Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Chemistry · Chapter 36Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Strong alkaline kitchen floor cleaners

    amine oxide, alkyl polyglycoside, and monoethanolamine, pH 13 to 14, dilution, slippery floors and rinsing, and handling and storage

    At a fast food outlet in Britain, a cook slipped on a floor that had just been mopped and was still damp, pulled over a fryer holding 35 liters of hot oil, and the company was fined 60,000 pounds sterling. This chapter covers strong alkaline kitchen floor cleaners from the side of the people who use them: amine oxide, alkyl polyglycoside, and monoethanolamine at 1 to 5 percent each with pH 13 to 14 according to the manufacturer’s safety data sheet for one product of this class, what that pH means against the line of 11.5, how surfactants lift grease, dilution of 1 : 5 to 1 : 100 and the estimated pH of the use solution, contact time, rinsing, and drying so that the floor is not slippery, the threshold limit value for ethanolamine in Permenaker 5/2018, eye and skin protection, first aid, and handling and storage. The rate for each job is read from the product label. Repair or replacement of floors, large spills, and treatment of casualties are stated as the work of other parties.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    After a busy Friday night at a fast food outlet in Britain, the staff were cleaning the kitchen. A cook walked from the pot wash area across a floor that had just been wet mopped by a colleague. Near the fryer the cook slipped on the still damp floor, reached for the electric deep fat fryer to break the fall, and the fryer toppled over. In all, 35 liters of hot oil spilled onto the cook and onto the floor. The cook could not get up because they kept slipping in the oil, until an assistant manager pulled them out and was burned on the hands as well. The cook and another employee suffered severe burns and needed skin grafts. The company was fined 60,000 pounds sterling, and the judge found that poor floor maintenance, poor cleaning, poor footwear, and poor slip resistance of the tiles together increased the likelihood of slipping.

    Kitchen floor cleaners are made to lift the grease that makes a floor slippery, but the way they are used can create the same hazard: a wet floor, detergent residue, and a high-pH solution. According to the manufacturer’s safety data sheet for one product of this class, the pH of the concentrate is 13 to 14. Workers need to understand what is in that jerry can, what its pH figure means, the rate, and why contact time, rinsing, and drying decide whether the floor becomes safer or more dangerous.

    Scope

    This chapter covers one class of product, namely liquid kitchen floor cleaners at pH 13 to 14 that contain amine oxide, alkyl polyglycoside, and monoethanolamine: contents and pH, how surfactants lift grease, dilution, slippery floors and rinsing, hazards to eyes, skin, and breathing, first aid, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of this class. Other products can differ, so what applies in the workplace is the label and the safety data sheet of the product actually in use.

    This chapter is learning material, not a work instruction. The only rate written here is the dilution range on that data sheet. The rate for each job and the contact time are read from the product label, the floor manufacturer’s instructions, and the workplace procedure. Mixing recipes are not given, and neither cleaning power nor germ-killing power is assessed.

    Types of floor covering and slip testing are in Chapter 39 · Buildings & Facilities on floors and tiles. How to read a dilution and residue are in Chapter 27 on neutral all-purpose cleaners, surfaces sensitive to alkali in Chapter 28 on mildly alkaline all-purpose cleaners, and how to check a data sheet in Chapter 26 on reading the safety data sheets of cleaning products. Surfactants are described in Chapter 21 on surfactants, colloids, and emulsions, and incompatible pairs of materials in Chapter 25 on chemical reactivity and incompatibility. Sanitizing after cleaning is in Chapter 7 · Biology & Microbiology on kitchen sanitation and critical control points, burnt-on residue in Chapter 35 on degreasers and burnt-on residue removers, and fryers in Chapter 2 · Commercial Kitchens on commercial gas fryers.

    Work outside the authority of kitchen cleaning staff and technicians: repairing tiles or grout, replacing or recoating a floor, applying an anti-slip treatment, handling a large spill of concentrate, and giving treatment other than first aid. Floor repair and replacement are handled by the flooring contractor appointed by the building manager, large spills by trained personnel or the emergency response team, and casualties by a doctor or the emergency services. The choice of product and rate is decided by the kitchen supervisor together with the supplier.

    What the product contains: three ingredients and pH 13 to 14

    According to the manufacturer’s safety data sheet for one product of this class, the floor cleaner is a liquid that is soluble in water, made for professional use. Three ingredients are listed, each at 1 to 5 percent. The pH of the undiluted product is 13 to 14, its relative density is 1.030 to 1.060, and its dilution is 1 : 5 to 1 : 100. The data sheet was issued on February 22, 2024, and is valid until February 21, 2029.

    Ingredient (name on the data sheet)CAS numberConcentration (%)
    Amines, coco alkyldimethyl, N-oxides61788-90-71 to 5
    Alkyl polyglycosides110615-47-91 to 5
    Monoethanolamine141-43-51 to 5

    At 25 °C, pH and pOH add up to 14, as in Chapter 15 on advanced acids and bases, so the hydroxide ion concentration can be calculated from the pH:

    [OH−]=10−(14−pH)[\text{OH}^-] = 10^{-(14 - \text{pH})}

    where [OH−][\text{OH}^-] is in mol/L. pH 13 means 0.1 mol/L and pH 14 means 1 mol/L, so the two ends of the range on that data sheet differ by a factor of ten (Example 1).

    For comparison, the Safer Choice standard of the United States EPA, a voluntary labeling program, requires the pH of the product as sold to be not less than 2 and not more than 11.5 to minimize the potential for irritation or injury to the skin and eyes. A concentrate at pH 13 to 14 lies 32 to 316 times above the line of 11.5 in hydroxide ion concentration. The words strong alkaline in the title of this chapter refer to that pH figure.

    The ingredient list contains two surfactants and one amine. An amine is a weak base, that is, a base that ionizes only partly in water, so those three ingredients do not yet explain a pH as high as 13 to 14 (Example 2). For the people who use it, what decides how the product is treated is its pH figure, and the origin of that alkalinity is a question for the supplier.

    Amine oxide and alkyl polyglycoside: surfactants that lift grease

    The EPA’s list of safer chemical ingredients lists CAS number 61788-90-7 as cocamine oxide and CAS number 110615-47-9 as C10 to C16 alkyl poly-D-glucosides, both in the surfactant class with a green circle, meaning a chemical that has been verified to be of low concern. The EPA standard defines a surfactant as an organic substance that has a water-loving group and a water-repelling group, so that it can reduce the surface tension of water, form emulsions and micelles, and adsorb at interfaces between water and solids.

    An amine oxide is an amine compound whose nitrogen atom is bonded to one oxygen atom. In this ingredient, that nitrogen carries two methyl groups and one long alkyl chain derived from coconut oil. An alkyl polyglycoside is a surfactant whose head is a few units of the sugar glucose and whose tail is an alkyl chain. In both, the alkyl chain goes into the grease and the head stays in the water, so the grease breaks up into fine droplets held in the water, as described in Chapter 21 on surfactants, colloids, and emulsions.

    HSE, the British occupational safety authority, writes that detergent is essential if a floor is contaminated with oil or grease, because water on its own, whether cold or warm, is not effective in removing it. On greasy floors, detergent is used to remove the oil and hold it in the water. Grease that is held in the water leaves the floor only when the water is lifted off as well. The green circle also concerns the ingredient, not the product: a surfactant of low concern does not make a concentrate at pH 13 to 14 safe to touch.

    Monoethanolamine

    Monoethanolamine, also called ethanolamine or 2-aminoethanol, is a colorless, viscous liquid with an ammonia-like odor that is miscible with water. NIOSH, the United States occupational safety and health institute, lists its exposure routes as inhalation, ingestion, and skin and eye contact, with symptoms of irritation of the eyes, skin, and respiratory system and drowsiness. The materials incompatible with it are strong oxidizers, strong acids, and iron, and ethanolamine may attack copper, brass, and rubber. The EPA list mentioned above gives ethanolamine a yellow triangle, meaning a chemical that meets the criteria for its class but still has some hazard profile issues. In detergents, ethanolamine is used as an alkaline buffer, as noted in Chapter 20 on organic chemistry for technicians.

    Threshold limit value (Indonesian nilai ambang batas, NAB) is the time-weighted average concentration that workers can accept without resulting in disease or health problems, for a time not exceeding 8 hours a day or 40 hours a week. Permitted short-term exposure (Indonesian pajanan singkat diperkenankan, PSD) is the concentration in air that must not be exceeded for a short exposure of no more than 15 minutes, at most 4 times in one working day. Permenaker (Minister of Manpower Regulation) 5/2018 sets the NAB for ethanolamine at 3 parts per million and the PSD at 6 parts per million, with the note irritation of the eyes and skin. As of November 2026 the regulation is listed as in force on JDIH Kemnaker, the ministry’s legal documentation site. The NIOSH figures are the same, and one part per million of ethanolamine equals 2.50 mg/m³. These figures concern vapor in the kitchen air, so the ventilation runs while the floor is being cleaned (Example 6).

    Dilution and the pH of the use solution

    The safety data sheet for a product of this class gives a dilution of 1 : 5 to 1 : 100, and this chapter gives no other rate. That range is wide: the strongest dose uses nearly 17 times as much product as the weakest dose (Example 3). Which dilution is used for which floor and which soil is read from the label. As in Chapter 27 on neutral all-purpose cleaners, the ratio 1 : n is read as one part product plus n parts water, so for a use solution of volume VV,

    Vp=V1+n,pHuse≥pH−log⁡(1+n)V_p = \frac{V}{1 + n}, \qquad \text{pH}_{use} \ge \text{pH} - \log(1 + n)

    where VpV_p is the volume of product in the same unit as VV. The right-hand side of the pH formula is the result for an unbuffered strong base at 25 °C. A solution whose alkalinity comes from a weak base or a buffer drops less, so that calculated result is a lower bound. With this model, the weakest solution of 1 : 100 from a concentrate at pH 14 is still at about pH 12 (Example 4). The pH of the use solution is therefore measured with pH paper or a pH meter, and the use solution is not treated as harmless just because it has been diluted.

    HSE writes that the concentration of detergent is critical to the cleaning result, that the manufacturer’s instructions are followed because too strong a solution can be as ineffective as too weak, and that dosing systems can eliminate error. At one food factory, the floor stayed greasy and slippery although a scrubber-drier was used often enough. The supervisor found that only one capful of detergent was being poured in, far below the manufacturer’s recommendation, and once the recommended concentration was used, the result improved rapidly. When diluting, the concentrated liquid is added to water, not the water to the concentrate.

    Slippery floors: contact time, rinsing, and drying

    People rarely slip on a clean, dry floor. According to HSE, contamination on the floor is involved in almost all slip accidents, and cleaning can be its source: smooth floors left damp after mopping are extremely slippery, and even a well-wrung mop leaves a thin film of water that is enough to make someone slip. A kitchen floor keeps its grip when wet if its surface is rough enough, loses that grip if it is not cleaned properly or often enough, and gets it back with good cleaning.

    Three stages decide the result.

    1. Contact time. The time the detergent is on the floor has been shown to have the biggest effect on cleanliness. HSE recommends a two-stage method for greasy floors: the detergent solution is put down and spread, left to work, then lifted in the second stage. Scouring or brushing increases its effect.
    2. Rinsing. The detergent is left long enough to release the grease before rinsing, and the dirty water is wrung into a separate bucket so that the dirt really leaves the floor. A squeegee on an oily floor can spread a thin layer of contamination over a wider area or force it into the surface.
    3. Drying. The floor is dried after cleaning. If that is not possible, people are kept off with barriers and “wet floor” signs until the floor is dry, and the signs are removed afterward. Warning cones only tell people that a hazard exists and do not prevent them from entering.

    Rinsing a strong alkaline cleaner has two more reasons. The ingredients listed on the data sheet do not evaporate with the water, so a solution left to dry leaves a film of surfactant, amine, and the grease that had been lifted (Example 5). That film also stays alkaline, and becomes a high-pH solution again as soon as the floor gets wet.

    HSE asks kitchen managers to ask the floor manufacturer about the best cleaning method, suitable detergents, and the correct concentrations, and to choose a time for routine cleaning that does not put people at risk. A floor that stays slippery although it is clean and dry is assessed according to Chapter 39 · Buildings & Facilities on floors and tiles.

    Eyes, skin, breathing, and first aid

    HSE notes that many cleaning substances are hazardous because they are corrosive and can cause skin and eye burns if they splash. HSE asks that the protective clothing provided always be worn when handling cleaning substances, especially concentrates, and that eye protection suitable for splashes, for example goggles or a visor, be worn if there is any danger of splashing. Where tap water is not available for eye irrigation, at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers is provided. For ethanolamine, NIOSH asks that skin and eye contact be prevented, that wet or contaminated clothing be removed, and that an eyewash be available.

    Pouring concentrate into a bucket is the moment of greatest risk to the eyes, and mopping keeps the hands wet with use solution for a long time. The glove material is read from the product data sheet, bearing in mind that ethanolamine may attack rubber. If the data sheet of a product at pH 13 to 14 does not list a hazard to the skin or states that personal protective equipment is not required, its contents are checked in the way given in Chapter 26 on reading the safety data sheets of cleaning products and the supplier is asked before the product is used. Wet work is explained in Chapter 41 · Biology & Microbiology on the skin and chemicals.

    First aid follows the product data sheet and the workplace procedure. Guidance from NIOSH for ethanolamine:

    1. Eyes. The eyes are immediately washed with large amounts of water while occasionally lifting the upper and lower lids, then the casualty is taken to medical attention immediately.
    2. Skin. The skin is promptly flushed with water. If the liquid penetrates the clothing, the clothing is immediately removed and the skin flushed, and the casualty gets medical attention if irritation persists after washing.
    3. Swallowed. The casualty is taken to medical attention immediately.
    4. Inhaled. The casualty is moved to fresh air at once, kept warm and at rest, and gets medical attention as soon as possible. If breathing has stopped, a trained rescuer gives artificial respiration and the emergency services are called.

    The label or the product data sheet is taken to the doctor, and what happens next is the decision of the medical staff.

    Handling and storage

    The manufacturer’s safety data sheet for one product of this class gives a storage temperature of 0 to 50 °C and names acids as incompatible materials. NIOSH classes strong acids and strong oxidizers as incompatible with ethanolamine, and amines form chloramines with hypochlorite, as covered in Chapter 20 on organic chemistry for technicians. This floor cleaner is therefore kept away from acidic descalers and is never mixed or used together with chlorine bleach.

    HSE gives guidance on storing and handling cleaning substances in hospitality:

    • Substances are kept in their original labeled containers. A decanting container is made of a suitable material, clean, and clearly marked with the instructions for use and the hazards.
    • Cleaning substances are never transferred into food or drink containers.
    • The storage place is away from heat, sunlight, foodstuffs, and members of the public, and all containers have lids.
    • Solutions are carried in lidded containers, especially if floors are wet or slippery.
    • Cleaning substances are never mixed, and are used only in well-ventilated areas.

    Buckets and mops that move from one product to another are rinsed first, and used mop water is disposed of through the sink or drain designated by the workplace. A small spill of concentrate is handled according to Chapter 6 · Safety on chemicals in technician work, and leftover product and empty containers according to the label and Chapter 35 · Water & Water Treatment on B3 waste.

    Worked example

    The figures in the examples below are practice figures, unless their origin is stated. A relative density of 1.045 is used as the midpoint of the range on the data sheet, and the molar mass of ethanolamine of 61.08 g/mol comes from Permenaker 5/2018.

    Example 1: what pH 13 and pH 14 mean. At pH 13, the hydroxide ion concentration is 10−(14−13)=0.110^{-(14 - 13)} = 0.1 mol/L, and at pH 14 it is 100=110^{0} = 1 mol/L. Against the line of pH 11.5, pH 13 is 1.5 units away, that is 101.5=3210^{1.5} = 32 times, and pH 14 is 2.5 units away, that is 102.5=31610^{2.5} = 316 times.

    Example 2: do those three ingredients explain the pH. One liter of product has a mass of 1.045×1,000=1,0451.045 \times 1{,}000 = 1{,}045 g. Ethanolamine at 1 percent means 10.45 g, that is 10.45/61.08=0.17110.45/61.08 = 0.171 mol/L, and 5 percent means 52.25 g, that is 52.25/61.08=0.85552.25/61.08 = 0.855 mol/L. Even if all the ethanolamine were ionized, the hydroxide ion concentration would be at most 0.855 mol/L, still below the 1 mol/L needed for pH 14. For pH 13 alone, the fraction that would have to be ionized is 0.1/0.855=120.1/0.855 = 12 percent at 5 percent and 0.1/0.171=580.1/0.171 = 58 percent at 1 percent, whereas a weak base ionizes only to a small extent. The three listed ingredients therefore do not yet explain pH 13 to 14.

    Example 3: product for one bucket. For 10 liters of use solution, a 1 : 5 dilution needs 10,000/(1+5)=1,66710{,}000/(1 + 5) = 1{,}667 mL of product and a 1 : 100 dilution needs 10,000/(1+100)=9910{,}000/(1 + 100) = 99 mL. The ratio is 1,667/99=16.81{,}667/99 = 16.8 times.

    Example 4: estimated pH of the use solution. With the model of an unbuffered strong base, a 1 : 5 dilution lowers the pH by log⁡6=0.78\log 6 = 0.78, so a concentrate at pH 13 becomes 13−0.78=12.2213 - 0.78 = 12.22 and a concentrate at pH 14 becomes 14−0.78=13.2214 - 0.78 = 13.22. A 1 : 100 dilution lowers the pH by log⁡101=2.00\log 101 = 2.00, to 13−2.00=11.0013 - 2.00 = 11.00 and 14−2.00=12.0014 - 2.00 = 12.00. These are lower bounds. Only one of those four results lies below 11.5, so the use solution is still handled with eye protection and gloves.

    Example 5: residue on the floor if it is not rinsed. After mopping, a 40 m² kitchen floor still carries a film of solution 0.05 mm thick. A film of 1 mm over 1 m² has a volume of 1 liter, so its volume is 40×0.05=2.040 \times 0.05 = 2.0 liters. At a dilution of 1 : 20, that film contains 2,000/(1+20)=95.22{,}000/(1 + 20) = 95.2 mL of product, with a mass of 95.2×1.045=99.595.2 \times 1.045 = 99.5 g. The three listed ingredients add up to 3 to 15 percent, that is 0.03×99.5=3.00.03 \times 99.5 = 3.0 g to 0.15×99.5=14.90.15 \times 99.5 = 14.9 g. If that film is left to dry, that much material stays on the floor each time it is mopped, together with the grease that had been lifted.

    Example 6: ethanolamine vapor and the NAB. An NAB of 3 parts per million equals 3×2.50=7.53 \times 2.50 = 7.5 mg/m³. A kitchen measuring 8 m by 6 m by 3 m has a volume of 8×6×3=1448 \times 6 \times 3 = 144 m³, so the NAB is equaled by 7.5×144=1,0807.5 \times 144 = 1{,}080 mg of ethanolamine in the air. A 10 liter bucket of 1 : 20 solution contains 10,000/21=47610{,}000/21 = 476 mL of product, with a mass of 476×1.045=497.4476 \times 1.045 = 497.4 g, with at most 0.05×497.4=24.90.05 \times 497.4 = 24.9 g of ethanolamine. That amount of 1,080 mg is only 1.08/24.9=4.31.08/24.9 = 4.3 percent of the contents of one bucket. This calculation gives a sense of scale, not an exposure estimate.

    Stop conditions

    1. Concentrate or use solution gets into the eyes: rinse at once with large amounts of water while holding the lids open, and take the casualty to the emergency services. The supervisor gets the product data sheet ready for the medical staff.
    2. The skin feels burned, turns red, or blisters after contact with the liquid, or liquid runs into a glove or a shoe: stop work, remove whatever is wet, and flush the skin with water. Examination and treatment are done by a doctor.
    3. The floor cannot yet be closed off from people passing, or the busy period of the kitchen has started: do not mop a wider area. The kitchen supervisor decides whether the area is closed or the work postponed.
    4. The floor stays slippery after it has been cleaned, rinsed, and dried, or tiles are loose and grout is pitted: close off that area and report it. Assessment and repair of the floor are done by the flooring contractor appointed by the building manager.
    5. A fryer or equipment holding hot oil stands along the path of the wet floor: do not mop around it until the kitchen supervisor confirms that the equipment is switched off and safe.
    6. Chlorine bleach, an acidic descaler, or another product has already been used on the same floor or in the same bucket, or there is a sharp odor: do not pour the floor cleaner, leave the area, and report to the supervisor. Anyone short of breath is taken to the emergency services.
    7. Coughing, stinging eyes, or drowsiness during work, or the kitchen exhaust fan is off: stop and move to fresh air. The building technician restores the ventilation.
    8. The floor finish, paint, or an aluminum strip softens, turns white, or fizzes when the solution touches it: rinse with water and stop. The building technician assesses the damage.
    9. More concentrate is spilled than the local spill kit can handle: keep people away and hand over to trained personnel or the emergency response team.
    10. The label is missing, the safety data sheet is absent or past its validity date, or its contents do not match the pH of the product: the product is not used until the supervisor obtains an explanation from the supplier.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    A floor cleaner is ordinary soap, so no protection is needed.

    Why is it wrong?

    The pH of the concentrate is 13 to 14, tens to hundreds of times above the line of 11.5 in hydroxide ion concentration. Eye protection and gloves are worn from the moment the jerry can is opened.

    Common misconception

    Stronger is cleaner.

    Why is it wrong?

    Too strong a solution can be as ineffective as too weak, and leaves more residue. The rate follows the label.

    Common misconception

    It has been diluted, so it is neutral.

    Why is it wrong?

    According to the lower-bound model, a 1 : 100 solution from a concentrate at pH 14 is still at about pH 12. The pH of the use solution is measured.

    Common misconception

    The floor has been mopped, so it is safe to walk on.

    Why is it wrong?

    A smooth floor that is still damp is extremely slippery, and even a well-wrung mop leaves a film of water. The floor is safe to walk on once it is dry.

    Common misconception

    A wet floor sign is enough.

    Why is it wrong?

    Warning cones only tell people that a hazard exists. People are kept off with barriers or the floor is dried.

    Common misconception

    Its surfactants are listed as safer ingredients, so the product is safe.

    Why is it wrong?

    That assessment concerns the ingredient, whereas the hazard of this concentrate comes from its pH.

    Chapter 39 · Buildings & Facilities on floors and tiles holds the floor types and slip testing that pair with this chapter. Chapter 27 on neutral all-purpose cleaners and Chapter 28 on mildly alkaline all-purpose cleaners cover milder floor cleaners, and Chapter 35 on degreasers and burnt-on residue removers covers a strong base for cooking equipment. Chapter 26 on reading the safety data sheets of cleaning products gives the way to check the data sheet that this chapter is based on.

    Exercises and worked solutions

    The figures in the questions are for practice.

    Try to answer first, then open the worked solution.

    1. An 8 liter bucket is to be filled with 1 : 40 use solution. How many milliliters of product are needed?

      Check my answer
      See the worked solution

      The product is 8,000/(1+40)=1958{,}000/(1 + 40) = 195 mL, and the rest is water. An amount that small is measured with a measuring jug or a dosing device, not estimated by eye.

    2. A concentrate at pH 13.5 is diluted 1 : 50. What is the estimated lower bound of the pH of the use solution, and is it already below 11.5?

      Check my answer
      See the worked solution

      The pH drops by log⁡51=1.71\log 51 = 1.71, to 13.5−1.71=11.7913.5 - 1.71 = 11.79. That figure is a lower bound and is still above 11.5, so the use solution is handled with eye protection and gloves.

    3. A worker pours the product twice as strong as the label says for a very greasy floor, then does not rinse it. What is wrong?

      Check my answer
      See the worked solution

      Too strong a solution can be as ineffective as too weak, and without rinsing the lifted grease and the cleaning ingredients stay behind as a film. A greasy floor is dealt with by the label rate, enough contact time, scrubbing, and rinsing.

    4. The floor in front of a row of fryers has just been mopped and is still damp, while the cooks are starting to come in for the busy period. What is done?

      Check my answer
      See the worked solution

      That area is closed off with barriers or the floor is dried before people pass, because a damp floor near hot oil is the situation in the opening case. Warning cones alone do not prevent people from entering.

    5. A 60 m² floor carries a film of 1 : 10 use solution 0.05 mm thick that is left to dry. How many grams of listed ingredients stay behind, if they add up to 3 to 15 percent of the product and the relative density of the product is 1.045?

      Check my answer
      See the worked solution

      The volume of the film is 60×0.05=3.060 \times 0.05 = 3.0 liters, containing 3,000/(1+10)=272.73{,}000/(1 + 10) = 272.7 mL of product with a mass of 272.7×1.045=285272.7 \times 1.045 = 285 g. The listed ingredients are 0.03×285=8.550.03 \times 285 = 8.55 g to 0.15×285=42.750.15 \times 285 = 42.75 g, so the floor is rinsed and the water lifted off.

    6. The data sheet of a floor cleaner states pH 13 to 14, but also states that personal protective equipment is not required. What do the worker and the supervisor do?

      Check my answer
      See the worked solution

      The worker wears eye protection and gloves according to the pH figure, not according to that statement, because pH 13 to 14 lies far above the line of 11.5. The supervisor checks the data sheet in the way given in Chapter 26 on reading the safety data sheets of cleaning products and asks the supplier for an explanation before the product is used.

    References

    External sources

    • Serious burn injuries lead to serious fine for fast food restaurant!hse.gov.uk
    • Slips and trips: The importance of floor cleaninghse.gov.uk
    • Preventing slips and trips in kitchens and food servicehse.gov.uk
    • Safer Chemical Ingredients Listepa.gov
    • EPA’s Safer Choice and Design for the Environment (DfE) Standardepa.gov
    • NIOSH Pocket Guide to Chemical Hazards - Ethanolaminecdc.gov
    • First Aid Procedures for Chemical Hazardscdc.gov
    • Safe use of cleaning substances in the hospitality industryhse.gov.uk
    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Strong alkaline kitchen floor cleaners: amine oxide, alkyl polyglycoside, and monoethanolamine, pH 13 to 14, dilution, slippery floors and rinsing, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/pembersih-lantai-dapur-alkali-kuat-amina-oksida-alkil-poliglikosida-dan-monoetanolamina-ph-13-sampai-14-pengenceran-lantai-licin-dan-pembilasan-serta-penanganan-dan-penyimpanan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    An 8 liter bucket is to be filled with 1 : 40 use solution. How many milliliters of product are needed?

    2

    A concentrate at pH 13.5 is diluted 1 : 50. What is the estimated lower bound of the pH of the use solution, and is it already below 11.5?

    3

    A worker pours the product twice as strong as the label says for a very greasy floor, then does not rinse it. What is wrong?

    Self-assessment progress0%

    Nearby chapters