By Kurnia · Published November 15, 2026 · Version 1 · 21 min read
Powdered oxygen bleach for laundry
sodium percarbonate and sodium carbonate, release of hydrogen peroxide, solution pH, oxidizing properties and moisture, and handling and storage
Oxygen bleach powder in a laundry store cakes because of a wet scoop, and a bucket sealed after its contents became damp bulges. This chapter covers powdered oxygen bleach for laundry from the side of its chemistry: sodium carbonate at 30 to 60 percent and sodium carbonate peroxyhydrate, that is, sodium percarbonate, at 30 to 60 percent according to the manufacturer’s safety data sheet for one product of this class, the release of hydrogen peroxide in water, why its solution has a pH of about 11, oxidizing properties, decomposition by moisture, heat, metals, and time, incompatible materials, hazards to the eyes, skin, and airways, personal protective equipment, first aid, and handling and storage. Dosing rates and dispenser settings are not given. Wash programs, powder that is heating up, large spills, fires, and treatment of casualties are stated as work for other parties.
This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.
In the laundry chemical store of a hotel, a bucket of powdered oxygen bleach stands open near the door of the damp wash room. Its scoop is washed every afternoon, then put back into the bucket while still wet. Two weeks later the top layer of the powder has hardened into lumps. The operator breaks the lumps up by hand, the dust rises to the face, and the operator’s eyes sting so badly that they have to be rinsed for a long time at the sink. A second bucket on the same shelf was sealed tightly after its contents had already become damp, and then its lid bulged.
Both events come from one property: this powder carries hydrogen peroxide in solid form, and a little water is enough to start releasing it. The report of an FAO and WHO technical meeting on milk preservation records the same thing about its active ingredient: percarbonate takes up water vapor, and the oxygen it releases can make packaging bulge. Inside the washing machine, that release is what is wanted; in the store and in the operator’s eyes, that release becomes a problem. Laundry staff need to know what is in the powder, what happens when the powder meets water, why its solution is alkaline, and which materials must not be near it.
Scope
This chapter covers one class of product, namely oxygen bleach in powder form for commercial laundry: its contents, the release of hydrogen peroxide, solution pH, oxidizing properties, the effect of moisture, incompatible materials, hazards to the body, first aid, and handling and storage. The product data come from the manufacturer’s safety data sheet for one product of this class. Other products can differ, so what applies in the workplace is the label and the safety data sheet of the product actually in use.
This chapter is learning material, not a work instruction. Dosing rates, temperature, the length of the bleaching stage, and dispenser settings are not given; all of them are read from the product label, the supplier’s instructions, and the workplace procedure. How oxygen bleach works on stains, its pH and temperature requirements, activators, and fiber damage are in Chapter 8 · Laundry on oxidizers and finishing agents. Alkali chemistry is in Chapter 6 · Laundry on cleaning chemistry, pH inside the machine in Chapter 9 · Laundry on pH and chemical measurement throughout the cycle, programs and doses in Chapter 11 · Laundry on wash program architecture and Chapter 12 · Laundry on sorting, program design, and dose scaling, and dispensers in Chapter 1 · Chemical Dispensing on peristaltic dispensers and Chapter 2 · Chemical Dispensing and Chapter 3 · Chemical Dispensing on laundry dispensers.
How to check a data sheet is in Chapter 26 on reading the safety data sheets of cleaning products, hazardous mixtures in Chapter 25 on chemical reactivity and incompatibility, labels and spills in Chapter 6 · Safety on chemicals in technician work, and wash room safety in Chapter 21 · Laundry on laundry occupational safety and health (K3). The products that must not meet this powder are covered in Chapter 53 on chlorine bleach for laundry, Chapter 54 on laundry neutralizer based on sodium metabisulfite, and Chapter 55 on acid laundry softener.
Work outside the authority of laundry operators and building technicians: setting doses and wash programs, adjusting or repairing dispensers, handling large spills or powder that is heating up and smoking, fighting a fire in the chemical store, and giving treatment other than first aid. Doses and programs are set by the laundry supervisor together with the supplier, dispensers are handled by the supplier’s technician, large spills and heating powder are handled by trained personnel or the emergency response team, fires are handled by the fire department, and casualties are handled by a doctor or the emergency services.
What the product contains: sodium carbonate and sodium carbonate peroxyhydrate
According to the manufacturer’s safety data sheet for one product of this class, powdered oxygen bleach is an opaque white, odorless powder that is partially soluble in water. The data sheet states its use as a laundry detergent for industrial and professional use. Two ingredients are listed: sodium carbonate, CAS number 497-19-8, at 30 to 60 percent, and sodium carbonate peroxyhydrate, CAS number 15630-89-4, also at 30 to 60 percent. The pH of its 1 percent solution is 11.1 to 11.5. The classification written for the product as sold is acute oral toxicity category 4, skin corrosion category 1B, and serious eye damage category 1. The data sheet was issued on September 29, 2024 and is valid until September 28, 2029. On dilution, all that is written is that the product is sold ready to use, with no dosing figure. The two ranges of 30 to 60 percent cannot both be at their upper limit, because the total would exceed 100 percent.
Sodium carbonate, with the formula Na₂CO₃, is the sodium salt of carbonic acid and is among the carbonates used commercially in the largest quantities. Sodium percarbonate is the common name of sodium carbonate peroxyhydrate. The Safer Choice chemical ingredients list of the EPA, the United States environmental protection agency, records CAS number 15630-89-4 under that name, as a compound of sodium carbonate with hydrogen peroxide in the ratio 2 : 3, in the functional class of oxidants. Hydrogen peroxide, with the formula H₂O₂, is a strong oxidizing agent used as a bleach and disinfectant.
From that 2 : 3 ratio, the mass fraction of hydrogen peroxide in pure sodium percarbonate can be calculated:
where is the mass fraction of hydrogen peroxide (dimensionless), is the molar mass of hydrogen peroxide, 34.0 g/mol, and is the molar mass of sodium carbonate, 106.0 g/mol. The result is 32.5 percent (Example 1). This figure is the theoretical limit for the pure compound; the peroxide content of the product in use is read from its technical data sheet.
Release of hydrogen peroxide in water
Sodium percarbonate is a way of carrying hydrogen peroxide without a jerry can of liquid. Guidance from the Environment Agency, the British environmental agency, on the use of peroxide in waterways calls it a solid form of peroxide. The FAO and WHO report states that hydrogen peroxide is generally added in the form of granulated sodium carbonate peroxyhydrate, which releases its active agents more slowly than liquid hydrogen peroxide. When the powder dissolves, two substances enter the wash water: sodium carbonate, which makes the solution alkaline, and hydrogen peroxide, which bleaches.
Hydrogen peroxide itself is not stable. In solution, its concentration falls slowly because it decomposes into water and oxygen gas:
Two moles of hydrogen peroxide produce one mole of oxygen gas. The UK Health Security Agency (UKHSA) records that hydrogen peroxide decomposes under the influence of light and on warming while releasing oxygen, and names heat and metal catalysts as triggers of a fire and explosion hazard. The oxygen gas that escapes is not what bleaches. What works on stains is the hydrogen peroxide that has not yet decomposed, and how it works is explained in Chapter 8 · Laundry on oxidizers and finishing agents. Peroxide that decomposes beforehand in the store is bleaching power lost before it reaches the machine.
In the store, water vapor from the air, drips from a wet scoop, or splashes from the floor are enough to wet the surface of the granules, and peroxide that has met water begins to decompose. The peroxide from one kilogram of powder can release tens of liters of oxygen gas if it decomposes completely (Example 3).
Solution pH: why about 11
Carbonate is a moderately strong base. The carbonate ion takes a hydrogen ion from water and leaves a hydroxide ion:
where is the second ionization constant of carbonic acid, , at 25 °C, and is the carbonate concentration in mol/L. The square-root formula is an approximation for an ideal dilute solution, so its result is an estimate. The carbonate in the solution comes from two ingredients at once, namely free sodium carbonate and the sodium carbonate released by the percarbonate. For a 1 percent solution, that calculation gives a pH of about 11.5 (Example 4), at the upper end of the range of 11.1 to 11.5 on the data sheet. Hydrogen peroxide is a very weak acid, with an ionization constant of , so its presence lowers that pH slightly.
The Environment Agency records the same thing from the other side: this solid form of peroxide can raise the pH of the water in which it decomposes. For the operator, an oxygen bleach solution is an alkaline solution, like the sodium carbonate solution in Chapter 49 on laundry alkali builders, so eye protection and gloves are still worn even though this product has no odor. The pH inside the machine is determined by the whole formula and is measured, not guessed from one product.
Oxidizing properties, moisture, and decomposition
An oxidizing agent is a substance that takes electrons from another substance in a redox reaction. HSE, the British occupational safety authority, writes that an existing fire may be made considerably worse if an oxidizing agent is involved, because many substances of this class break down when heated and the oxygen released increases the rate of burning. The Environment Agency writes something similar about peroxide: the substance itself does not burn, but it contributes to the combustion of other materials, and that also holds for its solid form.
Four things speed up the decomposition of the powder in storage.
Moisture. Percarbonate takes up water vapor, and peroxide that has met water decomposes while releasing oxygen. Damp powder cakes and loses its bleaching power. In a container sealed tightly after its contents have become damp, the oxygen gas raises the pressure, as in the second bucket in the opening case.
Heat and sunlight. Hydrogen peroxide decomposes on warming and under light. The Environment Agency asks for the solid form to be stored in a cool, dry place, protected from direct sunlight, and away from heat sources.
Metals and contamination. A rusty scoop or powder contaminated with another material brings metals and organic materials into the bucket, two groups that the Environment Agency asks to be kept away from solid peroxide. HSE asks for scoops and buckets used for chemicals always to be clean and dry, because cross-contamination between incompatible substances may result in a violent reaction. Product that has been taken out is also not returned to its container.
Time. HSE asks that storage time limits not be exceeded, particularly for solid oxidizing agents, because the longer a substance is stored the more likely it is to decompose. Stock that arrived first is used first, and a bucket that has been opened is dated.
Incompatible materials
The safety data sheet for a product of this class names one incompatible material, namely acid. The list from public bodies is longer.
| Material | What happens | Rule of thumb |
|---|---|---|
| Acids: neutralizers, acid softeners, rust removers | carbonate reacts with acid to form a salt, water, and carbon dioxide gas (Example 6) | never mixed; stored separately; scoops and buckets not shared |
| Flammable and organic materials: oily rags, cardboard, solvents | an oxidizing agent contributes to the combustion of other materials | not stored together; spills not swept up with trash |
| Reducing agents, for example a neutralizer based on sodium metabisulfite | oxidizing agents and reducing agents are kept apart as a basic storage rule | separate shelves and containment trays |
| Metals and heat | trigger the decomposition of peroxide | clean, dry plastic scoops and containers; away from steam pipes and dryers |
| Chlorine bleach | two different bleaches react with each other, as explained in Chapter 8 · Laundry on oxidizers and finishing agents | not mixed and not measured with the same tool |
HSE gives one short rule for hospitality workers: never mix cleaning substances. In a laundry, that prohibition is most easily broken through a scoop used for two products and a used bucket filled with another product.
Hazards to the body, dust, and personal protective equipment
The classification of skin corrosion category 1B and serious eye damage category 1 on the data sheet means that the powder and its concentrated solution can damage tissue. A carbonate solution is alkaline, and chemical burns from bases are covered in Chapter 41 · Biology & Microbiology on the skin and chemicals. According to UKHSA, on the skin hydrogen peroxide can whiten the skin and cause inflammation, blistering, and burns. In the eyes, weak solutions cause burning, redness, and blurred vision, while solutions of 10 percent or more can cause ulceration or perforation of the cornea.
A concentration that high is not reached in wash water, but it can be reached in wet powder. In the Great Britain classification and labeling regulation quoted by UKHSA, a hydrogen peroxide solution of 8 to less than 50 percent falls under serious eye damage category 1, and a concentration of 5 to less than 8 percent falls under serious eye irritation. A handful of powder hit by a splash of water becomes a paste with a peroxide concentration in that range (Example 5), and that paste is strongly alkaline at the same time.
Dust is the third route. HSE includes soda ash, that is, sodium carbonate, and bleach among the substances that can cause skin irritation, itchy and stuffy noses, sneezing, and sore eyes. The Environment Agency records that solid peroxide irritates the mucous membranes, eyes, and skin, just like its liquid form.
For hydrogen peroxide in air, the workplace exposure limit in Britain is 1 part per million or 1.4 mg/m³ for an 8-hour reference period, and 2 parts per million or 2.8 mg/m³ for a 15-minute reference period. Those figures are a British rule. HSE guidance for cleaning substances in hospitality:
- Powder is always taken with a scoop, never by hand.
- Eye protection suitable for splash risks, for example goggles or a visor, is worn if there is any danger of splashing.
- Rubber gloves are checked for holes, tears, and thin patches, and replaced if faulty.
The type of glove material and respiratory protection against dust are read from the product’s data sheet and are covered in Chapter 5 · Safety on personal protective equipment.
First aid
First aid follows the label, the product’s data sheet, and the workplace procedure. Guidance from HSE for chemical injuries and from NIOSH, the United States occupational safety and health institute, for hydrogen peroxide:
- Eyes. The eye is flushed with water or sterile fluid for at least 10 minutes with the eyelids held open, then the casualty is sent to hospital. Loose granules are washed out with clean water, and no attempt is made to remove anything embedded in the eye.
- Skin. The affected area is flooded with water for 20 minutes, and flooding can continue on the way to hospital. Contaminated clothing that is not stuck to the skin is removed, and the first aider avoids becoming contaminated as well.
- Swallowed. The casualty is taken at once to a doctor or the emergency services together with the product label.
- Inhaled. The casualty is moved to fresh air at once, kept warm and at rest, and given medical attention as soon as possible. If breathing has stopped, a trained first aider gives artificial respiration and the emergency services are called.
UKHSA records that swallowed hydrogen peroxide decomposes rapidly and releases oxygen gas, which can cause belching, painful distension of the stomach, and foaming at the mouth. What happens next is a decision for medical personnel.
Handling and storage
The safety data sheet for a product of this class gives a storage temperature of 5 to 40 °C and names acid as an incompatible material. That upper limit is easily exceeded next to the dryer room. Storage guidance from the Environment Agency and HSE:
- The powder is stored in a cool, dry place, protected from direct sunlight, in its original container, away from flammable materials and heat sources.
- Oxidizing agents are stored apart from reducing agents and from flammable materials, and acids are kept separate from alkalis, in marked bays.
- Substances that give trouble when wet are stored under cover and off the floor, with container lids always kept on.
A bucket is opened only while measuring and is closed again at once. The scoop is dry and is used for this product alone. A small spill of dry powder is handled according to Chapter 6 · Safety on chemicals in technician work, with clean, dry tools, and is not thrown away with flammable trash. Leftover product and empty containers are handled according to the label and Chapter 35 · Water & Water Treatment on B3 waste in hotels, laundries, and workshops.
Worked example
Figures in the examples below are practice figures, unless their origin is stated. Ingredient contents come from the data sheet and are read as percent by mass. The molar mass of sodium carbonate is 106.0 g/mol and of hydrogen peroxide 34.0 g/mol, and the molar volume of a gas is 24.5 L/mol at 25 °C and 1 atm. The results are used to understand magnitudes, not for dosing.
Example 1: the fraction of hydrogen peroxide in sodium percarbonate. Two moles of sodium carbonate have a mass of g and three moles of hydrogen peroxide g, so the total is g. The hydrogen peroxide fraction is or 32.5 percent, and the sodium carbonate fraction is or 67.5 percent. Two thirds of the mass of percarbonate is sodium carbonate, so this product is more alkaline than its free sodium carbonate content suggests.
Example 2: hydrogen peroxide per kilogram and per bucket. One kilogram of powder with 30 percent percarbonate contains g of hydrogen peroxide, and at 60 percent g. A 20 kg bucket contains g to g, that is, about 2 to 4 kg of hydrogen peroxide in bound form.
Example 3: oxygen gas when the peroxide decomposes. From 97.5 g of hydrogen peroxide, the oxygen is mol or L. From 195 g, the oxygen is mol or L. A small part of that volume is already enough to make a tightly sealed bucket bulge.
Example 4: estimated pH of a 1 percent solution. A 1 percent solution means 10 g of powder per liter. If free sodium carbonate and percarbonate are each 30 percent, the free sodium carbonate is g and the sodium carbonate from the percarbonate is g. The total is 5.025 g or mol/L. With , this gives mol/L, so pH . That result is at the upper end of the range of 11.1 to 11.5 on the data sheet.
Example 5: paste on a wet scoop and the eye classification limits. One hundred grams of powder is hit by 50 g of water, and all of its peroxide is assumed to be released into the paste. At 30 percent percarbonate, the hydrogen peroxide is g in g of paste, that is, percent. At 60 percent, g gives percent. The first figure falls in the range for serious eye irritation, 5 to less than 8 percent, and the second falls in the range for serious eye damage, 8 to less than 50 percent. For comparison, one liter of a 1 percent solution contains only g of hydrogen peroxide, about 0.2 percent.
Example 6: carbon dioxide gas on contact with acid. One kilogram of powder with 30 percent free sodium carbonate and 30 percent percarbonate contains g of sodium carbonate, that is, mol. Each mole of carbonate that reacts completely with acid releases one mole of carbon dioxide, so the gas is at most L. If this powder is tipped into a bucket holding acid neutralizer, the mixture foams and overflows. This calculation is an upper limit and not a direction to mix.
Stop conditions
- The powder or its paste gets into the eyes, or onto the skin: stop work and rinse at once with water. The casualty is taken to a doctor or the emergency services.
- Someone swallows the powder or its solution, or is short of breath after inhaling dust: call the emergency services and take the product label along.
- A bucket or sack is bulging, feels warm, hisses, or smokes: do not open it and do not move it. Clear the area around it; the supervisor calls trained personnel or the building emergency response team.
- The powder is caked, discolored, or wet: do not break it up by hand and do not use it. The laundry supervisor asks the supplier how to deal with it.
- The powder is tipped into an acid product, into chlorine bleach, or into a container whose previous contents are not known: keep away from the container and clear the area. The supervisor calls trained personnel or the emergency response team.
- Eye protection or gloves are not available or are damaged, there is no dry scoop, or there is no eye-rinsing facility near the place where the powder is measured: do not measure out the powder. The supervisor provides the equipment first.
- A powder spill is larger than the local spill kit can handle, or is mixed with fabric, cardboard, oil, or water: clear the area and hand over to trained personnel or the emergency response team.
- There is a fire or a smell of burning in the store where this powder is kept: leave the store and sound the alarm. The fire department is told that there is an oxidizing agent in the store.
- The label is missing, the safety data sheet is absent or past its validity date, or the dosing rate is not written on the label or in the procedure: do not measure by guesswork. The supervisor asks the supplier for written information.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
Oxygen bleach is safe because it only releases oxygen and soda.
Why is it wrong?
Its written classification is skin corrosion category 1B and serious eye damage category 1. Its solution has a pH of about 11, and wet powder contains hydrogen peroxide at a concentration from a few percent to more than ten percent.
Common misconception
Dry powder does not change until it goes into the machine.
Why is it wrong?
Water vapor from the air and a wet scoop are enough to start decomposition. The signs are lumps and a bulging container.
Common misconception
The more bubbles, the stronger the bleaching.
Why is it wrong?
The bubbles are oxygen gas from peroxide that has already decomposed, that is, the part that is lost. What bleaches is the peroxide still intact in the solution.
Common misconception
Oxygen bleach can be mixed with chlorine bleach or neutralizer so that the job is complete.
Why is it wrong?
Two different bleaches react with each other, and acid uses up its carbonate while releasing gas. Each product enters the machine through its own line and its own stage.
Links to other chapters
Chapter 8 · Laundry on oxidizers and finishing agents explains how peroxide bleaches, and Chapter 26 on reading the safety data sheets of cleaning products gives the way of checking the data sheet on which this chapter is based. Chapter 25 on chemical reactivity and incompatibility contains the segregation of oxidizing agents from other materials, and Chapter 53 on chlorine bleach for laundry covers the other class of bleach, which must not meet this product.
Exercises and worked solutions
The figures in the problems are for practice. The fraction of hydrogen peroxide in sodium percarbonate is taken as 0.325 and the fraction of sodium carbonate as 0.675.
Try to answer first, then open the worked solution.
A quantity of 500 g of powder with 40 percent sodium percarbonate is measured out for one load. How many grams of hydrogen peroxide does it carry?
Check my answer
See the worked solution
The sodium percarbonate is g, so the hydrogen peroxide is g. That amount cannot be seen from outside, because the powder has no odor.
A bucket holding 10 kg of powder with 30 percent percarbonate becomes damp, and half of its hydrogen peroxide decomposes. How many liters of oxygen gas are released, and what follows if the bucket is tightly sealed?
Check my answer
See the worked solution
The hydrogen peroxide at the start is g, and the part that decomposes is g. The oxygen gas is mol or L. A tightly sealed bucket cannot hold that much gas, so its lid bulges or comes off; a bucket like that is not opened by the operator and is reported to the supervisor.
An operator washes the scoop, uses it straight away to take powder, then returns the rest of the measured powder to the bucket. What are the two mistakes?
Check my answer
See the worked solution
A wet scoop carries water into the powder, and water starts the release and decomposition of the peroxide, so the powder cakes. Measured powder that is returned can carry water and dirt into the bucket, so product that has been taken out is not returned to its container.
A 0.5 percent solution is made from powder in which free sodium carbonate and percarbonate are each 30 percent. Estimate its pH.
Check my answer
See the worked solution
In 5 g of powder per liter there are g of free sodium carbonate and g from the percarbonate, a total of 2.5125 g or mol/L. Then mol/L and pH . A solution twice as dilute still has a pH above 11.
In the store, a bucket of oxygen bleach is kept on a shelf above jerry cans of acid neutralizer, next to a stack of cardboard and oily rags, near a steam pipe. What has to change, and who decides?
Check my answer
See the worked solution
The bucket is moved from above the acid jerry cans because a spill of either one would meet the other, kept away from the cardboard and oily rags because an oxidizing agent contributes to combustion, and kept away from the steam pipe because heat speeds up decomposition. The new storage place is decided by the laundry supervisor together with the building technician.
A lump of wet powder splashes into an operator’s eye. The stinging feels mild, and the operator intends to carry on working. What is wrong?
Check my answer
See the worked solution
The paste of this powder contains hydrogen peroxide at a concentration from a few percent to more than ten percent and is strongly alkaline, so mild stinging is no measure. The eye is flushed with water for at least 10 minutes with the eyelids held open, then the operator is sent to hospital.
References
External sources
- Safer Chemical Ingredients Listepa.gov
- Benefits and Potential Risks of the Lactoperoxidase system of Raw Milk Preservation: Report of an FAO/WHO technical meetingiris.who.int
- Development of Operational and Policy Guidance on the Use of Hydrogen Peroxideassets.publishing.service.gov.uk
- Hydrogen peroxide: incident managementassets.publishing.service.gov.uk
- Chemistry 2eopenstax.org
- Chemicals - safe use and handlinghse.gov.uk
- Safe use of cleaning substances in the hospitality industryhse.gov.uk
- Basic advice on first aid at workhse.gov.uk
- First Aid Procedures for Chemical Hazardscdc.gov
Revision history
| Date | Version | Change |
|---|---|---|
| November 15, 2026 | 1 | First published |
How to cite
Kurnia (2026). Powdered oxygen bleach for laundry: sodium percarbonate and sodium carbonate, release of hydrogen peroxide, solution pH, oxidizing properties and moisture, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/pemutih-oksigen-serbuk-untuk-laundry-natrium-perkarbonat-dan-natrium-karbonat-pelepasan-hidrogen-peroksida-ph-larutan-sifat-pengoksidasi-dan-kelembapan-serta-penanganan-dan-penyimpanan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.
A quantity of 500 g of powder with 40 percent sodium percarbonate is measured out for one load. How many grams of hydrogen peroxide does it carry?
A bucket holding 10 kg of powder with 30 percent percarbonate becomes damp, and half of its hydrogen peroxide decomposes. How many liters of oxygen gas are released, and what follows if the bucket is tightly sealed?
An operator washes the scoop, uses it straight away to take powder, then returns the rest of the measured powder to the bucket. What are the two mistakes?
Nearby chapters
Reading order by shelf: Chemistry · Chapter 53.
Reading order by shelf: Chemistry · Chapter 51.