By Kurnia · Published November 15, 2026 · Version 1 · 21 min read
Chlorine bleach for laundry
sodium dichloroisocyanurate powder and sodium hypochlorite liquid at 10 to 30 percent, available chlorine, the ban on mixing with acids and neutralizers, and handling and storage
In 1987, half a liter of household bleach mixed with a 4 percent acid cleaner emptied a hospital ward in California, and symptoms came back in a room that no longer smelled of chlorine. Laundries use stronger chlorine bleach, side by side with neutralizers and acid softeners. This chapter covers two forms of laundry chlorine bleach according to the manufacturer’s safety data sheet for one product of each form: a powder containing sodium carbonate and sodium dichloroisocyanurate dihydrate at 10 to 30 percent, and a sodium hypochlorite liquid at 10 to 30 percent with pH 12 to 14. It covers the differences between the two forms, the meaning and calculation of available chlorine, the ban on mixing with acids, ammonia, neutralizers, and other products, metals and flammable materials, hazards to the body, personal protective equipment, first aid, and handling and storage. Dosing rates and dispenser settings are not given. Wash programs, dispenser hoses, a room that smells of chlorine, large spills, and treatment of casualties are stated as work for other parties.
This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.
On December 25, 1987, at a state hospital in California, United States, a patient taking part in cleaning duties mixed approximately half a liter of bleach with one liter of a 4 percent phosphoric acid cleaner in a bucket. A pungent gas formed at once. The patient’s eyes stung, then fatigue set in. Four employees felt dizzy and nauseated, with stinging eyes and nose, headache, and chest tightness. The ward was evacuated until the floors had been rinsed and the air had been exchanged. More than an hour later, two employees entered an enclosed nursing office about 15 meters (50 feet) from the place where the bucket had been. The odor of chlorine could no longer be detected, yet the symptoms of both came back at once.
The bleach in that event was household bleach with 5.25 percent sodium hypochlorite, and the acid was only 4 percent. Hotel and hospital laundries use stronger materials on both sides: chlorine bleach as a powder or a concentrated liquid, and neutralizers and softeners that are acidic in the final rinse. All of them are kept in the same store and enter the machine through hoses that run side by side. Laundry staff need to know what is in the two forms of chlorine bleach, what available chlorine means, and why this product must not meet acids, ammonia, or neutralizer outside the process water.
Scope
This chapter covers two forms of chlorine bleach for commercial laundry, namely a powder containing an organic chlorine compound and a concentrated sodium hypochlorite liquid: their contents, pH, available chlorine, the ban on mixing, hazards to the body, first aid, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of each form. Other products can differ, so what applies in the workplace is the label and the safety data sheet of the product actually in use.
This chapter is learning material, not a work instruction. Dosing rates, the chlorine concentration in the process water, temperature, the length of the bleaching stage, and dispenser settings are not given; all of them are read from the product label, the supplier’s instructions, and the workplace procedure. How chlorine bleach works on stains, the effect of pH, fiber damage, and antichlor are in Chapter 8 · Laundry on oxidizers and finishing agents. The decomposition of sodium hypochlorite by heat and light and the threshold limit values for chlorine have already been covered in Chapter 41 on concentrated sodium hypochlorite and chlorinated sanitizing powder in the kitchen. Measuring chlorine in the process water is in Chapter 9 · Laundry on pH and chemical measurement throughout the cycle, programs and doses in Chapter 11 · Laundry on wash program architecture and Chapter 12 · Laundry on sorting, program design, and dose scaling, and dispensers in Chapter 1 · Chemical Dispensing on peristaltic dispensers and Chapter 2 · Chemical Dispensing and Chapter 3 · Chemical Dispensing on laundry dispensers.
Hazardous mixtures and their gas calculations are in Chapter 25 on chemical reactivity and incompatibility, how to check a data sheet in Chapter 26 on reading the safety data sheets of cleaning products, and wash room safety in Chapter 21 · Laundry on laundry occupational safety and health (K3). The acid products closest to chlorine bleach in a laundry are covered in Chapter 54 on laundry neutralizer based on sodium metabisulfite and Chapter 55 on acid laundry softener, and the other class of bleach in Chapter 52 on powdered oxygen bleach for laundry.
Work outside the authority of laundry operators and building technicians: setting doses and wash programs, adjusting or repairing dispensers and their hoses, entering a room that smells of chlorine, handling large spills or spills that have mixed with another product, and giving treatment other than first aid. Doses and programs are set by the laundry supervisor together with the supplier, dispensers are handled by the supplier’s technician, a room that smells of chlorine and large spills are handled by trained personnel or the emergency response team, and casualties are handled by a doctor or the emergency services.
Two forms of product: powder and liquid
The data below come from the manufacturer’s safety data sheet for one product of each form.
| Data | Powder | Liquid |
|---|---|---|
| Written use | cleaning product for industrial and professional use | laundry product for industrial and professional use |
| Ingredients listed | sodium carbonate, CAS number 497-19-8, 30 to 60 percent; an organic chlorine compound with CAS number 51580-86-0, 10 to 30 percent | sodium hypochlorite, CAS number 7681-52-9, 10 to 30 percent |
| Form | opaque white powder with a chlorine odor, partially soluble in water | clear, light yellow liquid with a chlorine odor |
| pH | 9.9 to 10.3 in a 1 percent solution | 12.0 to 14.0 in the undiluted product |
| Relative density | 1.0 to 1.15 | 1.200 to 1.230 |
| Written classification | eye irritation category 2A; specific target organ toxicity after single exposure category 3, respiratory tract | skin corrosion category 1B; serious eye damage category 1; acute aquatic hazard category 1 |
| Dilution information | not written | automatic setting with a dispenser |
| Storage temperature | 0 to 50 °C | 0 to 40 °C |
| Incompatible materials | acid | acid and metals |
| Validity of the data sheet | November 21, 2024 to November 20, 2029 | 2024 to 2027 |
The difference in pH between the two products explains part of the difference in their classification (Example 4). The data sheet for the powder gives no dosing rate, and the data sheet for the liquid mentions only automatic setting with a dispenser, so this chapter gives no dosing rate for either. Both data sheets ask for the product to be kept away from reducing agents and flammable materials.
The organic chlorine compound in the powder
The second ingredient of the powder is listed with CAS number 51580-86-0 and the name sodium dichloro-s-triazinetrione dihydrate. WHO records that CAS number as the dihydrate form of sodium dichloroisocyanurate, which is also known as sodium dichloro-s-triazine trione and sodium troclosene. Sodium dichloroisocyanurate, abbreviated NaDCC, is the sodium salt of a chlorinated hydroxytriazine that is used as a source of free chlorine in the form of hypochlorous acid.
When it enters water, NaDCC rapidly hydrolyzes and releases free chlorine. Part of its chlorine stays bound to isocyanurate as a reservoir. When hypochlorous acid is consumed by organic material, that reservoir rapidly dissociates and releases new hypochlorous acid.
In the dry state NaDCC is very stable, even at high temperatures. Once dissolved, NaDCC forms an equilibrium that contains the same active species as hypochlorite, and it is as unstable as liquid hypochlorite. The powder therefore keeps only while it is dry, and a bucket left open in a damp wash room or a wet scoop brings water into the container. The sodium carbonate in the powder is a base, covered in Chapter 49 on laundry alkali builders, and gives the powder solution a pH of about 10.
Available chlorine: a common unit for two products
The two products cannot be compared by the percentage of their active ingredient, because the active ingredients are different. Available chlorine is a measure of the oxidizing capacity of a chlorine product, expressed as the equivalent mass of chlorine. WHO states that the oxidizing capacity of hypochlorite solutions is expressed as either a percentage of available chlorine or parts per million of available chlorine. Chapter 17 on advanced redox, which writes the term in Indonesian as klorin tersedia, derives the figure for sodium hypochlorite. One mole of sodium hypochlorite is equivalent to one mole of chlorine, so
where is the mass fraction of sodium hypochlorite, is the molar mass of chlorine, 70.90 g/mol, and is the molar mass of sodium hypochlorite, 74.44 g/mol. A liquid at 10 to 30 percent is therefore equivalent to 9.5 to 28.6 percent available chlorine (Example 1).
For NaDCC, WHO gives the figure directly: the dihydrate form contains 55 to 56 percent free available chlorine, and the anhydrous form 62 to 64 percent. A powder containing 10 to 30 percent of the dihydrate form is therefore equivalent to 5.5 to 16.8 percent available chlorine (Example 2). That range spans a factor of three, so what is used for dosing is the figure on the label and on the supplier’s technical data sheet.
Available chlorine also changes in storage. WHO records that liquid hypochlorite decays on storage at a rate that depends mainly on temperature, so its available chlorine content is uncertain, and its dilute solutions last only about one day. The chlorine concentration in the process water is therefore measured, not calculated from the label alone.
The ban on mixing: acids, ammonia, neutralizers, and other products
Both safety data sheets warn that this product must not be mixed with acid or ammonia.
Acids. When sodium hypochlorite meets an acid, chlorine gas and water are formed. The chlorine gas then reacts with water, including the water in the eyes and airways, to form hydrochloric acid and hypochlorous acid. In the Great Britain classification and labeling regulation, a sodium hypochlorite solution with 5 percent active chlorine or more carries the statement that contact with acids liberates toxic gas. The powder forms the same chlorine species in water, so this ban applies to both forms. In a laundry, those acids are the neutralizer and the acid softener in the final rinse.
Ammonia. When bleach meets compounds that contain ammonia, what forms are monochloramine and dichloramine, which can cause tearing, respiratory tract irritation, and nausea. The UK Health Security Agency (UKHSA) writes the same thing: sodium hypochlorite liberates chloramines if it is mixed with ammonia. The gas is different from chlorine gas, but the ban is the same.
Neutralizers and reducing agents. UKHSA records sodium hypochlorite as a strong oxidizing agent that reacts with flammable materials and reducing agents, generating a fire and explosion hazard. HSE, the British occupational safety authority, gives a basic storage rule: acids are kept separate from alkalis, and oxidizing agents from reducing agents. A laundry neutralizer based on sodium metabisulfite stands on the opposite side from chlorine bleach under both of those rules, because it is acidic and reducing, as covered in Chapter 8 · Laundry on oxidizers and finishing agents. Inside the machine, the neutralizer does use up residual chlorine, but that happens in process water that is already dilute and after rinsing. Outside the machine, in concentrated form, the two products must not meet.
Other products. Two different bleaches also react with each other, so chlorine bleach is not mixed with oxygen bleach. HSE gives one short rule for hospitality workers: never mix cleaning substances.
This ban is broken unintentionally through a scoop or measuring jug that is shared, a used bucket that still holds the remains of another product, and a dispenser hose connected to the wrong jerry can. The liquid left in one hose is already enough to release several liters of chlorine gas (Example 6). HSE asks for chemical pipework to be labeled or color marked according to the chemical it conveys.
Metals, flammable materials, and fabrics
On the data sheet for the liquid, metals are listed as an incompatible material. UKHSA records that sodium hypochlorite solution attacks many metals, including copper. WHO writes that hypochlorites can cause severe corrosion of metals, and that hypochlorites are inactivated by organic matter. Containers, funnels, and measuring tools made of metal are therefore not used for this product. On linen, that organic matter is the soil that has not yet been lifted, so the bleach is used up by it first.
As an oxidizing agent, chlorine bleach is also kept away from flammable materials. HSE writes that an existing fire may be made considerably worse if an oxidizing agent is involved. Cardboard, oily rags, and solvents are not kept on the same shelf.
Which fabrics may be exposed to chlorine bleach, and what damage it does to fibers and colors, is covered in Chapter 8 · Laundry on oxidizers and finishing agents.
Hazards to the body and personal protective equipment
The concentrated liquid is a contact hazard. According to UKHSA, bleach with a hypochlorite concentration above 10 percent is corrosive, and swallowing any amount of industrial-strength bleach may cause significant toxicity. Alkaline solutions can damage all layers of the eye and are treated as an eye emergency, and alkali injuries to the skin may be painless at first, so that treatment is delayed. The classification of skin corrosion category 1B and serious eye damage category 1 on the data sheet for the liquid is consistent with that.
The powder is a dust hazard. Its classification names eye irritation and respiratory tract irritation. HSE asks for powder always to be taken with a scoop, never by hand.
The third hazard is gas from a wrong mixture. CDC, the United States disease control agency, records that chlorine gas touching moist tissues such as the eyes, throat, and lungs forms an acid that injures those tissues. The symptoms include tearing eyes, a burning feeling in the nose and throat, coughing, chest tightness, and shortness of breath. People with asthma or other lung diseases may be more sensitive, and this gas is heavier than air, so it sinks to low places. In the opening case, symptoms came back in a room that no longer smelled of chlorine, so the absence of odor is not a sign of safety.
HSE guidance:
- Eye protection suitable for splash risks, for example goggles or a visor, is worn if there is any danger of splashing, and rubber gloves are checked for holes, tears, and thin patches.
- Corrosive liquids are not poured straight from the container into a bucket or measuring jug; what is used is a valve, a pump, or an enclosed system, and running water for dousing a casualty is available near the dispensing point.
The type of glove material and respiratory protection are read from the product’s data sheet and are covered in Chapter 5 · Safety on personal protective equipment.
First aid
First aid follows the label, the product’s data sheet, and the workplace procedure. HSE guidance for chemical injuries and CDC guidance for chlorine:
- Eyes. The eye is flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then the casualty is sent to hospital.
- Skin. The affected area is flooded with water for 20 minutes, and flooding can continue on the way to hospital. Contaminated clothing that is not stuck to the skin is removed, and the first aider avoids becoming contaminated as well.
- Swallowed. Vomiting is not forced, and the casualty is taken at once to a doctor or the emergency services together with the product label.
- Gas inhaled. The casualty leaves the place at once for fresh air, and other people get out of the building. If the eyes are burning, they are washed for 10 to 15 minutes, and medical help is sought right away. If breathing has stopped, a trained first aider gives artificial respiration and the emergency services are called.
UKHSA asks unprotected responders not to approach a casualty incapacitated in a contaminated place, because the responder may become a casualty as well. Its guidance for healthcare professionals also prohibits giving neutralizing chemicals to a casualty who has swallowed concentrated bleach, because the heat of the neutralization reaction may increase the injury. What happens next is a decision for medical personnel.
Handling and storage
The safety data sheets give a storage temperature of 0 to 50 °C for the powder and 0 to 40 °C for the liquid, and ask for both to be kept away from reducing agents and flammable materials. Other guidance:
- Substances are stored in their original labeled containers with lids, away from heat, sunlight, foodstuffs, and members of the public. The manufacturer’s storage instructions are checked because some products must be stored separately.
- The store is organized in marked bays, so that incompatible substances are not in the same bay.
- Chlorine bleach and acid products each have their own containment tray, measuring jug, scoop, and funnel.
- Jerry cans and dispenser hoses carry the same marking, and the label of a new jerry can is matched before the hose is connected.
The powder bucket is closed at once after measuring, and its scoop is dry. Liquid stock that arrived first is used first, because its strength falls in storage. A small spill is handled according to Chapter 6 · Safety on chemicals in technician work. A spill is not soaked up with cloth, paper, or sawdust, because an oxidizing agent reacts with flammable materials, and it is not flushed into a drain. Leftover product and empty containers are handled according to the label and Chapter 35 · Water & Water Treatment on B3 waste in hotels, laundries, and workshops.
Worked example
Figures in the examples below are practice figures, unless their origin is stated. Ingredient contents come from the data sheets and are read as percent by mass. A relative density of 1.215 for the liquid is used as the midpoint of the range of 1.200 to 1.230, and the molar volume of a gas is 24.5 L/mol at 25 °C and 1 atm. The results are used to understand magnitudes, not for dosing.
Example 1: available chlorine in the liquid. One liter of liquid has a mass of g. At 10 percent, the sodium hypochlorite is g and the available chlorine is g. At 30 percent, g of sodium hypochlorite is equivalent to g of available chlorine. Relative to the mass of the liquid, that is percent to percent.
Example 2: available chlorine in the powder. The dihydrate form contains 55 to 56 percent available chlorine. A powder at 10 percent is equivalent to percent, and a powder at 30 percent is equivalent to percent available chlorine. One kilogram of powder carries g to g of available chlorine.
Example 3: the effect of the content range on a solution. A quantity of 50 g of powder is dissolved in 100 L of water. The available chlorine is g to g, so the concentration is mg/L to mg/L. The same measured amount can give concentrations that differ by a factor of three. The figure of 50 g is not a dosing rate; the dosing rate is taken from the label, and the result is checked with test strips.
Example 4: hydroxide ions at two pH values. At 25 °C, pOH and . A liquid with pH 12.0 contains mol/L, and a liquid with pH 14.0 contains mol/L. A 1 percent solution of the powder with pH 10.3 contains mol/L. The hydroxide ion concentration of the undiluted liquid is at least times the concentration in that powder solution.
Example 5: upper limit of chlorine gas from powder that meets acid. One hundred grams of powder at 30 percent carries g of available chlorine, that is, mol. If all of it is released as chlorine gas, its volume is L. In a chemical store measuring 3 m by 2 m by 2.5 m, that is, m³ or 15,000 L, the concentration is parts per million if it is evenly mixed. The CDC report in the opening case states that a level of 3 parts per million may already cause extreme irritation of the eyes and respiratory tract. That figure of 387 is an upper limit, but one percent of it alone already exceeds 3 parts per million.
Example 6: liquid left in a dispenser hose. A suction hose 3 m long with an inside diameter of 6 mm holds cm³, that is, 85 mL of liquid. At 10 percent, its contents are g of sodium hypochlorite or mol. If that hose is moved to a jerry can of acid neutralizer and the liquid left in it is pushed in, the chlorine gas released is at most L. A hose is not moved from one product to another.
Stop conditions
- A sharp odor of chlorine is noticed, or the eyes and throat sting, in the store or in the wash room: stop work, leave the room for fresh air, and clear the surrounding rooms. Do not re-enter even if the odor has gone. The supervisor calls the building emergency response team or the fire department, and anyone short of breath is taken to the emergency services.
- There is neutralizer, acid softener, another acid product, an ammonia product, or oxygen bleach in the bucket, measuring jug, scoop, funnel, or sink that is about to be used, or its previous contents are not known: do not pour or measure chlorine bleach. The laundry supervisor decides the containers and the work sequence.
- A jerry can or dispenser hose is unlabeled, or the marking on the hose does not match the label on the jerry can: do not connect it. The supplier’s technician checks the connections.
- Concentrated liquid gets into the eyes or onto the skin, powder gets into the eyes, or the product is swallowed: give first aid and take the casualty to a doctor or the emergency services.
- A dispenser hose, pump, or connection is dripping or leaking: keep people away from the drips and do not dismantle the dispenser. The supplier’s technician carries out the repair.
- The dosing rate is not written on the label or in the procedure, or chlorine test strips are not available: do not measure by guesswork. The supervisor asks the supplier for a written rate.
- The powder is wet or caked, a jerry can is leaking or bulging, or the product has been stored near heat: do not use it before the supervisor has checked it together with the supplier.
- A spill is larger than the local spill kit can handle, has reached an acid product or neutralizer, or is flowing into a drain: clear the area and hand over to trained personnel or the emergency response team.
- The label is missing, the safety data sheet is absent or past its validity date, or the ventilation of the place where the product is measured is dead: the product is not used until the supervisor has resolved it with the supplier or the building technician.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
Powder is safer than liquid because it is dry and its pH is lower.
Why is it wrong?
The powder carries 5.5 to 16.8 percent available chlorine, and one hundred grams of it can release several liters of chlorine gas if it meets acid. Its dust irritates the eyes and airways.
Common misconception
Chlorine bleach and ammonia produce chlorine gas.
Why is it wrong?
What forms are chloramines. The gas is different, but both irritate the airways, and the ban is just as firm.
Common misconception
Neutralizer can be poured onto leftover bleach so that its chlorine is used up.
Why is it wrong?
Neutralizer is acidic and reducing. Neutralization of residual chlorine happens only inside the machine, in dilute process water; in a bucket or a jerry can, those two concentrated products must not meet.
Common misconception
Once the odor has gone, the room is safe.
Why is it wrong?
In the event in California, symptoms came back in a room that no longer smelled of chlorine. A room is declared safe by trained personnel, not by the nose.
Common misconception
The percentage of sodium hypochlorite is the same as the percentage of available chlorine.
Why is it wrong?
The available chlorine of sodium hypochlorite is 0.952 times its mass fraction, and for the powder the figure depends on its chlorine compound. Two products are compared in the same unit.
Links to other chapters
Chapter 8 · Laundry on oxidizers and finishing agents explains how chlorine bleach works, and Chapter 41 on concentrated sodium hypochlorite and chlorinated sanitizing powder in the kitchen covers the decomposition of hypochlorite and the threshold limit values for chlorine. Chapter 54 on laundry neutralizer based on sodium metabisulfite and Chapter 55 on acid laundry softener cover the products that must not meet the products in this chapter.
Exercises and worked solutions
The figures in the problems are for practice. The relative density of the liquid is taken as 1.215, and the dihydrate form of the chlorine compound in the powder is taken to contain 55 to 56 percent available chlorine.
Try to answer first, then open the worked solution.
A sack holds 25 kg of powder with 20 percent chlorine compound. How many kilograms of available chlorine does it carry?
Check my answer
See the worked solution
The chlorine compound is kg, so the available chlorine is kg to kg. One sack carries almost three kilograms of available chlorine, so that sack is stored as an oxidizing agent.
The label of a liquid states 12 percent sodium hypochlorite. How many grams of available chlorine are in one liter?
Check my answer
See the worked solution
The sodium hypochlorite in one liter is g, so the available chlorine is g. That figure holds for the concentration on the label; the strength of a jerry can that has been stored for a long time is lower.
At the end of a shift, an operator is about to pour leftover neutralizer from a measuring jug into the bucket that was used earlier for chlorine bleach, so that the residual chlorine is neutralized. What is wrong?
Check my answer
See the worked solution
Neutralizer is acidic and reducing, so the bleach left in the bucket can release chlorine gas when it meets concentrated neutralizer. The leftovers of each product are handled separately according to the label, and buckets and measuring jugs are not shared.
A 1 percent solution of the powder is measured at pH 10.1. What is its hydroxide ion concentration, and how many times lower is it than in a liquid with pH 12.0?
Check my answer
See the worked solution
The pOH of that solution is , so mol/L. A liquid with pH 12.0 contains 0.010 mol/L, that is, times as much.
A suction hose 2 m long with an inside diameter of 8 mm is still full of liquid at 30 percent. What is the upper limit of chlorine gas if its contents meet acid?
Check my answer
See the worked solution
The hose holds cm³ or 101 mL. The sodium hypochlorite is g or mol, so the chlorine gas is at most L. A hose that still holds liquid is not disconnected or moved by the operator.
In the store, a bucket of chlorine bleach powder stands open on the same shelf as jerry cans of neutralizer and acid softener, above a stack of cardboard, and one measuring jug is used for all products. What has to change, and who decides?
Check my answer
See the worked solution
The bucket is closed and moved to a bay separate from the acid products and the neutralizer, kept away from the cardboard because oxidizing agents are not stored with flammable materials, and each product gets its own measuring jug. The layout of the store is decided by the laundry supervisor together with the supplier.
References
External sources
- Epidemiologic Notes and Reports Chlorine Gas Toxicity from Mixture of Bleach with Other Cleaning Products -- Californiacdc.gov
- Sodium Dichloroisocyanurate in Drinking-water: Background document for development of WHO Guidelines for Drinking-water Qualitywho.int
- Decontamination and waste managementiris.who.int
- Sodium hypochlorite: incident managementassets.publishing.service.gov.uk
- Chlorinecdc.gov
- Safe use of cleaning substances in the hospitality industryhse.gov.uk
- Basic advice on first aid at workhse.gov.uk
- Chemicals - safe use and handlinghse.gov.uk
Revision history
| Date | Version | Change |
|---|---|---|
| November 15, 2026 | 1 | First published |
How to cite
Kurnia (2026). Chlorine bleach for laundry: sodium dichloroisocyanurate powder and sodium hypochlorite liquid at 10 to 30 percent, available chlorine, the ban on mixing with acids and neutralizers, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/pemutih-klor-untuk-laundry-serbuk-natrium-dikloroisosianurat-dan-cairan-natrium-hipoklorit-10-sampai-30-persen-klor-tersedia-larangan-mencampur-dengan-asam-dan-penetral-serta-penanganan-dan-penyimpanan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.
A sack holds 25 kg of powder with 20 percent chlorine compound. How many kilograms of available chlorine does it carry?
The label of a liquid states 12 percent sodium hypochlorite. How many grams of available chlorine are in one liter?
At the end of a shift, an operator is about to pour leftover neutralizer from a measuring jug into the bucket that was used earlier for chlorine bleach, so that the residual chlorine is neutralized. What is wrong?
Nearby chapters
Reading order by shelf: Chemistry · Chapter 54.
Reading order by shelf: Chemistry · Chapter 52.