Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Chemistry · Chapter 33Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 20 min read

    Abrasive polishing cream for hard surfaces

    quartz as the abrasive, surfactants and sulfonic acid, scratches and testing in a hidden spot, surfaces that must not be polished, and handling and storage

    A polishing cream that brightens a stainless steel sink in a hospital kitchen leaves circular scratches on a mirror-bright elevator panel and a dull patch on a marble counter. According to the manufacturer’s safety data sheet for one cream of this class, 30 to 60 percent of its contents is quartz, which is 7 on the Mohs scale and harder than glass, a steel nail, and calcite. This chapter covers abrasive polishing cream for hard surfaces: the contents of two creams of the same class, quartz as the abrasive and what hardness means, the role of anionic and nonionic surfactants and of dodecylbenzene sulfonic acid, testing in a hidden spot before polishing, surfaces that must not be polished, cream residue and quartz dust with its threshold limit value, first aid, the prohibition on mixing with chlorine bleach, and handling and storage. Repairing a surface that is already scratched is stated to be work for the equipment manufacturer or a contractor.

    Section you’re reading: Chapter opening

    A stainless steel sink in a hospital kitchen is covered in brownish stains that do not come off with an ordinary cleaner. A cleaning attendant rubs it with a light brown polishing cream, rinses it, and the sink is bright again. A week later the same cream is used on fingerprints on an elevator door panel that shines like a mirror and on a stain on a reception counter of polished marble. The elevator panel is now full of circular scratches that show from the side, and the marble counter has a dull patch the size of a palm.

    The cream works in the same way in all three places; what differs is the surface. The manufacturer’s safety data sheet for one polishing cream of this class states that 30 to 60 percent of its contents is quartz, that is, crystalline silica. On the Mohs hardness scale quartz is 7, above a steel nail, a glass plate, and the calcite that makes up marble. Before using a cream like this, attendants need to know what it contains, which surfaces it will scratch, and how to test it.

    Scope

    This chapter covers abrasive polishing cream used on metals and other hard surfaces: its contents, how quartz abrades, the role of surfactants, testing before polishing, surfaces that must not be polished, cream residue and its dust, and handling and storage. The product data come from the manufacturer’s safety data sheets for two creams of this class and apply to those two products alone. This chapter is learning material, not a work instruction: the list of intended surfaces and the directions for use are taken only from the product label.

    How to read a data sheet is covered in Chapter 26 on reading safety data sheets for cleaning products. Surfactants are covered in Chapter 21 on surfactants, colloids, and emulsions, the hardness of metals in Chapter 5 · Materials on mechanical properties, stainless steel in Chapter 3 · Materials, glass in Chapter 50 · Buildings & Facilities on building glass and windows, and marble floor polishing in Chapter 32 on marble floor crystallization and polishing. Acid cleaners are in Chapter 30 on acid bathroom cleaners and Chapter 31 on removers for rust, scale, and cement residue. Personal protective equipment is in Chapter 5 · Safety, spills in Chapter 6 · Safety on chemicals in the technician’s work, and hazardous mixtures in Chapter 25 on chemical reactivity.

    Work outside the authority of cleaning attendants and building technicians: repairing a surface that is already scratched or dull, re-polishing a decorative finish, re-plating metal, and re-polishing stone. That work belongs to the equipment manufacturer or supplier and to contractors who specialize in that material.

    What an abrasive polishing cream contains

    Abrasive polishing cream is a cleaning paste that holds fine abrasive grains in a liquid containing surfactants, and it cleans by abrading away a thin layer of dirt together with a little of the surface beneath it. The manufacturer’s safety data sheets for two creams of this class contain the following data.

    ItemFirst creamSecond cream
    Formlight brown paste with a lemon odoropaque white slurry
    Abrasivequartz (CAS 14808-60-7) 30 to 60 percentquartz (CAS 14808-60-7) 30 to 60 percent
    Anionic surfactantdodecylbenzene sulfonic acid and its salt (CAS 27176-87-0) 5 to 10 percentdodecylbenzene sulfonic acid (CAS 68584-22-5) 1 to 5 percent
    Nonionic surfactantalcohol ethoxylate (CAS 68439-46-3) 5 to 10 percentC9-11 alcohol ethoxylate (CAS 68439-46-3) 1 to 5 percent and fatty alcohol ethoxylate (CAS 66455-14-9) 1 to 5 percent
    pH of the undiluted product5.32 to 6.008 to 9
    Solubility in waterinsolubleinsoluble
    Usesold ready to use, for industrial and professional usesold ready to use, for industrial and professional use
    Storage temperature0 to 50 °C0 to 50 °C
    Document validityissued March 9, 2023, valid until March 8, 2028issued January 8, 2024, valid until January 7, 2027

    Both creams use the same abrasive in the same concentration range, but their pH values point in opposite directions: the first is slightly acidic and the second slightly alkaline. This class is therefore not defined by its acid or its base. Its main action is mechanical, and that action is done by the quartz. A range of 30 to 60 percent means that nearly a third to more than half of what is in the container is rock powder (Example 2). The composition tables of both data sheets state quartz, but one of them names the abrasive as a different material in its toxicology section; the type of abrasive is confirmed with the supplier before the cream is used on a soft surface.

    Both are sold ready to use, so they are not diluted and nothing else is added to them. Both data sheets give the intended use only as a cleaning product. The intended surfaces are on the label, and even the label does not know the finish of every object in the building.

    Quartz as the abrasive: hardness and scratches

    Quartz is crystalline silica, SiO₂. NIOSH records it as a colorless, odorless solid that is insoluble in water and is a component of many mineral dusts. The Mohs hardness scale is a scale of relative hardness from 1 to 10, and hardness here means relative resistance to scratching, tested by scratching one material against another. The United States National Park Service gives the following values for the index minerals and for everyday objects.

    MaterialMohs valueCompared with quartz
    Fingernail2.5softer
    Calcite, the mineral that makes up marble and limestone3softer
    Copper penny3.5softer
    Knife and glass plate5.5softer
    Steel nail6.5softer
    Quartz7equal
    Masonry drill bit8.5harder
    Corundum9harder

    The rule is simple: the harder material scratches the softer one. Quartz scratches every material above its row in the table, including glass and a steel nail. This scale is only an order and does not express multiples. For metals it is only a rough comparison; the hardness of metals is measured by the methods in Chapter 5 · Materials on mechanical properties.

    Every grain that is rubbed across the surface cuts a fine groove. Grooves finer than the original finish make the surface look more even and brighter, whereas coarser grooves show up as scratches. The grain size of the quartz is not written in the data sheets of the two creams, so the documents alone cannot tell whether a cream is finer or coarser than the finish of a given surface. Only a test answers that.

    Whatever the result, some material is lost. The National Park Service guidance on the care of metal objects writes that cleaning and polishing remove original metal, and that metal cleaners may leave chemical residues that can generate further corrosion. On a thick, solid object that loss is not noticed. On a thin layer, a few rounds of polishing are enough to use it up (Example 4).

    Surfactants and sulfonic acid

    The quartz grains do not work alone. The liquid around them wets the surface, lifts oil, and keeps the grains and the loosened dirt suspended until they are rinsed off. That is the work of surfactants, which are covered in Chapter 21 on surfactants, colloids, and emulsions.

    Detergents contain a nonpolar hydrocarbon chain, for example C₁₂H₂₅, and an ionic group such as a sulfate or a sulfonate. The hydrocarbon end is attracted to oil, grease, or dirt, whereas the ionic end is attracted to water, so the molecule bridges the two and the oil is lifted as an emulsion. Dodecyl is the name of that twelve-carbon chain. Dodecylbenzene sulfonic acid is the acid form of an anionic surfactant of the alkylbenzene sulfonate class, with a dodecyl chain on a benzene ring that carries a sulfonic acid group. Alcohol ethoxylate is a nonionic surfactant whose head is an uncharged ethoxylate chain.

    The first cream’s data sheet writes its anionic ingredient as the acid and its salt, and the pH of that cream is 5.32 to 6.00. Example 6 shows that this figure is only slightly acidic. Two practical consequences follow:

    1. With a pH that close to neutral, this cream cannot be expected to dissolve scale or rust the way the acid cleaners in Chapter 30 and Chapter 31 do. Stains come off because they are abraded.
    2. Anionic surfactants are not used together with cationic products, for example the quaternary ammonium disinfectants in Chapter 4 · Biology & Microbiology on disinfectants, because the two neutralize each other’s charge. The surface is rinsed clean first before it is disinfected.

    Testing in a hidden spot

    The National Park Service writes that no cleaning project should be undertaken without first applying the cleaning agent to a representative test patch in an inconspicuous location, and that it is generally preferable to underclean than to clean too harshly. That guidance was written for historic buildings, but its reasoning applies generally: material that has been abraded away does not come back. A useful test has four features:

    1. A hidden place, the same material. The test patch is on an underside, a back corner, or a part covered by furniture, on the same material and finish as the part to be worked on.
    2. Small and light. The area is small, the amount of cream is small, the cloth is clean and soft, and the rubbing is light. The National Park Service guidance on the care of silver and copper alloy objects notes that a common mistake is to use too much polish, and that the cloth is replaced often so that dirt and used polish are not rubbed back into the surface.
    3. Rinsed, dried, viewed from the side. Fine scratches are easiest to see in light that comes in from the side, compared with the unrubbed area next to them.
    4. The result is judged honestly. If the test patch looks duller, shinier, streaked, or different in color compared with its surroundings, the cream changes the surface and is not used there.

    If the test fails, rubbing harder to disguise it only spreads the damage. The test result is reported, and the way to clean that surface is asked of the manufacturer or supplier of the equipment.

    Surfaces that must not be polished

    From the hardness of quartz and the preservation guidance above, several surfaces can be stated with certainty to be unsuitable for a quartz cream.

    SurfaceReason
    Polished or honed marble and graniteabrasion removes the finish, like glass that becomes frosted
    Glass, mirrors, and coated glassa glass plate is softer than quartz; glass is covered in Chapter 50 · Buildings & Facilities on building glass and windows
    Glazed ceramicthe glaze is easily damaged by abrasive cleaning
    Soft metals: tin, zinc, lead, copper, aluminumabrasion destroys the texture and appearance of the original surface
    Galvanized metalabrasion wears away the galvanized layer that protects it
    Gilded metal or metal with another thin metal platinga thin layer of gold can be destroyed by polishing
    Clear-coated metalremoval of the clear organic coating harms the object permanently

    Decorative finishes on chrome, nickel alloys, aluminum, and stainless steel call for the same caution. The National Park Service guidance writes that harsh abrasive blasting destroys the original finish of those metals and increases the possibility of corrosion. A cream rubbed by hand is far gentler than blasting, but its grains are still harder than a steel nail, so mirror finishes and fine-brushed finishes are always tested first. Stainless steel and its passive layer are covered in Chapter 3 · Materials on stainless steel.

    The same guidance on the care of silver and copper alloy objects warns that many commercial polishes contain corrosive chemicals or harsh abrasives that can permanently damage delicate surfaces. That warning was written for museum collections, but it also applies to brass nameplates, plated door handles, and plated serving ware in a hotel.

    Cream residue, quartz dust, and skin

    Quartz is insoluble in water, so its grains do not disappear with a quick rinse. Cream residue dries as a white film in corners, gaps, and grooves. That residue does harm in two ways: the grains left behind scratch again when the surface is wiped, and the dried grains can be raised as dust.

    Respirable crystalline silica is crystalline silica dust that is fine enough to be breathed deep into the lungs and too fine to see in normal lighting. The United Kingdom’s HSE notes that this dust can cause silicosis, chronic obstructive pulmonary disease, and lung cancer, and that polishing is among the activities that create it. HSE asks workers not to dry sweep and not to use compressed air to remove dust from clothing; clean-up uses a vacuum of dust class M or H or wet cleaning.

    Permenaker (Minister of Manpower Regulation) 5/2018 sets the threshold limit value (Indonesian nilai ambang batas, NAB) of quartz at 0.025 mg/m³, that is, the time-weighted average concentration for work not exceeding 8 hours a day or 40 hours a week; as of November 2026 JDIH Kemnaker (the Ministry of Manpower’s legal documentation network) lists this regulation as in force.

    For comparison from other countries, the limit recommended by NIOSH in the United States is 0.05 mg/m³, and the United Kingdom’s workplace exposure limit is 0.1 mg/m³ of respirable dust averaged over 8 hours. The dust concentration from polishing with a cream cannot be known without measurement. What can be controlled is the source: while it is wet, the quartz grains are bound in the cream, so cream residue is picked up with a wet cloth before it dries, and residue that has already dried is not brushed or blown off.

    First aid for crystalline silica according to NIOSH: if it gets into the eyes, immediately wash with large amounts of water while occasionally lifting the upper and lower lids, and get medical attention immediately; if large amounts of the dust are breathed in, move the person to fresh air at once. If cream is swallowed or symptoms persist, contact the emergency services or a doctor and take the product label along. Hands that are often wet with surfactant cleaners are protected with gloves according to Chapter 5 · Safety on personal protective equipment, and dermatitis from wet work is covered in Chapter 41 · Biology & Microbiology on skin and chemicals.

    Handling and storage

    The first cream’s data sheet asks that the product not be swallowed, not get in the eyes, on the skin, or on clothing, that its dust and mist not be breathed, that it be used with adequate ventilation, and that hands be washed thoroughly after handling. The cream is stored in a suitable labeled container, out of the reach of children, at 0 to 50 °C. The container is closed tightly after use so that the cream does not dry into a dusty crust on the rim.

    The prohibition on mixing with bleach. The first cream’s data sheet forbids mixing the product with bleach or other chlorinated products because this produces chlorine gas. The CDC writes the same for households: chlorine bleach can release chlorine gas if it is mixed with certain other cleaning products, and cleaners are not to be mixed. In a kitchen, a sink that has just been rubbed with cream is rinsed until clean before it is sanitized with a chlorine solution, and a cloth used with cream is not dipped into a bleach bucket. Other hazardous mixtures are in Chapter 25 on chemical reactivity.

    Leftover product and containers. The first cream’s data sheet asks that the product not be allowed to enter drains, water courses, or the soil, that leftover product be disposed of at an approved waste disposal facility, and that empty containers not be reused. How to manage this is covered in Chapter 35 · Water & Water Treatment on B3 waste.

    Cloths and tools. Cloths used with cream are rinsed separately and are not used on glass or shiny surfaces, because grains trapped in the cloth scratch the next surface. Spilled cream is picked up while it is still wet.

    Worked example

    The figures in the examples below are practice figures, unless their origin is stated.

    Example 1: what quartz scratches. Quartz is 7. From the Mohs table, a fingernail (2.5), calcite (3), a copper penny (3.5), a glass plate (5.5), and a steel nail (6.5) are all below 7, so all five can be scratched. A masonry drill bit (8.5) and corundum (9) are above 7, so they are not scratched. The smallest difference is 7−6.5=0.57 - 6.5 = 0.5 for the steel nail and the largest is 7−2.5=4.57 - 2.5 = 4.5 for the fingernail. Those differences are only an order, but the conclusion is firm: even a glass plate and a steel nail are softer than the grains in the cream.

    Example 2: contents of one 500 g container. For the first cream, the quartz is 0.30×500=1500.30 \times 500 = 150 g to 0.60×500=3000.60 \times 500 = 300 g. Each surfactant class is 0.05×500=250.05 \times 500 = 25 g to 0.10×500=500.10 \times 500 = 50 g. The remainder, that is, other ingredients not itemized in the data sheet, is at most 500−150−25−25=300500 - 150 - 25 - 25 = 300 g and at least 500−300−50−50=100500 - 300 - 50 - 50 = 100 g. A range that wide means that two containers of the same class can differ in abrasive power.

    Example 3: quartz left behind. An attendant uses 15 g of cream on one sink. Its quartz is 0.30×15=4.50.30 \times 15 = 4.5 g to 0.60×15=90.60 \times 15 = 9 g. If 1 percent of that amount is left in corners and gaps, the residue is 0.01×4.5=0.0450.01 \times 4.5 = 0.045 g to 0.01×9=0.090.01 \times 9 = 0.09 g, that is, 45 to 90 mg of grains that will dry in place.

    Example 4: a thin layer versus solid metal. Suppose a plated faucet has a layer 0.5 micrometer thick and each polishing removes 0.05 micrometer. That layer is gone after 0.5/0.05=100.5/0.05 = 10 rounds of polishing. A solid plate 1 mm thick, that is, 1,000 micrometers, is gone only after 1,000/0.05=20,0001{,}000/0.05 = 20{,}000 rounds. Both the thickness and the removal rate were chosen for practice; what is being learned is the comparison.

    Example 5: a little dust in a small room. A dishwashing room of 4 m by 3 m by 2.7 m has a volume of 4×3×2.7=32.44 \times 3 \times 2.7 = 32.4 m³. At the quartz NAB of 0.025 mg/m³, the respirable quartz dust suspended evenly in that room is 32.4×0.025=0.8132.4 \times 0.025 = 0.81 mg. Compared with the 45 mg of residue in Example 3, that amount is 0.81/45=0.0180.81/45 = 0.018, less than 2 percent. What fraction of dried residue actually becomes respirable dust is not known, so the residue is picked up wet and is not brushed.

    Example 6: how acidic pH 5.32 is. The hydrogen ion concentration is calculated from [H+]=10−pH[\mathrm{H^+}] = 10^{-\text{pH}} in mol/L. For the first cream, 10−5.32=4.8×10−610^{-5.32} = 4.8 \times 10^{-6} mol/L to 10−6.00=1.0×10−610^{-6.00} = 1.0 \times 10^{-6} mol/L. Neutral water has 1.0×10−71.0 \times 10^{-7} mol/L, so the cream is 10 to 48 times more acidic than neutral water. The second cream, with a pH of 8 to 9, lies 10 to 100 times below neutral water.

    Stop conditions

    1. The material or finish of the surface is unknown, or the test in a hidden spot has not been done: do not polish. Ask the building technician or the equipment supplier.
    2. The test patch looks dull, streaked, shinier than its surroundings, or different in color: stop and report to the supervisor. The repair belongs to the equipment manufacturer or a contractor.
    3. The surface turns out to be polished marble or granite, glass or a mirror, glazed ceramic, a soft metal, galvanized metal, plated metal, or clear-coated metal: do not polish it with a quartz cream. The way to clean it is determined by the manufacturer or supplier of that material.
    4. Cream gets into an eye: immediately wash with large amounts of water and get medical attention immediately.
    5. Someone coughs or is short of breath after brushing or blowing off dried cream residue: move the person to fresh air, stop the work, and report to the person responsible for occupational safety and health (K3). If symptoms persist, contact a doctor.
    6. There is chlorine bleach or a chlorine sanitizer on the surface, in the bucket, or on the cloth, or there is an order to mix the cream with another product: do not start. Rinse with clean water and report to the supervisor.
    7. A container has no label, or the safety data sheet is not available or is past its validity date: do not use it. The purchasing department requests a valid document from the supplier.
    8. A large amount of dried cream residue has built up, for example in a storeroom or in a door track: do not dry sweep it or blow it off. Trained personnel clean it up by wet cleaning or with a vacuum of dust class M or H.
    9. The skin of the hands turns red, itches, or cracks after work with the cream: stop the contact and report to the person responsible for K3 or the company doctor.
    10. There is a request to remove scratches from a decorative panel by rubbing harder: refuse. That work belongs to the equipment manufacturer or a contractor.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    The cream feels smooth on the hands, so it does not scratch.

    Why is it wrong?

    What feels smooth is the liquid. The grains are quartz, which is harder than glass and a steel nail.

    Common misconception

    If the stainless steel sink was fine, every metal is fine.

    Why is it wrong?

    Soft metals, plated metals, and mirror finishes respond differently to the same abrasive. Every material and finish is tested on its own.

    Common misconception

    The harder you rub, the cleaner it gets.

    Why is it wrong?

    Rubbing harder abrades away more material, not only dirt. Polishing always removes a little metal or coating.

    Common misconception

    The white residue left behind is only dried soap.

    Why is it wrong?

    That residue contains quartz grains that do not dissolve. Residue is picked up wet, not brushed or blown off.

    Common misconception

    Its pH is close to neutral, so it can be mixed with anything.

    Why is it wrong?

    The data sheet of one cream of this class forbids mixing with bleach because this produces chlorine gas, and its anionic surfactant is incompatible with cationic products.

    Common misconception

    Scratches can be removed by polishing again with the same cream.

    Why is it wrong?

    The grains that made the scratches cannot make a finish finer than themselves. Repairing a finish is work for the manufacturer or a contractor.

    Chapter 32 on marble floor crystallization and polishing covers an abrasive that works together with an acid reaction on stone, whereas the cream in this chapter is nearly neutral and works mechanically. Chapter 3 · Materials on stainless steel explains the passive layer that recovers after a scratch and the danger of chloride residue, and Chapter 4 · Materials on copper, brass, bronze, and aluminum covers the soft metals named in the table. Silica dust from building work is in Chapter 18 · Safety on asbestos and hazardous materials during renovation.

    Exercises and worked solutions

    The figures in the questions are for practice.

    Try to answer first, then open the worked solution.

    1. Using the Mohs values in this chapter, determine which of these can be scratched by a quartz cream: a copper penny, a glass plate, and a masonry drill bit.

      Check my answer
      See the worked solution

      The copper penny (3.5) and the glass plate (5.5) are softer than quartz (7), so both can be scratched. The masonry drill bit (8.5) is harder, so it is not scratched by quartz grains.

    2. A container holds 250 g of the second cream. What is the range of its quartz mass, and what is the range of the total mass of its three surfactants?

      Check my answer
      See the worked solution

      The quartz is 0.30×250=750.30 \times 250 = 75 g to 0.60×250=1500.60 \times 250 = 150 g. Each surfactant is 1 to 5 percent, that is, 2.5 to 12.5 g, so the three together come to 3×2.5=7.53 \times 2.5 = 7.5 g to 3×12.5=37.53 \times 12.5 = 37.5 g.

    3. The cream’s label says the product is suitable for stainless steel. Why is a mirror-finish stainless steel elevator panel still tested first, and how is the test done?

      Check my answer
      See the worked solution

      The label names the material, not the finish, and quartz grains are harder than a steel nail on the Mohs scale, so a mirror finish can turn streaked. The test is done on a hidden part with a little cream and light rubbing, then rinsed, dried, and viewed from the side; if it looks different from its surroundings, the cream is not used.

    4. Dried cream residue has built up in an elevator door track. The elevator car measures 2 m by 1.5 m by 2.4 m. How many milligrams of respirable quartz dust equal the NAB in that car, and how is the residue cleaned up?

      Check my answer
      See the worked solution

      The car volume is 2×1.5×2.4=7.22 \times 1.5 \times 2.4 = 7.2 m³, so at the NAB of 0.025 mg/m³ the amount is 7.2×0.025=0.187.2 \times 0.025 = 0.18 mg. An amount that small shows why dried residue is not brushed or blown off; the residue is cleaned up with a wet cloth or a vacuum of dust class M or H.

    5. A kitchen attendant wants to add bleach to the cream so that the sink is sanitized at the same time. What is the answer?

      Check my answer
      See the worked solution

      The answer is no, because mixing with bleach or chlorinated products produces chlorine gas and cleaning products are not mixed. The sink is first rinsed clean of cream and only then sanitized according to the kitchen procedure.

    6. The plating on a door handle is 0.3 micrometer thick, and each polishing removes 0.02 micrometer. If it is polished once a week, how long does the plating last?

      Check my answer
      See the worked solution

      The plating is gone after 0.3/0.02=150.3/0.02 = 15 rounds of polishing, that is, 15 weeks. This calculation shows why plated metal is not polished with an abrasive cream and is cleaned according to its manufacturer’s instructions.

    References

    External sources

    • NIOSH Pocket Guide to Chemical Hazardscdc.gov
    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
    • Control of exposure to silica dust: A guide for employeeshse.gov.uk
    • Mohs Hardness Scalenps.gov
    • Preservation Briefs 6: Dangers of Abrasive Cleaning to Historic Buildingsnps.gov
    • Appendix O: Curatorial Care of Metal Objectsnps.gov
    • OpenStax: Chemistry 2eopenstax.org
    • Chlorinecdc.gov
    • Caring for Silver and Copper Alloy Objectsnps.gov

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Abrasive polishing cream for hard surfaces: quartz as the abrasive, surfactants and sulfonic acid, scratches and testing in a hidden spot, surfaces that must not be polished, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/krim-poles-abrasif-untuk-permukaan-keras-kuarsa-sebagai-pengikis-surfaktan-dan-asam-sulfonat-goresan-dan-uji-di-tempat-tersembunyi-permukaan-yang-tidak-boleh-dipoles-serta-penanganan-dan-penyimpanan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated
    1

    Using the Mohs values in this chapter, determine which of these can be scratched by a quartz cream: a copper penny, a glass plate, and a masonry drill bit.

    2

    A container holds 250 g of the second cream. What is the range of its quartz mass, and what is the range of the total mass of its three surfactants?

    3

    The cream’s label says the product is suitable for stainless steel. Why is a mirror-finish stainless steel elevator panel still tested first, and how is the test done?

    Self-assessment progress0%

    Nearby chapters