Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Chemistry · Chapter 42Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 19 min read

    Soaking powder for removing stains from tableware

    salt, sodium carbonate, surfactant, and a chlorine releaser, the 1.5 percent solution, tea and coffee stains, materials that must not be soaked, and handling and storage

    In health-care facilities in four states of the United States, 401 workers fell ill from disinfectants and sanitizers in six years; the eyes were affected most often, and only 15 percent of those handling the substances wore eye protection. This chapter covers soaking powder for removing stains from tableware from the side of the chemical itself: sodium chloride, sodium carbonate, a sulfonate surfactant, and sodium dichloroisocyanurate as a chlorine releaser according to the manufacturer’s safety data sheet for one product of this class, pH 11 to 12, the 1.5 percent use solution and the available chlorine in it, how tea and coffee stains are bleached, items that must not be soaked such as aluminum, silver, earthenware, and gold decoration, the ban on mixing with acids and ammonia, personal protective equipment, first aid, and handling and storage. Soaking time and water temperature are read from the label. Germ-killing power is not covered, and large spills and treating casualties are stated as the work of other parties.

    Section you’re reading: Chapter opening

    Between 2002 and 2007, surveillance programs in four states of the United States recorded 401 cases of work-related illness from antimicrobial substances such as disinfectants and sanitizers in health-care facilities, 268 of them in hospitals. More than half of the cases, namely 51 percent, happened through splashes, spills, or leaks. The eyes were the part of the body affected most often, in 55 percent of cases, and of the 265 people who were handling the substances only 15 percent wore eye protection. Sodium hypochlorite, the active ingredient of bleach, was recorded in 18 percent of cases.

    Stain-removing soaking powder in a dishwashing room works with a substance closely related to bleach, because the powder releases chlorine into the soaking water. Staff measure out the powder, stir, then put cups in and lift them out by hand, and every one of those steps can splash. The people who use it need to know what is in the powder, why its dose is 1.5 percent and not a handful, which items must not go into the tub, and why that tub must not meet acid.

    Scope

    This chapter covers one class of product, namely powder that is dissolved in water to soak stained tableware: the contents of the product, the 1.5 percent use solution, the roles of sodium carbonate, the surfactant, and the chlorine releaser, tea and coffee stains, materials that must not be soaked, the ban on mixing with acids and ammonia, health hazards, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of this class. What applies in the workplace is the label and the data sheet of the product actually in use.

    This chapter is learning material, not a work instruction. Soaking time, water temperature, and how often the solution is replaced are not stated on that data sheet and are not given here; all of them are read from the product label. Germ-killing power is not covered, because the data sheet calls this product a cleaning product. Sanitizing of equipment is in Chapter 7 · Biology & Microbiology on kitchen sanitation and critical control points, and how chlorine works as a disinfectant is in Chapter 4 · Biology & Microbiology on disinfectants and how they work.

    Surfactants are covered in Chapter 21 on surfactants, colloids, and emulsions, available chlorine in Chapter 17 on advanced redox, and hazardous mixtures in Chapter 25 on chemical reactivity and incompatibility. Hypochlorite solution and sanitizing powder are covered in Chapter 41 on concentrated sodium hypochlorite and chlorinated sanitizing powder, and the dishwasher cycle in Chapter 1 · Dishwashing on the washing cycle, dosing, rinsing, sanitation, and dispensers.

    Work outside the authority of dishwashing staff: deciding whether antique, silver-plated, or gold-decorated items may be soaked, repairing metal or decoration that is already damaged, handling a large spill or powder that has come into contact with acid, and giving treatment other than first aid. Decisions about items belong to the supervisor together with the tableware supplier, large spills belong to trained personnel or the emergency response team, and casualties are handled by a doctor or the emergency services.

    What the product contains: four ingredients and the 1.5 percent solution

    According to the manufacturer’s safety data sheet for one product of this class, the soaking powder is a white powder that is soluble in water, with a relative density of 0.869 to 0.873. Its 1 percent solution has a pH of 11 to 12, and its dilution information reads 1.5 percent. The recommended use is given as a cleaning product, and the product as sold is classified as eye irritation category 2. The data sheet was issued on February 22, 2024 and is valid until February 21, 2029, and lists the following four ingredients.

    IngredientCAS numberConcentration (percent)Class
    Sodium chloride7647-14-530 to 60table salt
    Sodium carbonate497-19-810 to 30base
    Sodium dodecylbenzene sulfonate25155-30-05 to 10sulfonate surfactant
    Sodium dichloroisocyanurate dihydrate51580-86-01 to 5chlorine releaser

    The data sheet does not state the role of each ingredient; the class column is filled in from the chemical nature of each substance. The four ranges also need not add up to 100 percent, and other ingredients that are not listed can be present (Example 6). How to read concentration ranges is covered in Chapter 26 on reading the safety data sheets of cleaning products.

    A use solution is the solution made from the product and water according to the dose, the one actually used for the work. The figure of 1.5 percent on the data sheet comes without a unit. If it is read as 1.5 grams of powder in every 100 mL of water, the dose is 15 grams per liter (Example 1). The dose that applies is still the one written on the label, with the measuring scoop or scale provided.

    Sodium carbonate and the surfactant: an alkaline solution that wets

    Sodium carbonate makes the solution basic. Carbonates are moderately strong bases, because the carbonate ion accepts a hydrogen ion from water and leaves a hydroxide ion:

    CO32−(aq)+H2O(l)⇌HCO3−(aq)+OH−(aq)\text{CO}_3^{2-}(aq) + \text{H}_2\text{O}(l) \rightleftharpoons \text{HCO}_3^-(aq) + \text{OH}^-(aq)

    For a carbonate solution at a concentration of CC mol/L, the hydroxide ion concentration xx satisfies

    Kb=KwKa2=x2C−x,pOH=−log⁡x,pH=14−pOHK_b = \frac{K_w}{K_{a2}} = \frac{x^2}{C - x}, \qquad \text{pOH} = -\log x, \qquad \text{pH} = 14 - \text{pOH}

    with Kw=1.0×10−14K_w = 1.0 \times 10^{-14} and Ka2=4.7×10−11K_{a2} = 4.7 \times 10^{-11}, the second ionization constant of carbonic acid, so that Kb=2.13×10−4K_b = 2.13 \times 10^{-4}. This formula applies at 25 °C, treats the solution as ideal, and ignores the other ingredients of the powder. Its result agrees with the pH on the data sheet (Example 3). A solution at pH 11 to 12 is alkaline, and how alkaline cleaners act on greasy soil is covered in Chapter 28 on mildly alkaline all-purpose cleaners.

    Sodium dodecylbenzene sulfonate is a surfactant. A detergent molecule has a nonpolar hydrocarbon chain, for example a chain of twelve carbons, and an ionic group such as a sulfonate. The hydrocarbon end is attracted to oil and dirt, whereas the ionic end is attracted to water, so the dirt is suspended and easily rinsed away. Unlike soap, detergents do not form insoluble calcium and magnesium compounds in hard water. The details are in Chapter 21 on surfactants, colloids, and emulsions.

    The chlorine releaser: from powder to hypochlorous acid

    Sodium dichloroisocyanurate, also called sodium dichloro-s-triazinetrione, is the sodium salt of a chlorinated triazine compound that is used as a source of free chlorine in the form of hypochlorous acid. According to WHO, this compound is widely used in swimming pools and the food industry as a stable source of chlorine. As soon as it enters water, the compound hydrolyzes rapidly and releases free chlorine, while part of the chlorine stays bound to the isocyanurate as a reservoir. If hypochlorous acid is consumed by reacting with organic material, that reservoir dissociates and releases fresh hypochlorous acid. CDC, the United States health agency, notes the same thing: only about half of the available chlorine from this compound is in the free form, and the rest is released as the free part is used up.

    Available chlorine is a measure of the oxidizing power of a chlorine compound, expressed as the equivalent mass of chlorine, as explained in Chapter 17 on advanced redox. The dihydrate form of sodium dichloroisocyanurate has an available chlorine of 55 to 56 percent of its mass. The available chlorine level in a use solution can be estimated with

    c=D×w×f×1,000c = D \times w \times f \times 1{,}000

    with cc the available chlorine (mg/L), DD the dose of powder (g/L), ww the mass fraction of chlorine releaser in the powder, and ff the fraction of available chlorine in that chlorine releaser. This formula gives the initial level of a fresh solution. That level falls while the solution is in use, because the chlorine is consumed by soil until it is gone.

    The properties of free chlorine apply to this solution as well. CDC notes that hypochlorite solutions are corrosive to metals at high concentrations, namely above 500 ppm, are inactivated by organic matter, bleach fabrics, and release toxic chlorine gas when mixed with ammonia or acid. A use solution at the stated dose is below 500 ppm, but an excessive dose can exceed it (Example 4).

    Tea and coffee stains: lifted or only bleached

    The brown stain inside a cup is coloring matter from the drink that is left on the surface. A guide to the care of ceramic collections from the National Park Service, the United States national parks agency, notes that beverage stains such as tea act as dyes. The soaking solution attacks that stain in two ways. The surfactant and the alkali wet and loosen the film that clings, whereas hypochlorous acid oxidizes colored substances to colorless ones, the same reaction as in the bleaching of cloth and wood pulp.

    Both ways have limits. Bleaching alters the color of a stain, but does not always lift the material. According to the same guide, in porous ceramics the stain remains inside the ceramic body and can come back. For that reason, items that have been soaked are still washed and rinsed as usual, and soaking does not replace washing. Chlorine is also consumed by food residue, so food residue is scraped off and rinsed away before items go into the tub, and the solution is replaced according to the label.

    Materials that must not be soaked

    The manufacturer’s data sheet for one product of this class names acids and metals as incompatible materials. Tableware includes many metals and decorations, so the contents of the tub are sorted first. The table below gives the reasons; what decides is still the product label and the instructions of the tableware maker.

    ItemWhat happensRule
    Aluminum, for example trays and teapotsaluminum reacts with bases and releases hydrogen gas, while the use solution is at pH 11 to 12not soaked, unless the label states that it is safe
    Silver and silver plateeven gloves processed with chlorine tarnish silver after a short period of contactnot soaked
    Carbon steel and iron, for example carbon steel kniveschloride ions, which are also found in table salt, greatly accelerate the deterioration of metals, iron in particularnot soaked
    Stainless steelchlorine is corrosive to metals at high concentrationsdose and soaking time do not exceed the label; rinsed thoroughly
    Earthenware, terracotta, and crazed glazeliquid enters through cracks in the glaze into the porous body; chlorine bleach damages that body and leaves salts if it is not rinsed out thoroughlynot soaked
    Gold decoration and painting over the glazethe gold layer is weakly adhered and fragile, and overglaze decoration wears off easilynot soaked; follow the maker’s instructions
    Hollow handlesliquid enters hollow parts that are difficult to rinse and drynot soaked
    Colored cleaning cloths and napkinschlorine bleaches fabricskept out of the tub

    The National Park Service guides were written for museum collections, so they show how those materials are damaged, not rules for hotel tableware. Items of unknown material are treated as sensitive items until their supplier answers.

    The ban on mixing with acids and ammonia

    The manufacturer’s data sheet for one product of this class warns that mixing the product with acids or ammonia can release chlorine gas. HSE, the British occupational safety authority, writes that chlorine-based disinfectants release toxic chlorine gas when in contact with acid, that hypochlorites form irritant nitrogen halide vapors in contact with amines such as quaternary ammonium compounds, and that incompatible chemicals are stored separately. The reactions are set out in Chapter 25 on chemical reactivity and incompatibility.

    In a kitchen, acid is found in descalers, which are covered in Chapter 39 on descalers for dishwashers and kitchen equipment, in rinse additives in Chapter 38 on dishwasher rinse additives, and in vinegar. Amines are found in the sanitizers in Chapter 40 on quaternary ammonium sanitizers for kitchen surfaces. Soaking powder and soaking solution are not poured into a tub, bucket, or drain that still holds those products, and measuring scoops are not shared between them.

    NIOSH, the United States occupational safety and health institute, records the symptoms of exposure to chlorine gas: burning of the eyes, nose, and mouth, watering eyes, cough, choking, chest pain, nausea, headache, up to pulmonary edema. NIOSH recommends a limit of 0.5 ppm for a 15-minute exposure and sets 10 ppm as the level that is immediately dangerous to life or health. The Indonesian threshold limit value for chlorine is covered in Chapter 39 on descalers for dishwashers and kitchen equipment.

    Health hazards, personal protective equipment, and first aid

    HSE classes hypochlorite and organic chlorine-releasing compounds as corrosive in their concentrated form and as eye and skin irritants when diluted. That is in line with the eye irritation classification on the data sheet and with the figures in the opening case. Skin that stays wet with an alkaline solution for a long time also becomes inflamed easily, as explained in Chapter 41 · Biology & Microbiology on the skin and chemicals. The HSE rules for this work:

    • Powder is always taken with a scoop, never with the hand.
    • Work with soak tanks carries a risk of splashes to the skin and eyes, and often requires an impermeable apron, gauntlets, and safety spectacles or a visor.
    • The working concentration does not exceed the manufacturer’s specification, because overdosing increases the risk to workers, is wasteful, and may damage equipment.
    • Rubber gloves are checked for holes and tears, and latex gloves are avoided.

    The report in the opening case closes with advice in the same direction: more emphasis on eye protection, and containers and pouring equipment designed so that they do not splash. First aid follows the label and the workplace procedure, with the following rules:

    1. Eyes. Loose powder is washed out with clean water. For chemicals, HSE asks for the eye to be flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then for the casualty to be sent to hospital.
    2. Skin. Splashes are washed away with plenty of water. If irritation persists, the casualty seeks medical advice and tells their employer.
    3. Swallowed. The casualty is taken to a doctor or the emergency services together with the product label.

    For a person who has inhaled chlorine gas, NIOSH asks for the casualty to be moved to fresh air at once, kept warm and at rest, and given medical attention as soon as possible. If breathing has stopped, a trained first aider gives artificial respiration and the emergency services are called.

    Handling and storage

    The manufacturer’s data sheet for one product of this class gives a storage temperature of minus 30 to 50 °C. Acids and metals, which it names as incompatible, decide the location and the container: the powder is not stored on the same shelf as descaler or rinse additive, and the soaking tub is not made of aluminum or of a metal the label does not name.

    HSE gives general rules for cleaning substances in hospitality:

    • Substances are kept in their original labeled containers with lids, away from heat, sunlight, and foodstuffs.
    • Cleaning substances are never transferred into food or drink containers.
    • The manufacturer’s storage instructions are checked, because some products need to be stored separately.
    • Staff are informed, trained, and supervised; issuing data sheets alone is not enough.

    The powder container is closed tightly after use and its measuring scoop is kept dry. The soaking tub is marked so that it is not mistaken for rinse water. Used solution is disposed of according to the label and the workplace procedure, not into a sink that still holds acid residue, and small spills are handled according to Chapter 6 · Safety on chemicals in technician work.

    Worked example

    The figures in the examples below are practice figures, unless their origin is stated. The 1.5 percent solution is read as 15 grams of powder per liter, the available chlorine of the chlorine releaser is taken as 55 percent, and the molar volume of a gas, 24.5 L/mol, applies at 25 °C and 1 atm.

    Example 1: powder for one tub. A tub holding 20 L of water needs 20×15=30020 \times 15 = 300 g of powder, and a 35 L tub needs 35×15=52535 \times 15 = 525 g. The powder is weighed or measured with the scoop from the supplier, because a handful has no size.

    Example 2: contents of each liter of use solution. Out of 15 g of powder per liter, sodium chloride amounts to 15×0.30=4.515 \times 0.30 = 4.5 g to 15×0.60=9.015 \times 0.60 = 9.0 g, sodium carbonate 15×0.10=1.515 \times 0.10 = 1.5 g to 15×0.30=4.515 \times 0.30 = 4.5 g, surfactant 15×0.05=0.7515 \times 0.05 = 0.75 g to 15×0.10=1.515 \times 0.10 = 1.5 g, and chlorine releaser 15×0.01=0.1515 \times 0.01 = 0.15 g to 15×0.05=0.7515 \times 0.05 = 0.75 g. The ingredient present in the smallest amount is the very one that decides the mixing hazard.

    Example 3: whether the pH fits the carbonate concentration. A 1 percent solution holds 10 g of powder per liter, so its sodium carbonate is 1.0 to 3.0 g/L. With a molar mass of 105.99 g/mol, C=1.0/105.99=0.00943C = 1.0/105.99 = 0.00943 mol/L to C=3.0/105.99=0.0283C = 3.0/105.99 = 0.0283 mol/L. For the lowest concentration, x=(−Kb+Kb2+4KbC)/2=0.00131x = (-K_b + \sqrt{K_b^2 + 4K_bC})/2 = 0.00131 mol/L, pOH =2.88= 2.88, and pH =14−2.88=11.12= 14 - 2.88 = 11.12. For the highest concentration, x=0.00235x = 0.00235 mol/L, pOH =2.63= 2.63, and pH =11.37= 11.37. Both results lie within the pH 11 to 12 range on the data sheet, so the carbonate concentration and the pH in that document agree with each other.

    Example 4: available chlorine in the use solution. At a dose of 15 g/L, c=15×0.01×0.55×1,000=82.5c = 15 \times 0.01 \times 0.55 \times 1{,}000 = 82.5 mg/L to c=15×0.05×0.55×1,000=412.5c = 15 \times 0.05 \times 0.55 \times 1{,}000 = 412.5 mg/L. Both are below 500 ppm. If the dose is doubled to 30 g/L, the upper bound is 30×0.05×0.55×1,000=82530 \times 0.05 \times 0.55 \times 1{,}000 = 825 mg/L, above the figure that CDC links with corrosion of metals. What certainly increases with an excessive dose is the risk to metals and to staff.

    Example 5: chlorine gas if the tub meets acid. A 20 L tub with available chlorine of 412.5 mg/L holds 20×412.5=8,25020 \times 412.5 = 8{,}250 mg or 8.25 g. If all of it is released as gas because acid is poured into the tub, the amount is 8.25/70.90=0.11648.25/70.90 = 0.1164 mol, which is 0.1164×24.5=2.850.1164 \times 24.5 = 2.85 L. In a dishwashing room measuring 4 m by 3 m by 2.8 m, which is 33.6 m³ or 33,600 L, the level is 2.85/33,600×106=852.85/33{,}600 \times 10^{6} = 85 ppm if evenly mixed. That figure is 8.5 times the 10 ppm level that NIOSH calls immediately dangerous. This is an upper bound, but one eighth of it alone already exceeds 10 ppm.

    Example 6: reading concentration ranges. The sum of the lower limits of the four ingredients is 30+10+5+1=4630 + 10 + 5 + 1 = 46 percent, and the sum of their upper limits is 60+30+10+5=10560 + 30 + 10 + 5 = 105 percent. The four ingredients cannot all be at their upper limits together, because the total exceeds 100. The part that is not listed is at most 100−46=54100 - 46 = 54 percent and at least zero. The ranges on a data sheet are not a recipe, so the calculations in Examples 2 to 5 are bounds, not exact contents.

    Stop conditions

    1. A sharp chlorine odor comes from the tub or the powder container, or the eyes and throat sting: stop work and clear the room. The supervisor calls the building emergency response team or the fire department, and anyone short of breath is taken to the emergency services.
    2. Descaler, rinse additive, vinegar, or an ammonia product is in the same tub, bucket, or drain, or its container is unlabeled: do not pour in soaking powder or soaking solution. The supervisor decides the work sequence and the containers to be used.
    3. An item is made of aluminum, silver, or earthenware, has gold decoration or a cracked glaze, or is of an unknown material: do not soak it. The supervisor contacts the tableware supplier.
    4. Metal is spotted or discolored, or decoration has faded, after soaking: stop, rinse, and set aside items of the same kind. Their replacement or repair is decided by the supervisor together with the supplier.
    5. The powder in its container is wet, caked, or smells sharply of chlorine: do not use it. The supervisor contacts the chemical supplier.
    6. The measuring scoop is missing or the label is unreadable: do not measure by guesswork. The supervisor provides a replacement measure and label.
    7. Powder or solution gets into the eyes, skin irritation does not subside, the product is swallowed, or someone is short of breath after inhaling gas: give first aid and take the casualty to a doctor or the emergency services.
    8. A large amount of powder is spilled, or a spill has come into contact with acid: clear the room and hand over to trained personnel or the emergency response team.
    9. The safety data sheet is absent, is past its validity date, or does not agree with the label: the product is not used until the supervisor has an explanation from the supplier.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    It is salt and soda, so it is as safe as kitchen ingredients.

    Why is it wrong?

    This powder also contains a chlorine releaser, its solution is at pH 11 to 12, and its data sheet classifies it as an eye irritant.

    Common misconception

    The more powder, the faster it cleans.

    Why is it wrong?

    A double dose can take the available chlorine past 500 ppm, the level that CDC links with corrosion of metals. The dose follows the label.

    Common misconception

    This soak sanitizes at the same time.

    Why is it wrong?

    The data sheet calls it a cleaning product, and the chlorine in the solution is consumed by soil. Sanitizing is a separate step with a set concentration and contact time.

    Common misconception

    The stain is gone, so the soil is gone.

    Why is it wrong?

    Bleaching alters the color of a stain and does not always lift the material. Items are still washed and rinsed after soaking.

    Common misconception

    All tableware can go into the tub.

    Why is it wrong?

    Aluminum, silver, carbon steel, earthenware, crazed glaze, and gold decoration can be damaged. Items of unknown material are not soaked until their supplier answers.

    Chapter 41 on concentrated sodium hypochlorite and chlorinated sanitizing powder covers more concentrated chlorine products, and Chapter 39 on descalers for dishwashers and kitchen equipment covers the acid that must not meet this powder. Chapter 4 · Biology & Microbiology on disinfectants and how they work explains chlorine and pH, and Chapter 26 on reading the safety data sheets of cleaning products gives the way to check the document.

    Exercises and worked solutions

    Try to answer first, then open the worked solution.

    1. A soaking tub holds 12 L of water. How many grams of powder are needed for a 1.5 percent solution, if percent is read as grams per 100 mL?

      Check my answer
      See the worked solution

      The dose is 15 g per liter, so 12×15=18012 \times 15 = 180 g of powder is needed. The powder is weighed or measured with the scoop, not estimated, because the dose sets the chlorine level in the tub.

    2. The powder of a product contains 3 percent chlorine releaser with an available chlorine of 55 percent. What is the available chlorine of a fresh solution at a dose of 15 g/L?

      Check my answer
      See the worked solution

      The available chlorine is 15×0.03×0.55×1,000=247.515 \times 0.03 \times 0.55 \times 1{,}000 = 247.5 mg/L. That figure is the initial level of a fresh solution; the level falls while the solution is in use because the chlorine is consumed by soil.

    3. A staff member adds twice the dose so that the cups whiten quickly. With the data of question 2, what is the available chlorine, and what is the consequence?

      Check my answer
      See the worked solution

      At 30 g/L the available chlorine is 30×0.03×0.55×1,000=49530 \times 0.03 \times 0.55 \times 1{,}000 = 495 mg/L, almost 500 ppm. The risk of metal corrosion and of irritation to staff rises, whereas the dose that applies is still the one written on the label.

    4. A staff member is about to soak an aluminum teapot and silver-plated spoons together with porcelain cups. What is your decision?

      Check my answer
      See the worked solution

      The aluminum teapot and the silver-plated spoons are not soaked. Aluminum reacts with a basic solution, and silver is tarnished by chlorine, whereas porcelain cups with an intact glaze and no gold decoration may be soaked according to the label.

    5. Leftover soaking solution is about to be poured into a sink that has just been used to dissolve descaler. What is wrong?

      Check my answer
      See the worked solution

      The acid residue in the sink will meet the chlorinated solution and can release chlorine gas. The sink is rinsed thoroughly first, and the two products are not emptied one after the other into the same sink without rinsing.

    6. After soaking, the cups look white. The staff member wants to put them straight on the shelf. What is missing?

      Check my answer
      See the worked solution

      The cups have not been washed and rinsed. Soaking bleaches the stain and leaves chlorinated alkaline solution on the surface, so the cups still go through the usual washing and rinsing before they are stored.

    References

    External sources

    • Acute Antimicrobial Pesticide-Related Illnesses Among Workers in Health-Care Facilities --- California, Louisiana, Michigan, and Texas, 2002--2007cdc.gov
    • Sodium Dichloroisocyanurate in Drinking-water: Background document for development of WHO Guidelines for Drinking-water Qualitycdn.who.int
    • Chemical Disinfectants, Guideline for Disinfection and Sterilization in Healthcare Facilities (2008)cdc.gov
    • Disinfectants in the food and drink industryhse.gov.uk
    • Safe use of cleaning substances in the hospitality industryhse.gov.uk
    • Basic advice on first aid at workhse.gov.uk
    • Chemistry 2eopenstax.org
    • National Park Service Conserve O Gramsnps.gov
    • NIOSH Pocket Guide to Chemical Hazardscdc.gov

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Soaking powder for removing stains from tableware: salt, sodium carbonate, surfactant, and a chlorine releaser, the 1.5 percent solution, tea and coffee stains, materials that must not be soaked, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/serbuk-perendam-penghilang-noda-peralatan-makan-garam-natrium-karbonat-surfaktan-dan-pelepas-klor-larutan-1-5-persen-noda-teh-dan-kopi-bahan-yang-tidak-boleh-direndam-serta-penanganan-dan-penyimpanan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated
    1

    A soaking tub holds 12 L of water. How many grams of powder are needed for a 1.5 percent solution, if percent is read as grams per 100 mL?

    2

    The powder of a product contains 3 percent chlorine releaser with an available chlorine of 55 percent. What is the available chlorine of a fresh solution at a dose of 15 g/L?

    3

    A staff member adds twice the dose so that the cups whiten quickly. With the data of question 2, what is the available chlorine, and what is the consequence?

    Self-assessment progress0%

    Nearby chapters