By Kurnia · Published November 15, 2026 · Version 1 · 21 min read
Mildly alkaline all-purpose cleaners
surfactants and active ingredients, pH 10 to 12, greasy soil, alkali-sensitive surfaces, rinsing, and handling and storage
The aluminum trim and the floor finish in front of a hospital ward pantry turn dull after a mildly alkaline all-purpose cleaner is diluted 1 : 5 and not rinsed off, even though its safety data sheet gives 1 : 20 to 1 : 50. This chapter covers all-purpose cleaners with a pH of 10 to 12: what that pH figure means in terms of hydroxide ion concentration, alkylbenzene sulfonates and the other ingredients listed on the data sheet, why alkaline conditions help release greasy soil, alkali-sensitive surfaces, dilution and rinsing, eye and skin protection, first aid, and handling and storage. The product data come from manufacturer safety data sheets that are still valid as of November 2026. Stripping floor finish, acid rinsing of stone, large spills, and health complaints are written as limits, with the party that takes over.
The cleaning team of a hospital replaced the neutral cleaner in a ward pantry with a mildly alkaline all-purpose cleaner, because oil marks on the pantry table and floor were hard to remove. Three weeks later the aluminum trim at the foot of the door looked dull and whitish, and the floor finish on the vinyl floor in front of the pantry had lost its gloss. The supervisor checked three things. The manufacturer’s safety data sheet for that product records a pH of 10 to 12 on the 100 percent product and a dilution of 1 : 20 to 1 : 50. The attendant had diluted it 1 : 5 to make it stronger. The solution was then left to dry without rinsing.
A 1 : 5 solution contains three and a half times as much concentrate as the strongest dose on the data sheet. The alkaline conditions that help release grease also react with some surface materials, and a solution that is not rinsed off stays there until it dries. The attendant needs to understand the meaning of pH 10 to 12, the ingredients in the jerry can, the soil it is aimed at, the sensitive surfaces, and the reason rinsing is part of the job.
Scope
This chapter covers surfactant-based all-purpose cleaners with a pH of 10 to 12 for greasy soil on hard surfaces: the meaning of the pH, the active ingredients, alkali-sensitive surfaces, dilution and rinsing, eye and skin protection, and handling and storage. This chapter is learning material, not a work instruction. The binding dose, protective equipment, and method of use are those written on the label and the safety data sheet of the product actually in use, together with the workplace procedure.
Neutral cleaners, how to read a dilution ratio, residue, and floor drying are covered in Chapter 27 on neutral all-purpose cleaners. How to check the contents of a data sheet is in Chapter 26 on reading the safety data sheets of cleaning products, labels and spills in Chapter 6 · Safety on chemicals in technician work, hazardous mixtures in Chapter 25 on chemical reactivity and incompatibility, and micelles and foam in Chapter 21 on surfactants, colloids, and emulsions. Disinfectants are covered in Chapter 4 · Biology & Microbiology on disinfectants and how they work, glass cleaners in Chapter 29, and acid bathroom cleaners in Chapter 30.
Some work lies outside the authority of cleaning staff and technicians. Stripping and recoating floor finish is done by a flooring contractor appointed by the building manager. Aluminum or paint that is already damaged is assessed by the building technician. An acid rinse to neutralize stone after an alkaline cleaner is the work of a stone-cleaning contractor. A large concentrate spill is handled by the spill response team under the workplace procedure, and eye, skin, or breathing complaints are handled by a doctor or the emergency services.
Mildly alkaline by the numbers: pH 10 to 12
A mildly alkaline all-purpose cleaner is a surfactant-based cleaning liquid whose concentrate has a pH above the neutral range, so that its cleaning power comes from the surfactants and from the alkaline conditions. According to the manufacturer’s safety data sheet for one product in this class, the concentrate is a clear liquid with a pH of 10 to 12 measured on the 100 percent product, a relative density of 1.000 to 1.030, and a dilution of 1 : 20 to 1 : 50.
On the alkaline side, what does the work is the hydroxide ion. At 25 °C, pH and pOH add up to 14.00, so the hydroxide concentration in moles per liter can be calculated from the pH.
At pH 10 the hydroxide concentration is 0.0001 mole per liter, and at pH 12 it is 0.01 mole per liter. The range of 10 to 12 therefore spans a hundredfold difference, and the hydroxide concentration at its upper end is one hundred thousand times the concentration in a neutral solution of pH 7 (Example 1).
The word mild is relative here. The Safer Choice Standard of the United States EPA, a voluntary labeling program, requires the pH of the product as sold to be not less than 2 and not more than 11.5, to minimize the potential for irritation or injury to skin and eyes. A concentrate for a closed dilution-controlled system may exceed that limit, among other conditions if the pH at the most concentrated use dilution stays within the range of 2 to 11.5. A product with a pH range of 10 to 12 sits on both sides of that 11.5 line. The word mild must not be read as gentle on the eyes.
The pH of the use solution is not stated on the data sheet. As a limiting model, if the alkalinity of the concentrate behaves like a strong base with no buffer, a 1 : n dilution lowers the pH by :
This model gives only an estimate. A buffered product falls less, and the dilution water also plays a part; buffers are explained in Chapter 15 on advanced acids and bases. The pH of the use solution is therefore measured with pH paper or a pH meter, not guessed.
Alkylbenzene sulfonates and the other ingredients in the jerry can
Alkylbenzene sulfonates are synthetic detergents in the form of salts of long-chain alkylbenzenesulfonic acids. They work in the same way as soap: the alkylbenzene end is attracted to grease, whereas the negatively charged sulfonate end is attracted to water. Unlike soaps, sulfonate detergents do not form insoluble metal salts in hard water. With a negative charge on the head, alkylbenzene sulfonates are classed as anionic surfactants, as covered in Chapter 21 on surfactants, colloids, and emulsions.
Two versions of the safety data sheet for a product in this class were both issued on February 22, 2024 and are both still valid as of November 2026, yet they contain different ingredient lists. The first version is valid until February 21, 2027 and the second until February 21, 2029.
| Ingredient (name on the data sheet) | CAS number | Content (%) | Listed in |
|---|---|---|---|
| Sodium dodecylbenzene sulfonate | 25155-30-0 | 5 to 10 | first version |
| Linear alkylbenzene sulfonates | 27323-41-7 | 1 to 5 | first version |
| Sodium poly(oxyethylene) dodecyl ether sulfate | 68585-34-2 | 1 to 5 | both versions |
| Alkyl dimethyl benzyl ammonium chloride | 63449-41-2 | 5 to 10 | second version |
| Ethylene glycol monoethyl (the name as written is cut short) | 110-80-5 | 1 to 5 | second version |
This chapter does not choose which version is correct for a particular jerry can. The applicable ingredient list is asked of the supplier through the purchasing department, and how to match a data sheet to a product is covered in Chapter 26 on reading the safety data sheets of cleaning products. Until that is clear, the attendant treats the product according to the more severe version.
Two ingredients in the second version need to be recognized. Alkyl dimethyl benzyl ammonium chloride is given by the CDC and Infection Control Africa Network (ICAN) guidance as an example of a quaternary ammonium compound, that is, a low-level disinfectant that also has detergent properties, irritates the skin, can irritate the respiratory tract, and persists in the environment and waterways. The data sheet of this product states its use as an all-purpose cleaner, so this chapter treats it as a cleaner. A disinfection claim is read only from the product label and is covered in Chapter 4 · Biology & Microbiology on disinfectants and how they work.
CAS number 110-80-5 in the NIOSH Pocket Guide is 2-ethoxyethanol, with the synonym ethylene glycol monoethyl ether. Those United States data record exposure routes that include inhalation and skin absorption, a NIOSH recommended exposure limit of 0.5 ppm as a time-weighted average with a skin notation, and target organs that include the reproductive system. That figure applies to the substance in workplace air, not to a mixture containing 1 to 5 percent of it. The lesson taken is to keep the concentrate off the skin and to work in a ventilated room.
Greasy soil: why alkaline conditions help
Animal fats contain esters of fatty acids. When fat is treated with a base such as potassium carbonate or sodium hydroxide, glycerol and salts of fatty acids are formed, and those fatty acid salts are soap. This hydrolysis of fat by alkali is called saponification. That is why alkaline conditions help with fatty soil: part of the fat can turn into material that dissolves in water.
The CDC guideline on disinfection and sterilization notes that alkaline-based cleaning agents are used because they dissolve protein and fat residues efficiently, but that they can be corrosive. That statement was written for the cleaning of medical instruments, and both sides of it need to be kept in mind in a building. In an all-purpose cleaner, the alkaline conditions work together with the surfactants and scrubbing; they do not replace them. The CDC and ICAN guidance states that cleaning products remove organic material and suspend grease or oil by being combined with water and scrubbed.
The target of this class of cleaner is greasy soil on hard surfaces, such as hand marks, oil splashes, and a film of grease on a pantry floor. Limescale and rust are targets for acid cleaners and are covered in Chapter 30 on acid bathroom cleaners. When the soil is light and the surface is sensitive, the neutral cleaner of Chapter 27 on neutral all-purpose cleaners is the first choice.
Alkali-sensitive surfaces
Aluminum is the clearest example. Aluminum is amphoteric, meaning that it reacts with acids as well as with bases, and in both reactions hydrogen gas is formed. Aluminum trim, door frames, ladders, and carts are therefore not regarded as resistant to alkaline cleaners. Strong bases and aluminum as an incompatible pair are covered in Chapter 25 on chemical reactivity and incompatibility.
Paint and protective coatings are the second group. The United States National Park Service preservation guidance on cleaning masonry buildings notes that alkaline paint removers are used to remove oil, latex, and acrylic paints, and that alkaline cleaners may also remove some acrylic water-repellent coatings. That guidance deals with products for masonry facades, not all-purpose cleaners, but the direction is the same. Painted surfaces and floors that carry a protective finish are tested first before they are cleaned with an alkaline cleaner.
Stone and masonry are the third group. The same guidance writes that alkaline cleaners can stain sandstones that contain a ferrous compound, that they do not etch as acids do but are caustic and can burn the surface, and that they can deposit potentially damaging salts that are difficult to rinse out thoroughly. For acid-sensitive stone such as marble and limestone, the guidance does choose alkaline cleaners over acids, on condition that they are tested first on an inconspicuous spot and rinsed until neutral. Marble care is covered in Chapter 32 on crystallization and polishing of marble floors.
Work tools can be damaged too. The CDC and ICAN guidance notes that microfiber cloths can be damaged by high pH. The hidden-spot test is carried out as in Chapter 27 on neutral all-purpose cleaners: the use solution at the label dose, for the planned working time, then rinsed, dried, and compared.
Dilution and rinsing
According to the manufacturer’s safety data sheets for products in this class, the dilution is 1 : 20 to 1 : 50, and this chapter gives no other dose. Reading the ratio as one part concentrate plus n parts water, the volume of concentrate for a volume of use solution is
where and are in the same unit. The CDC and ICAN guidance asks that solutions always be prepared according to the manufacturer’s instructions, because a solution stronger than recommended adds unnecessary risk to people and the environment. With an alkaline cleaner, that risk takes the form of a higher pH on the surface and on the skin (Example 4). When diluting, the concentrate is added to the water, not the water to the concentrate.
With an alkaline cleaner, rinsing is part of the job. The National Park Service guidance sets out the sequence for stone: the surface is wetted first, the alkaline cleaner is left to dwell for the time recommended by the manufacturer or determined by testing, it is then rinsed off with water, and after that pH strips are applied to the surface to make sure it is neutral. The same sequence can serve as a way of thinking for floors and tables: wet, allow time as the label says, rinse, and check. pH paper on a surface still wet with the last rinse water is compared with pH paper in the tap water used for rinsing.
For stone, that guidance adds one more step, a slightly acidic wash to neutralize, followed by a water rinse. That step is the work of a stone-cleaning contractor. Cleaning staff do not follow an alkaline cleaner with an acid cleaner and do not mix the two; they rinse with clean water until the pH paper shows the tap-water figure. How many rinses are needed depends on the amount of water in each rinse (Example 6). A floor wet with rinse water is closed off from passers-by until it is dry.
Eyes, skin, and first aid
The two data sheet versions above also differ in classification. The second version classifies the product as sold as serious eye damage or eye irritation Category 1, whereas the first version writes Category 2B. For choosing protection, the more severe category is used until the supplier explains.
HSE in Great Britain notes that many cleaning substances are hazardous because they are corrosive and can cause skin and eye burns if splashed. HSE asks that the protective clothing provided always be worn when handling cleaning substances, especially concentrates, and that eye protection suitable for splashes, such as chemical splash goggles or a face shield, be worn if there is any danger of splashing and when cleaning at eye level or above. The CDC and ICAN guidance names chemical-resistant gloves, such as nitrile, for preparing solutions. For preparing disinfectant solutions without a data sheet, that guidance asks for chemical-resistant gloves, a gown or apron, and a face mask with goggles or a face shield. That set is a reasonable benchmark for an alkaline concentrate whose data sheet is not yet clear.
First aid for the eyes starts at once. The NIOSH procedure for substances coded irrigate immediately is to wash the eyes right away with large amounts of water, occasionally lifting the lower and upper lids, and then to get medical attention immediately. For the skin, the water flush procedure is to flush the contaminated skin with water promptly, to remove at once any clothing the liquid has penetrated, and to get medical attention if irritation persists after washing. Where tap water is not readily available near the workplace, HSE asks for at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers for eye irrigation. If the liquid is swallowed or someone has difficulty breathing, call a doctor or the emergency services and take the product’s safety data sheet along.
Wet work is covered in Chapter 27 on neutral all-purpose cleaners, and chemical burns from alkalis in Chapter 41 · Biology & Microbiology on skin and chemicals.
Handling and storage
According to the manufacturer’s safety data sheets for products in this class, the storage temperature is 0 to 50 °C. HSE asks for a storage place away from heat, sunlight, foodstuffs, and members of the public, especially children, with all containers lidded and clearly labeled, and with decanting containers made of a suitable material. For an alkaline cleaner, suitable materials do not include aluminum, because aluminum reacts with bases.
Do not mix cleaning products. HSE writes that bleach mixed with acidic toilet cleaners or ammonia gives off harmful gases, and asks that cleaning substances never be mixed. An alkaline cleaner that meets an acid cleaner neutralizes it and releases heat, as covered in Chapter 25 on chemical reactivity and incompatibility. Buckets, bottles, and mops that move from one product to another are rinsed first.
The way a product is used also determines exposure. HSE notes that some substances can cause breathing problems if oversprayed or used without adequate ventilation, and asks that cleaning substances be used only in well-ventilated areas. The CDC and ICAN guidance prefers squeeze bottles over spray bottles for wetting cleaning cloths, asks for a preparation room with access to an eyewash station, and asks that used solution be disposed of through the utility sink or floor drain of the cleaning room. Concentrate, jerry can remainders, and container wash water are not poured into storm drains or onto the ground. The binding disposal method is set by the workplace according to the product’s safety data sheet.
Worked example
The figures in the examples below are practice figures unless their origin is stated, and so is the 1 : 5 dilution in the opening case.
Example 1: what pH 10 and pH 12 mean. The pH range of 10 to 12 comes from the product data sheet. At pH 10, , so the hydroxide concentration is mole per liter. At pH 12, , so the concentration is mole per liter. The ratio is times. Relative to a neutral solution of pH 7, pH 12 is units away, that is, times.
Example 2: concentrate for a bucket and a bottle. For 10 liters of use solution, that is, 10,000 mL, the strongest dose of 1 : 20 needs mL of concentrate and the weakest dose of 1 : 50 needs mL. For a 500 mL bottle, the dose is mL to mL. Amounts that small are measured with a graduated cylinder, not with a bottle cap.
Example 3: estimated pH of the use solution. With the no-buffer model, a pH 12 concentrate diluted 1 : 20 becomes , and diluted 1 : 50 it becomes . A pH 10 concentrate becomes and . A use solution made from concentrate at the upper end of the range is still clearly alkaline even after being diluted fifty times.
Example 4: the solution in the opening case. At 1 : 5, the concentrate fraction is , whereas at 1 : 20 the fraction is . That solution is times stronger than the strongest dose. With the same model, its pH is , which is units higher than the 1 : 20 solution.
Example 5: surfactant content of the use solution. In the first version of the data sheet, the contents of the three surfactants add up to at least percent and at most percent of the concentrate. At 1 : 20, the content in the use solution is percent to percent. At 1 : 50, it is percent to percent.
Example 6: how many rinses. After mopping, a 30 m² floor still carries a film of solution 0.05 mm thick. A 1 mm film over 1 m² has a volume of 1 liter, so the volume is liters. A rinse with 9 liters of clean water that mixes evenly and is then mopped up until the same film remains dilutes that remainder times and, with the no-buffer model, lowers the pH by . From 10.68, one rinse gives . Two rinses dilute it times and give . Rinsing is therefore done more than once and checked with pH paper.
Stop conditions
- Concentrate or solution has got into the eyes: rinse at once with plenty of water while holding the lids open, keep rinsing, and take the person to a doctor or the emergency services without waiting for the complaint to get worse; the supervisor gets the product’s safety data sheet ready.
- An aluminum surface darkens, whitens, or gives off bubbles on contact with the solution: rinse with clean water and do not continue; the building technician assesses the damage.
- Paint or floor finish softens, turns sticky, or lifts: rinse with clean water and report to the supervisor; stripping and recoating are done by a flooring contractor appointed by the building manager.
- There is a pungent smell, or the bucket feels hot, after the alkaline cleaner has met another product, such as an acid cleaner or bleach: leave the room and hand over to the supervisor and the occupational safety and health (K3) officer; call the emergency services if anyone has difficulty breathing.
- pH paper on a rinsed surface still reads far above the tap-water figure: do not coat it, polish it, or open it for use; rinse again with clean water, and if the reading stays high hand over to the supervisor.
- Someone asks the attendant to neutralize a surface with an acid cleaner or to strip floor finish: that work is handed over to a contractor appointed by the building manager.
- Skin is red, stinging, or blistered after contact with concentrate: rinse with water, take off clothing wet with the liquid, and report to the supervisor; examination and treatment are done by a doctor.
- Coughing, difficulty breathing, or stinging eyes while working in an enclosed room: stop, move to fresh air, and report to the supervisor; call a doctor or the emergency services if the complaint does not go away.
- More concentrate has spilled than the equipment on the cart can absorb, or it is flowing toward a drain: keep people away, contain the flow if it is safe, and hand over to the spill response team under the workplace procedure.
- The safety data sheet does not match the jerry can label in name, validity date, or ingredient list: wear protection for the most severe category and ask the purchasing department to obtain the correct data sheet from the supplier before the product is used in a new area.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
Mildly alkaline means gentle on the eyes.
Why is it wrong?
One version of the data sheet classifies the concentrate as serious eye damage or eye irritation Category 1, and the upper end of its pH range is above 11.5. Eye protection is worn when pouring and diluting.
Common misconception
pH 12 is only slightly more alkaline than pH 10.
Why is it wrong?
A difference of two pH units means a hydroxide concentration one hundred times higher. Two jerry cans at different ends of the range are not equally harsh materials.
Common misconception
Once it is diluted, the pH is bound to be neutral.
Why is it wrong?
According to the no-buffer model, a pH 12 concentrate diluted 1 : 50 is still about 10.3. The pH of the use solution is measured.
Common misconception
Stronger cleans faster, and there is no need to rinse.
Why is it wrong?
A stronger solution raises the pH on the surface, and a solution that is not rinsed off stays there until it dries. Rinsing is part of the job.
Common misconception
All-purpose means allowed on every surface.
Why is it wrong?
Aluminum reacts with bases, alkaline cleaners may remove some acrylic coatings, and microfiber cloths can be damaged by high pH. The hidden-spot test is still carried out.
Common misconception
It contains a quaternary ammonium compound, so it is a disinfectant as well.
Why is it wrong?
The data sheet of this product states its use as an all-purpose cleaner. A disinfection claim is read from the label, and disinfection is a separate step after cleaning.
Links to other chapters
Chapter 27 on neutral all-purpose cleaners is the companion to this chapter and contains how to read a dilution, residue, and wet work. Chapter 26 on reading the safety data sheets of cleaning products gives the way to handle two differing versions of a data sheet. Limescale and rust are in Chapter 30 on acid bathroom cleaners, and incompatible pairs of materials in Chapter 25 on chemical reactivity and incompatibility.
Exercises and worked solutions
The figures in the problems are for practice.
Try to answer first, then open the worked solution.
A 6 liter bucket is to be filled with a 1 : 20 use solution, read as one part concentrate plus twenty parts water. How much concentrate is needed?
Check my answer
See the worked solution
The concentrate is mL, and the water is mL. The concentrate is added to the water, not the other way round, and is measured with a graduated cylinder.
How many times higher is the hydroxide concentration of a pH 11 solution than that of a pH 8 solution?
Check my answer
See the worked solution
The difference is pH units, so the hydroxide concentration is times higher. The pH scale is a logarithmic scale, so each unit means a factor of ten.
An attendant is about to clean a greasy aluminum cart with a mildly alkaline cleaner. What is considered?
Check my answer
See the worked solution
Aluminum is amphoteric and reacts with bases, so the cart is not regarded as resistant to alkaline cleaners. The attendant tries a neutral cleaner first; if an alkaline cleaner is still needed, they test it in a hidden spot at the label dose, do not let it dry, and rinse it off thoroughly.
After the alkaline cleaner, scale on the floor is still there, and the attendant is about to pour an acid cleaner straight onto the same spot. What is wrong?
Check my answer
See the worked solution
Cleaning products are not mixed, and an acid cleaner that meets the remains of an alkaline cleaner neutralizes it and releases heat. The floor is rinsed with clean water until the pH paper shows the tap-water figure, and only then is work with an acid cleaner assessed according to Chapter 30 on acid bathroom cleaners.
With the no-buffer model, what is the estimated pH of a use solution made from a pH 11 concentrate diluted 1 : 50, and why can the measured result differ?
Check my answer
See the worked solution
The estimate is . The measured result can differ because a buffered product falls less and the dilution water also plays a part, so the figure used is the reading from pH paper or a pH meter.
Two versions of the data sheet for the same product write different eye hazard categories. What do the attendant and the supervisor do?
Check my answer
See the worked solution
The attendant wears protection for the more severe category, that is, Category 1, while pouring and diluting. The supervisor asks the purchasing department to obtain an explanation and the valid data sheet from the supplier, because no chapter can decide what is in the jerry can.
References
External sources
- OpenStax: Organic Chemistryopenstax.org
- OpenStax: Chemistry 2eopenstax.org
- Cleaningcdc.gov
- Best Practices for Environmental Cleaning in Healthcare Facilities: in Resource-Limited Settingscdc.gov
- Preservation Briefs 1: Assessing Cleaning and Water-Repellent Treatments for Historic Masonry Buildingsnps.gov
- Safe use of cleaning substances in the hospitality industryhse.gov.uk
- EPA's Safer Choice and Design for the Environment (DfE) Standardepa.gov
- NIOSH Pocket Guide to Chemical Hazards: 2-Ethoxyethanolcdc.gov
- First Aid Procedures for Chemical Hazardscdc.gov
Revision history
| Date | Version | Change |
|---|---|---|
| November 15, 2026 | 1 | First published |
How to cite
Kurnia (2026). Mildly alkaline all-purpose cleaners: surfactants and active ingredients, pH 10 to 12, greasy soil, alkali-sensitive surfaces, rinsing, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/pembersih-serbaguna-alkali-ringan-surfaktan-dan-bahan-aktif-ph-10-sampai-12-kotoran-berminyak-permukaan-yang-peka-terhadap-alkali-pembilasan-serta-penanganan-dan-penyimpanan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
A 6 liter bucket is to be filled with a 1 : 20 use solution, read as one part concentrate plus twenty parts water. How much concentrate is needed?
How many times higher is the hydroxide concentration of a pH 11 solution than that of a pH 8 solution?
An attendant is about to clean a greasy aluminum cart with a mildly alkaline cleaner. What is considered?
Nearby chapters
Reading order by shelf: Chemistry · Chapter 29.
Reading order by shelf: Chemistry · Chapter 27.