Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Chemistry · Chapter 30Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Acid bathroom cleaners

    phosphoric acid and low pH, soap scum and water scale, surfaces damaged by acid, the ban on mixing with bleach, personal protective equipment, and handling and storage

    At a hospital in California, a bathroom floor that had just been mopped with a 4 percent phosphoric acid cleaner and already rinsed released chlorine gas as soon as a bleach solution touched it, and the ward was evacuated twice. This chapter covers acid bathroom cleaners from the side of the people who use them in hotels and hospitals: phosphoric acid at 5 to 10 percent and pH 0 to 2 according to the manufacturer’s safety data sheet for one product of this class, how acid dissolves water scale and soap scum, surfaces damaged by acid such as marble, limestone, tile glaze, cement grout, and metals, the ban on mixing with chlorine bleach and ammonia products, the threshold limit value for phosphoric acid mist, personal protective equipment, first aid, and handling and storage. Dilution rates and contact times are not given and are read from the product label. Repairing etched surfaces, large spills, and treating casualties are stated as the work of other parties.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    On December 19, 1987, at a state hospital in California, a patient who was helping with cleaning duties mopped a bathroom floor with a 4 percent phosphoric acid cleaning solution, then rinsed it with water. As soon as a solution of bleach and water was applied to the same floor, a gas with a sharp odor came off. The room’s exhaust fan was not working and its windows were sealed shut, so the gas spread through the whole ward and the ward was evacuated. The occupants returned about an hour and a half later, after the odor had gone, and within the next hour other patients and staff complained of nausea, stinging eyes, cough, and chest tightness. The ward was evacuated again until the following day.

    That incident was one of five similar incidents at two hospitals between October 1987 and November 1989, with at least 14 people affected, and all of them involved bleach and a phosphoric acid cleaner. The cleaner’s label did not name its active ingredient and did not warn of the danger of mixing, and its safety data sheet did not list hazardous reactions or incompatible materials. The acid bathroom cleaners on hotel and hospital housekeeping trolleys today are the same kind of product. The people who use them need to know what is in them, which surfaces they damage, and why these products must not meet bleach.

    Scope

    This chapter covers one class of product, namely liquid bathroom cleaners that are acidic and use phosphoric acid as their acid ingredient: concentration and pH, how acid dissolves scale, surfaces damaged by acid, the ban on mixing with chlorine bleach and ammonia products, personal protective equipment, first aid, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of this class. Other products can differ, so what applies in the workplace is the label and the safety data sheet of the product actually in use.

    This chapter is learning material, not a work instruction. Dilution rates, contact times, and mixing recipes are not given; all of them are read from the product label and the workplace procedure. Germ-killing power is not covered, because an acid cleaner is not a disinfectant; disinfectants are in Chapter 4 · Biology & Microbiology on disinfectants and how they work.

    How to check that the pH, the classification, and the personal protective equipment on a data sheet agree is in Chapter 26 on reading the safety data sheets of cleaning products. Labels, spills, and general first aid are in Chapter 6 · Safety on chemicals in technician work, hazardous mixtures in Chapter 25 on chemical reactivity and incompatibility, the pH of weak acids in Chapter 15 on advanced acids and bases, scale in Chapter 16 on solubility and precipitation, chemical burns in Chapter 41 · Biology & Microbiology on the skin and chemicals, and grout in Chapter 39 · Buildings & Facilities on floors and tiles. Rust, heavy scale, and cement residue are covered in Chapter 31 on rust, scale, and cement residue removers, and marble floors in Chapter 32 on crystallization and polishing of marble floors.

    Work outside the authority of housekeeping staff and building technicians: repairing stone, glaze, grout, or metal plating that acid has already eaten away, handling a large spill or a spill that has mixed with bleach, and giving treatment other than first aid. Surface repair belongs to the stone and floor care contractor, large spills belong to trained personnel or the emergency response team, and casualties are handled by a doctor or the emergency services. The choice of product is decided by the housekeeping supervisor together with the supplier.

    What the product contains: phosphoric acid and low pH

    According to the manufacturer’s safety data sheet for one product of this class, the acid bathroom cleaner is a liquid that is soluble in water and is sold ready to use. Only one ingredient is listed, namely phosphoric acid with CAS number 7664-38-2 at a concentration of 5 to 10 percent. The pH of the undiluted product is 0 to 2, and its relative density is 1.000 to 1.020. The data sheet was issued on July 26, 2024 and is valid until July 25, 2029.

    Phosphoric acid, with the formula H₃PO₄, is an inorganic acid that has three hydrogen atoms it can release, is a colorless and odorless solid in its pure form, and is often used as a solution in water. It is a weak acid. Its first ionization constant is Ka1=7.5×10−3K_{a1} = 7.5 \times 10^{-3}, while the second and third are far smaller, namely 6.2×10−86.2 \times 10^{-8} and 4.2×10−134.2 \times 10^{-13}. The word “weak” here is a chemical term for the fraction of molecules that ionize, as explained in Chapter 15 on advanced acids and bases, not a measure of hazard. At a concentration of 5 to 10 percent, the pH is already about 1 (Example 2).

    For a weak acid at a concentration of CC mol/L, the hydrogen ion concentration xx satisfies

    Ka1=x2C−x,x=−Ka1+Ka12+4Ka1C2,pH=−log⁡xK_{a1} = \frac{x^2}{C - x}, \qquad x = \frac{-K_{a1} + \sqrt{K_{a1}^2 + 4K_{a1}C}}{2}, \qquad \text{pH} = -\log x

    with xx and CC in mol/L. This formula counts only the first ionization and treats the solution as ideal, so the result is an estimate, not a substitute for measurement. The pH scale is logarithmic: for every unit it falls, the hydrogen ion concentration rises 10 times (Example 3).

    The other ingredients of the product cannot be known from that data sheet. Chemical cleaners, both acidic and alkaline, commonly also contain surfactants as wetting agents.

    Water scale and soap scum: why acid works

    Water scale is a mineral deposit, mainly calcium carbonate, that is left on a surface when hard water evaporates or is heated. How it forms is covered in Chapter 16 on solubility and precipitation. Calcium carbonate is sparingly soluble in water, with a solubility product of 8.7×10−98.7 \times 10^{-9}, but its solubility rises sharply in an acidic solution because the carbonate ion is bound by hydrogen ions:

    CaCO3(s)+H3O+(aq)⇌Ca2+(aq)+HCO3−(aq)+H2O(l),K=180\text{CaCO}_3(s) + \text{H}_3\text{O}^+(aq) \rightleftharpoons \text{Ca}^{2+}(aq) + \text{HCO}_3^-(aq) + \text{H}_2\text{O}(l), \qquad K = 180

    With enough acid, the bicarbonate ion accepts one more hydrogen ion and breaks down into water and carbon dioxide gas, as in Chapter 9 on types of reactions in water. The fine fizzing that appears when an acid cleaner touches scale is that carbon dioxide. This behavior is general for salts with basic anions, such as carbonate and hydroxide.

    Soap scum is the calcium and magnesium salts of the fatty acids in soap, which form when soap meets hard water and do not dissolve in water. How it forms is covered in Chapter 21 on surfactants, colloids, and emulsions. The carboxylate ion in soap scum is also a basic anion. In an acidic solution, that ion accepts a hydrogen ion and turns back into a fatty acid, while the calcium ion is released into the solution. The fatty acid still does not dissolve in water, so it still has to be lifted by surfactants, scrubbing, and rinsing.

    Two limits need to be remembered. Acid is used up as it reacts, so a given amount of cleaner dissolves only a given amount of scale (Example 4); heavy scale is dealt with by repeating the application according to the label, not by mixing in another product. Acid also works only on minerals, so body oils, cosmetic residue, and mold are not its targets.

    Surfaces damaged by acid

    The reaction that dissolves scale also dissolves building materials that are of the same kind as scale. Marble and limestone are made of calcium carbonate, which is why even acid rain corrodes statues and building facades made of these two stones. The following surfaces need to be recognized before an acid cleaner is used.

    SurfaceEffect of acidGuidance
    Marble and limestone, polished or notchemically etched and dissolved; the gloss is lostacid cleaners are not used; United States building preservation guidance classes them as acid-sensitive materials
    Polished granite, glazed brick and glazed terra cottaclassed as acid-sensitive by the same guidanceacid cleaners are not used
    Glazed ceramic tileacid can damage the silicates in the glazeonly acid cleaners made specifically for ceramic tile, and even those with caution
    Grout and mortar based on cement or limethe binder is dissolved by acidcontact is limited and rinsed off thoroughly; acid is in fact used to lift mortar stains from tile
    Metals: faucets, floor drains, rails, hinges, metal bucketsphosphoric acid reacts with most metals and releases flammable hydrogen gasavoid contact, do not hold the product in a metal container, rinse off splashes

    The type of stone cannot always be recognized from its appearance. That is why the guidance asks for every cleaner to be tested first in an inconspicuous spot, and warns that even a suitable acid cleaner does damage if it is left on too long or is not rinsed off adequately. For tile floors, guidance from the same agency advises wetting the floor first before any cleaner is used. The water fills the pores of the tile and keeps chemicals from soaking into the tile body, and the floor is always rinsed thoroughly afterward. The contact time for a product is read from its label.

    Damage done by acid cannot be rinsed away. Dulled marble, clouded glaze, and pitted grout need repair by other parties, as covered in Chapter 39 · Buildings & Facilities on floors and tiles and Chapter 32 on crystallization and polishing of marble floors.

    The ban on mixing with bleach

    Chlorine bleach is a solution of sodium hypochlorite in water; the household bleach in the California incidents had a concentration of 5.25 percent. When hypochlorite meets an acid, chlorine gas and water are formed:

    OCl−+Cl−+2 H+→Cl2+H2O\text{OCl}^- + \text{Cl}^- + 2\,\text{H}^+ \rightarrow \text{Cl}_2 + \text{H}_2\text{O}

    The chlorine gas then reacts with water to form hydrochloric acid and hypochlorous acid. According to the report on those incidents, a level of about 3 ppm can already cause severe irritation of the eyes and the respiratory tract, while the odor is usually not detectable until above 3.5 ppm. Severe exposure can cause pulmonary edema. The calculation of the amount of gas is in Chapter 25 on chemical reactivity and incompatibility and in Example 5.

    NIOSH, the United States occupational safety and health institute, writes that phosphoric acid must not be mixed with solutions containing bleach or ammonia. HSE, the British occupational safety authority, writes that products containing bleach that are mixed with acidic toilet cleaners or ammonia give off harmful gases, and gives workers one short rule: never mix cleaning substances.

    The California incidents show four ways in which that ban is broken unintentionally:

    1. Two products in one bucket. Acid cleaner is poured into a bucket that still holds bleach solution.
    2. One after the other on the same surface. A floor that has already been rinsed still releases gas when bleach is applied.
    3. A closed room. A dead exhaust fan and closed windows let the gas spread to other rooms.
    4. Odor used as the measure. People who returned after the odor had gone still developed symptoms; the report states that the absence of odor is not a sign of safety.

    The first hospital ended up keeping acid cleaners in a locked room and prohibiting the mixing of cleaning products. The second hospital put warning labels on all products and “do not mix” signs on the janitorial closets. In a hotel bathroom, the acid cleaner for scale and the bleach for moldy grout easily meet. The two are not used in the same job and are not poured into the same bucket or bottle.

    Health hazards, threshold limit values, and personal protective equipment

    NIOSH records the routes of entry of phosphoric acid as inhalation, ingestion, and skin and eye contact. The symptoms are irritation of the eyes, skin, and upper respiratory tract, burns of the eyes and skin, and dermatitis. For solutions above 1.6 percent, NIOSH recommends that an eyewash and a quick-drench facility be available. The 5 to 10 percent concentration of products in this class is above that figure (Example 3). Chemical burns and dermatitis are explained in Chapter 41 · Biology & Microbiology on the skin and chemicals.

    Threshold limit value (Indonesian nilai ambang batas, NAB) is the time-weighted average concentration that workers can accept without it causing disease or health problems, for a time not exceeding 8 hours a day or 40 hours a week. Permitted short-term exposure (Indonesian pajanan singkat diperkenankan, PSD) is the concentration in air that must not be exceeded for a short exposure of no more than 15 minutes, at most 4 times in one working day. Permenaker (Minister of Manpower Regulation) 5/2018 sets the NAB for phosphoric acid at 1 mg/m³ and the PSD at 3 mg/m³, with the note irritation of the upper respiratory tract, eyes, and skin. As of November 2026 that regulation is listed as in force on JDIH Kemnaker, the ministry’s legal documentation site. These figures concern phosphoric acid suspended in air as a mist, for example from a spray bottle in a bathroom without ventilation (Example 6).

    The selection of personal protective equipment is covered in Chapter 5 · Safety on personal protective equipment. HSE guidance for cleaning substances in hospitality:

    • The protective clothing provided is always worn when handling cleaning substances.
    • Eye protection suitable for splashes, for example goggles or a visor, is worn if there is any chance of splashing and when cleaning at eye level or above, such as shower walls.
    • Rubber gloves are checked for holes, tears, and thin patches, and replaced if faulty. Latex gloves are avoided because they can cause reactions.
    • Cleaning substances are used only in well-ventilated places, and mechanical ventilation must be switched on and working.
    • Where tap water is not available for rinsing the eyes, at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers is provided.

    The glove material and the need for respiratory protection are read from the product’s data sheet. If the data sheet of a product with pH 0 to 2 lists no hazard to the eyes and skin or states that personal protective equipment is not required, its content is checked by the method in Chapter 26 on reading the safety data sheets of cleaning products and the supplier is asked before the product is used.

    First aid

    First aid follows the product’s data sheet and the workplace procedure. NIOSH guidance for phosphoric acid and HSE guidance for chemical injuries:

    1. Eyes. The eyes are immediately washed with large amounts of water while occasionally lifting the upper and lower lids, then the casualty is taken to medical attention immediately. HSE asks for the eye to be flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then for the casualty to be sent to hospital.
    2. Skin. The skin is immediately flushed with water. If the liquid has soaked through clothing, the clothing is removed immediately and the skin is flushed, then the casualty gets medical attention. For chemical burns, HSE asks for the affected area to be flooded with water for 20 minutes, for contaminated clothing that is not stuck to the skin to be removed, and for the first aider to avoid being contaminated as well.
    3. Swallowed. The casualty is taken to medical attention immediately.
    4. Inhaled. The casualty is moved to fresh air at once, kept warm and at rest, and gets medical attention as soon as possible. Artificial respiration is given by a trained person if breathing has stopped.

    The label or the product’s data sheet is taken to the doctor, and what happens next is the decision of the medical personnel.

    Handling and storage

    The manufacturer’s safety data sheet for one product of this class gives a storage temperature of 0 to 50 °C and names bases, metals, and organic materials as incompatible materials. Chlorine bleach is basic, as in the example data sheet in Chapter 6 · Safety on chemicals in technician work, so it is stored in a place separate from acid cleaners.

    HSE gives guidance on storing and handling cleaning substances in hospitality:

    • Substances are kept in their original labeled containers. If they are decanted, the new container is made of a suitable material, is clean, and is clearly marked with the instructions for use and the hazards.
    • Cleaning substances are never transferred into food or drink containers.
    • The store is away from heat, sunlight, foodstuffs, and members of the public, especially children. All containers have lids, and the manufacturer’s storage instructions are checked because some products need to be stored separately.
    • Staff are informed, trained, and supervised. Handing out data sheets alone is not enough.

    Spray bottles and buckets for acid cleaner are marked and are not used interchangeably with bleach. After the California incidents, CDC advised that the use of such chemicals be restricted to trained employees where constant supervision is not possible. Small spills are handled according to Chapter 6 · Safety on chemicals in technician work, and leftover product and empty containers according to the label and Chapter 35 · Water & Water Treatment on B3 waste.

    Worked example

    The figures in the examples below are practice figures, unless their origin is stated. A relative density of 1.010 is used as the midpoint of the range on the data sheet, and the molar volume of a gas, 24.5 L/mol, applies at 25 °C and 1 atm.

    Example 1: mass and moles of acid per liter. One liter of product has a mass of 1.010×1,000=1,0101.010 \times 1{,}000 = 1{,}010 g. At 5 percent, the phosphoric acid is 0.05×1,010=50.50.05 \times 1{,}010 = 50.5 g, and at 10 percent it is 0.10×1,010=1010.10 \times 1{,}010 = 101 g. With a molar mass of 98.00 g/mol, the concentration is 50.5/98.00=0.51550.5/98.00 = 0.515 mol/L to 101/98.00=1.03101/98.00 = 1.03 mol/L. A 5 L jerry can holds 5×50.5=252.55 \times 50.5 = 252.5 g to 5×101=5055 \times 101 = 505 g of phosphoric acid.

    Example 2: whether the pH fits the concentration. For C=0.515C = 0.515 mol/L: x=(−0.0075+0.00752+4×0.0075×0.515)/2=0.0585x = (-0.0075 + \sqrt{0.0075^2 + 4 \times 0.0075 \times 0.515})/2 = 0.0585 mol/L, so pH =−log⁡0.0585=1.23= -\log 0.0585 = 1.23. For C=1.03C = 1.03 mol/L: x=0.0842x = 0.0842 mol/L and pH =1.07= 1.07. Both results lie within the pH 0 to 2 range on the data sheet, so the concentration and the pH in that document agree with each other. Only about 0.0585/0.515=110.0585/0.515 = 11 percent of the acid molecules are ionized.

    Example 3: compared with two benchmarks. Against the NIOSH figure of 1.6 percent, the product concentration is 5/1.6=3.1255/1.6 = 3.125 to 10/1.6=6.2510/1.6 = 6.25 times higher, so eyewash and body-drench facilities are relevant for this product. Against water at pH 7, a cleaner at pH 1 contains 10−1/10−7=10610^{-1}/10^{-7} = 10^{6} times, that is one million times, more hydrogen ions.

    Example 4: the scale that 100 mL of product can dissolve. At 5 percent, 100 mL of product contains 0.100×0.515=0.05150.100 \times 0.515 = 0.0515 mol of phosphoric acid. The second hydrogen ion of phosphoric acid is weaker than carbonic acid, so only the first hydrogen ion is counted: CaCO3+2 H3PO4→Ca2++2 H2PO4−+H2O+CO2\text{CaCO}_3 + 2\,\text{H}_3\text{PO}_4 \rightarrow \text{Ca}^{2+} + 2\,\text{H}_2\text{PO}_4^- + \text{H}_2\text{O} + \text{CO}_2. The calcium carbonate that can react is at most 0.0515/2=0.02580.0515/2 = 0.0258 mol, that is 0.0258×100.09=2.580.0258 \times 100.09 = 2.58 g, and the carbon dioxide gas is 0.0258×24.5=0.630.0258 \times 24.5 = 0.63 L. More scale than that is not used up in one application; the way out is to repeat according to the label, not to add another product.

    Example 5: upper limit of chlorine in one incident. In one of the California incidents, about 0.5 L of bleach was mixed with 1 L of 4 percent phosphoric acid cleaner. If percent is read as grams per 100 mL, the 5.25 percent bleach contains 0.5×52.5=26.250.5 \times 52.5 = 26.25 g of sodium hypochlorite, that is 26.25/74.44=0.35326.25/74.44 = 0.353 mol, and the cleaner contains 40/98.00=0.40840/98.00 = 0.408 mol of phosphoric acid. The reaction needs two hydrogen ions for each chlorine molecule. With the first hydrogen ion alone, the acid is the limiting reactant and the chlorine is at most 0.408/2=0.2040.408/2 = 0.204 mol, that is 0.204×24.5=5.00.204 \times 24.5 = 5.0 L. In a ward bathroom measuring 4 m by 3 m by 2.8 m, that is 33.6 m³ or 33,600 L, the level is 5.0/33,600×106=1495.0/33{,}600 \times 10^{6} = 149 ppm if evenly mixed. That figure is about 50 times the 3 ppm level that already causes severe irritation. This is an upper limit, but just 2 percent of it already equals 3 ppm.

    Example 6: mist and the PSD. A hotel guest bathroom measuring 2.0 m by 1.8 m by 2.4 m has a volume of 2.0×1.8×2.4=8.642.0 \times 1.8 \times 2.4 = 8.64 m³. The PSD of 3 mg/m³ is reached with 3×8.64=25.923 \times 8.64 = 25.92 mg of phosphoric acid in the air. At 10 percent, that is equivalent to 25.92/0.10=259.225.92/0.10 = 259.2 mg of product, that is 0.2592/1.010=0.260.2592/1.010 = 0.26 mL. A quarter of a milliliter of product suspended as mist in a bathroom without ventilation already reaches the PSD, so the ventilation is switched on before the spray bottle is used.

    Stop conditions

    1. A sharp odor like bleach is noticed, or the eyes and throat sting, while an acid cleaner is in use: stop work, leave the room, and clear the surrounding rooms. Do not re-enter only because the odor has gone. The supervisor calls the building emergency response team or the fire department, and anyone short of breath is taken to the emergency services.
    2. Chlorine bleach or an ammonia product has already been used on the same surface, or the buckets and bottles are unlabeled: do not use the acid cleaner. The housekeeping supervisor decides the work sequence and the containers to be used.
    3. The surface is marble, limestone, polished granite, or a stone of unknown type: do not use the acid cleaner. The supervisor contacts the material supplier or the stone care contractor.
    4. A test in an inconspicuous spot leaves the surface dull, discolored, or fizzing continuously: stop and rinse. Repair of the surface is handed to the stone and floor care contractor.
    5. Metal near the work is fizzing or changing color, or the acid cleaner is in a metal container: stop, rinse, and report to the supervisor; metal containers are not used for this product.
    6. A splash gets into the eyes, the skin feels burned, the product is swallowed, or someone is short of breath after inhaling mist: give first aid and take the casualty to a doctor or the emergency services.
    7. A spill is larger than the local spill kit can handle, or a spill has reached bleach: clear the room and hand over to trained personnel or the emergency response team.
    8. The label is missing, the safety data sheet is absent or past its validity date, or its content does not fit the product’s pH: the product is not used until the supervisor has an explanation from the supplier.
    9. The bathroom ventilation is dead and the windows cannot be opened: postpone the work until a building technician restores the ventilation.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    The floor has been rinsed, so bleach can go straight on.

    Why is it wrong?

    In the California incidents, a floor that had already been rinsed still released chlorine gas when bleach was applied. The two products are not used in the same job.

    Common misconception

    If the odor has gone, the room is safe.

    Why is it wrong?

    The odor of chlorine is usually not detectable until above a level that already irritates, and people who returned after the odor had gone still developed symptoms. A room is declared safe by authorized personnel after sufficient air exchange.

    Common misconception

    Phosphoric acid is a weak acid, so it is not dangerous.

    Why is it wrong?

    Weak means that only a fraction of its molecules ionize. At 5 to 10 percent its pH is about 1, and NIOSH records burns of the eyes and skin.

    Common misconception

    Ready to use means safe without protection.

    Why is it wrong?

    Ready to use only means that the product does not need to be diluted. Its acid concentration is still above the 1.6 percent figure at which NIOSH recommends an eyewash.

    Common misconception

    The longer it is left on, the cleaner it gets.

    Why is it wrong?

    Acid that is left on too long or not rinsed off thoroughly damages grout, glaze, and metal. Contact time follows the label.

    Chapter 26 on reading the safety data sheets of cleaning products gives the method for checking the data sheet on which this chapter rests. Chapter 25 on chemical reactivity and incompatibility contains the segregation of materials and the chlorine gas calculation. Chapter 31 on rust, scale, and cement residue removers continues to acids for heavier work.

    Exercises and worked solutions

    The figures in the problems are for practice.

    Try to answer first, then open the worked solution.

    1. A 750 mL spray bottle is filled with a product containing 10 percent phosphoric acid with a relative density of 1.010. How many grams of phosphoric acid does it hold?

      Check my answer
      See the worked solution

      The mass of product is 750×1.010=757.5750 \times 1.010 = 757.5 g, so the phosphoric acid is 0.10×757.5=75.750.10 \times 757.5 = 75.75 g. Even a small bottle holds tens of grams of acid, so the bottle is labeled like the original container.

    2. The pH of a cleaning solution falls from 3 to 1. By how many times does its hydrogen ion concentration rise?

      Check my answer
      See the worked solution

      A pH difference of 2 units means the hydrogen ion concentration rises 102=10010^{2} = 100 times. The pH scale is logarithmic, so a small difference in the number stands for a large change in concentration.

    3. A worker mops a bathroom floor with acid cleaner, rinses it once, and is then about to use bleach on the moldy grout. What is wrong?

      Check my answer
      See the worked solution

      A floor that has been rinsed can still hold acid residue, so the bleach can release chlorine gas as in the opening case. The two products are not used in the same job, and the work sequence is decided by the supervisor.

    4. A bathroom measuring 3 m by 2 m by 2.5 m has no ventilation. How many milligrams of phosphoric acid in the air equal the NAB, and how many milligrams of 5 percent product contain that amount?

      Check my answer
      See the worked solution

      The room volume is 3×2×2.5=153 \times 2 \times 2.5 = 15 m³, so the NAB of 1 mg/m³ is equaled by 15 mg of phosphoric acid in the air. At 5 percent that is equivalent to 15/0.05=30015/0.05 = 300 mg of product, less than one third of a milliliter, so the ventilation must be working before the spray bottle is used.

    5. A suite bathroom has a ceramic tile floor and a marble vanity top. Where may an acid cleaner be considered, and under what conditions?

      Check my answer
      See the worked solution

      An acid cleaner is not used on the marble top because marble is acid-sensitive and will be chemically etched. On the ceramic tile, the only thing that may be considered is an acid cleaner made for tile, after a test in an inconspicuous spot, on a floor that has been wetted first, and rinsed off thoroughly.

    6. After a mixing incident, the chlorine odor in the corridor disappears within half an hour and the staff want to go back to work. What does the supervisor decide?

      Check my answer
      See the worked solution

      The staff may not return yet, because the absence of odor is not a sign of safety and in the opening case the people who returned after the odor had gone still developed symptoms. The supervisor waits for the all-clear from the emergency response team, and anyone with symptoms is examined by a doctor.

    References

    External sources

    • Epidemiologic Notes and Reports Chlorine Gas Toxicity from Mixture of Bleach with Other Cleaning Products -- Californiacdc.gov
    • NIOSH Pocket Guide to Chemical Hazards - Phosphoric acidcdc.gov
    • First Aid Procedures for Chemical Hazardscdc.gov
    • Safe use of cleaning substances in the hospitality industryhse.gov.uk
    • Basic advice on first aid at workhse.gov.uk
    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
    • Chemistry 2eopenstax.org
    • Preservation Brief 1: Assessing Cleaning and Water-Repellent Treatments for Historic Masonry Buildingsnps.gov
    • Preservation Briefs 40: Preserving Historic Ceramic Tile Floorsnps.gov

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Acid bathroom cleaners: phosphoric acid and low pH, soap scum and water scale, surfaces damaged by acid, the ban on mixing with bleach, personal protective equipment, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/pembersih-kamar-mandi-asam-asam-fosfat-dan-ph-rendah-kerak-sabun-dan-kerak-air-permukaan-yang-rusak-oleh-asam-larangan-mencampur-dengan-pemutih-alat-pelindung-diri-serta-penanganan-dan-penyimpanan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A 750 mL spray bottle is filled with a product containing 10 percent phosphoric acid with a relative density of 1.010. How many grams of phosphoric acid does it hold?

    2

    The pH of a cleaning solution falls from 3 to 1. By how many times does its hydrogen ion concentration rise?

    3

    A worker mops a bathroom floor with acid cleaner, rinses it once, and is then about to use bleach on the moldy grout. What is wrong?

    Self-assessment progress0%

    Nearby chapters