By Kurnia · Published November 15, 2026 · Version 1 · 20 min read
Dishwasher rinse additives
sodium xylene sulfonate and surfactant, acidic pH, wetting and spot-free drying, dosing through a dispenser, and handling and storage
Glasses that come out of a dishwasher covered in water droplets dry with spots, and the cause is often an empty rinse additive jerry can. This chapter covers rinse additives from the side of their chemistry: sodium xylene sulfonate at 5 to 10 percent and surfactant at 1 to 5 percent according to three manufacturer’s safety data sheets for products of this class, an acidic pH that differs from 2 to 6 between one data sheet and another, surface tension and wetting, why a thin sheet of water dries with fewer spots than droplets do, what a rinse additive cannot do, the class eye irritation category 2A, first aid, and handling and storage. Dosing rates and dispenser settings are not given. Setting the dispenser, improving water quality, and medical treatment are stated as work for other parties.
Glasses from the door-type dishwasher in a hotel restaurant came out covered in water droplets, and once dry every droplet left a whitish spot. For three days the staff wiped the glasses one by one before they went to the tables. The technician who was called found nothing wrong with the machine. The rinse additive jerry can beside the machine was already empty, and the foot filter of its suction tube was hanging in the air. The dispenser pump still turned at every rinse, but nothing was being pumped.
Water has a high surface tension, so rinse water readily gathers into droplets on a surface that is hard to wet. Every droplet that dries leaves behind the salts dissolved in it. A rinse additive lowers the surface tension of the rinse water so that the water spreads into a thin sheet and runs off. Compared with the corrosive machine detergent, this product is far less hazardous, but its data sheet still lists one hazard class and an acidic pH. Workers need to know what is in that jerry can, what it can and cannot do, and why this product must not be swapped with the two other jerry cans.
Scope
This chapter covers one class of product, namely liquid rinse additives for commercial dishwashers that are dosed by a dispenser: their contents and pH, how they act on the rinse water, the limits of what they can do, their hazards to eyes and skin, first aid, and handling and storage. The product data come from three manufacturer’s safety data sheets for products of this class. Other products may differ, so what applies is the label and the safety data sheet of the product in use.
This chapter is study material, not a work instruction. Dosing rates, concentrations in the rinse water, and dispenser settings are not given; all of them come from the chemical supplier, the product label, and the dispenser manual. How the dispenser doses, how it is set, and how its pump is maintained are in Chapter 7 · Chemical Dispensing on rinse aid dosing, maintenance, and troubleshooting of dishwasher dispensers, and its injection point is in Chapter 4 · Chemical Dispensing on dishwasher dispensers. Spots that come from water quality are covered in Chapter 9 · Dishwashing on dishwasher water quality, softeners, scale, and descaling.
Surfactants are covered in Chapter 21 on surfactants, colloids, and emulsions, the pH scale in Chapter 15 on advanced acids and bases, and how to check a data sheet in Chapter 26 on reading safety data sheets for cleaning products. The two other jerry cans beside the machine are covered in Chapter 37 on liquid machine dishwashing detergent and Chapter 39 on descalers for dishwashers and kitchen equipment.
Work outside the authority of dishwashing staff: setting the dose and repairing the dispenser, improving water quality, handling large spills or spills mixed with another product, and giving treatment other than first aid. The dispenser belongs to the dispenser technician or the chemical supplier, water quality belongs to the water treatment technician, large spills belong to trained personnel, and casualties are handled by a doctor or the emergency services.
What the product contains according to three data sheets
A rinse additive is a chemical injected into the final rinse water of a dishwasher so that the rinse water forms a thin sheet that runs evenly off the surface. Chapter 7 · Chemical Dispensing calls the same material a rinse aid.
Three manufacturer’s safety data sheets for products of this class give the same composition. The first ingredient is sodium xylene sulfonate with CAS number 1300-72-7 at 5 to 10 percent. The second ingredient is written only as surfactant, at 1 to 5 percent, with no chemical name and no CAS number because the manufacturer keeps it confidential. All three are liquids for industrial and professional use, are dosed by automatic setting through a dispenser, and carry the class eye irritation category 2A. What differs is the pH, the relative density, and the dates:
| Data sheet | pH of the 100 percent product | Relative density | Issued | Valid until |
|---|---|---|---|---|
| First | 4.0 to 5.0 | 0.990 to 1.010 | February 22, 2023 | February 21, 2028 |
| Second | 2 to 4 | 0.980 to 1.010 | February 22, 2023 | February 21, 2028 |
| Third | 4.0 to 6.0 | 0.995 to 1.010 | February 22, 2024 | February 21, 2027 |
Two things can be read from those data. The listed ingredients add up to only 6 to 15 percent of the product, and the rest is not itemized (Example 1). The data sheets also do not name the ingredient that makes the product acidic and do not explain the role of each ingredient. For that reason the pH of a rinse additive cannot be guessed from its composition; the pH is read from the data sheet of the product in use.
Sodium xylene sulfonate and surfactant
A surfactant is a compound whose molecule has a nonpolar part and a part that is attracted to water, so the molecules gather at the boundary between water and another material. Synthetic detergents, for example, have a nonpolar hydrocarbon chain such as a 12-carbon chain, and an ionic group such as a sulfate or a sulfonate. The nonpolar part is attracted to oil and dirt, and the ionic end is attracted to water. The classes and properties of surfactants are covered in Chapter 21.
Sodium xylene sulfonate is the sodium salt of dimethylbenzenesulfonic acid. The Safer Chemical Ingredients List of the EPA, the United States environmental protection agency, includes it with CAS number 1300-72-7 in the functional class surfactants, marked with a green circle. That mark means the chemical has been verified to be of low concern based on experimental and modeled data. Going by its name, this molecule has a sulfonate group like a synthetic detergent, but its nonpolar part is only one benzene ring with two methyl groups, far shorter than a 12-carbon chain.
Two notes keep that list from being read too broadly. The EPA assessment applies to the ingredient, not to the finished product, and the EPA states that using chemicals from the list does not entitle a product manufacturer to make claims related to the EPA. The second ingredient on the data sheets is unnamed, so its type and properties can only be asked of the supplier.
Wetting: from water droplets to a sheet of water
Surface tension is the energy required to increase the surface area of a liquid. This property comes from cohesive forces, which are the forces of attraction between molecules of the same liquid. Molecules at the surface are pulled only from the inside, so the liquid contracts to the shape with the smallest surface area, and a small drop comes close to a sphere. Among common liquids, water has a distinctly high surface tension, 71.99 mN/m at 25 °C, because the hydrogen bonding between its molecules is strong. Ethanol has only 21.97 mN/m.
An adhesive force is the force of attraction between the molecules of a liquid and the molecules of the surface it touches. If adhesion is weak compared with cohesion, water does not wet that surface and forms drops; this happens on waxed surfaces and many plastics, for example polyethylene. If adhesion is stronger, water spreads out; this happens on glass. Tableware lies between those two cases, depending on the material and on how clean the surface is.
Surface tension can be lowered. In 1891 Agnes Pockels showed that contaminants on the surface of water significantly reduce its surface tension. The surfactant in a rinse additive works that way: its molecules gather at the surface of the rinse water and weaken the pull that makes water bead up. The rinse water then spreads into a thin sheet that runs down off plates and glasses. Chapter 7 · Chemical Dispensing calls that result sheeting, and the technician judges it by looking at the ware that comes out of the machine.
A thin sheet also dries faster. For the same amount of water, a sheet has a far larger surface area than droplets, and evaporation takes place at the surface (Example 6). Plastic containers remain harder to wet than glass and ceramic, so the result on plastic is judged separately.
Spots: what a water droplet leaves behind
Rinse water is not pure water. It carries dissolved salts, mainly hardness salts, as covered in Chapter 16 on solubility and precipitation. When a droplet of water evaporates, the water goes and the salts stay where the droplet was. The mass left behind follows
where is the mass of solids left behind in mg, is the dissolved solids concentration in mg/L, and is the volume of water that dries on that surface in L. This formula assumes that all the dissolved solids are left behind and none runs off.
The formula shows two ways to reduce spots. A rinse additive makes smaller: less water stays on the surface, and what remains is spread thin, not collected at a few points (Example 4). A rinse additive does not change . If the salt content of the rinse water is high, spots still appear even when sheeting is good, and the remedy lies in water quality in Chapter 9 · Dishwashing.
A rinse additive is not a cleaner either. Food residue, fat, and detergent residue that are still attached are a matter for the wash stage, which is covered in Chapter 1 · Dishwashing on wash cycles, dosing, rinsing, sanitizing, and dispensers.
Acidic pH: what a range of 2 to 6 means
The pH scale is logarithmic:
with the hydronium ion concentration in mol/L. At 25 °C a neutral solution has pH 7, and for every drop of one pH unit the hydronium ion concentration rises 10 times. All three data sheets give an acidic pH, but the ranges are far apart: 2 to 4, 4.0 to 5.0, and 4.0 to 6.0. A product at pH 2 contains 10,000 times more hydronium ions than a product at pH 6 (Example 2). Two jerry cans that are both labeled rinse additive can differ greatly in acidity.
Two practical consequences follow from that acidity. The first concerns mixing. HSE, the British occupational safety authority, writes that products containing bleach mixed with acidic toilet cleaners or ammonia give off harmful gases, and gives one short rule: never mix cleaning substances. A rinse additive is acidic too, so it must not meet chlorine products, which are covered in Chapter 41 on concentrated sodium hypochlorite and chlorinated sanitizing powder in the kitchen, and it must not meet the strongly basic detergent in Chapter 37.
The second concerns a mistaken expectation. The data sheets state the use of this product as a rinse additive. This product enters the rinse water in a very small amount (Example 3), and its use is not to dissolve scale. Scale in the machine is dealt with by the method in Chapter 9 · Dishwashing and the material in Chapter 39.
Health hazards: eye irritation category 2A
All three data sheets classify the product as sold as eye irritation category 2A. In the global classification system as summarized by the EPA in 2004, category 2A means effects on the cornea, iris, or conjunctiva that fully reverse within 21 days, with the signal word warning and the exclamation mark pictogram. Category 1, the class of the machine detergent in Chapter 37, means effects that are not expected to reverse or that have not fully reversed within 21 days, with the signal word danger and the corrosion pictogram. The gap between those two classes is large, but even in category 2A the eye may need up to 21 days to recover.
HSE includes rinse aids in its list of hazardous cleaning substances in hospitality, together with dishwasher detergents, and names splashes to the skin and eyes while a substance is being poured from one container into another as a risk. Its guidance for workers:
- The protective clothing provided is always worn when handling cleaning substances, especially concentrates.
- Eye protection suitable for splash risks, for example goggles or a visor, is worn if there is any chance of splashing.
- Rubber gloves are checked for holes, tears, and thin patches, and replaced if faulty.
- Irritation or any other reaction to a substance is reported to the supervisor immediately.
The skin of dishwashing staff also faces wet work. HSE notes work-related dermatitis as one of the main causes of ill health for catering staff, recommends appropriate gloves for all cleaning activities, and asks for hands to be checked regularly for the first signs, namely itchy, dry, or red skin. Dermatitis is covered in Chapter 41 · Biology & Microbiology on skin and chemicals.
If the data sheet of a product classed as an eye irritant states that eye protection is not required, or carries no signal word, its content is checked by the method in Chapter 26 and the supplier is asked.
First aid
First aid follows the workplace procedure. HSE guidance for cleaning substances and chemical injuries:
- Eyes. The eye is flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then the casualty is sent to hospital.
- Skin. Splashes on the skin are washed away with plenty of water. If irritation persists, the casualty seeks medical advice and tells the employer.
- Swallowed or inhaled. The casualty contacts a doctor or the emergency services, and the label or the product’s data sheet is taken along.
Where tap water is not available near the machine, HSE asks for at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers to be provided.
Dosing through a dispenser
The three data sheets contain no dosing figure; all that is written is automatic setting through a dispenser. For that reason this chapter gives no dosing rate. The target concentration comes from the chemical supplier, and the formula and the way to set it are in Chapter 7 · Chemical Dispensing.
From the side of the chemistry, workers need to understand three things.
An empty jerry can may give no sign. The pump keeps turning even when the suction tube is drawing air, as in the opening case. The first sign is water droplets on the glasses, and the first check is the contents of the jerry can and the position of the foot filter, not the dispenser settings.
The tubes must not be swapped. Jerry cans of rinse additive, detergent, and descaler can be similar in size and color. HSE asks for every container to be clearly marked with its contents. If the rinse tube goes into the detergent jerry can, the final rinse sprays sodium hydroxide solution onto ware that is already clean. If it goes into the descaler jerry can, what is sprayed is an acid solution. The squeeze tube for rinse aid may also be made of a different material from the tube for detergent, as noted in Chapter 4 · Chemical Dispensing.
More is not better. A rinse additive is the last material to touch the ware before it dries, and there is no rinse after it. The amount follows the supplier’s target, and jerry can consumption that departs far from the calculation is a sign of a dispenser fault (Example 5).
Handling and storage
The three data sheets give a storage temperature of 0 to 50 °C. HSE gives guidance on storing and handling cleaning substances in hospitality:
- Substances are kept in their original labeled containers, with lids. Cleaning substances are never transferred into food or drink containers.
- The storage place is away from heat, sunlight, foodstuffs, and members of the public, especially children. The manufacturer’s storage instructions are checked because some products need to be stored separately.
- Pouring from bulk containers is avoided; handling is minimized by using pumps or siphons.
- Spills on floors or work surfaces are cleaned up immediately.
A jerry can of acidic rinse additive is stored apart from chlorine products and from strongly basic detergent, as covered in Chapter 25 on chemical reactivity and incompatibility. Leftover product is not poured into another jerry can, and the empty jerry can is handled according to the product label. Small spills are handled according to Chapter 6 · Safety on chemicals in technician work.
Worked example
The figures in the examples below are practice figures, unless their origin is stated. A relative density of 1.000 is used as the midpoint of the range on the first data sheet, so one milliliter of product has a mass of 1.000 g.
Example 1: listed ingredients per liter. One liter of product has a mass of 1,000 g. The sodium xylene sulfonate is g to g, and the surfactant is g to g. The listed ingredients total g to g, that is, 6 to 15 percent. The part that is not itemized is to percent.
Example 2: the difference in acidity. At pH 2, the hydronium ion concentration is mol/L, and at pH 6 it is mol/L. The ratio is , that is, 10,000 times. Even within one data sheet the difference is real: a range of 4.0 to 5.0 means a difference of times.
Example 3: concentration in the rinse water. Chapter 7 · Chemical Dispensing calculates one factory setting as 0.287 mL of rinse aid per liter of rinse water; this example uses a practice concentration of 0.3 mL/L. One liter of rinse water holds g of product, that is, 300 mg. The sodium xylene sulfonate is mg to mg per liter, and the surfactant is mg to mg per liter. The product is diluted times.
Example 4: spots from droplets and from a sheet. The rinse water has a dissolved solids concentration of 250 mg/L. Without rinse additive, 1.0 mL of water is left as droplets on one glass, so the solids left behind are mg, collected at a few points. With good sheeting, 0.10 mL is left, so the solids are mg and spread thin. The solids fall times, while the salt content of the water does not change.
Example 5: daily consumption and jerry can life. A machine washes 300 racks a day with 2.9 L of rinse water per rack. At 0.3 mL/L, consumption is mL a day, so a 5 L jerry can lasts days. If that jerry can is empty in 6 days, consumption is mL a day, that is, times the calculation. A gap that large is checked by the dispenser technician according to Chapter 7 · Chemical Dispensing, not dealt with by changing the jerry can more often.
Example 6: surface area of droplets and of a sheet. One milliliter of water is left as 20 hemispherical droplets of 0.05 cm³ each. From , the radius is cm, and the curved area of each droplet is cm². The total area is cm². If 0.10 mL of water spreads evenly over a glass with an area of 300 cm², the sheet thickness is cm, that is, 3.3 micrometers, and its surface area is 300 cm². The area per milliliter of water rises from 10.4 to cm², that is, times. This model is rough, but it shows why a thin sheet dries far faster than droplets.
Stop conditions
- Product gets in the eyes: stop work and flush the eye with water for at least 10 minutes. The casualty is sent to hospital.
- Product is swallowed, or skin irritation or breathing complaints persist after contact with the product: the casualty contacts a doctor or the emergency services, and the supervisor is told.
- The jerry can has no label, the label does not match the marking on the tube, or the safety data sheet is missing or past its validity date: do not connect that jerry can. The supervisor asks the supplier for an explanation.
- The rinse tube turns out to be connected to the detergent or descaler jerry can: stop the machine and do not use the ware that has already been rinsed. The dispenser technician flushes the line and checks the squeeze tube, and the kitchen supervisor decides on rewashing.
- Rinse additive meets a chlorine product, or a sharp odor like bleach is noticed: leave the area and clear the surrounding rooms. The supervisor calls trained personnel or the building emergency response team.
- A spill is larger than the local spill kit can handle, or is mixed with another product: hand it over to trained personnel.
- Water droplets or spots persist even though the jerry can has product in it and the tube is filled, or the jerry can empties much faster or much more slowly than calculated: the operator does not change the dispenser settings. The dispenser technician checks it according to Chapter 7 · Chemical Dispensing, and water quality is checked by the water treatment technician according to Chapter 9 · Dishwashing.
- The skin of a worker’s hands is itchy, dry, red, or cracked: report it to the supervisor. Examination and treatment are a matter for a doctor.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
A rinse additive is soap, so the more the cleaner.
Why is it wrong?
This product does not clean. Its use is to make the rinse water spread and run off, and the amount follows the supplier’s target.
Common misconception
A rinse additive removes all spots.
Why is it wrong?
A rinse additive reduces the water left behind, not the salts in that water. Spots from rinse water with a high salt content are resolved through water quality.
Common misconception
Its pH is acidic, so it also cleans scale from the machine.
Why is it wrong?
This product enters the rinse water in a very small amount, and its use on the data sheet is as a rinse additive. Scale is dealt with by its own method and material.
Common misconception
All rinse additives are equally acidic.
Why is it wrong?
Three data sheets for products of this class give a pH from 2 to 6, a difference of up to 10,000 times in hydronium ion concentration.
Common misconception
Its class is only eye irritation, so eye protection is not needed.
Why is it wrong?
Category 2A means effects on the eye that may need up to 21 days to recover. Eye protection is worn if there is any chance of splashing, for example when the jerry can is changed.
Links to other chapters
Chapter 7 · Chemical Dispensing on rinse aid dosing, maintenance, and troubleshooting of dishwasher dispensers gives the way to dose this product and check its dispenser. Chapter 9 · Dishwashing on dishwasher water quality, softeners, scale, and descaling covers the source of spots that a rinse additive cannot deal with. Chapter 37 on liquid machine dishwashing detergent and Chapter 39 on descalers for dishwashers and kitchen equipment cover the two jerry cans that must not be swapped with this product.
Exercises and worked solutions
The figures in the problems are for practice.
Try to answer first, then open the worked solution.
A 10 L jerry can holds rinse additive with a relative density of 0.995. How many kilograms of sodium xylene sulfonate does it hold at 5 percent and at 10 percent?
Check my answer
See the worked solution
The mass of product is kg. The sodium xylene sulfonate is kg to kg, so about half a kilogram to one kilogram. The concentration range on a data sheet means the actual content can differ by a factor of two.
The data sheet of the old product gives pH 4, and the data sheet of the replacement product gives pH 2. By how many times does the hydronium ion concentration differ, and what does that mean for workers?
Check my answer
See the worked solution
A difference of 2 pH units means the hydronium ion concentration differs by times. The replacement product is far more acidic even though its name is the same, so its data sheet is read again and its separation from chlorine products is checked again.
Glasses come out of the machine with water droplets. The rinse additive pump can be heard turning, but the level in the jerry can has not dropped for a week. What is checked first, and what does the operator not do?
Check my answer
See the worked solution
What is checked first is the contents of the jerry can and the position of the foot filter, because the pump keeps turning even when the tube is drawing air. The operator does not change the dispenser settings; if the tube is filled but the product still does not go down, the dispenser technician checks it according to Chapter 7 · Chemical Dispensing.
A machine washes 150 racks a day with 2.9 L of rinse water per rack at a concentration of 0.3 mL/L. What is the daily consumption, and how many days does a 5 L jerry can last?
Check my answer
See the worked solution
Consumption is mL a day, so a 5 L jerry can lasts days. This figure serves as a benchmark: a jerry can that empties much faster or much more slowly indicates that the dispenser needs checking.
A worker wants to pour leftover rinse additive into a nearly empty detergent jerry can so that it is not wasted. What is wrong?
Check my answer
See the worked solution
A rinse additive is acidic and machine detergent is a strong base, so the two react and give off heat, and the contents of the detergent jerry can no longer match its label. Cleaning substances are never mixed, and leftover product is handled according to the label.
The rinse water has a dissolved solids concentration of 400 mg/L. How much solid is left behind if 0.8 mL of water dries on a plate, and if only 0.1 mL does? What does not change?
Check my answer
See the worked solution
The solids are mg for 0.8 mL and mg for 0.1 mL, so they fall times. The salt content of the water stays at 400 mg/L, so the remaining spots can only be reduced through water quality.
References
External sources
- Chemistry 2eopenstax.org
- Safer Chemical Ingredients Listepa.gov
- Chemical Hazard Classification and Labeling: Comparison of OPP Requirements and the GHSepa.gov
- Safe use of cleaning substances in the hospitality industryhse.gov.uk
- Basic advice on first aid at workhse.gov.uk
- Skin problems in catering businesseshse.gov.uk
Revision history
| Date | Version | Change |
|---|---|---|
| November 15, 2026 | 1 | First published |
How to cite
Kurnia (2026). Dishwasher rinse additives: sodium xylene sulfonate and surfactant, acidic pH, wetting and spot-free drying, dosing through a dispenser, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/aditif-pembilas-mesin-pencuci-piring-natrium-xilena-sulfonat-dan-surfaktan-ph-asam-pembasahan-dan-pengeringan-tanpa-bercak-takaran-lewat-dispenser-serta-penanganan-dan-penyimpanan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
A 10 L jerry can holds rinse additive with a relative density of 0.995. How many kilograms of sodium xylene sulfonate does it hold at 5 percent and at 10 percent?
The data sheet of the old product gives pH 4, and the data sheet of the replacement product gives pH 2. By how many times does the hydronium ion concentration differ, and what does that mean for workers?
Glasses come out of the machine with water droplets. The rinse additive pump can be heard turning, but the level in the jerry can has not dropped for a week. What is checked first, and what does the operator not do?
Nearby chapters
Reading order by shelf: Chemistry · Chapter 39.
Reading order by shelf: Chemistry · Chapter 37.