as laundry detergents for industrial and professional use, and both are written as sold ready to use. Liquid C is described as a laundry product that is dosed automatically through a dispenser, with a relative density of 1.3 to 1.34. The two language versions of the Powder A data sheet give different concentrations for the ethoxylated alcohols: 5 to 10 percent in the English version and 3 to 5 percent in the Indonesian version.
A concentration range is the interval in which the actual concentration lies, not a recipe (Example 1). Powder A contains two surfactants alongside its basic ingredients, so it is also a detergent; surfactants are covered in Chapter 21 on surfactants, colloids, and emulsions. Powder B contains sodium hydroxide in the same concentration range as Liquid C, so a powder must not be regarded as milder only because it is dry.
Where the basicity comes from and what the pH figures mean
Sodium hydroxide, with the formula NaOH, is an ionic compound that in its pure form is a white, odorless solid and is also known as caustic soda. A strong base is a base that breaks up almost completely into ions when it dissolves in water. Sodium hydroxide belongs to that group, so the hydroxide ion concentration of its solution equals the sodium hydroxide concentration in mol/L.
Sodium carbonate, with the formula Na₂CO₃, is a salt whose solution is basic. Carbonate is a moderately strong base, because the carbonate ion accepts a hydrogen ion from water and leaves a hydroxide ion behind:
For a carbonate solution with a concentration of mol/L, the hydroxide ion concentration satisfies
with and , the second ionization constant of carbonic acid, so that . This formula holds at 25 °C, assumes an ideal solution, and ignores the other ingredients in the powder, so its result shows the order of magnitude, not a measured value. For sodium hydroxide, is simply its concentration in mol/L. The role of metasilicate, which is listed in both powders, is covered in Chapter 6 · Laundry.
A pH figure on a data sheet is read together with its concentration note. For Powder A, pH 11.6 to 12.6 applies to a 1 percent solution. Carbonate alone at that concentration gives a pH of about 11.5 to 11.6 (Example 2), so the lower end of the range agrees with its carbonate content. For Liquid C, the note 100 percent means the undiluted product. A calculation from its concentration gives a figure above 14 (Example 4), so the figure 14 is read as the upper end of the customary pH scale, not as a precise measured value. For Powder B, the data sheet does not explain which solution was measured under the note 100 percent; even its 1 percent solution already has a pH above 12 (Example 3).
Hazard classes: skin, eyes, respiratory tract, and metals
All three data sheets list serious eye damage category 1 and skin corrosion. Powder A is also classified as harmful if swallowed and irritating to the respiratory tract, while Powder B and Liquid C are corrosive to metals.
In the Great Britain classification and labeling regulation quoted by UKHSA, a concentration of 5 percent or more falls in skin corrosion category 1A, 2 to less than 5 percent in category 1B, and 0.5 to less than 2 percent irritates the skin and eyes. The 10 to 30 percent in Powder B and Liquid C equals 2 to 6 times that 5 percent limit.
UKHSA explains how a base injures. A base saponifies fats and dissolves proteins and collagen, the tissue softens, and the base penetrates until it causes burns through the full thickness of the skin. In the eye, a basic solution may damage all layers of the eye, so the event is treated as an eye emergency. When inhaled, sodium hydroxide irritates the eyes, nose, and throat, and when swallowed it causes burning in the mouth, throat, and stomach.
In its guidance for the textiles industry, the British occupational safety authority (HSE) names soda ash, the common name of sodium carbonate, among the chemicals that can cause skin irritation, itchy and stuffy noses, sneezing, and sore eyes. The written classification of Powder A is more severe than that, so Powder A is handled as a corrosive material. The HSE guidance sheet for laundry rooms on offshore installations sums it up: heavy-duty cleaning products may cause skin irritation, burns, or serious eye damage.
Powder dust and liquid splashes
Powder reaches people when the bag is opened, the contents are scooped, and the measured amount is poured. Its dust gets in the eyes and is inhaled, and powder that sticks to damp skin becomes a concentrated solution on the spot. Sodium hydroxide reacts with water in the air, so Powder B left open may become damp and cake, and breaking up the lumps adds to the dust.
Permitted ceiling concentration (Indonesian kadar tertinggi diperkenankan, KTD) is the concentration of a chemical in workplace air that must not be exceeded even for an instant while workers are doing their work. The annex to Permenaker (Minister of Manpower Regulation) 5/2018 lists sodium hydroxide with the figure 2 mg/m³ in the permitted short-term exposure or KTD column, with no 8-hour threshold limit value, and with the note irritation of the upper respiratory tract, skin, and eyes. As of November 2026 that regulation is listed as in force on JDIH Kemnaker, the ministry’s legal documentation site. NIOSH, the United States occupational safety and health institute, uses the same figure as a ceiling limit. Less than two grams of Powder B suspended in a medium-sized laundry room already equals that figure (Example 6).
Liquid reaches people as splashes and drips when the jerry can is changed, the suction tube is pulled out, or a connection leaks. Sodium hydroxide does not evaporate readily, so what is inhaled from the liquid is mist, not vapor. Similar opening points on a dispenser are covered in Chapter 37 on liquid machine dishwashing detergent.
The HSE sheet for laundry rooms recommends liquid detergent rather than powder, and measured-volume dispensers so that detergents and chemicals are not poured. For dispensing points in the textiles industry, HSE asks that corrosives are not poured straight from small containers into buckets, because the liquid splashes back as air enters to replace the contents; what is used instead is a valve, a pump, or an enclosed handling system. Scoops and buckets must be clean and dry, because cross-contamination of incompatible substances may set off a violent reaction.
Dosing through a dispenser and powder measured by hand
The data sheet for Liquid C states that the product is dosed automatically through a dispenser, while the data sheets for both powders state that the product is sold ready to use. None of the three gives a dosing rate. For that reason this chapter gives no dosing rate. The dose and the pump settings come from the chemical supplier and from the wash program.
A dispenser is also a hazard control. HSE asks employers to avoid pouring from bulk containers and to minimize handling by using siphons or pumps. That system opens when the jerry can, the tubing, or the squeeze tube is changed, and changing the squeeze tube and calibrating are the dispenser technician’s work.
Powder measured by hand has no such protection. Eye protection and gloves are put on before the bag is opened, and the measuring scoop is used for one product only. Powder goes into water, not water into powder: HSE asks that acids and corrosives are always added to water, never the other way around.
Incompatible materials: acids, metals, and organic materials
The data sheets name acids and metals as incompatible materials for all three products, and organic materials for Powder B.
| Material | What happens | Rule of thumb |
|---|---|---|
| Acid products, for example neutralizers and acid softeners | sodium hydroxide solutions react violently with acids and release heat; carbonates react with acids to form a salt, water, and carbon dioxide gas | never mixed; stored and measured separately |
| Aluminum, zinc, tin, and lead | attacked by sodium hydroxide that is wet or in solution, releasing flammable hydrogen gas | not used as scoops, buckets, drip trays, or shelving |
| Cloth, paper, and cardboard | solid sodium hydroxide in contact with water may generate enough heat to ignite combustible materials | spilled powder is not thrown into a bin holding wet cloth or paper |
As a rule of thumb, HSE asks that acids are kept separate from alkalis, in bays marked for each. The HSE sheet for hospitality workers gives a short rule: never mix cleaning substances. The same sheet warns that products containing bleach, when mixed with acidic toilet cleaners or with ammonia, give off harmful gases. That prohibition is covered in Chapter 53 on chlorine bleach for laundry.
Personal protective equipment and first aid
For chemical dispensing points, HSE asks for gloves, overalls or aprons, work boots, and eye protection that are all chemical resistant, with clear rules on when that equipment must be worn. HSE also asks for a plentiful supply of running water near each dispensing point to douse a casualty. NIOSH recommends an eyewash and a quick-drench facility where sodium hydroxide is handled, and that work clothing that is wet or contaminated is removed. Glove materials and respiratory protection against dust are chosen according to Chapter 5 · Safety.
First aid follows the workplace procedure. NIOSH guidance for sodium hydroxide and HSE guidance for chemical injuries:
- Eyes. The eyes are immediately washed with large amounts of water while occasionally lifting the upper and lower lids, then the casualty is taken to medical attention immediately. HSE asks for the eye to be flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then for the casualty to be sent to hospital.
- Skin. The skin is immediately flushed with water. If the substance has soaked through clothing, the clothing is removed immediately and the skin is flushed, then the casualty gets medical attention. For chemical burns, HSE asks for the affected area to be flooded with water for 20 minutes, for contaminated clothing that is not stuck to the skin to be removed, and for the first aider to avoid being contaminated as well.
- Swallowed. The casualty is taken to medical attention immediately.
- Inhaled. The casualty is moved to fresh air at once, kept warm and at rest, and gets medical attention as soon as possible. If breathing has stopped, a trained first aider gives artificial respiration and the emergency services are called.
The UKHSA guidance for healthcare professionals prohibits giving neutralizing chemicals to a casualty who has swallowed a base, because the heat of the neutralization reaction may add to the injury. The guidance above uses water, not vinegar or any other acid product. The label or the product’s data sheet is taken to the doctor.
Handling and storage
The storage temperature as written differs for each product: 5 to 35 °C for Powder A, minus 5 to 40 °C for Powder B, and 5 to 45 °C for Liquid C. The data sheets for Powder B and Liquid C ask that the product is not stored near acids.
HSE gives storage guidance for cleaning substances in hospitality:
- Substances are kept in their original labeled containers, with lids, and securely stored.
- Stores are away from heat, sunlight, foodstuffs, and members of the public, especially children.
- The workplace has a spill procedure, and staff are trained until they understand the hazards and their controls.
The HSE sheet for laundry rooms adds a ventilated store, labels on display, the smallest practical amount in storage, and spill containment and spill clean-up kits. Powder is stored dry, and a bag that has been opened is closed tightly. Empty packaging is handled according to Chapter 35 · Water & Water Treatment on B3 waste in hotels, laundries, and workshops.
Worked example
The figures in the examples below are practice figures, unless their origin is stated. A 1 percent solution is read as 10 g of product per liter. A relative density of 1.32 is used as the midpoint of the range for Liquid C, so one milliliter of Liquid C has a mass of 1.32 g.
Example 1: a concentration range is not a recipe. The lower limits for Powder A add up to percent and the upper limits to percent, so all the ingredients cannot be at their upper limits at once. A 25 kg bag of Powder B holds kg to kg of sodium hydroxide.
Example 2: pH of a 1 percent solution of Powder A from carbonate alone. Ten grams of powder hold g to g of sodium carbonate. Its molar mass is g/mol, so its concentration is mol/L to mol/L. Solving the equation gives mol/L for the lowest concentration, so pOH and pH . For the highest concentration, mol/L, pOH , and pH . That result lies around the lower end of the pH range on the data sheet; the rest comes from the other basic ingredients in the powder.
Example 3: sodium hydroxide from Powder B in a 1 percent solution. Ten grams of Powder B hold g to g of sodium hydroxide. With a molar mass of 40.0 g/mol, its concentration is mol/L to mol/L. From sodium hydroxide alone, pH to . Its concentration is below the 0.5 percent limit, but its pH stays above 12.
Example 4: sodium hydroxide per liter and per jerry can of Liquid C. One liter of Liquid C has a mass of g. Its sodium hydroxide is g to g, that is, mol/L to mol/L. For the lowest concentration, the calculated pH , already above 14. A 20 L jerry can holds kg of product, with kg to kg of sodium hydroxide.
Example 5: water to rinse off a drip of Liquid C. Ten milliliters of Liquid C have a mass of g and at 30 percent hold g of sodium hydroxide. For the concentration to fall to 0.5 percent, the mass of the mixture has to be g, so g of water is needed, almost 0.8 L for 10 mL of product. That is why a drip on the skin is rinsed with plenty of water for a long time, not wiped off.
Example 6: Powder B dust and the figure 2 mg/m³. A laundry room measuring 6 m by 5 m by 3 m has a volume of m³. The figure 2 mg/m³ is equaled by mg of sodium hydroxide in the air. At 30 percent that corresponds to mg of Powder B, and at 10 percent to mg. This calculation assumes the dust is evenly spread; in front of the face of the person scooping, the concentration is higher.
Stop conditions
- Powder or liquid gets in the eyes, or on the skin even if it does not hurt: stop work and rinse immediately with water. The casualty is taken to a doctor or the emergency services.
- Someone swallows the product, or is short of breath and keeps coughing after inhaling dust or mist: call the emergency services. Do not give vinegar or any other neutralizing substance.
- Eye protection or gloves are missing or damaged, or there is no running water near the dispensing point: do not open the bag and do not change the jerry can. The laundry supervisor provides the equipment first.
- A bag or jerry can has no label, the label does not match the marking on the tube, or the safety data sheet is missing or past its validity date: do not use that product. The supervisor asks the supplier for an explanation.
- Alkali meets an acid product, or a container feels hot, hisses, or fizzes: keep away from the container and clear the area. The supervisor calls trained personnel or the building emergency response team.
- Spilled powder is more than the local spill kit can handle or is mixed with wet cloth and paper, or the powder in a bag has hardened into a block: do not sweep it dry, strike it, or hose it down. Trained personnel or the emergency response team handle the spill, and the supervisor decides what happens to that bag.
- The tubing, the squeeze tube, or a dispenser connection is dripping: keep people away from the drips and do not take the dispenser apart. The dispenser technician or the supplier does the repair.
- Product gets on aluminum or zinc-coated metal and the surface fizzes: stop and keep ignition sources away. The supervisor replaces that item with one that is suitable according to the label.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
Powder is safer than liquid because it does not splash.
Why is it wrong?
Powder B contains sodium hydroxide at 10 to 30 percent, the same as Liquid C, and reaches the eyes and the respiratory tract as dust. An alkali injury to the skin may also be painless at first.
Common misconception
It says ready to use, so it is safe to touch.
Why is it wrong?
That note concerns dilution, not hazard. The written classification of both powders is still skin corrosion and serious eye damage category 1.
Common misconception
If alkali gets on you, neutralize it with laundry neutralizer or vinegar.
Why is it wrong?
First aid guidance uses plenty of water for a long time. A neutralization reaction releases heat and may add to the injury.
Common misconception
The pH on the data sheet is the pH of the wash solution.
Why is it wrong?
The written pH applies to its note: a 1 percent solution for Powder A and 100 percent for the other two products. The pH in the machine is determined by the dose and is measured according to Chapter 9 · Laundry.
Links to other chapters
Chapter 6 · Laundry explains why the wash solution needs alkali and a buffer, and Chapter 9 · Laundry how pH and alkalinity are measured. Chapter 25 on chemical reactivity and incompatibility covers the separation of bases from acids, and Chapter 21 · Laundry on laundry occupational safety and health (K3) covers laundry work hazards in general.
Exercises and worked solutions
The figures in the problems are for practice.
Try to answer first, then open the worked solution.
How many kilograms of sodium hydroxide and of sodium carbonate are in a 20 kg bag of Powder B?
Check my answer
See the worked solution
The sodium hydroxide is kg to kg, and the sodium carbonate is kg to kg. One bag holds several kilograms of strong base.
Three milliliters of Liquid C go into one liter of water. What is the sodium hydroxide concentration in percent at both ends of the range, and what is the calculated pH?
Check my answer
See the worked solution
The mass of product is g, so its sodium hydroxide is g to g, or about 0.04 to 0.12 percent. Its concentration is mol/L to mol/L, so pH to . That solution is below the 0.5 percent limit, but it is still basic with a pH of about 12.
Powder B in a bag has caked. A worker intends to crush the lumps without gloves and then pour a little water over them. What is wrong?
Check my answer
See the worked solution
A damp lump of Powder B is a concentrated basic solution that injures the skin without pain at first, and solid sodium hydroxide releases heat when it meets water. That bag is closed and reported to the supervisor.
A 1 percent solution of Powder A is made from powder with 80 percent sodium carbonate. What is the calculated pH from carbonate alone, if solving the equation gives mol/L?
Check my answer
See the worked solution
The carbonate concentration is g per liter, that is, mol/L. With mol/L, pOH and pH . That figure lies between the two results of Example 2.
A jerry can of Liquid C and a jerry can of acid neutralizer stand side by side with unmarked tubes, and a zinc-coated bucket is used as a drip tray. What has to change, and who changes it?
Check my answer
See the worked solution
The two jerry cans are separated and both tubes are marked, because bases and acids react violently and release heat. The zinc-coated bucket is replaced with a plastic tray, because sodium hydroxide solution attacks zinc and releases hydrogen gas. The storage place is decided by the laundry supervisor, and the tubes are marked by the dispenser technician or the supplier.
A worker reads pH 12.5 to 13.5 on the data sheet for Powder B and concludes that the wash water in the machine has a pH of 13. What is the mistake?
Check my answer
See the worked solution
That pH is written with the note 100 percent, so it is not the pH of the wash solution, which is already very dilute. The pH in the machine is determined by the dose, the water, and the soil, and is read from a measurement according to Chapter 9 · Laundry.
References
External sources
- NIOSH Pocket Guide to Chemical Hazardscdc.gov
- Sodium hydroxide: incident managementassets.publishing.service.gov.uk
- Safe use of cleaning substances in the hospitality industryhse.gov.uk
- Basic advice on first aid at workhse.gov.uk
- Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
- Chemistry 2eopenstax.org
- Chemicals - safe use and handlinghse.gov.uk
- Laundry (OCE21, Offshore COSHH essentials)hse.gov.uk
Revision history
| Date | Version | Change |
|---|---|---|
| November 15, 2026 | 1 | First published |
How to cite
Kurnia (2026). Laundry alkali builders: sodium carbonate powders with metasilicate and sodium hydroxide, liquid sodium hydroxide at 10 to 30 percent, stated pH, dust and splashes, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/pembangun-alkali-laundry-serbuk-natrium-karbonat-dengan-metasilikat-dan-natrium-hidroksida-cairan-natrium-hidroksida-10-sampai-30-persen-ph-tertulis-debu-dan-percikan-serta-penanganan-dan-penyimpanan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.
How many kilograms of sodium hydroxide and of sodium carbonate are in a 20 kg bag of Powder B?
Three milliliters of Liquid C go into one liter of water. What is the sodium hydroxide concentration in percent at both ends of the range, and what is the calculated pH?
Powder B in a bag has caked. A worker intends to crush the lumps without gloves and then pour a little water over them. What is wrong?
Nearby chapters
Reading order by shelf: Chemistry · Chapter 50.
Reading order by shelf: Chemistry · Chapter 48.