Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Chemistry · Chapter 35Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Degreasers and burnt-on residue removers

    sodium hydroxide and pH 14, saponification of fats, dilution of 1 to 1 through 5, aluminum and painted surfaces, personal protective equipment, and handling and storage

    A 4 percent sodium hydroxide solution starts to burn only several hours after it touches the skin, although in volunteers the epidermis was already completely destroyed within 60 minutes. Degreasers for burnt-on residue in hotel kitchens sit around that concentration. This chapter covers that class of product from the side of the people who use it: sodium hydroxide at 1 to 5 percent and pH 14 according to the manufacturer’s safety data sheet for one product of this class, saponification of fats as the way it works, dilution of 1 to 1 through 5 and the pH of the use solution, aluminum, zinc, tin, and painted surfaces that are damaged by a strong base, the hazards to skin, eyes, and breathing together with the figure of 2 mg/m³ in Permenaker 5/2018, personal protective equipment, first aid, and handling and storage. Contact times and surface temperatures are not given and are read from the product label. Cleaning hood exhaust ducts, the hood suppression system, repair of damaged surfaces, large spills, and treatment of casualties are stated as the work of other parties.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    Shortly before a hotel kitchen closes, a kitchen steward cleans the grill and the hood grease filters with a degreaser that has already been diluted. As a filter is lifted out of the soak tank, liquid runs into a glove and wets a shirt sleeve. Nothing stings, so the work goes on. Several hours later the skin under that sleeve is red, sore, and starting to blister. This sequence matches the review of sodium hydroxide exposure limits carried by NIOSH, the United States occupational safety and health institute: sodium hydroxide solutions of 25 to 50 percent cause a sensation of irritation within about three minutes, whereas with a 4 percent solution the sensation of burning does not appear until several hours later. In volunteers who had a solution equal to 4 percent applied to their arms, the epidermis was completely destroyed within 60 minutes.

    Degreasers for burnt-on residue in commercial kitchens sit around that concentration. According to the manufacturer’s safety data sheet for one product of this class, the listed ingredient is sodium hydroxide at 1 to 5 percent, with pH 14. That seemingly small concentration misleads in two ways: the liquid is not felt on the skin right away, and pH 14 is the top end of the pH scale of 0 to 14. The base that lifts grease off the grill also dissolves aluminum and lifts paint.

    Scope

    This chapter covers one class of product, namely liquid degreasers based on sodium hydroxide for burnt-on residue on ovens, grills, and hood grease filters: contents and pH, saponification of fats, dilution, metals and coatings damaged by a strong base, hazards to the body, personal protective equipment, first aid, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of this class. Other products can differ, so what applies in the workplace is the label and the safety data sheet of the product actually in use.

    This chapter is learning material, not a work instruction. The only rate written here is the dilution range on that data sheet. The rate for each job, the contact time, and the surface temperature are read from the product label, the equipment manual, and the workplace procedure. Mixing recipes are not given, and the cleaning power of the product is not assessed.

    How to check the contents of a data sheet is in Chapter 26 on reading the safety data sheets of cleaning products. Labels and spills are in Chapter 6 · Safety on chemicals in technician work, incompatible pairs of materials in Chapter 25 on chemical reactivity and incompatibility, and burns from bases in Chapter 41 · Biology & Microbiology on the skin and chemicals. Floor cleaners are covered in Chapter 36 on strong alkaline kitchen floor cleaners, and sodium hydroxide at higher concentrations in Chapter 37 on liquid machine dishwashing detergent. Automatic washing is in Chapter 3 · Commercial Kitchens on combi ovens, boil-out cleaning in Chapter 2 · Commercial Kitchens on commercial gas fryers, the suppression system in Chapter 4 · Commercial Kitchens on wet chemical kitchen hood suppression systems, and waste grease in Chapter 34 · Water & Water Treatment on used cooking oil, grease, and used oil.

    Work outside the authority of kitchen stewards and kitchen technicians: cleaning the inside of hood exhaust ducts, removing or spraying parts of the hood suppression system, repairing aluminum that has been eaten away or paint that has lifted, handling a large spill, and giving treatment other than first aid. Exhaust ducts are handled by the kitchen duct cleaning contractor, the suppression system by the suppression system technician, equipment repair by the technician appointed by the equipment supplier or the building manager, large spills by trained personnel or the emergency response team, and casualties by a doctor or the emergency services. The choice of product is decided by the kitchen supervisor together with the supplier.

    What the product contains: sodium hydroxide and pH 14

    According to the manufacturer’s safety data sheet for one product of this class, the degreaser is a liquid that is soluble in water, made for professional use as a burnt-on residue remover. Only one ingredient is listed, namely sodium hydroxide with CAS number 1310-73-2 at 1 to 5 percent. The pH of the undiluted product is 14 and its relative density is 1.1856. The data sheet classifies the product as corrosive to the skin, Category 1A, and hazardous to the eyes, Category 1, was issued on February 22, 2025, and is valid until February 21, 2030.

    Sodium hydroxide, with the formula NaOH, is an inorganic base in the form of a colorless to white, odorless solid, also known as caustic soda or lye. A strong base is a base that ionizes completely in water, so each mole of sodium hydroxide that dissolves gives one mole of hydroxide ions. Those hydroxide ions are what act on fat, metal, and skin. For a strong base at a concentration of CC mol/L at 25 °C,

    [OH−]=C,pOH=−log⁡[OH−],pH=14.00−pOH[\text{OH}^-] = C, \qquad \text{pOH} = -\log [\text{OH}^-], \qquad \text{pH} = 14.00 - \text{pOH}

    where [OH−][\text{OH}^-] is the hydroxide ion concentration in mol/L. This formula assumes an ideal solution, so for a solution as concentrated as this product the result is an estimate, not a substitute for measurement. Each rise of one pH unit means the hydroxide ion concentration rises 10 times. pH 14 means about 1 mole of hydroxide ions per liter, which agrees with the concentration of 1 to 5 percent on the data sheet (Example 2).

    NIOSH writes that sodium hydroxide solutions with a pH of 11.5 or greater should be considered corrosive to the skin. pH 11.5 corresponds to a concentration of about 0.003 mol/L, and more dilute solutions can still irritate. A product at pH 14 is about 333 times more concentrated than that line. Other ingredients in the product are not known from that data sheet.

    Saponification: why a strong base lifts fat

    Fats and oils are esters of glycerol, an alcohol with three hydroxyl groups, with long-chain carboxylic acids such as palmitic acid, stearic acid, and oleic acid. When a fat is treated with a base such as sodium hydroxide, glycerol and salts of fatty acids are formed, and those salts of fatty acids are soap. Saponification is the hydrolysis of fat by alkali into glycerol and soap. Because one fat molecule contains three ester bonds, each mole of fat requires three moles of sodium hydroxide:

    fat+3 NaOH→glycerol+3 soap\text{fat} + 3\,\text{NaOH} \rightarrow \text{glycerol} + 3\,\text{soap}

    Fat does not dissolve in water, whereas glycerol and sodium soap do, so part of the soil turns into material that rinses away. The soap that forms also helps lift fat that has not yet reacted: the hydrocarbon end of its molecule is attracted to oil and its ionic end is attracted to water, so the soap becomes a bridge between the soil and the water. How surfactants work is described in Chapter 21 on surfactants, colloids, and emulsions.

    Burnt-on residue is fat and food residue that has been baked on again and again until it is hard. The part that has already turned to char is no longer fat and cannot be saponified. That part comes off because the fat under it and in its gaps dissolves, and it is then lifted with a scraper that suits the surface material.

    Three limits need to be kept in mind. Sodium hydroxide is used up as it reacts, so a given amount of solution saponifies only a given amount of fat (Example 4). The reaction takes time, and the contact time is read from the label. HSE, the British occupational safety authority, notes that some cleaning substances cause breathing problems if they are oversprayed, used without adequate ventilation, or sprayed onto hot surfaces, for example improperly used oven cleaner. The surface temperature at which the product is used therefore follows the label.

    Dilution of 1 to 1 through 5

    The safety data sheet for a product of this class gives a dilution of 1 : 1 to 1 : 5, and this chapter gives no other rate. Which dilution is used for which job is read from the product label. As in Chapter 27 on neutral all-purpose cleaners, the ratio 1 : n is read as one part product plus n parts water. With that reading, for a use solution of volume VV,

    Vp=V1+n,Cuse=C1+n,pHuse=pH−log⁡(1+n)V_p = \frac{V}{1 + n}, \qquad C_{use} = \frac{C}{1 + n}, \qquad \text{pH}_{use} = \text{pH} - \log(1 + n)

    where VpV_p is the volume of product in the same unit as VV, CC is the sodium hydroxide concentration of the product, and CuseC_{use} is its concentration in the use solution. The pH formula holds for a strong base at 25 °C and assumes that the volumes of product and water can be added.

    A product at pH 14 that is diluted 1 : 5 is still at about pH 13.2, and its hydroxide ion concentration is still tens of times the concentration that NIOSH considers corrosive to the skin (Example 3). The use solution of this class is treated the same as the concentrated product, with the same protective equipment.

    HSE asks that the concentrated liquid always be added to water, not the water to the concentrate, and that spray bottles and other containers be clearly marked with their contents. A spray bottle turns the solution into a mist that is easily inhaled and easily reaches the eyes, so the method of use recommended on the label is followed.

    Aluminum, other metals, and painted surfaces

    The safety data sheet for a product of this class names acids and metals as incompatible materials. NIOSH specifies those metals as aluminum, tin, and zinc, and adds that sodium hydroxide is corrosive to metals.

    Amphoteric is the property of a substance that reacts with both acids and bases. Aluminum is amphoteric. With sodium hydroxide, one possible reaction is

    2 Al(s)+2 NaOH(aq)+6 H2O(l)→2 Na[Al(OH)4](aq)+3 H2(g)2\,\text{Al}(s) + 2\,\text{NaOH}(aq) + 6\,\text{H}_2\text{O}(l) \rightarrow 2\,\text{Na}[\text{Al(OH)}_4](aq) + 3\,\text{H}_2(g)

    Aluminum is normally protected by a thin, hard film of oxide, but aluminum oxide also reacts with bases, so that film does not survive in a sodium hydroxide solution. The reaction of aluminum with either acids or bases generates hydrogen gas, and a mixture of hydrogen and oxygen explodes if ignited. In a kitchen, pots, baking pans, and hood grease filters can be made of aluminum. Such items fizz and are eaten away when soaked in a degreaser, and the bubbles are hydrogen (Example 5).

    SurfaceEffect of a strong baseGuidance
    Aluminum: pots, baking pans, grease filtersdissolves and releases hydrogen gasdegreasers of this class are not used; the material of the item is confirmed before soaking
    Zinc and tin, including zinc-coated steelclassed as incompatible with sodium hydroxideavoid contact and rinse off splashes
    Painted and coated surfacesalkaline paint removers are used to remove oil, latex, and acrylic paintspainted panels and walls are covered or kept away from splashes

    The last row comes from the building preservation guidance of the United States National Park Service, which also notes that sodium hydroxide can stain stone and asks that the manufacturer’s recommendations always be tested before work begins. For the inside of cooking equipment, the cleaner that may be used is set by the equipment manual, as covered in Chapter 3 · Commercial Kitchens on combi ovens. Damage from a strong base cannot be rinsed away, and its repair is the work of another party.

    Hazards to skin, eyes, and breathing

    NIOSH lists the exposure routes of sodium hydroxide as inhalation, ingestion, and skin and eye contact, with symptoms of irritation of the eyes, skin, and mucous membranes, pneumonitis, burns to the eyes and skin, and temporary loss of hair.

    On the skin, the danger is the gap between contact and pain. A 4 percent solution starts to burn only several hours later, and if it is not removed from the skin sodium hydroxide causes severe burns with deep ulceration. In one study, a 2 percent solution applied under occlusion for 1 hour caused severe crusting in some volunteers and no inflammation in others. A shirt sleeve or a glove that is wet on the inside works like that occluded patch.

    In the eyes, damage happens far faster. The review carried by NIOSH names sodium hydroxide as the cause of some of the most severe, blinding chemical burns of the eye, with the worst feature being the speed of the damage to the front of the eye. Eye protection is therefore put on before the container is opened.

    Permitted ceiling concentration (Indonesian kadar tertinggi diperkenankan, KTD) is the concentration of a chemical in workplace air that must not be exceeded even for an instant while workers are doing their work. Permenaker (Minister of Manpower Regulation) 5/2018 lists sodium hydroxide with a figure of 2 mg/m³ in the column for short-term exposure and ceiling concentration, with no 8-hour average figure, and with the note irritation of the upper respiratory tract, skin, and eyes. As of November 2026 the regulation is listed as in force on JDIH Kemnaker, the ministry’s legal documentation site. The limit recommended by NIOSH is also 2 mg/m³ as a ceiling.

    That figure concerns sodium hydroxide suspended in the air as a mist, for example from a spray bottle. Brief exposure at 2 mg/m³ already causes mild irritation of the nose. A few milliliters of use solution that turn into mist in a kitchen without ventilation already equal that figure (Example 6).

    Personal protective equipment and first aid

    For sodium hydroxide, NIOSH asks that skin and eye contact be prevented, that wet or contaminated clothing be removed, and that an eyewash and a quick-drench facility be available. The choice of personal protective equipment is covered in Chapter 5 · Safety on personal protective equipment. HSE guidance for cleaning substances in hospitality:

    • The protective clothing provided is always worn when handling cleaning substances, especially concentrates.
    • Eye protection suitable for splashes, for example goggles or a visor, is worn if there is any danger of splashing and when cleaning at eye level or above, such as a hood.
    • Rubber gloves are checked for holes and tears, and replaced if faulty.
    • Cleaning substances are used only in well-ventilated areas, and mechanical ventilation must be switched on and working.
    • Where tap water is not available for eye irrigation, at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers is provided.

    The glove material, the apron, and the need for respiratory protection are read from the product data sheet.

    First aid follows the product data sheet and the workplace procedure. Guidance from NIOSH for sodium hydroxide and from HSE for chemical injuries:

    1. Eyes. The eyes are immediately washed with large amounts of water while occasionally lifting the upper and lower lids, then the casualty is taken to medical attention immediately. HSE asks for the eye to be flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then for the casualty to be sent to hospital.
    2. Skin. The skin is immediately flushed with water without waiting for it to sting. If the liquid penetrates the clothing, the clothing is immediately removed and the skin flushed, then the casualty gets medical attention. For chemical burns, HSE asks for the affected area to be flooded with water for 20 minutes, for contaminated clothing that is not stuck to the skin to be removed, and for the first aider to avoid being contaminated as well.
    3. Swallowed. The casualty is taken to medical attention immediately.
    4. Inhaled. The casualty is moved to fresh air at once, kept warm and at rest, and gets medical attention as soon as possible. If breathing has stopped, a trained rescuer gives artificial respiration and the emergency services are called.

    The label or the product data sheet is taken to the doctor, and what happens next is the decision of the medical staff.

    Handling and storage

    The manufacturer’s safety data sheet for one product of this class gives a storage temperature of 0 to 50 °C and asks that the product be kept away from acidic compounds. NIOSH adds flammable liquids to the list of materials incompatible with sodium hydroxide. A degreaser is therefore not stored together with acidic descalers, which are covered in Chapter 39 on descalers for dishwashers and kitchen equipment, and is not held in an aluminum container.

    HSE gives guidance on storing and handling cleaning substances in hospitality:

    • Substances are kept in their original labeled containers. A decanting container is made of a suitable material, clean, and clearly marked with the instructions for use and the hazards.
    • Cleaning substances are never transferred into food or drink containers.
    • The storage place is away from heat, sunlight, foodstuffs, and members of the public, and all containers have lids.
    • Pouring from heavy bulk containers is avoided; a pump or a siphon is used.
    • Cleaning substances are never mixed.

    The ban on mixing also applies to using products one after the other. An acid that meets leftover base neutralizes it and releases heat, as covered in Chapter 25 on chemical reactivity and incompatibility, so the surface is rinsed thoroughly with water before another product is used. Small spills are handled according to Chapter 6 · Safety on chemicals in technician work, and leftover product and empty containers according to the label and Chapter 35 · Water & Water Treatment on B3 waste.

    Worked example

    The figures in the examples below are practice figures, unless their origin is stated. The relative density of 1.1856 and the concentration of 1 to 5 percent come from the data sheet, the molar mass of sodium hydroxide of 40.01 g/mol from Permenaker 5/2018, and the molar gas volume of 24.5 L/mol applies at 25 °C and 1 atm.

    Example 1: mass and moles of sodium hydroxide per liter. One liter of product has a mass of 1.1856×1,000=1,185.61.1856 \times 1{,}000 = 1{,}185.6 g. At 1 percent, the sodium hydroxide is 0.01×1,185.6=11.860.01 \times 1{,}185.6 = 11.86 g, and at 5 percent it is 0.05×1,185.6=59.280.05 \times 1{,}185.6 = 59.28 g. With a molar mass of 40.01 g/mol, the concentration is 11.86/40.01=0.29611.86/40.01 = 0.296 mol/L to 59.28/40.01=1.4859.28/40.01 = 1.48 mol/L. A 5 L jerry can holds 5×59.28=296.45 \times 59.28 = 296.4 g of sodium hydroxide at 5 percent.

    Example 2: does pH 14 agree with 1 to 5 percent. At 0.296 mol/L, pOH =−log⁡0.296=0.53= -\log 0.296 = 0.53, so pH =14.00−0.53=13.47= 14.00 - 0.53 = 13.47. At 1.48 mol/L, pOH =−log⁡1.48=−0.17= -\log 1.48 = -0.17 and pH =14.00+0.17=14.17= 14.00 + 0.17 = 14.17. Exactly pH 14 means 1 mol/L, that is 40.01 g per liter or 40.01/1,185.6=3.3740.01/1{,}185.6 = 3.37 percent of the mass of the product. The figure of pH 14 lies inside the calculated range of 13.47 to 14.17, so the concentration and the pH on that data sheet agree with each other.

    Example 3: use solutions at 1 : 1 and 1 : 5. For 2 liters of use solution, a 1 : 1 dilution needs 2,000/(1+1)=1,0002{,}000/(1 + 1) = 1{,}000 mL of product and a 1 : 5 dilution needs 2,000/(1+5)=3332{,}000/(1 + 5) = 333 mL. From a product at pH 14, that is 1 mol/L, the 1 : 1 solution has a concentration of 1/2=0.51/2 = 0.5 mol/L with a pH of 14−log⁡2=13.7014 - \log 2 = 13.70, and the 1 : 5 solution has a concentration of 1/6=0.1671/6 = 0.167 mol/L with a pH of 14−log⁡6=13.2214 - \log 6 = 13.22. Compared with the concentration of 0.003 mol/L that NIOSH already considers corrosive to the skin, that weakest solution is still 0.167/0.003=560.167/0.003 = 56 times more concentrated.

    Example 4: upper limit of the fat that can be saponified. Half a liter of 1 : 1 use solution from a product at 5 percent contains 0.5×1.48/2=0.3700.5 \times 1.48/2 = 0.370 mol of sodium hydroxide. Each mole of fat requires 3 moles of sodium hydroxide, so the fat that can react is at most 0.370/3=0.1230.370/3 = 0.123 mol. If the fat is represented by glyceryl tristearate, C57H110O6\text{C}_{57}\text{H}_{110}\text{O}_6, with a molar mass of 891.5 g/mol, that amount is 0.123×891.5=1100.123 \times 891.5 = 110 g. This is a stoichiometric upper limit, not a measure of cleaning power. Thicker residue is dealt with by repeating according to the label, not by mixing in another product.

    Example 5: aluminum that dissolves and its hydrogen gas. An aluminum grease filter that loses 10 g of metal in the soak tank has dissolved 10/26.98=0.37110/26.98 = 0.371 mol of aluminum. Every 2 moles of aluminum release 3 moles of hydrogen, so the hydrogen is 0.371×3/2=0.5560.371 \times 3/2 = 0.556 mol, that is 0.556×24.5=13.60.556 \times 24.5 = 13.6 L. More than 13 liters of ignitable gas form in the soak tank.

    Example 6: mist and the figure of 2 mg/m³. A kitchen measuring 5 m by 4 m by 3 m has a volume of 5×4×3=605 \times 4 \times 3 = 60 m³. A concentration of 2 mg/m³ is reached with 2×60=1202 \times 60 = 120 mg of sodium hydroxide in the air. A 1 : 1 use solution from a product at 5 percent contains 59.28/2=29.6459.28/2 = 29.64 g of sodium hydroxide per liter, so 120 mg equals 120/29.64=4.0120/29.64 = 4.0 mL of solution. Four milliliters of solution that turn into mist in a kitchen without ventilation already equal that figure, so the exhaust fan is switched on before the product is used.

    Stop conditions

    1. Liquid gets into the eyes: rinse at once with large amounts of water while holding the lids open, and take the casualty to the emergency services. The supervisor gets the product data sheet ready for the medical staff.
    2. Liquid gets on the skin, wets clothing, or runs into a glove, even though nothing stings: stop work, remove the wet clothing or glove, and flush the skin with water. Examination and treatment are done by a doctor.
    3. The item is made of aluminum or an unknown metal, or metal fizzes when the solution touches it: do not soak or spray it again, rinse it with water, and keep it away from flames. The technician appointed by the equipment supplier or the building manager assesses the material and the damage.
    4. Paint or a protective coating softens or lifts: stop and rinse. Repair is handed to the contractor appointed by the building manager.
    5. The surface is still hot or a pilot flame is lit: do not spray. The kitchen supervisor decides when the equipment is ready to be cleaned, and shutting off gas or electricity is done by the kitchen technician.
    6. An acidic descaler or another product has already been used on the same surface, or the tank, bucket, and bottle are unlabeled: do not use the degreaser. The kitchen supervisor decides the order of work and the containers to be used.
    7. Coughing or a stinging throat while spraying, or the hood exhaust fan is off: stop and move to fresh air. The building technician restores the ventilation, and anyone short of breath is taken to the emergency services.
    8. A spill is larger than the local spill kit can handle: keep people away and hand over to trained personnel or the emergency response team.
    9. The work touches parts of the hood suppression system or requires entry into the exhaust duct: stop. The suppression system is handled by the suppression system technician, and the exhaust duct by the kitchen duct cleaning contractor.
    10. The label is missing, the safety data sheet is absent or past its validity date, or its contents do not match the label: the product is not used until the supervisor obtains an explanation from the supplier.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    It is only 1 to 5 percent, so this is a mild cleaner.

    Why is it wrong?

    The pH of the product is 14, and a solution equal to 4 percent destroyed the whole epidermis of volunteers within 60 minutes. NIOSH considers sodium hydroxide solutions corrosive to the skin from about 0.003 mol/L.

    Common misconception

    It does not sting, so it is fine.

    Why is it wrong?

    With a 4 percent solution, the sensation of burning appears only several hours later. The skin is flushed right then, and wet clothing is removed.

    Common misconception

    It has been diluted 1 : 5, so no protection is needed.

    Why is it wrong?

    A 1 : 5 solution from a product at pH 14 is still at about pH 13.2. Its protective equipment is the same as for the concentrated product.

    Common misconception

    All metal filters and baking pans can be soaked.

    Why is it wrong?

    Aluminum dissolves in sodium hydroxide and releases hydrogen gas, and tin and zinc are also incompatible.

    Common misconception

    If residue is still there, just follow up with an acid cleaner.

    Why is it wrong?

    An acid and a base that meet neutralize each other and release heat. Cleaning substances are not mixed, and the surface is rinsed thoroughly before another product is considered.

    Chapter 26 on reading the safety data sheets of cleaning products gives the way to check the data sheet that this chapter is based on. Chapter 28 on mildly alkaline all-purpose cleaners covers weaker bases, and Chapter 37 on liquid machine dishwashing detergent covers sodium hydroxide at higher concentrations.

    Exercises and worked solutions

    The figures in the questions are for practice.

    Try to answer first, then open the worked solution.

    1. A 1 liter spray bottle is filled with 1 : 3 use solution from a product with 5 percent sodium hydroxide and a relative density of 1.1856. How many milliliters of product and how many grams of sodium hydroxide are in that bottle?

      Check my answer
      See the worked solution

      The product is 1,000/(1+3)=2501{,}000/(1 + 3) = 250 mL, with a mass of 250×1.1856=296.4250 \times 1.1856 = 296.4 g, so the sodium hydroxide is 0.05×296.4=14.820.05 \times 296.4 = 14.82 g. That bottle holds well over ten grams of strong base, so it is labeled like the original container.

    2. A product at pH 14 is diluted 1 : 5. What is the estimated pH of the use solution, and is that solution already below pH 11.5?

      Check my answer
      See the worked solution

      The pH drops by log⁡6=0.78\log 6 = 0.78, to 14−0.78=13.2214 - 0.78 = 13.22. That figure is still far above 11.5, so the use solution is still treated as a corrosive material with the same protective equipment.

    3. A worker intends to soak the hood grease filters overnight in a degreaser. The filter material is not known. What should be considered?

      Check my answer
      See the worked solution

      The filters are not soaked before their material is confirmed from the hood manual or by a technician, because grease filters can be made of aluminum. Aluminum dissolves in sodium hydroxide and releases ignitable hydrogen gas.

    4. Use solution wets a worker’s shirt sleeve, and their skin feels nothing. What is done?

      Check my answer
      See the worked solution

      Work is stopped, the sleeve is removed, and the skin is flushed with water right then. The absence of stinging is not a sign of safety, because with a solution of about 4 percent the sensation of burning appears only several hours later.

    5. An aluminum baking pan loses 5 g of metal because it was soaked in a degreaser. How many liters of hydrogen gas form at 25 °C and 1 atm?

      Check my answer
      See the worked solution

      The aluminum that dissolves is 5/26.98=0.1855/26.98 = 0.185 mol, so the hydrogen is 0.185×3/2=0.2780.185 \times 3/2 = 0.278 mol, that is 0.278×24.5=6.80.278 \times 24.5 = 6.8 L. That gas is ignitable, so metal that fizzes is kept away from flames.

    6. After a degreaser is used in an oven cavity, limescale is still there, and a worker intends to spray an acidic descaler straight away. What is wrong?

      Check my answer
      See the worked solution

      Cleaning substances are not mixed, and an acid that meets leftover sodium hydroxide neutralizes it and releases heat. The oven cavity is first rinsed thoroughly with water, then the kitchen supervisor decides on the use of a descaler according to the equipment manual.

    References

    External sources

    • 1988 OSHA PEL Project - Sodium Hydroxidecdc.gov
    • NIOSH Pocket Guide to Chemical Hazards - Sodium hydroxidecdc.gov
    • NIOSH Skin Notation Profiles: Sodium Hydroxide (NaOH)cdc.gov
    • First Aid Procedures for Chemical Hazardscdc.gov
    • Safe use of cleaning substances in the hospitality industryhse.gov.uk
    • Basic advice on first aid at workhse.gov.uk
    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
    • Chemistry 2eopenstax.org
    • Preservation Brief 1: Assessing Cleaning and Water-Repellent Treatments for Historic Masonry Buildingsnps.gov

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Degreasers and burnt-on residue removers: sodium hydroxide and pH 14, saponification of fats, dilution of 1 to 1 through 5, aluminum and painted surfaces, personal protective equipment, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/pelarut-lemak-dan-penghilang-kerak-gosong-natrium-hidroksida-dan-ph-14-penyabunan-lemak-pengenceran-1-banding-1-sampai-5-aluminium-dan-permukaan-bercat-alat-pelindung-diri-serta-penanganan-dan-penyimpanan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A 1 liter spray bottle is filled with 1 : 3 use solution from a product with 5 percent sodium hydroxide and a relative density of 1.1856. How many milliliters of product and how many grams of sodium hydroxide are in that bottle?

    2

    A product at pH 14 is diluted 1 : 5. What is the estimated pH of the use solution, and is that solution already below pH 11.5?

    3

    A worker intends to soak the hood grease filters overnight in a degreaser. The filter material is not known. What should be considered?

    Self-assessment progress0%

    Nearby chapters