By Kurnia · Published November 15, 2026 · Version 1 · 21 min read
Hand soaps and hand sanitizers from the product side
potassium soap and surfactants, benzalkonium chloride, ethanol at 60 to 70 percent and flash point, dispensers and refilling, staff skin, and handling and storage
At a health care facility in the United States, alcohol gel on a worker’s hands was ignited by a static spark moments after a polyester gown was taken off. This chapter covers hand soaps and hand sanitizers from the product side for staff in hotels, kitchens, laundries, and hospitals: potassium soap, sodium lauryl sulfate, and benzalkonium chloride according to the manufacturer’s safety data sheets, ethanol at 60 to 70 percent and the difference between percent by mass and percent by volume, a flash point of 23 °C and what it means in a warm storeroom, the ban on topping off a dispenser that is not yet empty, where alcohol-based dispensers are placed, storage, spills, first aid, and staff skin. Handwashing technique, dosing, sanitizer recipes, and claims about a product’s germ-killing power are not given. Storage quantities, large spills, fires, and skin disorders are stated as work for other parties.
The CDC hand hygiene guideline of 2002 includes a report from a health care facility in the United States. A health care worker applied alcohol gel to their hands, immediately took off a polyester isolation gown, then touched a metal door before the alcohol had evaporated. Taking off the gown built up a substantial static charge, the spark was audible when the door was touched, and the alcohol that had not yet evaporated on the worker’s hands ignited. CDC uses this incident to stress that hands are rubbed together until all the alcohol has evaporated.
Fires like that are rare, but the product is in hotel lobbies, at kitchen doors, and in ward corridors, next to soap dispensers that are refilled every day. The staff who fill, install, and store these products need to know what is in them, how flammable they are, how a dispenser is filled, and what they do to the skin.
Scope
This chapter covers three hand hygiene products from the product side: a gel hand soap containing potassium soap and benzalkonium chloride, a liquid hand soap containing synthetic surfactants, and an ethanol-based hand sanitizer. The product data come from the manufacturer’s safety data sheet for one product of each class. Other products can differ, so what applies in the workplace is the label and the safety data sheet of the product actually in use.
This chapter is learning material, not a work instruction. All three products are sold ready to use, so this chapter gives no dilution rates, gives no recipe for making or mixing hand sanitizer, and does not assess the germ-killing power of any product. Statements about germs are taken only from WHO and CDC.
When and how hands are washed is in Chapter 11 · Biology & Microbiology on the chain of infection transmission and standard precautions, how alcohol and quaternary ammonium work is in Chapter 4 · Biology & Microbiology on disinfectants and how they work, and the skin is in Chapter 41 · Biology & Microbiology on the skin and chemicals. How to check a data sheet is in Chapter 26 on reading the safety data sheets of cleaning products, and surface sanitizers are in Chapter 40 on quaternary ammonium sanitizers for kitchen surfaces.
Work outside the authority of staff and building technicians: making or diluting hand sanitizer, setting storage quantities and the placement of alcohol-based dispensers, handling a large spill or a fire, and treating skin disorders. Making the product is the work of the manufacturer or the hospital pharmacy department, storage quantities and dispenser placement are decided by the building’s fire safety officer, large spills and fires are handled by the emergency response team, and the skin is examined by a doctor or the occupational health service. The product is chosen by the supervisor together with the supplier, and in a hospital together with the infection prevention and control team.
Three products beside the sink: contents and pH
According to the manufacturer’s safety data sheet for one product of each class, all three products are sold ready to use. Their data are as follows.
| Data | Gel soap | Liquid soap | Hand sanitizer |
|---|---|---|---|
| Form | gel | liquid | liquid |
| Ingredients and concentration | potassium salts of coconut fatty acids (CAS 61789-30-8) 5 to 10 percent; benzalkonium chloride (CAS 63449-41-2) 0.1 to 1 percent | sodium lauryl sulfate (CAS 151-21-3) 1 to 10 percent; cocamidopropyl betaine (CAS 61789-40-0) 1 to 5 percent | ethanol (CAS 64-17-5) 60 to 70 percent |
| pH of the undiluted product | 6 to 8 | 6 to 7 | 5.0 to 7.0 |
| Relative density | 1.030 to 1.050 | 1.0187 to 1.02 | 0.850 to 0.900 |
| Flash point | no data | no data | 23 °C, closed cup |
| Classification as written | eye irritation category 2B | eye irritation category 2B | flammable liquid category 3; eye irritation category 2B |
| Storage temperature | 5 to 50 °C | 5 to 50 °C | 0 to 35 °C |
| Validity of the data sheet | February 22, 2024 to February 21, 2029 | February 22, 2025 to February 21, 2030 | 2025 to 2028 |
Concentrations on a data sheet are written as ranges, so those figures state limits, not the exact concentration (Example 1). The hand sanitizer data sheet does not say whether its ethanol percentage is percent by mass or percent by volume, and the class of cocamidopropyl betaine is not stated. What is not written is asked of the supplier, not guessed.
Potassium soap, synthetic surfactants, and benzalkonium chloride
Soap is a sodium or potassium salt of long-chain fatty acids, formed when a fat or oil is reacted with a strong base. That reaction, saponification, is covered in Chapter 35 on degreasers and burnt-on residue removers. Potassium soap is soap whose metal ion is potassium; in the gel soap in the table, the fatty acids come from coconut oil. Sodium lauryl sulfate is a synthetic detergent with a chain of 12 carbon atoms and a sulfate head group. Soap and this detergent are both anionic surfactants, a class covered in Chapter 21 on surfactants, colloids, and emulsions.
Soap cleans hands by lifting dirt off, not by killing germs. CDC writes that the cleaning activity of soap comes from its detergent properties, which remove dirt and organic substances from the hands, and that plain soap has almost no antimicrobial activity. Soap lather forms micelles that trap germs, chemicals, and dirt, and rinsing then carries them down the drain.
Benzalkonium chloride is a quaternary ammonium compound, that is, a cationic surfactant, and within its class it is the one most widely used as an antiseptic. According to CDC, quaternary ammonium compounds mainly inhibit the growth of bacteria and fungi, although at high concentrations they kill certain organisms, are more active against Gram-positive bacteria than against Gram-negative bacilli, are impaired by organic material, and are not compatible with anionic detergents. Because it is weak against Gram-negative bacteria, a benzalkonium chloride solution is itself easily contaminated by those bacteria, and several outbreaks have been traced to contaminated quaternary ammonium solutions.
Potassium soap is an anionic detergent. For that reason the germ-killing power of a soap that combines potassium soap with benzalkonium chloride cannot be concluded from its ingredient list, and the test evidence is asked of the supplier. For people other than health care workers, CDC writes that studies have found no added health benefit from antibacterial soap compared with plain soap.
Ethanol at 60 to 70 percent: concentration and working limits
Alcohol-based hand sanitizer is an alcohol-containing preparation that is rubbed onto the hands without water to reduce the number of viable microorganisms on the hands. According to CDC, alcohol works by denaturing proteins. Solutions at 60 to 95 percent are the most effective, and higher concentrations are in fact less potent because proteins are not easily denatured without water. For the general public CDC asks for an alcohol concentration of at least 60 percent, which is read from the label.
Alcohol concentration can be expressed as percent by mass or percent by volume, and for hand rubs percent by volume is generally used. CDC gives an example: 70 percent by mass is equivalent to 76.8 percent by volume if prepared at 15 °C. The two WHO formulations are likewise written in percent by volume, namely ethanol at 80 percent or isopropyl alcohol at 75 percent. The relationship between the two is
where is the volume fraction of ethanol, is the mass fraction of ethanol, and and are the relative densities of the product and of pure ethanol at the same temperature. This formula takes percent by volume to mean the volume of pure ethanol per volume of product. The density on the data sheet is a range, so the result is an estimate (Example 2).
CDC writes that alcohol has very poor activity against bacterial spores, protozoan oocysts, and certain nonenveloped viruses, and is not appropriate for use when hands are visibly dirty or contaminated with proteinaceous material. Hand sanitizer also does not remove harmful chemicals from the hands, and works well only when hands are not visibly dirty or greasy. The hands of kitchen staff who have just handled food are often greasy, so in a kitchen hand sanitizer does not replace soap and water.
Flash point and ethanol vapor
Flash point is the lowest temperature at which a flammable liquid gives off enough vapor to form an ignitable mixture with air near the surface of the liquid. According to HSE, the British occupational safety authority, a liquid whose flash point is below the ambient temperature always gives off enough vapor for that. Even a liquid below its flash point ignites readily if it is a thin film on a surface or is spilled onto absorbent material such as clothing.
| Liquid | Flash point | According to |
|---|---|---|
| Pure ethanol | 55 °F | NIOSH, United States |
| WHO formulation with ethanol at 80 percent by volume | 17.5 °C | WHO |
| Alcohol-based hand rubs in general | 21 to 24 °C | CDC |
| The hand sanitizer in the product table | 23 °C, closed cup | manufacturer’s data sheet |
The figure of 23 °C fits the classification as written. Category 3 in the European classification rules that HSE uses covers flash points of 23 to 60 °C. Kepmenaker 187/1999 (a Minister of Manpower decree) classes a liquid with a flash point above 21 °C and below 55 °C as a flammable liquid. As of November 2026 the decree is listed as in force on JDIH Kemnaker, the ministry’s legal documentation site.
Storeroom and kitchen temperatures in Indonesia are generally above 23 °C, so this product is stored and used above its flash point. HSE treats a category 3 liquid that can be stored above its flash point like a lower flash point liquid (Example 3).
Ethanol vapor can ignite when its concentration in air lies between the lower flammable limit of 3.3 percent and the upper limit of 19 percent. For health, Permenaker 5/2018 (a Minister of Manpower regulation) lists 1,000 parts per million for ethanol in the short-term exposure and ceiling column, with the note upper respiratory tract irritation. As of November 2026 the regulation is listed as in force on JDIH Kemnaker. The vapor concentration from a given amount of ethanol that evaporates in a closed room is
where is in parts per million (ppm), is the mass of ethanol that evaporates in grams, is the molar mass of ethanol, 46.07 g/mol, is the molar volume of a gas, 24.5 L/mol at 25 °C and 1 atm, and is the room volume in liters. This formula assumes the vapor is evenly mixed, whereas near a spill the concentration is far higher (Example 5). Calculations like this are covered in Chapter 11 on gas stoichiometry.
That vapor ignites only when there is an ignition source. In the opening case the source was a static spark, which is covered in Chapter 18 · Physics on electric fields and potential. WHO asks for hands to be rubbed until dry, because once dry the hands are safe.
Dispensers and refilling
CDC asks that soap not be added to a dispenser that is still partly full, because that practice of topping off can contaminate the soap with bacteria. Refilling or topping off containers of liquid soap has been associated with outbreaks of pathogenic bacteria. A simple calculation shows what happens in a dispenser that is always topped off: the old residue never runs out. If each day a fraction of the contents is used and the dispenser is then topped off until full and its contents are evenly mixed, the fraction of the contents that has been inside since before top-offs is
where and are dimensionless fractions (Example 6). A container and pump that are never empty are also never cleaned.
For hand sanitizer, CDC writes that the safety of refilling or topping off containers has not been well studied. The risks are accidental contamination, reduced effectiveness from alcohol evaporation, and irritation from two formulations being mixed, so refilling is done only according to the manufacturer’s instructions. WHO asks that reusable bottles not be refilled until they have been completely emptied, cleaned, and disinfected. How to clean a soap dispenser is read from its manufacturer’s instructions.
WHO asks that dispensers not be placed above or close to ignition sources such as light switches and electrical outlets, and not next to oxygen or other medical gas outlets. CDC summarizes the requirements of the United States fire safety standard for health care facilities: dispenser contents of at most 1.2 liters in rooms and corridors, horizontal spacing between dispensers of at least 1,220 mm, a distance from ignition sources of at least 25 mm, and the dispenser tested each time a new refill is installed. Those figures apply in their country of origin. Elsewhere, the placement and number of dispensers are decided by the building’s fire safety officer according to local rules.
Storage, spills, and first aid
The hand sanitizer data sheet asks for the product to be kept away from oxidizing substances, and NIOSH notes that ethanol is incompatible with strong oxidizers. Chlorine bleach and peroxide products are oxidizers, as covered in Chapter 25 on chemical reactivity and incompatibility, so alcohol-based liquids are not stored together with either.
CDC asks for supplies of alcohol-based liquids to be stored in cabinets or areas approved for flammable materials. WHO asks for the quantity kept where it is used to be as small as is reasonable for day-to-day needs, for containers to be stored in a cool place away from high temperatures and flames, and for their lids to be secured. Used containers are rinsed with plenty of cold water before being recycled or discarded.
HSE recommends that no more than 50 liters of liquids whose flash point is below the maximum temperature of the workroom be stored in one fire-resisting cabinet. That figure is a recommendation of industry practice, not an absolute limit (Example 4).
For a significant spill, WHO asks for all ignition sources to be removed, the area to be ventilated, and the spill to be diluted with water to at least 10 times its volume. The liquid is then absorbed with an inert material such as dry sand, not a combustible material such as sawdust, and disposed of in a chemical waste container. A soap spill makes the floor slippery and is handled according to Chapter 6 · Safety on chemicals in technician work.
First aid follows the product’s label and data sheet. NIOSH guidance for ethanol:
- Eyes. The eyes are immediately washed with large amounts of water while occasionally lifting the lower and upper lids, then the casualty gets medical attention immediately.
- Skin and clothing. The skin is promptly flushed with water, and irritation that persists is examined by medical personnel. Clothing that is wet with a flammable liquid is removed.
- Swallowed. The casualty is taken to medical attention immediately.
- Inhaled in large amounts. The casualty is moved to fresh air at once.
Soap that gets into the eyes is also rinsed out with plenty of water, and irritation that persists is examined by a doctor, with the product’s label or data sheet brought along.
Staff skin
CDC writes that frequent and repeated use of hand hygiene products, particularly soaps and other detergents, is one of the primary causes of chronic irritant contact dermatitis among health care workers, because detergents damage the proteins of the stratum corneum and change the lipids between its cells. Alcohol can make the skin dry and irritated, but alcohol-based hand rubs that contain moisturizers are better tolerated than washing hands with soap.
Several things make matters worse: hot water, not using hand lotion or cream, and the habit of washing hands with soap immediately after every use of an alcohol-based hand rub. Contact allergies are most often triggered by fragrances and preservatives, and reactions to antiseptics, including quaternary ammonium compounds, have been reported. To look after the skin, CDC recommends water that is not hot, patting the hands dry and not rubbing them, and a hand lotion or cream approved by the facility.
Skin that is dry, red, or cracked is reported early and is not dealt with by switching products on one’s own. The limits of wet work and the sequence avoid, protect, check are in Chapter 41 · Biology & Microbiology on the skin and chemicals.
Worked example
The figures in the examples below are practice figures, unless their origin is stated. The relative densities used are the midpoints of the data sheet ranges, namely 1.040 for the gel soap and 0.875 for the hand sanitizer, and the relative density of pure ethanol is 0.79 according to NIOSH.
Example 1: a concentration range in grams. An 800 mL gel soap refill pouch has a mass of g. Benzalkonium chloride at 0.1 percent means g, and at 1 percent it means g. The potassium soap is g to g. The upper limit for benzalkonium chloride is times its lower limit, so the data sheet alone does not tell the exact concentration in the pouch.
Example 2: percent by mass or percent by volume. If 60 to 70 percent on the data sheet is read as percent by mass, the volume fraction is to , that is, 66.5 to 77.5 percent by volume. The result 77.5 is close to the 76.8 percent by volume that CDC writes for 70 percent by mass. If the same figures are read as percent by volume, 60 percent by volume is equivalent to a mass fraction of , that is, 54.2 percent by mass. On either reading, the lower limit is not less than 60 percent by volume, but the difference between 60 and 66.5 can be settled only from the label or the supplier.
Example 3: flash point and storeroom temperature. The flash point of pure ethanol, 55 °F, equals °C, so the hand sanitizer’s flash point of 23 °C is °C higher. A storeroom without cooling at 31 °C is °C above the product’s flash point, and the storage temperature limit of 35 °C is °C above it. Ignitable vapor is always present above this liquid while its container is open, so what is controlled is the container lid, the ventilation, and the ignition sources.
Example 4: stock in one cabinet. A hotel stores 6 cartons each holding 12 bottles of 500 mL and 2 jerry cans of 5 L. The total is L plus L, that is, 46 L, still below the HSE recommendation of 50 L for one fire-resisting cabinet. One more carton holding L makes it 52 L and passes that figure. The limit that applies in that building remains the decision of the building’s fire safety officer.
Example 5: vapor in a small storeroom. A storeroom measuring 2 m by 1.5 m by 2.4 m has a volume of m³, that is, 7,200 L. A concentration of 1,000 ppm is reached with L of vapor, that is, mol or g of ethanol. At a concentration of 60 percent by mass, that comes from g of product, that is, mL. The lower flammable limit of 3.3 percent corresponds to L of vapor, that is, mol or g of ethanol, from g of product or mL. Less than 1 L evaporating completely in a closed room that small already equals the lower flammable limit on average, and near the spill that limit is reached first.
Example 6: old residue in a dispenser that is always topped off. A 1,000 mL soap dispenser is used 180 times a day at 1.5 mL per press, that is, mL or per day. If it is left until empty, its contents run out in days. If it is topped off until full every day, after 7 days there is still , that is, 11 percent of the contents that is a week old or more, and after 14 days , that is, 1.2 percent. That residue never reaches zero.
Stop conditions
- Hand sanitizer has spilled beyond what the local spill kit can handle, or has spilled near a stove, an oven, an electrical panel, or equipment that is switched on: stop work, stay away from ignition sources, and clear the room. The spill is handed over to trained personnel or the emergency response team.
- An alcohol-based liquid is on fire: sound the alarm and leave the room. The fire is handled by the building emergency response team or the fire department.
- Stock of alcohol-based liquid is near a source of heat or flame, in a room hotter than the storage temperature on the data sheet, together with bleach or other oxidizers, or above the quantity limit for that building: do not add stock. The building’s fire safety officer sets the storage place and quantity.
- An alcohol-based dispenser is mounted above or close to an electrical outlet, a switch, a heating appliance, or an oxygen outlet: do not fill it. A building technician moves it on the decision of the building’s fire safety officer.
- A refill container is unlabeled, the contents of a dispenser are unknown, or there is a request to top off onto the residue of an old product or onto another product: do not fill it. The supervisor decides on replacing the container.
- The soap in a dispenser has changed odor or color, is cloudy, or is slimy: the dispenser is not used. The supervisor contacts the supplier, and in a hospital the infection prevention and control team.
- There is a request to dilute hand sanitizer, add water or alcohol, or make it in-house: do not do it. Making the product is the work of the manufacturer or the hospital pharmacy department.
- The label is missing, or the safety data sheet is absent or past its validity date: the product is not used until the supervisor has an explanation from the supplier.
- Product gets into the eyes and irritation persists, product is swallowed, or clothing is wet with alcohol-based liquid: give first aid, keep away from flames, and take the casualty to a doctor or the emergency services.
- The skin of the hands is red, itchy, or cracked, or a reaction appears after a product is changed: report to the supervisor. The examination is done by a doctor or the occupational health service.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
Antibacterial soap is always better than plain soap.
Why is it wrong?
Soap works by lifting off dirt and germs. According to CDC, studies have found no added health benefit from antibacterial soap for people other than health care workers.
Common misconception
Hand sanitizer replaces handwashing in the kitchen.
Why is it wrong?
Hand sanitizer does not work well on hands that are visibly dirty or greasy, and is weak against spores and certain viruses.
Common misconception
A flash point of 23 °C means the product is dangerous only if it is heated.
Why is it wrong?
Storerooms and kitchens in Indonesia are generally warmer than 23 °C, so ignitable vapor is already present at room temperature.
Common misconception
Topping off soap in a dispenser that is still partly full is thrifty and carries no risk.
Why is it wrong?
The old residue never runs out, and CDC associates that practice with soap contaminated with bacteria.
Common misconception
A product made for hands is always safe for the skin.
Why is it wrong?
Frequent use of soap is one of the primary causes of irritant contact dermatitis among health care workers, and fragrances and preservatives can trigger allergies.
Links to other chapters
Chapter 11 · Biology & Microbiology on the chain of infection transmission and standard precautions covers when and how hands are washed. Chapter 41 · Biology & Microbiology on the skin and chemicals explains dermatitis and wet work, and Chapter 17 · Buildings & Facilities on inspection-level fire protection covers the fire triangle and fire extinguishers.
Exercises and worked solutions
The figures in the questions are for practice.
Try to answer first, then open the worked solution.
A 500 mL bottle of hand sanitizer has a relative density of 0.875. How many grams of ethanol does it hold if the concentration is 60 percent by mass and if it is 70 percent by mass?
Check my answer
See the worked solution
The mass of the bottle’s contents is g, so the ethanol is g to g. More than a quarter of a kilogram of ethanol is in one small bottle, so the bottles on a trolley are counted as stock too.
An air-conditioned storeroom is kept at 20 °C, below the flash point of 23 °C. May the hand sanitizer in that storeroom be treated like a liquid that is not flammable?
Check my answer
See the worked solution
No. The margin is only °C and is gone as soon as the cooling fails, and even a liquid below its flash point ignites readily if it is a thin film or is spilled onto clothing. Container lids, ventilation, distance from ignition sources, and quantity limits still apply.
A staff member adds soap from a jerry can to every dispenser each morning without waiting for them to be empty. What is wrong and what is the correction?
Check my answer
See the worked solution
Topping off a dispenser that is not yet empty means the old residue never runs out, and CDC associates it with soap contaminated with bacteria. The dispenser is used until empty, then its container is replaced or cleaned according to the manufacturer’s instructions before it is filled again.
A room measuring 3 m by 2 m by 2.5 m is tightly closed. How many milliliters of hand sanitizer at 60 percent by mass and a relative density of 0.875 evaporate to equal 1,000 ppm of ethanol?
Check my answer
See the worked solution
The room volume is m³ or 15,000 L, so 1,000 ppm corresponds to L of vapor, that is, mol or g of ethanol. That comes from g of product, that is, mL, so even a spill that small is handled with the ventilation open.
A cook finishes cutting raw chicken with greasy hands, then uses only hand sanitizer before plating a dish. What is wrong?
Check my answer
See the worked solution
Hand sanitizer does not work well on hands that are visibly dirty or greasy and does not lift dirt off. The hands are washed with soap and water according to Chapter 11 · Biology & Microbiology on the chain of infection transmission and standard precautions.
Two weeks after the soap was changed, three dishwashing staff complain of dry, red, and itchy hands. What does the supervisor do?
Check my answer
See the worked solution
The complaints are recorded and the staff are examined by a doctor or the occupational health service, because examining and treating the skin is the work of medical personnel. The supervisor asks the supplier what the new soap contains and checks the water temperature, the hand cream, and the duration of wet work according to Chapter 41 · Biology & Microbiology on the skin and chemicals.
References
External sources
- Guideline for Hand Hygiene in Health-Care Settings: Recommendations of the Healthcare Infection Control Practices Advisory Committee and the HICPAC/SHEA/APIC/IDSA Hand Hygiene Task Forcecdc.gov
- Hand Hygiene Frequently Asked Questionscdc.gov
- Clinical Safety: Hand Hygiene for Healthcare Workerscdc.gov
- Guide to Local Production: WHO-recommended Handrub Formulationswho.int
- Storage of flammable liquids in containershse.gov.uk
- NIOSH Pocket Guide to Chemical Hazards - Ethyl alcoholcdc.gov
- First Aid Procedures for Chemical Hazardscdc.gov
- Keputusan Menteri Tenaga Kerja Nomor Kep.187/MEN/1999 tentang Pengendalian Bahan Kimia Berbahaya di Tempat Kerjajdih.kemnaker.go.id
- Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
Revision history
| Date | Version | Change |
|---|---|---|
| November 15, 2026 | 1 | First published |
How to cite
Kurnia (2026). Hand soaps and hand sanitizers from the product side: potassium soap and surfactants, benzalkonium chloride, ethanol at 60 to 70 percent and flash point, dispensers and refilling, staff skin, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/sabun-cuci-tangan-dan-cairan-sanitasi-tangan-dari-sisi-produk-sabun-kalium-dan-surfaktan-benzalkonium-klorida-etanol-60-sampai-70-persen-dan-titik-nyala-dispenser-dan-isi-ulang-kulit-petugas-serta-penanganan-dan-penyimpanan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
A 500 mL bottle of hand sanitizer has a relative density of 0.875. How many grams of ethanol does it hold if the concentration is 60 percent by mass and if it is 70 percent by mass?
An air-conditioned storeroom is kept at 20 °C, below the flash point of 23 °C. May the hand sanitizer in that storeroom be treated like a liquid that is not flammable?
A staff member adds soap from a jerry can to every dispenser each morning without waiting for them to be empty. What is wrong and what is the correction?
Nearby chapters
Reading order by shelf: Chemistry · Chapter 44.
Reading order by shelf: Chemistry · Chapter 42.