Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Chemistry · Chapter 37Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Liquid machine dishwashing detergent

    sodium hydroxide at 10 to 30 percent, dosing through a dispenser, changing the jerry can and tubing, splashes and personal protective equipment, and handling and storage

    A few drops of machine dishwashing detergent that fall on a forearm while the jerry can is being changed cause no pain, then become a wound some time later. This chapter covers liquid machine dishwashing detergent from the side of its chemistry: sodium hydroxide at 10 to 30 percent and pH 14 according to the manufacturer’s safety data sheet for one product of this class, how a strong base saponifies fat and why the same reaction injures skin and eyes, the metals and materials it attacks, the dispenser as a closed system and the points where it leaks, the moments when the jerry can, the tubing, and the squeeze tube are changed, the limit value in air, personal protective equipment, first aid, and handling and storage. Dosing rates and dispenser settings are not given. Repairing the dispenser, large spills, and treating a casualty are stated as work for other parties.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    In the dishwashing area of a hotel, the machine detergent jerry can ran out in the middle of the lunch service. A worker pulled the suction tube out of the empty jerry can, and a few drops of liquid from the end of the tube fell on their forearm, just above the cuff of the glove. They felt nothing, so they connected the new jerry can and went back to loading racks. Half an hour later the skin at that spot was red and stinging, and only then was the arm rinsed.

    That sequence is typical of an injury from a strong base. The UK Health Security Agency (UKHSA) notes that alkali injuries to the skin may be painless at first, so that treatment is delayed, and may keep progressing over several hours. Liquid machine dishwashing detergent is a concentrated sodium hydroxide solution. All day long the liquid moves from the jerry can to the machine tank through tubing and a pump without being touched by anyone. People meet the concentrated liquid only at brief moments: when the jerry can is changed, when the tubing or the squeeze tube is changed, and when something leaks. Workers need to know what is in that jerry can, what it does to fat, skin, eyes, and metals, and at which points the closed system opens.

    Scope

    This chapter covers one class of product, namely strongly basic liquid detergent for commercial dishwashers that is dosed by a dispenser: its contents and pH, how it acts on soil, its hazards to the body, the materials it attacks, the contact points on the dispenser, personal protective equipment, first aid, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of this class. Other products may differ, so what applies is the label and the safety data sheet of the product in use.

    This chapter is study material, not a work instruction. Dosing rates, tank concentrations, dispenser settings, and the steps for changing a jerry can are not given; all of them are read from the product label, the dispenser manual, and the workplace procedure. The cycle and the meaning of dose are in Chapter 1 · Dishwashing on wash cycles, dosing, rinsing, sanitizing, and dispensers. The dispenser layout is in Chapter 4 · Chemical Dispensing on dishwasher dispensers, and detergent dosing is in Chapter 5 · Chemical Dispensing on dosing without a probe and Chapter 6 · Chemical Dispensing on dosing with a conductivity probe.

    How to check a data sheet is in Chapter 26 on reading safety data sheets for cleaning products, labels and spills are in Chapter 6 · Safety on chemicals in technician work, chemical burns are in Chapter 41 · Biology & Microbiology on skin and chemicals, and the choice of protection is in Chapter 5 · Safety on personal protective equipment. The two other jerry cans beside the machine are covered in Chapter 38 on dishwasher rinse additives and Chapter 39 on descalers for dishwashers and kitchen equipment. Sodium hydroxide for burnt-on deposits is in Chapter 35 on degreasers and burnt-on residue removers.

    Work outside the authority of dishwashing staff and building technicians: setting the dose and repairing the dispenser, handling large spills or spills mixed with an acid product, and giving treatment other than first aid. The dispenser belongs to the dispenser technician or the chemical supplier, large spills belong to trained personnel or the emergency response team, and casualties are handled by a doctor or the emergency services.

    What the product contains: sodium hydroxide at 10 to 30 percent

    According to the manufacturer’s safety data sheet for one product of this class, machine dishwashing detergent is a liquid that dissolves in water, is made for industrial and professional use, and is dosed by automatic setting through a dispenser. Only one ingredient is listed, namely sodium hydroxide with CAS number 1310-73-2 at 10 to 30 percent. The pH of the 100 percent product is written as 14, and its relative density is 1.180 to 1.210. Its classification is skin corrosion category 1A and serious eye damage category 1. That data sheet was issued on February 22, 2023 and is valid until February 21, 2028.

    Sodium hydroxide, with the formula NaOH, is an ionic compound that in its pure form is a white, odorless solid and is also known as caustic soda. A strong base is a base that breaks up almost completely into ions when it dissolves in water. Sodium hydroxide belongs to that group, and the hydroxide ions it releases act on soil as well as on body tissue.

    The hydroxide ion concentration and the pH can be estimated from the mass fraction:

    C=w×ρ×1,000M,pOH=−log⁡C,pH=14.00−pOHC = \frac{w \times \rho \times 1{,}000}{M}, \qquad \text{pOH} = -\log C, \qquad \text{pH} = 14.00 - \text{pOH}

    where CC is the hydroxide ion concentration in mol/L, ww is the mass fraction of sodium hydroxide as a decimal, ρ\rho is the density of the solution in g/mL, and MM is the molar mass, 40.0 g/mol. That relation between pH and pOH holds at 25 °C. This formula treats the solution as ideal, so for a solution as concentrated as this product the result only shows the order of magnitude. The calculation in Example 2 gives a figure above 14, so the figure 14 on the data sheet means the upper end of the usual pH scale, not a precise measured value.

    In the Great Britain classification and labeling regulation quoted by UKHSA, a sodium hydroxide solution at 5 percent or more falls in skin corrosion category 1A, at 2 to less than 5 percent in category 1B, and at 0.5 to less than 2 percent it irritates skin and eyes. The class on the data sheet for the product of this class agrees with those limits (Example 2). Other ingredients in the product are not known from the data sheet.

    Why a strong base cleans dishes and injures skin

    Fats are made up of fatty acid esters. Saponification is the reaction of fat with a base such as sodium hydroxide that produces glycerol and fatty acid salts, and those fatty acid salts are soap. Fat stuck to a dish does not dissolve in water, whereas glycerol and soap do. In the hot wash tank, the base helps turn the layer of fat into material that is carried away by the wash water.

    Skin and eyes are also made up of fats and proteins. UKHSA explains that alkalis damage tissue by saponifying fats and solubilizing proteins and collagen. The tissue softens, so the base can penetrate deeper and cause burns through the full thickness of the skin. Such an injury may be painless at first, may progress over several hours, and its extent is hard to assess because the skin discolors quickly. The reaction that lifts fat off a dish is the same as the reaction that injured the worker’s forearm in the opening case; the only difference is the material it met.

    In the eyes, alkaline solutions may penetrate and damage all layers of the eye, so UKHSA asks for such an event to be treated as an eye emergency. Inhaled mist irritates the eyes, nose, and throat, and a buildup of fluid in the lungs may take up to 36 hours to appear. If swallowed, the base immediately causes burning in the mouth, throat, and stomach.

    Materials that are attacked: aluminum, zinc, tin, acids, and air

    NIOSH, the United States occupational safety and health institute, notes that sodium hydroxide is incompatible with, among other things, water, acids, and metals such as aluminum, tin, and zinc, and that it is corrosive to metals. UKHSA adds that its solution attacks aluminum, tin, lead, and zinc while forming flammable hydrogen gas, reacts violently with acids, gives off heat on meeting acids or water, and readily reacts with carbon dioxide in the air to form sodium carbonate.

    MaterialWhat happensGuidance
    Aluminum: trays, pans, strainersattacked by a strong base; aluminum hydroxide is amphoteric and dissolves in strong basesconcentrated product is not collected in or placed on aluminum; the suitability of aluminum ware is read from the product label
    Zinc-coated or tin-coated steel: buckets, racks, cansattacked by the basic solution, releasing hydrogennot used as a container or a drip tray
    Acid products, for example a descalerreact violently and give off heat (Example 5)never mixed; stored separately
    Aircarbon dioxide turns sodium hydroxide into sodium carbonatethe jerry can is always kept closed

    The data sheet for the product of this class names acids as incompatible materials. HSE, the British occupational safety authority, gives one short rule for hospitality workers: never mix cleaning substances.

    Dosing through a dispenser: a closed system and the points where it opens

    The data sheet for the product of this class contains no dosing figure; all that is written is that the setting is automatic through a dispenser. For that reason this chapter gives no dosing rate; the target concentration comes from the chemical supplier.

    From the safety side, the dispenser is a hazard control device. HSE asks employers to avoid pouring from bulk containers and to minimize handling by using siphons or pumps. The dispenser does exactly that: a suction tube with a foot filter goes into the jerry can, the squeeze tube inside the peristaltic pump pushes the product along, and the discharge tube carries it to the injection point on the tank.

    As long as every connection is intact, nobody touches the concentrated liquid. The system opens at five points:

    1. The end of the suction tube. When it is pulled out of the jerry can, the tube and the foot filter are wet with concentrated product and drip.
    2. The mouth of the jerry can. A jerry can that is called empty still holds leftover product at the same concentration as a full one.
    3. The squeeze tube. A tube that bursts fills the pump housing with concentrated product.
    4. The connections and the injection point. A loose connection drips onto the floor or onto the top of the machine.
    5. Priming. When the tubing is primed after a change, a tube end that is not yet connected can spray product.

    Changing the jerry can, the tubing, and the squeeze tube

    The steps for a change follow the workplace procedure and the dispenser manual. This section only gives the reasons.

    Protection goes on before the jerry can is touched. Drips from the suction tube fall before a person has time to react, and the location of the eyewash is already known before the cap of the jerry can is opened.

    The label is matched first. Jerry cans of detergent, rinse additive, and descaler can be similar in size and color. HSE asks for every container to be clearly marked with its contents. Tubing that is marked by product keeps detergent out of the rinse line, and acid product out of the detergent line.

    The tube moves straight from the old jerry can to the new one. A tube laid on the floor or on a worktop leaves concentrated product where people work. A plastic tray catches the drips, and the contents of that tray are still corrosive (Example 3).

    Leftover product is not poured. HSE names splashes to the skin and eyes while a substance is being poured from one container into another as a risk, and prohibits transferring cleaning substances into food or drink containers. The empty jerry can is capped again and handled according to the label and Chapter 35 · Water & Water Treatment on B3 waste in hotels, laundries, and workshops.

    A full jerry can is a heavy load. The contents of a 20 L jerry can of this product have a mass of almost 24 kg (Example 6). The HSE guide to manual handling gives risk filter values: for a load held close to the body between knuckle height and elbow height, 25 kg for male workers and 16 kg for female workers. Near the floor the values drop to 10 kg and 7 kg. HSE stresses that those figures are not safe limits, only a filter for identifying low-risk tasks. Trolleys are covered in Chapter 9 · Safety on lifting and moving loads with equipment.

    The squeeze tube and the tubing are changed by an authorized person. The tube material differs for detergent and for rinse additive, and the pump rate changes after a tube is replaced, as explained in Chapter 7 · Chemical Dispensing on rinse aid dosing, maintenance, and troubleshooting of dishwasher dispensers. This work belongs to the dispenser technician or the supplier, unless the workplace procedure states otherwise.

    Health hazards, the limit value in air, and personal protective equipment

    NIOSH lists the exposure routes for sodium hydroxide as inhalation, ingestion, and skin and eye contact, with the symptoms irritation of the eyes, skin, and mucous membranes, pneumonitis, eye and skin burns, and temporary loss of hair. Its recommendations: skin and eye contact is prevented, work clothing that is wet or contaminated is removed, and an eyewash and a quick-drench facility are provided.

    Permitted ceiling concentration (Indonesian kadar tertinggi diperkenankan, KTD) is the concentration of a chemical in workplace air that must not be exceeded even for an instant while workers are doing their work. The annex to Permenaker (Minister of Manpower Regulation) 5/2018 lists sodium hydroxide with the figure 2 mg/m³ in the permitted short-term exposure or KTD column, with no 8-hour threshold limit value, and with the note irritation of the upper respiratory tract, skin, and eyes. As of November 2026 that regulation is listed as in force on JDIH Kemnaker, the ministry’s legal documentation site. NIOSH uses the same figure, 2 mg/m³, as a ceiling limit. Sodium hydroxide does not evaporate readily, so what can be inhaled is mist or fine spray, for example from a tube that sprays while it is being primed (Exercise 4).

    HSE guidance for cleaning substances in hospitality, whose list names dishwasher detergents:

    • The protective clothing provided is always worn when handling cleaning substances, especially concentrates.
    • Eye protection suitable for splash risks, for example goggles or a visor, is worn if there is any chance of splashing.
    • Rubber gloves are checked for holes, tears, and thin patches, and replaced if faulty. Latex gloves are avoided because they can cause reactions.
    • Where tap water is not available for rinsing the eyes, at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers is provided.

    The glove material is read from the product’s data sheet and the glove manufacturer’s chart, as covered in Chapter 5 · Safety.

    First aid

    First aid follows the workplace procedure. NIOSH guidance for sodium hydroxide and HSE guidance for chemical injuries:

    1. Eyes. The eyes are immediately washed with large amounts of water while occasionally lifting the upper and lower lids, then the casualty is taken to medical attention immediately. HSE asks for the eye to be flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then for the casualty to be sent to hospital.
    2. Skin. The skin is immediately flushed with water. If the liquid has soaked through clothing, the clothing is removed immediately and the skin is flushed, then the casualty gets medical attention. For chemical burns, HSE asks for the affected area to be flooded with water for 20 minutes, for contaminated clothing that is not stuck to the skin to be removed, and for the first aider to avoid being contaminated as well.
    3. Swallowed. The casualty is taken to medical attention immediately.
    4. Inhaled. The casualty is moved to fresh air at once, kept warm and at rest, and gets medical attention as soon as possible. If breathing has stopped, a trained first aider gives artificial respiration and the emergency services are called.

    The UKHSA general information for sodium hydroxide adds three things: contact lenses are removed and the eye is irrigated with lukewarm water, soiled clothing is removed without being pulled over the head, and washing of the skin or the eyes lasts at least 10 to 15 minutes, followed by medical advice. The UKHSA guidance for healthcare professionals prohibits giving neutralizing chemicals to a casualty who has swallowed a base, because the heat of the neutralization reaction may add to the injury. All of that guidance uses water, not vinegar or any other acid. Skin that has been splashed is rinsed even if it does not hurt. The label or the product’s data sheet is taken to the doctor.

    Handling and storage

    The manufacturer’s safety data sheet for one product of this class gives a storage temperature of 0 to 50 °C and names acids as incompatible materials. The detergent jerry can and the descaler jerry can may stand side by side next to the machine, so the separation and the labels at that spot are checked.

    HSE gives guidance on storing and handling cleaning substances in hospitality:

    • Substances are kept in their original labeled containers, with lids, and securely stored.
    • The storage place is away from heat, sunlight, foodstuffs, and members of the public, especially children. The manufacturer’s storage instructions are checked because some products need to be stored separately.
    • Spills on floors or work surfaces are cleaned up immediately, and the workplace has a spill procedure.
    • Staff are trained and supervised. Handing out data sheets alone is not enough.

    Full jerry cans are not stored on high shelves, because the HSE lifting filter values above shoulder height are as small as those near the floor. Small spills are handled according to Chapter 6 · Safety.

    Worked example

    The figures in the examples below are practice figures, unless their origin is stated. A relative density of 1.195 is used as the midpoint of the range on the data sheet, so one milliliter of product has a mass of 1.195 g.

    Example 1: sodium hydroxide per liter and per jerry can. One liter of product has a mass of 1.195×1,000=1,1951.195 \times 1{,}000 = 1{,}195 g. At 10 percent, the sodium hydroxide is 0.10×1,195=119.50.10 \times 1{,}195 = 119.5 g, and at 30 percent it is 0.30×1,195=358.50.30 \times 1{,}195 = 358.5 g. A 20 L jerry can holds 20×119.5=2,39020 \times 119.5 = 2{,}390 g to 20×358.5=7,17020 \times 358.5 = 7{,}170 g, that is, 2.39 to 7.17 kg of sodium hydroxide.

    Example 2: hydroxide ion concentration, pH, and the classification limit. The hydroxide ion concentration is 119.5/40.0=2.99119.5/40.0 = 2.99 mol/L to 358.5/40.0=8.96358.5/40.0 = 8.96 mol/L. For the lowest concentration, pOH =−log⁡2.99=−0.48= -\log 2.99 = -0.48, so pH =14.00+0.48=14.48= 14.00 + 0.48 = 14.48. That result is above 14 across the whole concentration range. Against the 5 percent limit for skin corrosion category 1A, the product concentration is 10/5=210/5 = 2 to 30/5=630/5 = 6 times higher, so the class on the data sheet agrees with its composition.

    Example 3: the water in the drip tray. Drips from the suction tube add up to 5 mL in a tray that holds 50 mL of water. At 30 percent, the sodium hydroxide is 5×1.195×0.30=1.795 \times 1.195 \times 0.30 = 1.79 g. The mass of the mixture is 5×1.195+50=55.9755 \times 1.195 + 50 = 55.975 g, so the concentration is 1.79/55.975=3.21.79/55.975 = 3.2 percent. That figure falls in the range of 2 to less than 5 percent, which is skin corrosion category 1B. The water in that tray is still corrosive.

    Example 4: the solution in the wash tank. With a practice concentration of 2 mL of product per liter of tank water, as in Chapter 5 · Chemical Dispensing, one liter holds 2×1.195=2.392 \times 1.195 = 2.39 g of product, that is, 0.10×2.39=0.2390.10 \times 2.39 = 0.239 g to 0.30×2.39=0.7170.30 \times 2.39 = 0.717 g of sodium hydroxide, or about 0.024 to 0.072 percent. That highest concentration is 0.5/0.072=6.90.5/0.072 = 6.9 times below the 0.5 percent limit. The hydroxide ion concentration is 0.239/40.0=0.005980.239/40.0 = 0.00598 mol/L to 0.717/40.0=0.01790.717/40.0 = 0.0179 mol/L, so the pH is 14.00+log⁡0.00598=11.7814.00 + \log 0.00598 = 11.78 to 14.00+log⁡0.0179=12.2514.00 + \log 0.0179 = 12.25. The tank solution is below the classification limits, but it is still basic with a pH of about 12, and its temperature is high.

    Example 5: heat on meeting an acid. In one calorimeter experiment, 50.0 mL of 1.00 mol/L hydrochloric acid and 50.0 mL of 1.00 mol/L sodium hydroxide released 2.9 kJ. The amount that reacted is 0.0500×1.00=0.05000.0500 \times 1.00 = 0.0500 mol, so the heat is 2.9/0.0500=582.9/0.0500 = 58 kJ per mole. One hundred milliliters of product at 30 percent holds 0.100×8.96=0.8960.100 \times 8.96 = 0.896 mol of sodium hydroxide. If all of it reacts with excess acid, the heat is 0.896×58=520.896 \times 58 = 52 kJ. If that heat is absorbed by 200 g of mixture with the specific heat of water, 4.184 J/g °C, the temperature rises by 52,000/(4.184×200)=6252{,}000/(4.184 \times 200) = 62 °C. A mixture that starts at 30 °C comes close to the boiling point of water, and a corrosive liquid that boils spatters. This rough calculation shows why this product must not meet an acid product.

    Example 6: lifting a jerry can. A 20 L jerry can holds 20×1.195=23.920 \times 1.195 = 23.9 kg of product. With an empty jerry can of 1.1 kg, the load is 23.9+1.1=25.023.9 + 1.1 = 25.0 kg. That load is 25.0/10=2.525.0/10 = 2.5 times the HSE filter value for male workers near the floor and 25.0/7=3.625.0/7 = 3.6 times the value for female workers. Lifting a full jerry can from the floor alone is far outside that filter, so a trolley or a smaller jerry can is discussed with the supervisor.

    Stop conditions

    1. Concentrated product gets in the eyes, or on the skin even if it does not hurt: stop work and rinse immediately with water. The casualty is taken to a doctor or the emergency services.
    2. Someone swallows the product, or is short of breath after inhaling mist: call the emergency services. Do not give vinegar or any other neutralizing substance.
    3. Eye protection or gloves are missing or damaged, or there is no eyewash near the machine: do not change the jerry can. The kitchen supervisor provides the equipment first.
    4. The jerry can has no label, the label does not match the marking on the tube, or the safety data sheet is missing or past its validity date: do not connect that jerry can. The supervisor asks the supplier for an explanation.
    5. The tubing, the squeeze tube, or a connection is dripping, or the pump housing is wet with product: keep people away from the drips and do not take the dispenser apart. The dispenser technician or the supplier does the repair.
    6. Detergent meets an acid product, or a container feels hot, hisses, or fizzes: keep away from the container and clear the area. The supervisor calls trained personnel or the building emergency response team.
    7. A spill is larger than the local spill kit can handle, or is flowing toward a food area: clear the area and hand it over to trained personnel or the emergency response team.
    8. Concentrated product gets on aluminum or zinc-coated metal and the surface fizzes, or aluminum ware comes out of the machine dull or blackened: stop and rinse. The supervisor asks the supplier about the suitability of the product.
    9. A full jerry can could only be moved by lifting it alone from the floor: do not lift it. The supervisor arranges a trolley, the help of a second person, or a smaller jerry can size.
    10. The jerry can empties much faster or much more slowly than usual: the operator does not change the dispenser settings. The dispenser technician checks it according to Chapter 5 · Chemical Dispensing and Chapter 6 · Chemical Dispensing.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    Machine detergent is just a more concentrated dish soap.

    Why is it wrong?

    It contains sodium hydroxide at 10 to 30 percent with the class skin corrosion category 1A. This product goes into the machine only through the dispenser.

    Common misconception

    If it does not hurt, it is nothing.

    Why is it wrong?

    An alkali injury to the skin may be painless at first and progress over several hours. Skin that has been splashed is rinsed right then.

    Common misconception

    If a base gets on you, neutralize it with vinegar.

    Why is it wrong?

    The available guidance uses large amounts of water for a long time. A neutralization reaction gives off heat and may add to the injury.

    Common misconception

    An empty jerry can is safe.

    Why is it wrong?

    The residue at the bottom of the jerry can has the same concentration as the full product. The empty jerry can is capped and handled according to the label.

    Common misconception

    The dispenser is automatic, so workers never touch the chemical.

    Why is it wrong?

    The dispenser closes the product path while it is working. That path opens when the jerry can, the tubing, or the squeeze tube is changed and when there is a leak.

    Chapter 26 on reading safety data sheets for cleaning products gives the way to check the data sheet that underlies this chapter. Chapter 4 · Chemical Dispensing to Chapter 7 · Chemical Dispensing cover the dispenser that carries this product to the machine, and Chapter 25 on chemical reactivity and incompatibility covers the separation of bases from acids. The heat of dilution and of neutralization is calculated in Chapter 12 on thermochemistry.

    Exercises and worked solutions

    The figures in the problems are for practice.

    Try to answer first, then open the worked solution.

    1. A 10 L jerry can holds product containing 30 percent sodium hydroxide with a relative density of 1.195. How many kilograms of sodium hydroxide does it hold?

      Check my answer
      See the worked solution

      The mass of product is 10×1.195=11.9510 \times 1.195 = 11.95 kg, so the sodium hydroxide is 0.30×11.95=3.5850.30 \times 11.95 = 3.585 kg. Even a small jerry can holds several kilograms of strong base.

    2. Two milliliters of product at 10 percent drip into 20 mL of water. What is the sodium hydroxide concentration of that mixture in percent, and which classification range does it fall in?

      Check my answer
      See the worked solution

      The mass of product is 2×1.195=2.392 \times 1.195 = 2.39 g and the sodium hydroxide is 0.10×2.39=0.2390.10 \times 2.39 = 0.239 g. The mass of the mixture is 2.39+20=22.392.39 + 20 = 22.39 g, so the concentration is 0.239/22.39=1.070.239/22.39 = 1.07 percent. That figure falls in the range of 0.5 to less than 2 percent, which still irritates skin and eyes.

    3. A worker gets a drip of product on the wrist while changing a jerry can. It does not hurt, and they intend to rinse it later, after the rush. What is wrong?

      Check my answer
      See the worked solution

      An alkali injury may be painless at first and keep progressing over several hours, so delaying the rinse deepens the injury. The skin is rinsed with water right then, and the event is then reported to the supervisor and checked by a doctor.

    4. A dishwashing room measures 5 m by 4 m by 3 m. How many milligrams of sodium hydroxide in the air equal the figure of 2 mg/m³, and how many milliliters of product at 20 percent contain that amount?

      Check my answer
      See the worked solution

      The room volume is 5×4×3=605 \times 4 \times 3 = 60 m³, so the figure of 2 mg/m³ is equaled by 2×60=1202 \times 60 = 120 mg of sodium hydroxide in the air. At 20 percent that corresponds to 120/0.20=600120/0.20 = 600 mg of product, that is, 0.600/1.195=0.500.600/1.195 = 0.50 mL. Half a milliliter of product mist already equals that figure, so the tubing is not primed with an open end.

    5. A kitchen wants to wash aluminum trays in the machine that uses this detergent, and to use a zinc-coated bucket as a drip tray. What is the decision?

      Check my answer
      See the worked solution

      Sodium hydroxide solution attacks aluminum and zinc and releases hydrogen gas, so a zinc-coated bucket is not used as a drip tray; a plastic tray is used. The suitability of the aluminum trays is read from the product label and asked of the supplier by the supervisor.

    6. The detergent jerry can and the acid descaler jerry can stand side by side on the floor, and neither suction tube is marked. What has to change, and who does it?

      Check my answer
      See the worked solution

      The two jerry cans are separated and the two tubes are marked by product, because a base and an acid react violently and give off heat when they meet. The storage place is decided by the kitchen supervisor, and the tubes are marked by the dispenser technician or the supplier.

    References

    External sources

    • NIOSH Pocket Guide to Chemical Hazards - Sodium hydroxidecdc.gov
    • First Aid Procedures for Chemical Hazardscdc.gov
    • Sodium hydroxide: incident managementassets.publishing.service.gov.uk
    • Sodium hydroxide: general informationgov.uk
    • Safe use of cleaning substances in the hospitality industryhse.gov.uk
    • Basic advice on first aid at workhse.gov.uk
    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
    • Chemistry 2eopenstax.org
    • Manual handling at work: A brief guidehse.gov.uk

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Liquid machine dishwashing detergent: sodium hydroxide at 10 to 30 percent, dosing through a dispenser, changing the jerry can and tubing, splashes and personal protective equipment, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/deterjen-cair-mesin-pencuci-piring-natrium-hidroksida-10-sampai-30-persen-takaran-lewat-dispenser-mengganti-jeriken-dan-selang-percikan-dan-alat-pelindung-diri-serta-penanganan-dan-penyimpanan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A 10 L jerry can holds product containing 30 percent sodium hydroxide with a relative density of 1.195. How many kilograms of sodium hydroxide does it hold?

    2

    Two milliliters of product at 10 percent drip into 20 mL of water. What is the sodium hydroxide concentration of that mixture in percent, and which classification range does it fall in?

    3

    A worker gets a drip of product on the wrist while changing a jerry can. It does not hurt, and they intend to rinse it later, after the rush. What is wrong?

    Self-assessment progress0%

    Nearby chapters