By Kurnia · Published November 15, 2026 · Version 1 · 21 min read
Neutral all-purpose cleaners
anionic and nonionic surfactants, pH 6 to 8, dilution and the use solution, suitable surfaces, residue and rinsing, and handling and storage
The vinyl floor of a hotel corridor feels sticky even though it is mopped twice a day, because the neutral all-purpose cleaner is poured at more than twice the strongest dose and is not rinsed off. This chapter covers surfactant-based all-purpose cleaners with a pH of 6 to 8: what the pH figure on the safety data sheet means, anionic and nonionic surfactants as the ingredients that actually do the cleaning, how to read a dilution ratio and calculate the use solution, suitable surfaces and testing in a hidden spot, residue and rinsing, skin and eyes, and handling, storage, and disposal. The product data come from manufacturer safety data sheets that are still valid as of November 2026; the binding dose remains the label of the product in use. Repair of damaged surfaces, large spills, and health complaints are written as limits, with the party that takes over.
The vinyl floor of a hotel’s third-floor corridor feels sticky every afternoon and shows shoe prints, even though it is mopped twice a day. The housekeeping supervisor watches how the attendant works: neutral all-purpose cleaner is poured straight from the jerry can into an 8 liter bucket until the foam is thick, roughly 1.6 liters per pour, and then the floor is mopped and left to dry without rinsing. The manufacturer’s safety data sheet for that product gives a dilution of 1 : 10 to 1 : 50. For 8 liters of solution, the strongest dose in that range is about 0.73 liter of concentrate and the weakest about 0.16 liter, so the bucket holds more than twice the strongest dose.
The product is not at fault, and its pH really is neutral. What is wrong is the assumption that a neutral cleaner can be used as freely as one likes because it is not harsh. Excess surfactant does not evaporate with the water. It stays on the floor as a thin layer, and that layer is what feels sticky. The attendant needs to understand four things: what the pH figure on the data sheet means, how surfactants work, how to read a dilution ratio, and what is left behind after the water has dried.
Scope
This chapter covers surfactant-based all-purpose cleaners with a pH of 6 to 8 for hard surfaces: the active ingredients, the meaning of the pH, dilution into a use solution, suitable surfaces, residue and rinsing, and handling and storage. This chapter is learning material, not a work instruction. The binding dose, protective equipment, and method of use are those written on the label and the safety data sheet of the product actually in use, together with the workplace procedure.
How to check the contents of a data sheet is covered in Chapter 26 on reading the safety data sheets of cleaning products, and the SDS in general in Chapter 10 on the SDS and functional classes. Labels, transferring, and spills are in Chapter 6 · Safety on chemicals in technician work, hazardous mixtures in Chapter 25 on chemical reactivity and incompatibility, and micelles and foam in Chapter 21 on surfactants, colloids, and emulsions. Disinfectants are covered in Chapter 4 · Biology & Microbiology on disinfectants and how they work. Mildly alkaline cleaners are in Chapter 28, glass cleaners in Chapter 29, acid bathroom cleaners in Chapter 30, and carpet cleaners in Chapter 34.
Some work lies outside the authority of cleaning staff and technicians. Floors, stone, or protective coatings that are already damaged are repaired by a flooring tradesperson or a contractor appointed by the building manager. A large concentrate spill is handled by the spill response team under the workplace procedure. The settings of an automatic dosing unit are changed by the chemical supplier. Eye, skin, or breathing complaints are handled by a doctor or the emergency services. The attendant dilutes according to the label, tests, cleans, rinses, stores, and reports.
Neutral by the numbers: pH 6 to 8
A neutral all-purpose cleaner is a surfactant-based cleaning liquid for hard surfaces whose pH is close to 7, so that its cleaning power comes from the surfactants and from scrubbing, not from an acid or a base. The best-practice guidance on environmental cleaning in healthcare facilities prepared by CDC with the Infection Control Africa Network (ICAN) recommends, for most cleaning procedures, neutral detergents with a pH between 6 and 8 that dissolve easily in warm and cold water. This chapter uses that range as the meaning of the word neutral.
The pH figure expresses the concentration of hydronium ions in moles per liter on a logarithmic scale, and a neutral solution at 25 °C has a pH of 7.00.
Because the scale is logarithmic, a difference of one pH unit means a tenfold difference in hydronium concentration. pH 6 and pH 8 are each only one unit away from neutral, whereas pH 10 is three units away, that is, a thousand times. Acids, bases, and buffers are explained in Chapter 15 on advanced acids and bases.
According to the manufacturer’s safety data sheet for one product in this class, the concentrate is a clear, light green liquid with a pH of 6.0 to 8.0 measured on the 100 percent product, and a relative density of 1.000 to 1.030. The data sheet of another product in the same class, which is sold ready to use, records a pH of 7.0 to 8.0 at 100 percent and a relative density of 1.000 to 1.020. The note 100 percent means that what was measured is the product in the jerry can, not the solution in the bucket; the pH of the use solution is not stated and also depends on the dilution water.
A product name does not guarantee the pH. The data sheet of a ready-to-use product with the same class name records a pH of 9.0 to 10 at 100 percent. That product is not a neutral cleaner by the 6 to 8 range, and on alkali-sensitive surfaces it is treated like the cleaners in Chapter 28 on mildly alkaline all-purpose cleaners. What is read is the pH figure on the data sheet, not the words all-purpose or general-purpose on the packaging.
Anionic and nonionic surfactants: the ingredients that actually clean
A surfactant is a substance whose molecule has two different ends: a nonpolar hydrocarbon tail that is attracted to oil and a head that is attracted to water. Such molecules position themselves at the boundary between oily soil and water, so that the soil comes away as small suspended droplets that can be rinsed off. In synthetic detergents, the head is a sulfate or sulfonate group. Unlike soaps, which form insoluble calcium and magnesium compounds in hard water, synthetic detergents form soluble products.
Surfactants are distinguished by the charge on the head: an anionic surfactant has a negatively charged head, such as a sulfate group, whereas a nonionic surfactant has an uncharged head. The full classification, micelles, and foam are covered in Chapter 21 on surfactants, colloids, and emulsions. According to the manufacturer’s safety data sheet for one product in this class, the concentrate is a mixture containing the following three surfactants.
| Ingredient (name on the data sheet) | CAS number | Content (%) | Class |
|---|---|---|---|
| Sodium polyoxyethylene(2) alkyl (C10 to C16) ether sulfate | 68891-38-3 | 1 to 5 | anionic, with a sulfate head |
| Nonylphenol polyethylene glycol ether | 9016-45-9 | 1 to 3 | nonionic |
| Cocamidopropyl betaine | 61789-40-0 | 1 to 3 | not stated on the data sheet |
The surfactants listed add up to only 3 to 11 percent of the concentrate, and the rest is not itemized. The data sheet of the ready-to-use product in this class does not contain an ingredient table at all. The absence of that table is not read as proof that the liquid may get into the eyes or be swallowed.
The cleaning power of a neutral cleaner depends on surfactant, water, mechanical action, and time. The CDC and ICAN guidance states that cleaning products remove organic material and suspend grease or oil by being combined with water and scrubbed. For greasy floors, HSE in Great Britain writes that water alone is not effective and that the detergent solution is left on the floor long enough before rinsing, like dirty pans that are soaked first. Because there is no acid or base to help, limescale and rust are not targets for a neutral cleaner; both are covered in Chapter 30 on acid bathroom cleaners and Chapter 31 on rust, scale, and cement residue removers.
Dilution and the use solution
A use solution is the solution that actually touches the surface, that is, the concentrate after it has been mixed with water at the label dose. The safety data sheets of products in this class separate the two states in two columns: the product as sold and the product after dilution. According to those data sheets, the dilution of one product is 1 : 10 to 1 : 50, whereas another product in the same class is sold ready to use, meaning it is not diluted further. This chapter gives no other dose. The dose for each job is read from the product label.
In this chapter the ratio 1 : n is read as one part concentrate plus n parts water. On that reading, the volume of concentrate needed to make a volume of use solution is
where is the volume of concentrate and the volume of use solution in the same unit, and is the number of parts of water. The other reading, one part concentrate in n parts of solution, gives ; for n = 10 the difference is ten percent (Example 1). The data sheet does not explain which reading is meant, so the product label or the supplier decides.
The CDC and ICAN guidance asks that solutions always be prepared according to the manufacturer’s instructions, because most chemicals work at an optimum dilution, and a solution that is too dilute or too concentrated reduces the result and adds unnecessary risk. Standardized measuring containers are used, and where possible the solution is prepared with an automatic dispensing system that is calibrated regularly, because manual dilution is more prone to error. HSE writes the same for floors: the concentration of the detergent determines the result, and too strong a solution can be as ineffective as too weak a one.
Containers of use solution are also subject to rules. A container must be clean, clearly labeled, and marked with an expiration date, washed and dried before refilling, and never topped up over the old remainder. When diluting, the concentrate is added to the water, not the water to the concentrate, and cleaning liquids are not transferred into food or drink containers.
Suitable surfaces and testing in a hidden spot
The reason for choosing a neutral pH is the surface material. The CDC guideline on disinfection and sterilization notes that neutral or near-neutral pH detergent solutions generally provide the best material compatibility together with good soil removal, whereas alkaline-based cleaning agents can be corrosive. That statement was written for the cleaning of medical instruments, and it is used here as the reason for choosing a neutral pH when the soil is light.
Three rules of thumb apply whatever the product:
- Start with the gentlest means. The United States National Park Service preservation guidance on ceramic tile floors writes that cleaning always begins with the gentlest means possible, which may be as simple as warm water.
- Test first in a small hidden spot. The same guidance asks that all cleaning and stain-removal products be tested first on a small, inconspicuous area.
- Choose a product that does no damage, and report damage. The CDC and ICAN guidance asks that products be selected that do not damage surfaces and equipment, and that damaged furniture or surfaces be reported to the supervisor during the preliminary assessment of the room.
The test uses the use solution at the label dose, left on for the planned working time, rinsed off, and dried. The test area is then compared with the area next to it for color, gloss, and feel. Any change means that the product or the method is not used on that surface.
A neutral pH does not remove every limit. Abrasion still does damage: the National Park Service guidance writes that abrasive cleaners, including creams described as mildly abrasive, and mechanical equipment can wear away the protective surface and the decorative design of tiles. Water is still water as well: surfaces that must not get wet and electrical equipment do not become safe to wet just because the cleaner is neutral. Types of floor finish and grout are covered in Chapter 39 · Buildings & Facilities on floors and tiles, and abrasive creams in Chapter 33 on abrasive polishing creams.
Residue and rinsing
Residue is the material left on the surface after the water of the use solution has evaporated, that is, surfactant and soil that has been lifted but not carried away. The water evaporates; the surfactant does not. The amount of residue is proportional to two things the attendant can control: the strength of the solution and the thickness of the liquid film left behind (Example 6).
Residue comes from three directions: a solution that is too strong, mop water that is already dirty, and the absence of rinsing. The two-bucket system addresses the second: one bucket holds the cleaning solution and one holds rinse water, and the mop is rinsed and wrung out in the rinse-water bucket before it is dipped into the solution again, so that the solution stays clean longer.
For tile floors, the National Park Service guidance asks that the floor always be rinsed thoroughly after cleaning, with clean water and preferably twice, and that the cleaning solution not be allowed to dry on the tiles. The CDC and ICAN guidance asks for a periodic rinse step to remove residue when the product used is a combined detergent-disinfectant. Whether rinsing is needed in daily use is read from the product label. If the label does not ask for rinsing, residue is still controlled by the correct dose and a well-wrung mop.
Rinsing adds water to the floor. HSE notes that even a well-wrung mop leaves a thin film of water that is enough to create a slip risk on a smooth floor, that a dry mop shortens the drying time but does not eliminate the risk, and that warning cones only inform people without preventing them from entering. The work is therefore organized: cleaning during quiet hours, working in sections so that there is always a dry path, and closing off access until the floor is dry.
Skin, eyes, and personal protective equipment
Neutral is not the same as harmless. According to the manufacturer’s safety data sheet for one product in this class, the product as sold is classified as eye irritation Category 2A, whereas its use solution is not classified as hazardous. The moment of greatest risk is when the concentrate is poured and diluted.
HSE asks that the protective clothing provided always be worn when handling cleaning substances, especially concentrates. Eye protection suitable for splashes, such as chemical splash goggles or a face shield, is worn if there is any danger of splashing and when cleaning at eye level or above. The CDC and ICAN guidance names chemical-resistant gloves, such as nitrile, for preparing solutions, and asks that the type of personal protective equipment for dilution be read from the safety data sheet. Selection and care of that equipment are covered in Chapter 5 · Safety on personal protective equipment.
Wet work is work that brings the skin into prolonged or frequent contact with water, particularly together with soaps and detergents. HSE notes that such contact can cause dermatitis. A neutral cleaner does not free the attendant from this risk. The steps HSE recommends are to avoid direct contact where possible, to protect the skin with suitable gloves and moisturizer, particularly at the end of the working day, and to check the hands regularly for the early signs of itchy, dry, or red skin. The mechanism of the damage is covered in Chapter 41 · Biology & Microbiology on skin and chemicals.
First aid for splashes of cleaner, according to HSE, is to wash the skin or eyes at once with plenty of water, to seek medical advice if irritation persists, and to tell their manager. Where tap water is not readily available near the workplace, HSE asks for at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers for eye irrigation. If the liquid is swallowed or someone complains of difficulty breathing, call a doctor or the emergency services and take the product’s safety data sheet along.
Handling, storage, and disposal
According to the manufacturer’s safety data sheets for products in this class, the storage temperature of both the concentrate and the ready-to-use product is 0 to 50 °C. HSE adds requirements for the place: away from heat, sunlight, foodstuffs, and members of the public, especially children, with all containers lidded and clearly labeled.
The CDC and ICAN guidance asks for a dedicated room for preparing and storing cleaning products: ventilated and well lit, locked, with a utility sink or floor drain for disposing of used solution, with access to an eyewash station, and holding printed copies of the safety data sheets of all products.
Do not mix cleaning products. The OSHA and NIOSH infosheet from the United States writes that mixing products that contain bleach with products that contain ammonia can cause severe lung damage or death. HSE writes that bleach mixed with acidic toilet cleaners or ammonia gives off harmful gases. Buckets and bottles that change contents are washed first. Hazardous mixtures are covered in Chapter 25 on chemical reactivity and incompatibility.
Disposal follows the ingredients. Nonylphenol ethoxylates, the class of one of the surfactants in the table above, are recorded by the United States EPA as highly toxic to aquatic organisms and as degrading in the environment into nonylphenol. That is the reason concentrate, jerry can remainders, and container wash water are not poured into storm drains, ditches, or the ground. Used solution is disposed of through the utility sink or floor drain of the cleaning room, not in a handwashing sink. The binding disposal method is set by the workplace according to the product’s safety data sheet; B3 waste is covered in Chapter 35 · Water & Water Treatment on B3 waste.
Worked example
The figures in the examples below are practice figures unless their origin is stated, and so are the 8 liter bucket and the 1.6 liter pour in the opening case.
Example 1: concentrate for one bucket. The dilution range of 1 : 10 to 1 : 50 comes from the product data sheet. For 8 liters of use solution, that is, 8,000 mL, the strongest dose needs mL of concentrate and the weakest dose mL. If 1 : 10 is read as one part in ten parts of solution, the result is mL, which is mL more, or about 10 percent.
Example 2: how strong the bucket in the opening case is. A pour of 1.6 liters in 8 liters of solution means liters of water, that is, parts water to one part concentrate, or 1 : 4. The concentrate fraction is , whereas at 1 : 10 the fraction is . The bucket is times stronger than the strongest dose on the data sheet.
Example 3: surfactant content of the use solution. The contents of the three surfactants in the table add up to at least percent and at most percent of the concentrate. At 1 : 10, the content in the use solution becomes percent to percent. At 1 : 50, it is percent to percent. A correct use solution contains at most about one percent surfactant.
Example 4: how many buckets from one jerry can. A 5 liter jerry can at 1 : 20 yields liters of use solution, enough for buckets of 8 liters. With a 1 : 4 pour as in the opening case, the same jerry can yields only liters, that is, buckets.
Example 5: mass of one jerry can. The relative density of the concentrate, 1.000 to 1.030, comes from the data sheet. With the density of water at about 1 kg per liter, a 5 liter jerry can holds kg to kg of liquid. The largest difference from water is kg, that is, 3 percent, so dosing by volume and dosing by mass are almost the same.
Example 6: the residue left on the floor. The mop leaves a film of solution 0.05 mm thick on a floor of 40 m². Its volume is m³, that is, 2 liters or about 2,000 g. At 1 : 10 with the top surfactant content of 1.0 percent, the residue after drying is g, that is, g per m². With the 1 : 4 pour, the top surfactant content is percent, so the residue is g, that is, g per m² every time the floor is mopped.
Stop conditions
- Liquid has got into the eyes and the stinging or redness does not go away after rinsing with plenty of water: keep rinsing, tell the supervisor, and take the person to a doctor or the emergency services together with the product’s safety data sheet.
- A container has no label, the label is illegible, or cleaning liquid is in a used drink bottle: do not use it and do not sniff it to guess the contents; hand it over to the supervisor or the chemical store attendant.
- There is a pungent smell, or eyes and throat sting, after the cleaner has met another product, such as bleach or an acid cleaner: leave the room and hand over to the supervisor and the occupational safety and health (K3) officer; call the emergency services if anyone has difficulty breathing.
- A surface changes color, turns dull, or its coating lifts during the hidden-spot test or during work: rinse with clean water and report to the supervisor; the repair is done by a flooring tradesperson or a contractor appointed by the building manager.
- A slippery wet floor cannot be closed off from passers-by: guard the wet section until it is dry and ask the supervisor to arrange another time or an alternative route before mopping the next section.
- The skin of the hands is red, itchy, cracked, or blistered: stop wet work and report to the supervisor; examination and treatment are done by a doctor.
- More concentrate has spilled than the equipment on the cart can absorb, or it is flowing toward a drain: keep people away, contain the flow if it is safe, and hand over to the spill response team under the workplace procedure.
- The product’s safety data sheet is missing, has passed its validity date, or records a pH outside 6 to 8 for a product assumed to be neutral: do not use it on sensitive surfaces until the purchasing department has obtained a valid data sheet from the supplier.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
Neutral means harmless, so no protection is needed.
Why is it wrong?
The concentrate of one product in this class is classified as eye irritation Category 2A, and wet work with any detergent can cause dermatitis. Eye protection is worn when pouring concentrate and gloves when working.
Common misconception
The more cleaner, the cleaner the result.
Why is it wrong?
Too strong a solution can be as ineffective as too weak a one, and the excess surfactant stays on the floor as residue. The dose used is the label dose.
Common misconception
1 : 10 always means one tenth.
Why is it wrong?
The ratio can mean one part plus ten parts water or one part in ten parts of solution, and the results differ by about ten percent. The label or the supplier decides the reading.
Common misconception
All all-purpose cleaners are neutral.
Why is it wrong?
One ready-to-use product with the same class name has a pH of 9.0 to 10. What decides is the pH figure on the data sheet, not the name on the packaging.
Common misconception
Neutral means suitable for every surface.
Why is it wrong?
A neutral pH only removes attack by acids and bases. Water, scrubbing, and residue can still do damage, so the hidden-spot test is still carried out.
Links to other chapters
Chapter 26 on reading the safety data sheets of cleaning products gives the way to check the figures used here, and Chapter 21 on surfactants, colloids, and emulsions gives the basis for how surfactants work. When the soil is greasy and a neutral cleaner is not enough, the next option is covered in Chapter 28 on mildly alkaline all-purpose cleaners. The floor as a material is covered in Chapter 39 · Buildings & Facilities on floors and tiles.
Exercises and worked solutions
The figures in the problems are for practice.
Try to answer first, then open the worked solution.
A 750 mL spray bottle is to be filled with a 1 : 20 use solution, read as one part concentrate plus twenty parts water. How much concentrate and how much water are needed?
Check my answer
See the worked solution
The concentrate is mL, rounded to 36 mL, and the water is mL. The concentrate is added to the water, and then the bottle is labeled with its contents and the date.
A product described as a general-purpose cleaner records a pH of 9.0 to 10 on its data sheet. Why is it not treated as a neutral cleaner?
Check my answer
See the worked solution
pH 9 and pH 10 are two and three units away from neutral, so their hydronium concentration is one hundred to one thousand times lower than that of a pH 7 solution. The neutral range is 6 to 8, so the product is treated as a mildly alkaline cleaner.
An attendant adds a little bleach to the bucket of neutral cleaner so that the floor is freed of germs at the same time. What is wrong?
Check my answer
See the worked solution
Cleaning products are not mixed, because a mixture with bleach can give off harmful gases and its contents no longer match any label or data sheet. If the floor needs disinfecting, that is a separate step after cleaning, with the product and method set by the workplace.
The thermometer in a storeroom with a sheet-metal roof reads 53 °C at midday, and jerry cans of cleaner are stored there. What is done?
Check my answer
See the worked solution
A temperature of 53 °C is °C above the storage limit of 0 to 50 °C. The jerry cans are moved to a cooler room, and any jerry can that is bulging or whose contents have changed is set aside for the storeroom attendant.
A 60 m² floor is mopped with a 1 : 20 solution and the mop leaves a 0.05 mm film. With a top surfactant content of 11 percent in the concentrate, how much residue per square meter remains after drying?
Check my answer
See the worked solution
The film volume is m³, that is, 3 liters or about 3,000 g. The top surfactant content of the use solution is percent, so the residue is g, that is, g per m².
The skin on an attendant’s hands is dry and itchy, even though they use only a neutral cleaner. Why does this happen and what is done?
Check my answer
See the worked solution
Prolonged or frequent contact with water and detergent can cause dermatitis even when the pH is neutral, because the cause is wet work, not an acid or a base. The attendant wears gloves and uses moisturizer, reports to the supervisor, and is examined by a doctor if the skin is cracked or blistered.
References
External sources
- Best Practices for Environmental Cleaning in Healthcare Facilities: in Resource-Limited Settingscdc.gov
- OpenStax: Chemistry 2eopenstax.org
- Slips and trips: The importance of floor cleaninghse.gov.uk
- Safe use of cleaning substances in the hospitality industryhse.gov.uk
- Protecting Workers Who Use Cleaning Chemicalscdc.gov
- How do I prevent skin problems in my business?hse.gov.uk
- Preservation Briefs 40: Preserving Historic Ceramic Tile Floorsnps.gov
- Risk Management for Nonylphenol and Nonylphenol Ethoxylatesepa.gov
- Cleaningcdc.gov
Revision history
| Date | Version | Change |
|---|---|---|
| November 15, 2026 | 1 | First published |
How to cite
Kurnia (2026). Neutral all-purpose cleaners: anionic and nonionic surfactants, pH 6 to 8, dilution and the use solution, suitable surfaces, residue and rinsing, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/pembersih-serbaguna-netral-surfaktan-anionik-dan-nonionik-ph-6-sampai-8-pengenceran-dan-larutan-pakai-permukaan-yang-cocok-sisa-dan-pembilasan-serta-penanganan-dan-penyimpanan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
A 750 mL spray bottle is to be filled with a 1 : 20 use solution, read as one part concentrate plus twenty parts water. How much concentrate and how much water are needed?
A product described as a general-purpose cleaner records a pH of 9.0 to 10 on its data sheet. Why is it not treated as a neutral cleaner?
An attendant adds a little bleach to the bucket of neutral cleaner so that the floor is freed of germs at the same time. What is wrong?
Nearby chapters
Reading order by shelf: Chemistry · Chapter 28.
Reading order by shelf: Chemistry · Chapter 26.