Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Chemistry · Chapter 39Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Descalers for dishwashers and kitchen equipment

    strong mineral acid and pH 1 to 2, limescale, machine materials sensitive to acid, rinsing, the ban on mixing with chlorine, and handling and storage

    At a hospital in California, an employee exposed for less than one minute to the vapor from a bucket of bleach and acid cleaner felt a burning throat for more than 24 hours. This chapter covers liquid descalers for dishwashers and kitchen equipment from the side of the chemical itself: pH 1 to 2 and a relative density of 1.19 to 1.23 according to the manufacturer’s safety data sheet for one product of this class, the acid name that is inconsistent within that document and how to check it with a calculation, how acid dissolves limescale, machine metals sensitive to acid, rinsing, the ban on mixing with chlorine products, threshold limit values, personal protective equipment, first aid, and handling and storage. How to run descaling on a machine is not repeated, and the dose for a particular machine is read from the label and the manual. Descaling boilers and pipes, repairing etched metal, large spills, and treating casualties are stated as the work of other parties.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    On November 3, 1989, at a state hospital in California, a patient who was taking part in cleaning duties poured a 4 percent phosphoric acid cleaner into a bucket holding bleach and water. A cloud of stinging vapor formed at once. The employee who was supervising led the patient out, then went back and emptied the bucket into a sink. The employee was exposed for less than one minute, but the burning in the throat and nose lasted more than 24 hours, and full recovery took 36 hours.

    The cleaner’s label did not name its active ingredient and did not warn of the danger of mixing. Two other phosphoric acid products at that hospital, one of them at 30 percent, likewise carried no information about a reaction with hypochlorite. A jerry can of descaler in a hotel dishwashing room is a similar case: a concentrated acid liquid stored near detergent, sanitizer, and bleach. The people who use it need to know what is in it, which metals it damages, and why that liquid must not meet chlorine products. For one product of this class, the data sheet itself does not agree on the name of its acid.

    Scope

    This chapter covers liquid descalers that are strongly acidic and are used for dishwashers and kitchen equipment: the contents according to the data sheet, how acid dissolves limescale, machine materials sensitive to acid, rinsing, the ban on mixing with chlorine products, health hazards, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of this class. What applies in the workplace is the label and the data sheet of the product actually in use.

    This chapter is learning material, not a work instruction. How to run descaling on a machine is in Chapter 9 · Dishwashing on dishwasher water quality, softeners, scale, and descaling, and is not repeated. The dose for a particular machine, contact time, solution temperature, and neutralizer recipes are not given; all of them are read from the product label and the machine manual.

    How to check a data sheet is in Chapter 26 on reading the safety data sheets of cleaning products. Chlorine products in the kitchen are covered in Chapter 41 on concentrated sodium hypochlorite and chlorinated sanitizing powder and Chapter 42 on soaking powder for removing stains from tableware.

    Work outside the authority of dishwashing staff and building technicians: descaling the boiler, the booster, and the water pipes inside a machine, repairing metal, seals, or heating elements damaged by acid, handling a large spill or a spill that has mixed with a chlorine product, and giving treatment other than first aid. The inside of the machine belongs to the machine manufacturer’s technician, large spills belong to trained personnel or the emergency response team, and casualties are handled by a doctor or the emergency services. The product is chosen by the kitchen supervisor together with the chemical supplier and the machine manufacturer.

    What the product contains according to the data sheet: strong mineral acid and pH 1 to 2

    A descaler, also called a delimer, is an acid product used to dissolve mineral deposits left by water on machines and equipment. According to the manufacturer’s safety data sheet for one product of this class, the product is an aqueous solution with a pH of 1 to 2 for the undiluted product and a relative density of 1.19 to 1.23. The product as sold is classified as skin corrosion category 1A and serious eye damage category 1, and its dilution information reads 1 : 1 to 5. The data sheet was issued on February 22, 2023 and is valid until February 21, 2028.

    The name of the acid cannot be established from that document. The composition table lists nitric acid, CAS number 7697-37-2, at a concentration of 10 to 30 percent. The regulatory information section gives a concentration of 10.5 percent, and the English version of the same document gives 10.05 percent. The transport section gives a different name, namely phosphoric acid. This chapter does not decide which is correct and calls the contents a strong mineral acid, in the sense of an inorganic acid solution at pH 1 to 2 that is corrosive. A mineral acid is an inorganic acid, for example nitric acid, phosphoric acid, and hydrochloric acid. That mismatch is a reason to ask the supplier for a written explanation before the product is used.

    A strong acid is an acid whose ionization in water is practically complete, whereas a weak acid ionizes only partly. Nitric acid is a strong acid and also a strong oxidizing agent, whereas phosphoric acid is a weak acid with a first ionization constant of Ka1=7.5×10−3K_{a1} = 7.5 \times 10^{-3}. A pH value does not reveal the name of the acid, because pH only states the hydrogen ion concentration:

    pH=−log⁡[H+],[H+]=10−pH\text{pH} = -\log [\text{H}^+], \qquad [\text{H}^+] = 10^{-\text{pH}}

    with [H+][\text{H}^+] in mol/L. A pH of 1 to 2 corresponds to 0.1 to 0.01 mol/L of hydrogen ions, and that figure can be reached by a dilute strong acid as well as by a concentrated weak acid (Example 4).

    The table below summarizes the notes of NIOSH, the United States occupational safety and health institute, for the two acids. As long as the name of the acid is uncertain, the rule to follow is the stricter of the two columns.

    ItemNitric acidPhosphoric acid
    Toward metalscorrosive to metalsreacts with metals and releases flammable hydrogen gas
    Incompatible withcombustible materials, metallic powders, hydrogen sulfide, carbides, and alcoholsstrong caustics and most metals; solutions containing bleach or ammonia
    Symptoms of exposureirritation of the eyes, skin, and mucous membranes; delayed pulmonary edema, pneumonitis, bronchitis; dental erosionirritation of the eyes, skin, and upper respiratory system; burns of the eyes and skin; dermatitis
    An eyewash and a quick-drench facilityrecommended for solutions with a pH below 2.5recommended for solutions above 1.6 percent

    Limescale: why acid works and why the acid runs out

    Limescale is a mineral deposit, mainly calcium carbonate, that is left behind when hard water is heated or evaporates. Calcium carbonate is sparingly soluble in water, but its solubility rises sharply in an acidic solution because the carbonate ion is basic and is bound by hydrogen ions. With enough acid, the reaction runs through to carbon dioxide gas:

    CaCO3(s)+2 H+(aq)→Ca2+(aq)+H2O(l)+CO2(g)\text{CaCO}_3(s) + 2\,\text{H}^+(aq) \rightarrow \text{Ca}^{2+}(aq) + \text{H}_2\text{O}(l) + \text{CO}_2(g)

    The fizzing that appears when a descaler touches scale is that carbon dioxide. A guide to the maintenance of industrial water systems published by the United States military in 2005, now archived, notes that the escaping gas helps to stir the solution, and that the reaction is considered complete when the foam subsides or the acid is used up.

    Two limits follow from that equation. Each mole of calcium carbonate uses up two moles of hydrogen ions, so a given amount of solution dissolves only a given amount of scale (Example 5). Acid also works only on minerals that are basic, so fat, protein residue, and starch films are not its target. Scale that remains is dealt with by repeating the treatment according to the label and the machine manual, not by adding another product.

    Machine materials sensitive to acid

    The acid that dissolves scale also attacks the metal under the scale. That water system maintenance guide states that a cleaning agent is selected for its ability to dissolve the deposit, its safety hazards, and its effect on the metals involved. An inhibited acid is a cleaning acid to which special inhibitors have been added so that the acid does not attack the base metal while the scale still dissolves. Whether a given product contains an inhibitor can be learned only from its supplier.

    MaterialWhat happens with acidRule
    Stainless steelprotected by a thin layer of chromium oxide; hydrochloric acid is not used because its chloride ion can cause pitting and stress corrosion crackingonly the product named in the machine manual; contact time according to the label
    Galvanized steelthe zinc coating corrodes at a pH below 6not soaked in descaler solution and not flushed with it
    Aluminumreacts with acids as well as bases and releases hydrogen gasnot exposed, unless the label states that it is safe
    Copper, brass, and silvernitric acid dissolves copper and silver and produces nitrogen oxidesthe component is removed or protected; ask the machine manufacturer
    Carbon steel and cast ironphosphoric acid is corrosive to ferrous metals and their alloysnot used as a container, stirrer, or funnel

    The fizzing from scale dies down when the scale is gone, whereas bubbles that keep coming from metal that is already clean mean that the metal itself is reacting. Brown fumes are nitrogen dioxide, which forms when nitric acid meets a metal such as copper. Both are signs to stop.

    The same guide gives two further limits. Components that the cleaning could damage are removed first, and chemical cleaning is not appropriate when corrosion is so advanced that removing the deposit will open up many leaks. The dishwasher manuals summarized in Chapter 9 · Dishwashing on dishwasher water quality, softeners, scale, and descaling divide the work: the parts the operator can reach may be cleaned according to the instructions, whereas the boiler and all water pipes are left to the manufacturer’s technician. Oven steam generators are covered in Chapter 3 · Commercial Kitchens on combi ovens.

    Rinsing

    Descaler solution must not be left in a machine or on equipment that touches food. Residual acid keeps working on metal and seals, then meets detergent or sanitizer at the next use. The example procedures in that water system maintenance guide always end with draining, thorough rinsing, and a check of the pH of the rinse water. Machine manuals ask for something similar: the agent is not left in for hours, then the machine is run with an empty rack to rinse.

    When a tank is drained and then refilled with clean water again and again, each fill dilutes the residue left behind. For an acid that is fully ionized:

    pHn=pH0+nlog⁡Vv\text{pH}_n = \text{pH}_0 + n \log \frac{V}{v}

    with pH0\text{pH}_0 the pH of the solution before draining, nn the number of fills and drains, VV the volume of fill water (L), and vv the volume of residue left at the bottom of the tank, in the pump, and in the pipes (L). This formula assumes that the residue mixes evenly and that the rinse water neutralizes nothing, and it holds only while the result is below the pH of the rinse water. For a weak acid the rise in pH per rinse is smaller. The number of rinses follows the manual and is checked with pH paper on the last rinse water.

    Residual acid is not neutralized with alkaline detergent or another product on one’s own initiative. The data sheet names bases as incompatible materials, and a neutralizer, if one is called for, follows the machine manual and the product label.

    The ban on mixing with chlorine

    The manufacturer’s data sheet for one product of this class states the ban plainly: do not mix with bleach or other chlorinated products, because chlorine gas will form. The reaction is the same as in the opening case:

    OCl−+Cl−+2 H+→Cl2+H2O\text{OCl}^- + \text{Cl}^- + 2\,\text{H}^+ \rightarrow \text{Cl}_2 + \text{H}_2\text{O}

    HSE, the British occupational safety authority, says the same for the food industry: chlorine-based disinfectants release toxic chlorine gas when in contact with acid, and incompatible chemicals are stored separately. According to the report on the California incidents, a level of about 3 ppm can already cause severe irritation of the eyes and respiratory tract, whereas the odor is usually not detectable until above 3.5 ppm, so the absence of odor is not a sign of safety.

    In a dishwashing room, the sources of chlorine include sodium hypochlorite solution, sanitizing powders and soaking powders that release chlorine, and machine detergents with active chlorine. Four routes by which they meet need to be closed:

    1. Dosing still running. The chlorinated detergent dispenser stays on when descaler solution is already in the tank.
    2. The same container. A bucket, measuring jug, funnel, or soaking tub is used in turn for acid and for chlorine products.
    3. Floor and sink. A descaler spill is mopped up with chlorinated sanitizer, or two leftover solutions are emptied into the same sink.
    4. Storage. A jerry can of acid is placed next to a jerry can of hypochlorite, so a leak from one container reaches the other.

    The HSE rule for workers is short: never mix cleaning substances.

    Health hazards, threshold limit values, and personal protective equipment

    NIOSH records the same routes of entry for the two acids in the table, namely inhalation, ingestion, and skin and eye contact. A guide to cleaning products from EPA, the United States environmental agency, states that acid solutions are corrosive at pH 0 to 2 and produce severe burns on contact, and names descalers as an example of an acidic product. Dilution according to the data sheet does not change that pH much (Example 3). Chemical burns are explained in Chapter 41 · Biology & Microbiology on the skin and chemicals.

    The threshold limit value (Indonesian nilai ambang batas, NAB) is the time-weighted average concentration that workers can accept without harm to health for a time not exceeding 8 hours a day or 40 hours a week. The permitted short-term exposure (Indonesian pajanan singkat diperkenankan, PSD) is the airborne concentration that must not be exceeded for a short exposure of not more than 15 minutes. Permenaker (Minister of Manpower Regulation) 5/2018 sets the NAB of nitric acid at 2 parts per million or 5.2 mg/m³ and the PSD at 4 parts per million or 10 mg/m³, the NAB of phosphoric acid at 1 mg/m³ and the PSD at 3 mg/m³, and the NAB of chlorine at 0.5 parts per million and the PSD at 1 part per million. As of November 2026 the regulation is listed as in force on JDIH Kemnaker, the legal documentation site of the Ministry of Manpower.

    The HSE rules for cleaning substances in hospitality:

    • The protective clothing provided is always worn when handling concentrates, and eye protection such as goggles or a visor is worn if there is any chance of splashing.
    • Rubber gloves are checked for holes and tears, and latex gloves are avoided.
    • When diluting, the concentrate is added to the water, not the water to the concentrate.
    • Cleaning substances are used only in well-ventilated areas, with mechanical ventilation switched on and working.
    • For disinfectants in the food industry, HSE writes that work with soak tanks, buckets, and brushes often requires an impermeable apron, gauntlets, and safety spectacles or a visor, and that tipping a large jerry can to dilute is extremely poor practice. That rule applies to acid concentrates as well.

    The glove material and the need for respiratory protection are read from the data sheet of the product in use, with the method of selection in Chapter 5 · Safety on personal protective equipment.

    First aid

    NIOSH gives the same actions for nitric acid and phosphoric acid, so the following rules apply whatever the name of the acid:

    1. Eyes. The eyes are immediately washed with large amounts of water while occasionally lifting the upper and lower lids, then the casualty is taken to medical attention immediately. HSE asks for the eye to be flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then for the casualty to be sent to hospital.
    2. Skin. The skin is immediately flushed with water. If the liquid penetrates the clothing, the clothing is removed immediately and the skin is flushed, then the casualty gets medical attention. For chemical burns, HSE asks for the affected area to be flooded with water for 20 minutes, for contaminated clothing that is not stuck to the skin to be removed, and for the first aider to avoid being contaminated too.
    3. Swallowed. The casualty is taken to medical attention immediately.
    4. Inhaled. The casualty is moved to fresh air at once, kept warm and at rest, and given medical attention as soon as possible. If breathing has stopped, a trained first aider gives artificial respiration and the emergency services are called.

    The label or the data sheet of the product is taken to the doctor. Pulmonary edema from exposure to nitric acid can appear late, so a casualty who has inhaled vapor is still examined even when feeling well.

    Handling and storage

    The manufacturer’s data sheet for one product of this class gives a storage temperature of 0 to 50 °C and names bases, strong bases above all, as materials to be kept away from the product. The descaler shelf is kept separate from strongly basic products, which are covered in Chapter 37 on liquid machine dishwashing detergent, and from all chlorine products. As long as the supplier has not confirmed the name of the acid, the NIOSH notes for nitric acid are applied as well: the jerry can is kept away from combustible materials such as cardboard and cleaning cloths, from alcohols, and from metallic powders.

    HSE gives general rules for cleaning substances in hospitality:

    • Substances are kept in their original labeled containers with lids, away from heat, sunlight, foodstuffs, and members of the public.
    • Cleaning substances are never transferred into food or drink containers.
    • Lifting and pouring from large containers is avoided; transfer is done with a siphon or a pump.
    • Staff are informed, trained, and supervised; issuing data sheets alone is not enough.

    Containers, stirrers, and funnels for this product are not made of metal. Small spills are handled according to Chapter 6 · Safety on chemicals in technician work, and empty containers according to Chapter 35 · Water & Water Treatment on B3 waste.

    Worked example

    The figures in the examples below are practice figures, unless their origin is stated. A relative density of 1.21 is used as the midpoint of the range on the data sheet, and the molar volume of a gas, 24.5 L/mol, applies at 25 °C and 1 atm.

    Example 1: mass of one jerry can. For a 20 L jerry can with a relative density of 1.19 to 1.23, the mass of the contents is 20×1.19=23.820 \times 1.19 = 23.8 kg to 20×1.23=24.620 \times 1.23 = 24.6 kg, heavier than 20 kg of water of the same volume. The contents are transferred with a pump, not by tipping the jerry can.

    Example 2: reading the dilution 1 : 1 to 5. If that figure is read as 1 part product plus 1 to 5 parts water, the fraction of product in the use solution is 1/(1+1)=0.51/(1+1) = 0.5 to 1/(1+5)=0.1671/(1+5) = 0.167. For 12 L of use solution, 12×0.5=612 \times 0.5 = 6 L of product is needed at 1 : 1, or 12/6=212/6 = 2 L of product and 10 L of water at 1 : 5. The data sheet does not say which ratio is for which machine, so what is used is the figure on the label and in the manual.

    Example 3: pH of the use solution. If the acid is fully ionized, diluting ff times raises the pH by log⁡f\log f. At 1 : 1 the rise is log⁡2=0.30\log 2 = 0.30, and at 1 : 5 the rise is log⁡6=0.78\log 6 = 0.78, so a pH of 1 to 2 becomes at most 1.78 to 2.78. Even the most dilute use solution is still around the pH 2.5 limit in the NIOSH table, so the personal protective equipment for the use solution is the same as for the concentrate.

    Example 4: whether the concentration and the pH agree. If the composition table is taken at face value with its lowest concentration of 10 percent, one liter of product has a mass of 1.21×1,000=1,2101.21 \times 1{,}000 = 1{,}210 g and holds 0.10×1,210=1210.10 \times 1{,}210 = 121 g of nitric acid. With a molecular weight of 63.02, the concentration is 121/63.02=1.92121/63.02 = 1.92 mol/L. A strong acid is fully ionized, so the calculated pH is −log⁡1.92=−0.28-\log 1.92 = -0.28, below zero, whereas pH 1 on the data sheet corresponds to 0.1 mol/L, which is 1.92/0.1=19.21.92/0.1 = 19.2 times more dilute. This calculation is rough because a solution that concentrated is not ideal, but the gap is too large to ignore. This result does not show which acid is in the jerry can, only that the concentration and the pH cannot both be correct for a strong acid. That is one more reason to ask the supplier.

    Example 5: scale that can be dissolved. Ten liters of use solution holding 0.50 mol of hydrogen ions per liter contains 10×0.50=5.010 \times 0.50 = 5.0 mol of hydrogen ions. The calcium carbonate that can react is at most 5.0/2=2.55.0/2 = 2.5 mol, which is 2.5×100.09=2502.5 \times 100.09 = 250 g, and the carbon dioxide gas is 2.5×24.5=612.5 \times 24.5 = 61 L. A quarter of a kilogram of scale uses up all of that acid and releases tens of liters of gas.

    Example 6: chlorine left in the tank. A 40 L wash tank still holds a solution with available chlorine of 100 mg/L when descaler is poured in. The chlorine released is at most 40×100=4,00040 \times 100 = 4{,}000 mg or 4.0 g, which is 4.0/70.90=0.05644.0/70.90 = 0.0564 mol and 0.0564×24.5=1.380.0564 \times 24.5 = 1.38 L of gas. A dishwashing room measuring 4 m by 3 m by 2.8 m has a volume of 33.6 m³ or 33,600 L, so the level is 1.38/33,600×106=411.38/33{,}600 \times 10^{6} = 41 ppm if all of it is released and evenly mixed, which is 41 times the PSD for chlorine. This is an upper bound, but one fortieth of it alone already equals the PSD.

    Stop conditions

    1. A sharp odor like bleach is noticed, or the eyes and throat sting, while descaler is in use: stop work and clear the room and the surrounding rooms. Do not re-enter only because the odor has gone. The supervisor calls the building emergency response team or the fire department, and anyone short of breath is taken to the emergency services.
    2. The dispenser for chlorinated detergent or sanitizer is still on, the tank has not been drained, or the buckets and measuring jugs are unlabeled: do not pour in descaler. The kitchen supervisor makes sure that dosing has stopped.
    3. The safety data sheet is absent, is past its validity date, or gives an acid name and concentration that differ between sections: the product is not used until the supervisor has a written explanation from the supplier.
    4. The material of the machine or equipment is unknown, or parts made of aluminum, galvanized steel, copper, or brass would be exposed: do not use descaler. The supervisor contacts the machine manufacturer.
    5. Bubbles keep coming from metal after the scale is gone, or brown fumes appear: stop, drain, and rinse. The machine is examined by the manufacturer’s technician before it is used again.
    6. The scale is in the boiler, the booster, the water pipes, or a part that can only be reached by dismantling the machine, or a leak appears after the scale comes off: do not do the work yourself. That work belongs to the machine manufacturer’s technician.
    7. A splash gets into the eyes, the skin feels burned, the product is swallowed, or someone is short of breath after inhaling vapor: give first aid and take the casualty to a doctor or the emergency services.
    8. A spill is larger than the local spill kit can handle, or a spill has reached a chlorine product: clear the room and hand over to trained personnel or the emergency response team.
    9. The dishwashing room ventilation is dead: postpone the work until a building technician restores the ventilation.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    A pH of 1 to 2 is enough to know what is in it.

    Why is it wrong?

    pH only states the hydrogen ion concentration. A dilute strong acid and a concentrated weak acid can have the same pH, although they behave differently toward metals and other materials. The name of the acid is established from the data sheet and the supplier.

    Common misconception

    It has been diluted 1 to 5, so no protection is needed.

    Why is it wrong?

    A sixfold dilution raises the pH by less than one unit, so the use solution is still very acidic.

    Common misconception

    The machine is stainless steel, so it withstands any acid.

    Why is it wrong?

    Stainless steel is protected only by a thin oxide layer, and inside a machine there can be brass, galvanized steel, and aluminum. What decides is the machine manual.

    Common misconception

    The longer it soaks, the cleaner it gets.

    Why is it wrong?

    Once the scale is gone, the remaining acid meets only metal and seals. Machine manuals forbid leaving the agent in for hours.

    Common misconception

    If the chlorine odor has gone, the dishwashing room is safe.

    Why is it wrong?

    The odor of chlorine is usually not detectable until above a level that already irritates. A room is declared safe by authorized personnel after sufficient air exchange.

    Chapter 9 · Dishwashing on dishwasher water quality, softeners, scale, and descaling contains the procedure that uses this product. Chapter 25 on chemical reactivity and incompatibility contains the segregation of materials and the chlorine gas calculation. Other acids for scale are covered in Chapter 30 on acid bathroom cleaners and Chapter 31 on rust, scale, and cement residue removers.

    Exercises and worked solutions

    Try to answer first, then open the worked solution.

    1. A 10 L jerry can holds a product with a relative density of 1.21. What is the mass of its contents, and how much does it differ from 10 L of water?

      Check my answer
      See the worked solution

      The mass of the contents is 10×1.21=12.110 \times 1.21 = 12.1 kg, whereas 10 L of water has a mass of 10 kg, so the difference is 2.1 kg. The lifting load is calculated from the relative density, not from the volume of the jerry can alone.

    2. The label of a product asks for 1 part product plus 3 parts water. How many liters of product are needed for 20 L of use solution, and how much does the pH rise if the acid is fully ionized?

      Check my answer
      See the worked solution

      The fraction of product is 1/(1+3)=0.251/(1+3) = 0.25, so 20×0.25=520 \times 0.25 = 5 L of product and 15 L of water are needed. A dilution of 4 times raises the pH by log⁡4=0.60\log 4 = 0.60, so the use solution is still very acidic.

    3. The data sheet of a descaler lists one acid in the composition table and another acid in the transport section. A staff member says both are acids, so it makes no difference. What is your response?

      Check my answer
      See the worked solution

      The two behave differently: nitric acid is a strong oxidizing agent that is incompatible with combustible materials and alcohols, whereas phosphoric acid releases hydrogen when it meets metal. A document that does not agree with itself cannot be the basis for choosing a storage place, so the product is held back until the supplier gives a written explanation.

    4. A 30 L tank is drained after the scale is gone and is left with 1.5 L of solution at pH 1.5. What is the pH after two fills and drains, if the acid is fully ionized?

      Check my answer
      See the worked solution

      Each fill dilutes 30/1.5=2030/1.5 = 20 times and raises the pH by log⁡20=1.30\log 20 = 1.30. After two fills, the pH is 1.5+2×1.30=4.11.5 + 2 \times 1.30 = 4.1, still acidic, so rinsing continues according to the manual.

    5. A descaler spill on the dishwashing room floor is about to be mopped up with a chlorinated sanitizer solution. What is wrong?

      Check my answer
      See the worked solution

      A chlorinated sanitizer that meets acid releases chlorine gas, just like the bleach and the acid cleaner in the opening case. The acid spill is handled with the spill kit according to the procedure, and the sanitizer is used in a separate job whose sequence is decided by the supervisor.

    6. After the scale in the tank is gone, fine bubbles still rise from a metal joint at the bottom of the tank. What does that mean?

      Check my answer
      See the worked solution

      The fizzing from scale stops when the scale is gone, so those bubbles come from metal reacting with the acid. The work is stopped, the tank is drained and rinsed, and the joint is examined by the manufacturer’s technician.

    References

    External sources

    • Epidemiologic Notes and Reports Chlorine Gas Toxicity from Mixture of Bleach with Other Cleaning Products -- Californiacdc.gov
    • NIOSH Pocket Guide to Chemical Hazardscdc.gov
    • Safe use of cleaning substances in the hospitality industryhse.gov.uk
    • Basic advice on first aid at workhse.gov.uk
    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
    • Chemistry 2eopenstax.org
    • UFC 3-240-13FN Industrial Water Treatment Operation and Maintenancewbdg.org
    • Cleaning National Parks: Using Environmentally Preferable Janitorial Products at Yellowstone and Grand Teton National Parksepa.gov
    • Disinfectants in the food and drink industryhse.gov.uk

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Descalers for dishwashers and kitchen equipment: strong mineral acid and pH 1 to 2, limescale, machine materials sensitive to acid, rinsing, the ban on mixing with chlorine, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/penghilang-kerak-mesin-pencuci-piring-dan-peralatan-dapur-asam-mineral-kuat-dan-ph-1-sampai-2-kerak-kapur-bahan-mesin-yang-peka-asam-pembilasan-larangan-mencampur-dengan-klor-serta-penanganan-dan-penyimpanan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A 10 L jerry can holds a product with a relative density of 1.21. What is the mass of its contents, and how much does it differ from 10 L of water?

    2

    The label of a product asks for 1 part product plus 3 parts water. How many liters of product are needed for 20 L of use solution, and how much does the pH rise if the acid is fully ionized?

    3

    The data sheet of a descaler lists one acid in the composition table and another acid in the transport section. A staff member says both are acids, so it makes no difference. What is your response?

    Self-assessment progress0%

    Nearby chapters