By Kurnia · Published November 15, 2026 · Version 1 · 21 min read
Marble floor crystallization and polishing
oxalic acid powder, the reaction with calcium carbonate, polishing slurry and the machine, floor care products, dust and splashes, and handling and storage
Housekeeping attendants pour an odorless white powder onto the marble floor of a hotel lobby, a cloud of dust rises, and one of them rubs an eye with a powder-covered glove. According to the manufacturer’s safety data sheet for one product of this class, the powder contains 60 to 100 percent oxalic acid plus aluminum oxide, with a pH of 0.5 to 2.5 in a 1 percent solution. This chapter covers the chemicals used to restore the shine of marble floors: marble as soft, acid-sensitive calcium carbonate, the contents and classification of oxalic acid powder, its reaction with calcium carbonate to form sparingly soluble calcium oxalate, abrasives, silica polishing slurry, and machine hazards on a wet floor, a slightly alkaline liquid floor care product, threshold limit values for dust, first aid, the prohibition on mixing with chlorine bleach, and handling and storage. Dosage, pads, and rubbing time are not given and are referred to the product label; grinding and repairing stone are stated to be work for a stone restoration contractor.
This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.
The cream marble floor in a hotel lobby looks dull along the path between the entrance and the reception desk. Close to midnight, two housekeeping attendants bring a floor polishing machine and a pail of white powder. One of them pours the powder from waist height, and a cloud of fine dust rises to face level. Both cough, then one rubs an eye with a glove that still has powder on it and stops working because the eye stings.
The powder is odorless, so nobody takes its dust to be dangerous. The manufacturer’s safety data sheet for one product of this class states that it contains 60 to 100 percent oxalic acid and 10 to 30 percent aluminum oxide, with a pH of 0.5 to 2.5 in a 1 percent solution, and classifies it as harmful if swallowed and as causing serious eye damage. The attendants need to know how the powder acts on marble, why its dust and splashes are dangerous, and which work is not theirs to do.
Scope
This chapter covers the chemicals used to restore the shine of marble floors: oxalic acid powder with an abrasive, silica polishing slurry, and a liquid floor care product. The product data come from the manufacturer’s safety data sheets for three products, one from each class, and apply to those products alone; other products may differ in contents and concentration.
This chapter is learning material, not a work instruction. The amount of powder per square meter, the amount of water, the type of pad, and the rubbing time are not written in the data sheets of those three products, so this chapter does not give those figures. Those figures are taken only from the product label and the supplier’s instructions, and the attendants who do the work must already have been trained for that product and that machine.
How to read a data sheet is covered in Chapter 26 on reading safety data sheets for cleaning products. Oxalic acid as a rust and scale remover is in Chapter 31 on removers for rust, scale, and cement residue, acid bathroom cleaners are in Chapter 30, and abrasive creams are in Chapter 33 on abrasive polishing cream. Hazardous mixtures are covered in Chapter 25 on chemical reactivity, labels and spills in Chapter 6 · Safety on chemicals in the technician’s work, personal protective equipment in Chapter 5 · Safety, and slippery floors in Chapter 39 · Buildings & Facilities on floors and tiles.
Work outside the authority of housekeeping attendants and hotel technicians: grinding or leveling marble, patching cracks and holes, replacing loose or hollow-sounding tiles, and handling large spills of powder. Stone work belongs to a stone restoration contractor, and large spills belong to trained spill responders and the person responsible for occupational safety and health (K3).
Marble: a soft, acid-sensitive calcareous stone
Marble is a metamorphic rock formed from limestone and made up mainly of calcite, that is, calcium carbonate, CaCO₃. NIOSH notes that calcium carbonate occurs in nature as limestone, chalk, marble, and calcite, and that this material is incompatible with acids. That incompatibility is an ordinary chemical reaction: an acid reacts with a carbonate and produces a calcium salt, water, and carbon dioxide gas.
The first property: marble is acid-sensitive. The United States National Park Service, in its guidance on cleaning historic masonry buildings, writes that acidic cleaners can be extremely damaging to acid-sensitive stones such as marble and limestone because they etch and dissolve them. Etching is the dull mark left behind when an acid dissolves a little of the stone surface.
The second property: marble is soft. The Mohs hardness scale is a scale of the relative hardness of minerals from 1 to 10, built by scratching one material against another: the harder material scratches the softer one. On that scale calcite is 3, a glass plate 5.5, a steel nail 6.5, quartz 7, and corundum 9. Silica is found in most rocks, sand, and clay, and quartz is one of its crystalline forms. Grains of sand carried in on shoe soles are therefore harder than marble and can scratch it little by little.
Fine scratches make the floor look dull: a flat surface reflects light in one direction and so looks shiny, whereas a surface full of scratches reflects it in many directions.
Oxalic acid powder: contents, pH, and classification
Oxalic acid is a diprotic organic acid with the formula H₂C₂O₄, which in its dihydrate form binds two molecules of water of crystallization. According to NIOSH, it is a colorless, odorless powder or granular solid, with a solubility in water of 14 percent. The manufacturer’s safety data sheet for one crystallization powder of this class contains the following data.
| Item | Data sheet content |
|---|---|
| Intended use | floor care product for industrial and professional use, sold ready to use |
| Composition | oxalic acid (CAS 144-62-7) 60 to 100 percent; aluminum oxide (CAS 1344-28-1) 10 to 30 percent |
| Form | opaque white powder, odorless, slightly soluble in water |
| pH | 0.5 to 2.5 in a 1 percent solution |
| Classification | acute oral toxicity category 4 and serious eye damage category 1, with the signal word “Danger” |
| Incompatible materials | bases |
| Packaging | suitable: plastic; unsuitable: aluminum and mild steel |
| Storage temperature | -10 to 50 °C |
| Document validity | issued June 6, 2025, valid until June 5, 2030 |
A concentration range is read as limits, not as an exact figure. The pH explains the classification: even a 1 percent solution has a pH of 2.5 at most, and Example 3 shows that this figure agrees with the first ionization constant of oxalic acid, , which is about 3,300 times the constant of acetic acid, . Oxalic acid is indeed a weak acid by the definition in Chapter 15 on advanced acid-base chemistry, but at working concentration its solution is strongly acidic.
Aluminum oxide is the abrasive in the powder. NIOSH records corundum as natural aluminum oxide, and corundum is 9 on the Mohs scale, far above calcite.
The reaction of oxalic acid with calcium carbonate
In the reaction of hydrochloric acid with calcium carbonate, the salt formed is calcium chloride, which dissolves and is rinsed away. With oxalic acid the equation is similar:
One mole of oxalic acid consumes one mole of calcium carbonate and releases one mole of carbon dioxide gas. The difference lies in the salt. Calcium oxalate is very sparingly soluble: the solubility product of calcium oxalate monohydrate at 25 °C is , the same order of magnitude as calcium carbonate itself, . Part of the calcium released from the stone therefore precipitates again as calcium oxalate crystals on the stone surface and in the slurry.
In the trade this work is called crystallization, that is, restoring the shine of a calcareous stone floor with an acidic chemical that a floor polishing machine rubs in until it reacts with the stone surface. That reaction occurs only on stone that contains calcium carbonate, such as marble and limestone. Stone that contains no carbonate does not react in this way, so the type of stone must be known first.
A laboratory study in the United States funded by the National Park Service tested marble treated with an ammonium oxalate solution. The treatment produced a uniform coating of small calcium oxalate crystals that slowed the dissolution of marble by acid, but the rate of acid attack fell only by about half. The material tested was not a floor powder, so the figure cannot be carried over directly to a hotel floor. What can be taken from it is the direction: an oxalate layer is not a shield, and a floor that has been crystallized remains sensitive to acid.
The shine after this work is the combined result of reaction and rubbing: the acid dissolves the dull top layer, then the abrasive and the machine pad level the fine scratches. The share of each differs by product, stone, and machine, so this chapter gives no figures for gloss or durability. Every pass consumes a little stone, and Example 2 calculates its upper limit, a few micrometers per pass. Adding powder and rubbing longer adds to the stone lost.
Abrasives, polishing slurry, and the machine
Polishing slurry is a mixture of fine abrasive with water and chemicals that is rubbed between the machine pad and the floor. The manufacturer’s safety data sheet for one marble polishing slurry of this class describes it as a white cream sold ready to use. Its composition is silica with the CAS number of quartz (14808-60-7) 13 percent, oxalic acid 2.2 percent, water 81 percent, and one component at 3.8 percent that is written as an abbreviation without a CAS number; its pH is 2.45, with no statement of the concentration at which it was measured. Compared with the powder, the acid in this slurry is far more dilute and the abrasive is different: quartz is 7 on the Mohs scale, below corundum but still far above calcite.
An abrasive harder than the stone cuts the stone, not only the dirt on it. The National Park Service writes that abrasives do not differentiate between the dirt and the stone, and that abrasion of polished surfaces removes the polished finish. In polishing work that cutting is deliberate and is controlled by using very fine grains. Sand left on the floor turns polishing into scratching, so the floor is cleared of sand first. The data sheet of the polishing slurry above also asks for the product to be tested first when the type of stone is unknown.
A floor polishing machine is an electric machine that turns a pad on a wet floor, and three of its hazards come from the machine:
- A wet floor covered in slurry is slippery. The United Kingdom’s HSE notes that the cleaning process itself often introduces slip and trip hazards, namely wet floors and trailing cables. Its advice: work during quiet hours and in sections so that a dry path remains, and restrict access to the wet floor.
- Electricity meets water. The cable, plug, and connections are checked before the machine is used; residual current protection is in Chapter 22 · Electrical & Control on RCDs.
- The turning pad throws splashes. Those splashes are acidic slurry, so eye or face protection is also worn by anyone standing near the machine.
Liquid floor care product
The manufacturer’s safety data sheet for one floor care liquid of this class describes it as a liquid, opaque, light yellow, with a faint odor, and soluble in water. Its pH is 8.3 to 8.9 for the undiluted product and 7.0 to 9.0 for the use solution, its relative density is 1.032 to 1.036, and its use concentration is 30 to 100 percent product. Its storage temperature is -15 to 50 °C, and the document was issued on April 18, 2024 and is valid until April 17, 2029. That data sheet lists no hazardous ingredients in its composition and gives its intended use as a floor care product.
Two things deserve attention. First, its pH is slightly alkaline and close to neutral, the opposite of the acidic powder and slurry. The National Park Service guidance above places marble, whether polished or not, among the materials cleaned with alkaline cleaners and not with acidic cleaners. Second, this liquid is diluted, whereas the powder and the slurry are sold ready to use. The range of 30 to 100 percent is very wide, so the use concentration is taken from the label and is not guessed (Example 5).
Because its pH lies in the opposite direction, this liquid is not mixed with the acidic powder or slurry in one bucket or one machine tank: acid and base neutralize each other, so both lose their action. Buckets, tanks, and pads are rinsed with clean water between the two products.
Dust and splashes
The greatest hazard of crystallization powder lies in the dust when the powder is poured and in the splashes of slurry when the machine turns. NIOSH records the exposure routes of oxalic acid as inhalation, ingestion, and skin and eye contact. Its symptoms range from irritation of the eyes, skin, and mucous membranes and eye burns through to kidney damage, and its target organs are the eyes, skin, respiratory system, and kidneys.
The threshold limit value (Indonesian nilai ambang batas, NAB) is the time-weighted average concentration that workers can accept without disease or health disorders, for work not exceeding 8 hours a day or 40 hours a week. The permitted short-term exposure (Indonesian pajanan singkat diperkenankan, PSD) is the concentration that must not be exceeded during a short exposure of no more than 15 minutes. Permenaker (Minister of Manpower Regulation) 5/2018 sets the NAB of oxalic acid at 1 mg/m³ and its PSD at 2 mg/m³, the NAB of aluminum oxide at 10 mg/m³, and the NAB of quartz at 0.025 mg/m³; as of November 2026 JDIH Kemnaker (the Ministry of Manpower’s legal documentation network) lists this regulation as in force. The NIOSH figures for oxalic acid are the same, namely 1 mg/m³ as a time-weighted average and 2 mg/m³ short term. Example 4 shows that a tenth of a gram of powder suspended evenly is enough to reach the NAB in a 60 m³ room.
Polishing slurry brings a different dust hazard: when its residue dries and is then swept, fine quartz can be raised into the air. HSE notes that crystalline silica dust fine enough to be breathed deep into the lungs can cause silicosis, chronic obstructive pulmonary disease, and lung cancer, and that polishing is among the activities that create that dust. Dust must not be dry swept; it is cleaned up with a vacuum of dust class M or H or by wet cleaning. Marble itself contains up to 5 percent crystalline silica and may contain more when it has silica veins, so grinding dry marble is dusty work that lies outside this chapter.
Control follows the order in Chapter 5 · Safety on personal protective equipment: dust is reduced at the source first, and only then is the person protected. The powder is poured close to the floor surface, not from a height, and the pail is closed again. The powder’s data sheet asks that dust not be breathed, that ventilation be adequate, and that eye or face protection be worn. NIOSH asks that skin and eye contact be prevented, that contaminated skin be washed, that wet or contaminated clothing be removed, and that an eyewash be provided. Respiratory protection is selected by the person responsible for K3 from the results of an assessment.
First aid for oxalic acid according to NIOSH is as follows.
- Eyes: immediately wash with large amounts of water while occasionally lifting the upper and lower lids, and get medical attention immediately.
- Skin: promptly flush the contaminated skin with water. If the material penetrates the clothing, remove that clothing and flush the skin. If irritation persists after washing, get medical attention.
- Large amounts breathed in: move the person to fresh air at once, keep the person warm and at rest, and get medical attention as soon as possible. If breathing has stopped, a trained first aider gives artificial respiration and the emergency services are called.
- Swallowed: get medical attention immediately.
This chapter gives no other medical instructions. The product label or data sheet is taken along to the emergency services or the doctor.
Handling and storage
The powder’s data sheet asks that the product be stored in a labeled, tightly closed container, that hands be washed thoroughly after handling, and that people not eat, drink, or smoke while working. The polishing slurry’s data sheet asks for a dry, ventilated storage room with containers always closed when not in use.
Containers and metals. The suitable packaging for the powder is plastic, whereas aluminum and mild steel are unsuitable. The powder is therefore not transferred into metal containers, and the metal parts of the machine that the slurry touches are rinsed after work. Empty containers are not reused; contents and containers are disposed of at an approved waste disposal site, as discussed in Chapter 35 · Water & Water Treatment on B3 waste.
Segregation. The powder is kept away from bases according to its data sheet, and NIOSH names strong oxidizers, silver compounds, strong alkalis, and chlorites as materials incompatible with oxalic acid. The acidic powder and slurry are not stored on the same shelf or in the same tray as chlorine bleach and alkaline products.
The prohibition on mixing with bleach. Acid must not be mixed with chlorine bleach. The CDC writes that household chlorine bleach can release chlorine gas if it is mixed with certain other cleaning products, and asks that cleaners not be mixed. That danger arises when a floor that has just been disinfected with bleach is crystallized straight away, or when a bucket that held bleach is used for acidic slurry without being rinsed.
Spilled powder is not dry swept, because sweeping raises its dust. The powder’s data sheet asks that people be kept away from the spill and that clean-up be carried out only by trained personnel.
Worked example
The figures in the examples below are practice figures, unless their origin is stated.
Example 1: how much stone the acid consumes. The molar mass of anhydrous oxalic acid is 90.04 g/mol and that of calcium carbonate is 100.1 g/mol. One hundred grams of anhydrous oxalic acid is mol. The reaction ratio is one to one, so the calcium carbonate consumed is g. The carbon dioxide gas released is also 1.11 mol; at 25 °C, with the molar volume of 24.5 L/mol from Chapter 11 on gas stoichiometry, its volume is L.
Example 2: thickness of stone lost in one pass. Suppose 20 g of powder is used on 1 m² of floor and its oxalic acid content is 80 percent, that is, 16 g. That amount is mol, equivalent to g of calcium carbonate. With a calcium carbonate density of 2.7 g/cm³, the lower end of the NIOSH range, its volume is cm³. One square meter is 10,000 cm², so the thickness is cm, that is, 6.6 micrometers. This is an upper limit, because part of the acid is rinsed away before it reacts; a hundred passes mean at most 0.66 mm of stone.
Example 3: pH of a 1 percent solution. A 1 percent solution of anhydrous oxalic acid contains 10 g/L, that is, mol/L. With the first ionization constant and the second ionization neglected, the hydrogen ion concentration satisfies , so that
The result is mol/L and . This figure lies within the range of 0.5 to 2.5 that the powder’s data sheet gives for a 1 percent solution. The symbol is the initial acid concentration and the hydrogen ion concentration, both in mol/L.
Example 4: a little dust, already at the limit. A work room of 5 m by 4 m by 3 m has a volume of 60 m³. At the NAB of 1 mg/m³, the oxalic acid suspended evenly in that room is 60 mg. If the powder contains 60 percent oxalic acid, the lower end of its data sheet range, that equals mg of powder. The 8-hour average alone is not enough: an exposure of 3 mg/m³ for 15 minutes with no other exposure gives an average of mg/m³, far below the NAB, even though 3 mg/m³ already exceeds the PSD of 2 mg/m³.
Example 5: contents of a bucket of floor care liquid. The label of a floor care liquid sets the use concentration at 30 percent, the lower end of its data sheet range. This example calculates it by volume. For 10 L of solution, L of product and L of water are needed. With a relative density of 1.032 to 1.036, the mass of 3 L of product is kg to kg.
Example 6: contents of 500 g of polishing slurry. From the slurry composition above, 500 g of slurry contains g of silica, g of oxalic acid, g of the abbreviated component, and g of water; the total is 500 g. If the slurry is left to dry, what remains is g of solids, and silica is percent of that. For that reason slurry residue is picked up while it is still wet. Its acid content is 2.2 percent, whereas the powder contains at least 60 percent, that is, times more concentrated.
Stop conditions
- Powder dust is seen hanging in the air, or someone coughs or has stinging eyes: stop pouring, leave the area, and let the air change. The housekeeping supervisor and the person responsible for K3 decide how the work proceeds next.
- Powder or slurry gets into an eye: immediately wash with large amounts of water and get medical attention immediately. A coworker stops the machine and calls for help.
- Powder or slurry is swallowed, or someone is short of breath after breathing dust: contact the emergency services or a doctor and take the product label along.
- The type of stone is unknown, the stone turns out not to be marble or limestone, or a test in a hidden spot leaves blotches, pits, or a changed color: do not continue. The stone supplier or a stone restoration contractor assesses it.
- The floor is cracked, pitted, hollow-sounding, lifted, or dished so that it needs grinding: this is work for a stone restoration contractor.
- The floor, bucket, or machine tank has just been used for chlorine bleach or another product, or there is an order to mix products: do not start. Rinse with clean water first and report to the supervisor.
- A large amount of powder is spilled, for example a whole pail tips over: do not dry sweep it. Close off the area and hand over to trained spill responders and the person responsible for K3.
- The machine cable’s insulation is damaged, the plug or a connection is wet, the residual current device trips, or water gets into the motor housing: unplug the machine from the supply if it is safe to do so and hand it over to an electrical technician.
- A container has no label, or the safety data sheet is not available or is past its validity date: do not use it. The purchasing department requests a valid document from the supplier.
- The area cannot be closed to guests while the floor is wet: postpone the work until the supervisor sets a time and barriers.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
Crystallization makes a glass-like protective layer on top of the marble.
Why is it wrong?
The reaction turns a little of the stone surface into calcium oxalate. In a laboratory test, an oxalate layer reduced the rate of acid attack only by about half, so the floor remains sensitive to acid.
Common misconception
The powder has no odor, so its dust is harmless.
Why is it wrong?
Oxalic acid is indeed odorless. Its NAB is 1 mg/m³, and 100 mg of suspended powder is already enough to reach it in a 60 m³ room.
Common misconception
Oxalic acid is a weak acid, so it is safe for the eyes.
Why is it wrong?
A 1 percent solution of the powder has a pH of 0.5 to 2.5, and its data sheet classifies it as serious eye damage category 1. The word weak describes the ionization equilibrium, not the hazard.
Common misconception
The more powder and the longer the rubbing, the shinier the floor.
Why is it wrong?
Every pass consumes stone: one hundred grams of acid consumes about 111 g of calcium carbonate. The amount and the rubbing time follow the label.
Common misconception
Every stone floor can be crystallized.
Why is it wrong?
The reaction needs calcium carbonate. Unknown stone is tested and assessed first by the stone supplier or a contractor.
Links to other chapters
Chapter 31 on removers for rust, scale, and cement residue uses oxalic acid to dissolve rust; this chapter uses it on calcareous stone. Chapter 33 on abrasive polishing cream covers quartz as an abrasive on metals and other hard surfaces. The equilibrium calculation in Example 3 rests on Chapter 15 on advanced acid-base chemistry and the solubility product on Chapter 16 on solubility and precipitation. Silica dust from grinding stone is covered in Chapter 18 · Safety on asbestos and hazardous materials during renovation.
Exercises and worked solutions
The figures in the questions are for practice.
Try to answer first, then open the worked solution.
A quantity of 250 g of powder with an anhydrous oxalic acid content of 80 percent reacts completely with marble. How many grams of calcium carbonate are consumed and how many liters of carbon dioxide are released at 25 °C?
Check my answer
See the worked solution
The oxalic acid is g, that is, mol. The reaction is one to one, so the calcium carbonate consumed is g and the carbon dioxide released is L.
Why does part of the calcium from the marble precipitate again in work with oxalic acid? Calculate the molar solubility of calcium oxalate monohydrate from its solubility product.
Check my answer
See the worked solution
Calcium chloride is soluble, whereas calcium oxalate is very sparingly soluble, so part of the calcium precipitates again. Its molar solubility is mol/L, and with a molar mass of 146.1 g/mol that is only g/L, about 6.4 mg per liter.
An attendant rubs an eye with a powder-covered glove and the eye stings. What is done, and why is the work not continued?
Check my answer
See the worked solution
The eye is immediately washed with large amounts of water while the lids are occasionally lifted, then the attendant is taken for medical attention immediately, because the powder is classified as causing serious eye damage. The work stops until the supervisor and the person responsible for K3 change the pouring method that created the dust.
A room is 8 m by 6 m by 3 m. How many milligrams of oxalic acid are suspended evenly at the NAB? If the concentration near the machine is 2.5 mg/m³ for 20 minutes and zero afterwards, which limit is exceeded?
Check my answer
See the worked solution
The room volume is m³, so at the NAB of 1 mg/m³ the amount is 144 mg. The 8-hour average of that exposure is mg/m³, below the NAB, but 2.5 mg/m³ exceeds the PSD of 2 mg/m³ and its duration is longer than 15 minutes.
The supervisor asks for the lobby floor to be disinfected with chlorine bleach and then crystallized straight away. What is the attendant’s answer?
Check my answer
See the worked solution
The attendant refuses to do the two jobs back to back without rinsing, because chlorine bleach can release chlorine gas when it meets an acidic product. The floor, bucket, and machine tank are rinsed with clean water first, and the order of the work is set by the supervisor.
A café floor of dark stone whose type is not on record looks dull, and an attendant is about to use the same powder. What is done first?
Check my answer
See the worked solution
The type of stone is first confirmed with the building manager or the stone supplier, because the crystallization reaction needs calcium carbonate. If it remains unknown, the product is tested in a hidden spot and the result is assessed by the stone supplier or a stone restoration contractor.
References
External sources
- NIOSH Pocket Guide to Chemical Hazardscdc.gov
- Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
- OpenStax: Chemistry 2eopenstax.org
- Control of exposure to silica dust: A guide for employeeshse.gov.uk
- Preservation Briefs 1: Assessing Cleaning and Water-Repellent Treatments for Historic Masonry Buildingsnps.gov
- Mohs Hardness Scalenps.gov
- Corrosion Resistance Surface Treatment for Marblenps.gov
- Chlorinecdc.gov
- Cleaninghse.gov.uk
Revision history
| Date | Version | Change |
|---|---|---|
| November 15, 2026 | 1 | First published |
How to cite
Kurnia (2026). Marble floor crystallization and polishing: oxalic acid powder, the reaction with calcium carbonate, polishing slurry and the machine, floor care products, dust and splashes, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/kristalisasi-dan-poles-lantai-marmer-serbuk-asam-oksalat-reaksi-dengan-kalsium-karbonat-bubur-poles-dan-mesin-produk-perawatan-lantai-debu-dan-percikan-serta-penanganan-dan-penyimpanan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.
A quantity of 250 g of powder with an anhydrous oxalic acid content of 80 percent reacts completely with marble. How many grams of calcium carbonate are consumed and how many liters of carbon dioxide are released at 25 °C?
Why does part of the calcium from the marble precipitate again in work with oxalic acid? Calculate the molar solubility of calcium oxalate monohydrate from its solubility product.
An attendant rubs an eye with a powder-covered glove and the eye stings. What is done, and why is the work not continued?
Nearby chapters
Reading order by shelf: Chemistry · Chapter 33.
Reading order by shelf: Chemistry · Chapter 31.