Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Chemistry · Chapter 31Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Rust, scale, and cement residue removers

    oxalic acid and sulfamic acid, how acids dissolve rust and lime, contact time, rinsing and neutralization, and handling and storage

    After a hotel bathroom renovation, the new tiles are covered with a film of cement residue and the linen room floor has rust stains, and a worker proposes dissolving acid crystals as strong as possible, leaving them on overnight, and mopping with bleach. This chapter explains why all three proposals are wrong. It covers two classes of product according to the manufacturer’s safety data sheet for one product of each class: a liquid rust and scale remover containing oxalic acid dihydrate at 1 to 5 percent, and cement film remover crystals containing sulfamic acid at 10 to 30 percent with pH 1 to 2 in a 1 percent solution. It discusses how hydrogen ions and oxalate ions dissolve rust, how acid dissolves lime and cement residue, contact time and testing in an inconspicuous spot, rinsing and checking the pH, neutralization and its limits, the hazard of oxalic acid to the kidneys, the ban on mixing with bleach, and handling and storage. Dilution rates and contact times in minutes are not given and are read from the label.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    A hotel has just finished renovating twelve guest bathrooms. The new ceramic floor tiles are covered with a thin grayish film of leftover grout mortar, and in the linen room the concrete floor has orange stains under the feet of an iron rack. The engineering supervisor receives two products from the storeroom: a bottle of liquid rust and scale remover, and a bag of white cement film remover crystals. A worker proposes a quick way: dissolve the crystals as strong as possible, leave them on overnight to finish the job, then mop with bleach to get rid of the acid residue.

    All three proposals are wrong, and the reason lies in the chemistry of the two products. The liquid contains oxalic acid and the crystals contain sulfamic acid. Both are acids, but their targets, strength, and hazards differ. Contact that lasts too long damages tile and grout, and bleach that meets acid releases chlorine gas.

    Scope

    This chapter covers two classes of product, namely liquid rust and scale removers based on oxalic acid and cement film remover crystals based on sulfamic acid: how acids dissolve rust, lime, and cement residue, contact time, rinsing and neutralization, health hazards, the ban on mixing, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of each class. Other products can differ, so what applies in the workplace is the label and the safety data sheet of the product actually in use.

    This chapter is learning material, not a work instruction. Dissolving rates, contact times in minutes, and neutralizer recipes are not given; all of them are read from the product label and the workplace procedure.

    Phosphoric acid bathroom cleaners and the incidents of accidental mixing with bleach are in Chapter 30 on acid bathroom cleaners. Oxalic acid powder for marble floors is in Chapter 32 on crystallization and polishing of marble floors, and how to check a data sheet is in Chapter 26 on reading the safety data sheets of cleaning products. Dishwasher scale is covered in Chapter 9 · Dishwashing on water quality, softeners, scale, and descaling, rust stains on fabric in Chapter 13 · Laundry on stain treatment, how rust forms in Chapter 19 on electrochemical corrosion, limescale in Chapter 16 on solubility and precipitation, hazardous mixtures in Chapter 25 on chemical reactivity and incompatibility, and spills and general first aid in Chapter 6 · Safety on chemicals in technician work.

    Work outside the authority of building technicians and housekeeping staff: repairing the source of rust in reinforcing steel, anchors, or a leaking pipe, repolishing stone or replacing grout that acid has eaten away, handling a large spill, neutralizing rinse water in large quantities, and giving treatment other than first aid. The source of rust in a structure belongs to the structural engineer or the contractor, damaged surfaces belong to the stone and floor care contractor, large spills belong to trained personnel or the emergency response team, rinse water in large quantities belongs to the building’s waste manager, and casualties are handled by a doctor or the emergency services.

    Two acids in two product forms

    According to the manufacturer’s safety data sheet for one rust and scale remover product, the product is a liquid that is soluble in water and is sold ready to use. The ingredient listed is oxalic acid dihydrate, CAS number 6153-56-6, at a concentration of 1 to 5 percent. The pH of the undiluted product is 4.0 to 6.0, its relative density is 1.060 to 1.080, and its classification is serious eye damage category 1. The data sheet was issued on October 21, 2024 and is valid until October 20, 2029.

    The manufacturer’s data sheet for one cement film remover product gives the form as white crystals that are soluble in water, with sulfamic acid, CAS number 5329-14-6, at a concentration of 10 to 30 percent. The pH of a 1 percent solution of that product is 1 to 2, and its classification is skin corrosion category 1 and serious eye damage category 1. The data sheet was issued on February 22, 2024 and is valid until February 21, 2029. The rate for dissolving the crystals is not written in it, so the rate is read only from the label.

    Oxalic acid, with the formula H₂C₂O₄, is an organic acid that has two hydrogen atoms it can release, is a colorless and odorless powder or granular solid, and is commonly in the dihydrate form. Its ionization constants are Ka1=6.0×10−2K_{a1} = 6.0 \times 10^{-2} and Ka2=6.1×10−5K_{a2} = 6.1 \times 10^{-5}, so its first ionization is stronger than that of the phosphoric acid in Chapter 30 on acid bathroom cleaners. Sulfamic acid, with the formula H₃NSO₃, is a solid acid with one hydrogen atom it can release, which is used as a descaler in solid form, as mentioned in Chapter 6 on chemical formulas and nomenclature. A pH of 1 to 2 in a solution of only 1 percent shows that this acid is almost completely ionized in water (Example 3).

    Concentration and pH need to be read together. Free oxalic acid at 1 percent would have a pH of about 1.3, far below the pH 4.0 to 6.0 written for the liquid rust remover (Example 2). That calculation does not show which figure is wrong. All that can be concluded is that most of the oxalate in that product is no longer in the form of free acid, or that the data need to be queried with the supplier, by the method in Chapter 26 on reading the safety data sheets of cleaning products. The serious eye damage classification still applies whatever the answer.

    How acid dissolves rust

    Rust is hydrated iron(III) oxide, Fe₂O₃·xH₂O, which forms when iron is exposed to oxygen and water. How it forms is covered in Chapter 19 on electrochemical corrosion. A rust stain on a floor, tile, or concrete is fine particles of hydrated iron oxide, which give the orange color.

    Oxalic acid acts on rust in two ways. Hydrogen ions react with the iron oxide and hydroxide, so the iron is released into solution as iron(III) ions. Oxalate ions then bind those ions. Oxalate is a bidentate ligand, that is an ion that holds one metal ion with two of its atoms at once, and three oxalate ions bind one iron(III) ion into the complex ion trisoxalatoferrate(III):

    Fe3++3 C2O42−⇌[Fe(C2O4)3]3−\text{Fe}^{3+} + 3\,\text{C}_2\text{O}_4^{2-} \rightleftharpoons [\text{Fe}(\text{C}_2\text{O}_4)_3]^{3-}

    The formation of a complex ion raises the solubility of a sparingly soluble compound, because its metal ion keeps being taken out of the dissolution equilibrium. Iron that is already bound stays in solution and is carried off by the rinse water.

    Stain removal guidance published in 1988 by the National Park Service, the United States building preservation agency, gives three pointers for rust stains. First, the stain is identified, then its source is traced. Stains from rusting iron railings or anchors will reappear as long as the water seepage that drives them is not repaired. Second, metallic stains on acid-resistant surfaces can be removed with a weak acid solution, and oxalic acid is among those named for rust. On acid-sensitive materials such as marble and limestone, what is used is not the acid but its alkaline salt, namely ammonium oxalate. Third, some rust stains come from iron minerals within the stone itself and cannot be removed. Work on marble is covered in Chapter 32 on crystallization and polishing of marble floors.

    How acid dissolves lime and cement residue

    Limescale is calcium carbonate, as covered in Chapter 16 on solubility and precipitation. Its solubility rises sharply in an acidic solution, and with enough acid the reaction runs on until carbon dioxide gas is released:

    CaCO3(s)+2 H+(aq)→Ca2+(aq)+H2O(l)+CO2(g)\text{CaCO}_3(s) + 2\,\text{H}^+(aq) \rightarrow \text{Ca}^{2+}(aq) + \text{H}_2\text{O}(l) + \text{CO}_2(g)

    Cement residue and grout mortar dissolve in the same way. Hardened cement contains calcium compounds that are basic, including calcium hydroxide, part of which turns into carbonate through the carbon dioxide in the air. Hydroxide and carbonate are basic anions, and salts with basic anions dissolve more readily in acid.

    Tile floor guidance from the same agency writes that an acid cleaner is sometimes in fact needed to lift stains from lime or cement mortar on tile. The manufacturer’s data sheet for the sulfamic acid crystals names that function, namely cement film remover.

    Two consequences follow from this chemistry. First, acid does not distinguish cement residue on top of the tile from cement grout between the tiles, so contact that lasts too long eats into the grout. Masonry cleaning guidance from that agency notes that hydrochloric acid dissolves lime-based mortar, damages brick and some stones, and leaves chloride deposits. Acid can also damage the silicates in the glaze of ceramic tile.

    Second, the calcium salt that forms decides the result. Calcium oxalate is sparingly soluble, with a solubility product of 1.96×10−91.96 \times 10^{-9}, smaller than that of calcium carbonate at 8.7×10−98.7 \times 10^{-9}. Oxalic acid on lime therefore replaces one deposit with another, so its ability against limescale cannot be concluded from its acidity alone and follows the label instructions.

    Contact time

    Contact time is how long a cleaner is left to work on a surface before it is rinsed off. That masonry cleaning guidance sets out the general sequence for chemical cleaners: the surface is wetted first, the cleaner is applied, it is left for the time recommended by the manufacturer or, preferably, determined by testing, then it is rinsed off. The surface is kept wet while the acid works, it may be scrubbed lightly with natural or synthetic bristle brushes, and more than one application may be necessary. Dilution rates and contact times vary considerably from one situation to another.

    Three things decide a safe contact time. The reaction rate rises with concentration, temperature, and surface area, as in Chapter 13 on reaction rates, and warmer temperatures speed up the chemical reaction of a cleaner. Even a suitable acid cleaner does damage if it is left on too long or is not rinsed off adequately. Test results can be judged only after the surface has dried completely, so the test in an inconspicuous spot is done before the work, not in the middle of it.

    Wetting the surface first has a chemical reason. Water fills the pores of the tile so that the cleaner does not soak into the tile body, and the tile floor guidance asks for acid cleaners to be used only on a floor that has been thoroughly wetted and had the excess water removed. A large floor is worked in sections, so that the first point to be coated does not exceed the contact time before it is rinsed (Example 6).

    Rinsing and neutralization

    Rinsing removes the acid that has not yet reacted and the salts produced by the reaction. The tile floor guidance asks for floors always to be rinsed thoroughly after cleaning. The masonry cleaning guidance adds one check: after rinsing, pH strips are applied to the surface to make sure the surface has been neutralized completely. Acid residue that is left behind keeps working on grout and metal, and will release chlorine gas if it later meets bleach, as in the incidents in Chapter 30 on acid bathroom cleaners.

    Each rinse only dilutes. If a liquid film of volume vv is left on the floor and is rinsed with water of volume VV, the hydrogen ion concentration becomes

    c1=c0×vv+Vc_1 = c_0 \times \frac{v}{v + V}

    with c0c_0 and c1c_1 the concentrations before and after the rinse, in mol/L, and vv and VV in liters. This formula assumes the liquid is evenly mixed and the rinse water neutralizes nothing. A porous surface gives up acid more slowly than that assumption, so the number of rinses is settled by a pH strip check, not by calculation (Example 5).

    Neutralization is the reaction of an acid with a base that produces a salt and water, as in Chapter 9 on types of reactions in water. That guidance gives a neutralizing step only for alkaline cleaners, which are rinsed with a slightly acidic solution and then rinsed again. Acid cleaners are removed with a water rinse. The data sheets of both products in this chapter list bases as incompatible materials, and the data sheet for the sulfamic acid crystals asks for the product to be kept away from strong bases. For that reason acid residue on a surface is not sprinkled with caustic soda or another basic material on one’s own initiative. If the product label contains a neutralizing step, that step is the one followed.

    Some acid cleaners can be neutralized so that they are safe to discharge to a drain, but that guidance asks for a disposal plan to be drawn up and the local authorities to be contacted before the work begins. In a building, rinse water in large quantities is discussed with the waste manager, as in Chapter 35 · Water & Water Treatment on B3 waste.

    Health hazards and first aid

    Oxalic acid is more than an irritant. NIOSH, the United States occupational safety and health institute, records its routes of entry as inhalation, ingestion, and skin and eye contact. The symptoms are irritation of the eyes, skin, and mucous membranes, eye burns, localized pain, cyanosis, shock, collapse, convulsions, and kidney damage. The kidneys are among its target organs, and NIOSH recommends that an eyewash be available. Permenaker (Minister of Manpower Regulation) 5/2018 sets the threshold limit value for oxalic acid at 1 mg/m³ and the permitted short-term exposure at 2 mg/m³, with the note irritation of the upper respiratory tract and eyes. As of November 2026 that regulation is listed as in force on JDIH Kemnaker, the ministry’s legal documentation site. The meaning of the two limits is explained in Chapter 30 on acid bathroom cleaners.

    For the sulfamic acid crystals, the skin corrosion category 1 classification on the data sheet means that this product can cause burns to the skin and damage to the eyes. Chemical burns are explained in Chapter 41 · Biology & Microbiology on the skin and chemicals. HSE, the British occupational safety authority, gives guidance for cleaning substances in hospitality:

    • Powders are always dispensed with a scoop, never by hand.
    • When diluting, the concentrate is added to the water, not the water to the concentrate.
    • Eye protection suitable for splashes, for example goggles or a visor, is worn if there is any chance of splashing and when cleaning at eye level or above.
    • Rubber gloves are checked for holes, tears, and thin patches, and latex gloves are avoided.
    • Cleaning substances are used only in well-ventilated places.

    First aid follows the product’s data sheet and the workplace procedure. NIOSH guidance for oxalic acid and HSE guidance for chemical injuries:

    1. Eyes. The eyes are immediately washed with large amounts of water while occasionally lifting the upper and lower lids, then the casualty is taken to medical attention immediately. HSE asks for the eye to be flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then for the casualty to be sent to hospital.
    2. Skin. The skin is promptly flushed with water, and clothing that the liquid has soaked through is removed immediately. For chemical burns, HSE asks for the affected area to be flooded with water for 20 minutes and for contaminated clothing that is not stuck to the skin to be removed.
    3. Swallowed. The casualty is taken to medical attention immediately.
    4. Inhaled. The casualty is moved to fresh air at once and gets medical attention as soon as possible.

    The label or the product’s data sheet is taken to the doctor, and what happens next is the decision of the medical personnel.

    The ban on mixing, handling, and storage

    The data sheet for the sulfamic acid crystals states the ban plainly: do not mix with bleach or other chlorinated products, because chlorine gas will form. For oxalic acid, NIOSH records incompatibility with strong oxidizers, silver compounds, strong alkalis, and chlorites. The proposal in the opening case to mop with bleach breaks both, and also the HSE rule for workers: never mix cleaning substances.

    Both data sheets give a storage temperature of 0 to 50 °C. The incompatible materials for the oxalic acid liquid are bases, and for the sulfamic acid crystals bases, metals, and organic materials. This means the crystals and their solution are not held in a metal bucket and are not stored together with bleach or alkaline cleaners. The HSE guidance on storage applies here too: original containers that are labeled and have lids, away from heat, sunlight, and foodstuffs, and never transferred into food or drink containers. Small spills are handled according to Chapter 6 · Safety on chemicals in technician work.

    Worked example

    The figures in the examples below are practice figures, unless their origin is stated, as are the sizes and times in the opening case. A relative density of 1.070 is used as the midpoint of the range on the data sheet, the molar mass of sulfamic acid, 97.09 g/mol, is calculated from its formula, and the molar volume of a gas, 24.5 L/mol, applies at 25 °C and 1 atm.

    Example 1: oxalic acid in one jerry can. A 5 L jerry can of liquid rust remover has a mass of 5×1.070=5.355 \times 1.070 = 5.35 kg, that is 5,350 g. At 1 percent it contains 0.01×5,350=53.50.01 \times 5{,}350 = 53.5 g of oxalic acid dihydrate, and at 5 percent 0.05×5,350=267.50.05 \times 5{,}350 = 267.5 g. The molar mass of oxalic acid is 90.04 g/mol without water of crystallization and 126.00 g/mol as the dihydrate according to Permenaker 5/2018, so those amounts are equivalent to 53.5×90.04/126.00=38.253.5 \times 90.04/126.00 = 38.2 g to 267.5×90.04/126.00=191.2267.5 \times 90.04/126.00 = 191.2 g of oxalic acid without water of crystallization.

    Example 2: pH of free oxalic acid. One liter of liquid at 1 percent contains 0.01×1,070=10.70.01 \times 1{,}070 = 10.7 g of dihydrate, that is 10.7/126.00=0.084910.7/126.00 = 0.0849 mol/L. With the weak acid formula in Chapter 30 on acid bathroom cleaners, x=(−0.060+0.0602+4×0.060×0.0849)/2=0.0474x = (-0.060 + \sqrt{0.060^2 + 4 \times 0.060 \times 0.0849})/2 = 0.0474 mol/L and pH =−log⁡0.0474=1.32= -\log 0.0474 = 1.32. At pH 4.0 the hydrogen ion concentration is only 10−410^{-4} mol/L, that is 0.0474/0.0001=4740.0474/0.0001 = 474 times lower. A difference that large means the concentration and the pH on the data sheet need to be queried with the supplier.

    Example 3: pH of a 1 percent crystal solution. A 1 percent solution means 10 g of crystals per liter. With a sulfamic acid content of 10 to 30 percent, the acid is 1.0 to 3.0 g per liter, that is 1.0/97.09=0.01031.0/97.09 = 0.0103 mol/L to 3.0/97.09=0.03093.0/97.09 = 0.0309 mol/L. If all of it is ionized, pH =−log⁡0.0103=1.99= -\log 0.0103 = 1.99 to −log⁡0.0309=1.51-\log 0.0309 = 1.51. That result lies within the pH 1 to 2 range on the data sheet, and that is possible only if nearly all the acid molecules are ionized.

    Example 4: the lime used up by 100 g of crystals. One hundred grams of crystals contain 10 to 30 g of sulfamic acid, that is 0.103 to 0.309 mol. Each mole of calcium carbonate needs two moles of hydrogen ions, so the lime that can react is 0.103/2=0.05150.103/2 = 0.0515 mol to 0.309/2=0.15450.309/2 = 0.1545 mol. Its mass is 0.0515×100.09=5.150.0515 \times 100.09 = 5.15 g to 0.1545×100.09=15.50.1545 \times 100.09 = 15.5 g, and the carbon dioxide gas is 0.0515×24.5=1.260.0515 \times 24.5 = 1.26 L to 0.1545×24.5=3.790.1545 \times 24.5 = 3.79 L. A thick lump of mortar has a far greater mass than that, so acid makes sense only for a thin film; how to remove thick lumps is decided by the supervisor together with the contractor.

    Example 5: stepwise rinsing. A 12 m² floor holds a liquid film 0.1 mm thick, that is 12×0.0001=0.001212 \times 0.0001 = 0.0012 m³ or 1.2 L, at pH 1.5. Each rinse uses 10.8 L of water, so the hydrogen ion concentration falls to 1.2/(1.2+10.8)=0.11.2/(1.2 + 10.8) = 0.1 times and the pH rises by one unit: 2.5 after the first rinse, 3.5 after the second, and 4.5 after the third. To get past pH 6 takes 6.5−1.5=56.5 - 1.5 = 5 rinses on the assumption of even mixing. For a porous floor that figure is a lower limit, so the result is confirmed with a pH strip.

    Example 6: area of one work section. The label of a product gives a contact time of at least 3 minutes and at most 5 minutes, and the worker needs 0.5 minutes to coat each square meter. If rinsing starts 3 minutes after the last point is coated, the first point has already been exposed to the cleaner for 0.5A+30.5A + 3 minutes, with AA the area of the section in m². The condition 0.5A+3≤50.5A + 3 \le 5 gives A≤4A \le 4 m². An 18 m² floor is divided into 18/4=4.518/4 = 4.5, rounded up to 5 sections.

    Stop conditions

    1. A sharp odor like bleach is noticed, or bleach and chlorinated products are present in the same work area: stop work, leave and clear the room, and do not re-enter only because the odor has gone. The supervisor calls the building emergency response team or the fire department.
    2. The surface is marble, limestone, a stone of unknown type, or glazed tile that has not been tested: do not use either product. The supervisor contacts the material supplier or the stone care contractor.
    3. A test in an inconspicuous spot leaves the surface dull or discolored, or the grout eaten away: stop and rinse. Repair is handed to the stone and floor care contractor.
    4. The rust stain comes from reinforcing steel, anchors, or a leaking pipe, or a stain that has been cleaned reappears: stop the repeated cleaning. The source is examined by a building technician and, for the structure, a structural engineer.
    5. The label gives no dilution rate or contact time, or the safety data sheet is absent, past its validity date, or inconsistent: do not guess the rate. The supervisor asks the supplier for an explanation.
    6. The pH strip still shows acid after repeated rinsing: do not sprinkle caustic soda or another basic material. The supervisor decides the next step according to the label.
    7. Crystals are flying about as dust, or people are coughing and have a stinging nose or throat: stop, leave the room, and restore ventilation before the work is continued by trained personnel.
    8. A splash gets into the eyes, the skin feels burned, or the product is swallowed: give first aid and take the casualty to a doctor or the emergency services. Swallowed oxalic acid is an emergency.
    9. A spill of crystals or solution is larger than the local spill kit can handle, or a spill has reached bleach: clear the room and hand over to trained personnel or the emergency response team.
    10. Metal near the work is fizzing or changing color: stop, rinse, and report to the supervisor.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    Leave it on overnight to finish the job.

    Why is it wrong?

    Acid that is left on too long eats into grout, glaze, and metal, and the damage cannot be rinsed away. Contact time follows the label and the test results.

    Common misconception

    Stronger is bound to be cleaner.

    Why is it wrong?

    Strength raises the reaction rate on every material it touches, including grout and skin. The rate is read only from the label.

    Common misconception

    Bleach or caustic soda neutralizes acid residue.

    Why is it wrong?

    Bleach that meets acid releases chlorine gas, and strong bases are listed as incompatible materials. Acid residue is removed with a water rinse and checked with a pH strip.

    Common misconception

    pH 4 to 6 means the liquid is as mild as water.

    Why is it wrong?

    The data sheet of the same product states serious eye damage category 1, and NIOSH records kidney damage among the effects of oxalic acid. pH is only one of several measures of hazard.

    Common misconception

    A rust stain that has gone will not come back.

    Why is it wrong?

    The stain comes back as long as the source metal is still rusting and wet. Repeated cleaning without repairing the source only repeats the exposure of the surface to acid.

    Chapter 30 on acid bathroom cleaners contains the weak acid pH formula, the meaning of threshold limit values, and the incidents of accidental mixing that form the background to this chapter. Chapter 32 on crystallization and polishing of marble floors uses the reaction of oxalic acid with calcium carbonate deliberately. Chapter 19 on electrochemical corrosion explains the source of rust that has to be repaired.

    Exercises and worked solutions

    The figures in the problems are for practice.

    Try to answer first, then open the worked solution.

    1. A 1 L bottle holds liquid rust remover containing 5 percent oxalic acid dihydrate with a relative density of 1.070. How many grams of oxalic acid dihydrate does it hold?

      Check my answer
      See the worked solution

      The mass of liquid is 1×1.070=1.071 \times 1.070 = 1.07 kg or 1,070 g, so the oxalic acid dihydrate is 0.05×1,070=53.50.05 \times 1{,}070 = 53.5 g. Swallowed oxalic acid needs immediate medical attention, so the bottle is stored labeled and away from drink containers.

    2. A 1 percent solution is made from crystals containing 20 percent sulfamic acid. What is its pH if all the acid is ionized?

      Check my answer
      See the worked solution

      A 1 percent solution contains 10 g of crystals per liter, so the sulfamic acid is 0.20×10=2.00.20 \times 10 = 2.0 g per liter or 2.0/97.09=0.02062.0/97.09 = 0.0206 mol/L. pH =−log⁡0.0206=1.69= -\log 0.0206 = 1.69, still within the 1 to 2 range on the data sheet.

    3. The label gives a contact time of 4 to 6 minutes, and the worker coats 1 minute per square meter. What is the largest area of one work section, and how many sections for a 9 m² floor?

      Check my answer
      See the worked solution

      The condition is 1×A+4≤61 \times A + 4 \le 6, so A≤2A \le 2 m². A 9 m² floor is divided into 9/2=4.59/2 = 4.5, rounded up to 5 sections, so that the first point does not exceed the longest contact time.

    4. Three jobs are waiting: a rust stain on a concrete floor, a film of cement residue on new ceramic tile, and a rust stain on a marble top. Which product for which job?

      Check my answer
      See the worked solution

      The rust stain on concrete suits the oxalic acid liquid, and the film of cement residue on tile suits the sulfamic acid crystals, both after a test in an inconspicuous spot. The marble top is not worked with either because marble is acid-sensitive; that job is handed to the stone care contractor.

    5. A 0.5 L liquid film at pH 2 is rinsed three times, each time with 4.5 L of water. What is the pH afterward on the assumption of even mixing?

      Check my answer
      See the worked solution

      Each rinse dilutes to 0.5/(0.5+4.5)=0.10.5/(0.5 + 4.5) = 0.1 times, so the pH rises by one unit per rinse and becomes 2+3=52 + 3 = 5. That figure is still acidic, so rinsing continues and the result is checked with a pH strip.

    6. After rinsing, a worker wants to sprinkle caustic soda so that the floor becomes neutral quickly. What is the supervisor’s answer?

      Check my answer
      See the worked solution

      The supervisor refuses, because strong bases are listed as incompatible materials on the product’s data sheet. Acid residue is removed with water rinses until the pH strip shows neutral, unless the label contains a separate neutralizing step.

    References

    External sources

    • NIOSH Pocket Guide to Chemical Hazards - Oxalic acidcdc.gov
    • First Aid Procedures for Chemical Hazardscdc.gov
    • Safe use of cleaning substances in the hospitality industryhse.gov.uk
    • Basic advice on first aid at workhse.gov.uk
    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
    • Chemistry 2eopenstax.org
    • Preservation Brief 1: Assessing Cleaning and Water-Repellent Treatments for Historic Masonry Buildingsnps.gov
    • Preservation Briefs 40: Preserving Historic Ceramic Tile Floorsnps.gov
    • Keeping It Clean: Removing Exterior Dirt, Paint, Stains and Graffiti from Historic Masonry Buildingsnps.gov

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Rust, scale, and cement residue removers: oxalic acid and sulfamic acid, how acids dissolve rust and lime, contact time, rinsing and neutralization, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/penghilang-karat-kerak-dan-sisa-semen-asam-oksalat-dan-asam-sulfamat-cara-asam-melarutkan-karat-dan-kapur-waktu-kontak-pembilasan-dan-penetralan-serta-penanganan-dan-penyimpanan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A 1 L bottle holds liquid rust remover containing 5 percent oxalic acid dihydrate with a relative density of 1.070. How many grams of oxalic acid dihydrate does it hold?

    2

    A 1 percent solution is made from crystals containing 20 percent sulfamic acid. What is its pH if all the acid is ionized?

    3

    The label gives a contact time of 4 to 6 minutes, and the worker coats 1 minute per square meter. What is the largest area of one work section, and how many sections for a 9 m² floor?

    Self-assessment progress0%

    Nearby chapters