By Kurnia · Published November 15, 2026 · Version 1 · 21 min read
Acid laundry softener
ester quaternary ammonium salt with formic acid at 10 to 30 percent or glycolic acid, pH 3 to 4 and pH 6 to 8, skin corrosion, the ban on mixing with chlorine bleach, and handling and storage
In two hospitals, bleach that met an acid cleaner at 4 percent released chlorine gas until wards were evacuated. Acid laundry softener carries a far more concentrated acid. This chapter covers acid laundry softener from the side of its chemistry according to the manufacturer’s safety data sheets for two products of this class: an ester quaternary ammonium salt as the softening ingredient, formic acid at 10 to 30 percent with pH 3 to 4 in the first product, glycolic acid with pH 6 to 8 in the second product, the skin corrosion class, why a weak acid still injures, the ban on mixing with chlorine bleach, vapor and the limit values in air, personal protective equipment, first aid, and handling and storage. Dispenser settings and wash programs are not given. Mixtures that are already giving off gas, large spills, and treating a casualty are stated as work for other parties.
This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.
Between October 1987 and November 1989, chlorine gas was released five times at two state hospitals in California, United States, and at least 14 people were affected. Each incident began with the same thing: patients helping with cleaning duties brought bleach, which is a sodium hypochlorite solution, together with a cleaner based on phosphoric acid. At the first hospital, the acid content of that cleaner was only 4 percent. In one of the incidents, the room’s exhaust fan was out of order and the windows were sealed shut, so the gas spread throughout the ward and one patient had an asthma attack. The label of that cleaner did not name its active ingredient and did not warn of the danger of mixing it with other materials.
A laundry chemical room holds a pair of materials of the same kind. One jerry can contains chlorine bleach. Another jerry can contains acid softener, which according to the manufacturer’s safety data sheet for one product of this class contains formic acid at 10 to 30 percent. The name softener gives the impression of the friendliest product in that room, whereas what it contains is an acid several times more concentrated than the cleaner at those hospitals (Example 5). Operators need to know what is in that jerry can, what it does to skin and eyes, and which materials must not meet it.
Scope
This chapter covers one class of product, namely liquid laundry softener that is acidic or contains an acid: its softening ingredient, its acid, its pH and hazard class, the materials it must not meet, vapor, personal protective equipment, first aid, and handling and storage. The product data come from the manufacturer’s safety data sheets for two products of this class. Other products may differ, so what applies is the label and the safety data sheet of the product in use.
This chapter is study material, not a work instruction. The stage at which the softener enters, dispenser settings, and wash programs are not given; all of them are set by the chemical supplier. How cationic softeners act on fibers and the limits on their use are in Chapter 8 · Laundry on oxidizers and finishing agents, the final rinse pH is in Chapter 9 · Laundry on pH and chemical measurement throughout the cycle, programs and doses are in Chapter 11 · Laundry on wash program architecture and Chapter 12 · Laundry on sorting, program design, and dose scaling, and dispensers are in Chapter 1 · Chemical Dispensing on peristaltic dispensers and Chapter 2 · Chemical Dispensing and Chapter 3 · Chemical Dispensing on laundry dispensers.
How to check a data sheet is in Chapter 26 on reading the safety data sheets of cleaning products, labels and spills are in Chapter 6 · Safety on chemicals in technician work, chemical burns are in Chapter 41 · Biology & Microbiology on the skin and chemicals, and the choice of protection is in Chapter 5 · Safety on personal protective equipment. The two products that most need to be kept away from acid softener are covered in Chapter 53 on chlorine bleach for laundry and Chapter 54 on laundry neutralizers based on sodium metabisulfite.
Work outside the authority of laundry operators and building technicians: setting the dose and repairing the dispenser, handling mixtures that are already giving off gas or large spills, and giving treatment other than first aid. The dose and the dispenser belong to the chemical supplier or the dispenser technician, gas incidents and large spills belong to trained personnel or the emergency response team, and casualties are handled by a doctor or the emergency services.
What the two products contain according to the data sheets
The manufacturer’s safety data sheets for two products of this class contain the following data.
| Data sheet entry | First product | Second product |
|---|---|---|
| Written use | laundry softener | laundry product for industrial and professional use |
| Quaternary ammonium salt, CAS number 157905-74-3 | 10 to 30 percent | 5 to 10 percent |
| Acid | formic acid, CAS number 64-18-6, 10 to 30 percent | glycolic acid, CAS number 79-14-1, 1 to 5 percent |
| Isopropanol, CAS number 67-63-0 | 1 to 5 percent | 1 to 5 percent |
| Form and pH of the 100 percent product | liquid; pH 3 to 4 | liquid; pH 6.0 to 8.0 |
| Relative density | 0.995 to 1.005 | 1.0000 to 1.0060 |
| Written classification | skin corrosion category 1A; serious eye damage category 1 | skin corrosion category 1A; serious eye damage category 1 |
| Written dosing | dilution of 0.1 to 0.3 percent | automatic setting through a dispenser |
| Storage temperature | 10 to 40 °C | 0 to 45 °C |
| Materials to keep away | bases | strong bases; bleach and other chlorinated products |
| Issued and valid until | February 20, 2024; February 19, 2029 | June 30, 2025; June 29, 2030 |
The two products contain the same salt and differ in their acid. The other ingredients in the two jerry cans are not listed and cannot be known from the data sheets.
The ester quaternary ammonium salt: the softening ingredient
A quaternary ammonium salt is a compound whose nitrogen atom is bonded to four groups and therefore carries a positive charge. The data sheets name the ingredient methyl bis(ethyl alkyl)-2-hydroxyethyl ammonium methyl sulfate. The list of safer chemical ingredients kept by the United States Environmental Protection Agency (EPA) records the same CAS number as esters of fatty acids with a quaternary ammonium compound, in the form of methyl sulfate salts, and places it in the surfactants functional class.
The word ester means that its fatty acid chains are attached through ester bonds, the same kind of bond that makes up fats. How that positively charged salt attaches to fibers, why softener enters only at the final rinse, and why softener reduces the absorbency of towels are explained in Chapter 8 · Laundry.
In that EPA list, this ingredient is marked with a green circle, meaning a chemical that has been verified to be of low concern based on experimental and modeled data. That mark rates one ingredient, not a finished product; the hazard class of a product is read from the product’s own data sheet.
Formic acid: a weak acid that is still corrosive
Formic acid, with the formula HCOOH, is a colorless liquid with a pungent, penetrating odor that mixes with water in all proportions and is corrosive to metals. Its molar mass is 46.0 g/mol. A weak acid is an acid of which only a small fraction of the molecules break up into ions when it dissolves in water. Formic acid belongs to that group, with the ionization constant .
For a solution of the weak acid alone, the hydronium ion concentration and the pH can be estimated with:
where is the acid concentration in mol/L. This approximation holds when the fraction that ionizes is much smaller than , and it treats the solution as ideal. When the acid is present together with its salt, the pH follows the Henderson-Hasselbalch equation:
where and both concentrations are in mol/L. The calculation for formic acid alone gives a pH below 2 across the whole concentration range of the first product, lower than the written pH of 3 to 4 (Example 2). That written figure fits a solution in which part of the acid is present as formate ions (Example 3). In both situations the amount of acid remains large: pH measures only the hydronium ions that are free at that moment, not the acid reserve that is ready to ionize as soon as those ions are used up.
For that reason “weak” does not mean it does not injure. The UK Health Security Agency (UKHSA) quotes an assessment that formic acid above 10 percent is strongly corrosive to skin. On skin, this acid may cause pain, blistering, ulceration, and tissue death; in the eyes, pain, watering, sensitivity to light, and corneal burns. Its vapor irritates the eyes and nose and causes sore throat, cough, and chest tightness. If swallowed, this acid immediately burns the mouth, throat, and stomach.
In the Great Britain classification and labeling regulation quoted by UKHSA, formic acid at 90 percent or more falls in skin corrosion category 1A, at 10 to less than 90 percent in category 1B, and at 2 to less than 10 percent it irritates skin and eyes. The content of 10 to 30 percent in the first product lies within the corrosive range. Its data sheet writes category 1A, one step more severe than that Great Britain limit; both mean severe skin burns and eye damage, and the handling is the same.
The second product: pH 6 to 8 with a skin corrosion class
The second product contains glycolic acid at 1 to 5 percent, and the pH of the 100 percent product is written as 6.0 to 8.0, which is around neutral. Its written classification is nevertheless skin corrosion category 1A and serious eye damage category 1. That data sheet does not explain why a product with a pH around neutral is given a corrosive class.
Users do not decide for themselves which is right. Chapter 26 gives the way to check the agreement between pH, classification, and personal protective equipment on a data sheet, and the question is put to the supplier. Until there is an answer, the product is handled according to its written class, because the more severe class demands more complete protection.
The ban on mixing with chlorine bleach
The editorial note of the report on those hospital incidents sets out the chemistry: when sodium hypochlorite and an acid are mixed, chlorine gas and water are released. The chlorine gas then reacts with water to form hydrochloric acid and hypochlorous acid. Phosphoric acid at 4 percent was already enough to evacuate a ward, and acid softener carries a more concentrated acid.
The data sheet for the second product writes that ban clearly: do not mix with bleach or other chlorinated products, because it will cause chlorine gas. For the first product, whose acid content is far higher, the same ban applies on the basis of the reaction above. HSE, the British occupational safety authority, writes that products containing bleach mixed with acidic cleaners or ammonia give off harmful gases, and gives workers one short rule: never mix cleaning substances.
In the laundry, softener and chlorine bleach are not poured into the same container, are not measured with the same measuring jug, are not stored on the same tray, and their dispenser tubes are not swapped. Both do enter the same machine, but at different stages and after being diluted by water; that sequence is set by the supplier. What is dangerous is two concentrated products meeting outside the machine.
Formic acid also reacts violently with oxidizers and strong bases, and attacks many metals and plastics. Both data sheets ask for the product to be kept away from bases. Alkali builders, which are covered in Chapter 49 on laundry alkali builders, are stored and measured separately, and the softener stays in its original container.
Vapor, limit values in air, and personal protective equipment
NIOSH, the United States occupational safety and health institute, records the exposure routes of formic acid as inhalation, ingestion, and skin and eye contact, with the symptoms irritation of the eyes, skin, and throat, skin burns, dermatitis, watering eyes, cough, breathing difficulty, and nausea. Its recommendations: skin and eye contact is prevented, contaminated skin is washed immediately, work clothing that is wet or contaminated is removed, and an eyewash and a quick-drench facility are provided.
Permitted short-term exposure (Indonesian pajanan singkat diperkenankan, PSD) is the concentration of a chemical in workplace air that must not be exceeded so that workers exposed for no more than 15 minutes can still tolerate it, and such exposure must not occur more than 4 times in one working day. The annex to Permenaker 5/2018 (Minister of Manpower Regulation) lists formic acid with an 8-hour threshold limit value of 5 parts per million (ppm), and the figure 10 ppm or 19 mg/m³ in the short-term exposure or ceiling column, with the remark irritation of the upper respiratory tract, eyes, and skin. As of November 2026 that regulation has the status in force on JDIH Kemnaker. According to UKHSA, people with asthma and other breathing problems may be more sensitive to formic acid vapor.
The HSE guidance for cleaning substances in hospitality:
- The protective clothing provided is always worn when handling substances, especially concentrates, and eye protection such as goggles or a visor is worn if there is any danger of splashing.
- Rubber gloves are checked for holes, tears, and thin patches, and replaced if faulty.
- Substances are used only in well-ventilated areas, and mechanical ventilation is checked to be switched on and working.
- Where tap water is not available for eye irrigation, at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers is provided.
The glove material and the respiratory protection are read from the data sheet of the product in use and chosen according to Chapter 5 · Safety.
First aid
First aid follows the workplace procedure. For formic acid NIOSH specifies immediate eye irrigation, immediate flushing of the skin with water, respiratory support, and immediate medical attention if swallowed. The UKHSA and NIOSH guidance:
- Eyes. Contact lenses are removed, the eye is irrigated with lukewarm water for at least 10 to 15 minutes, then the casualty seeks medical advice.
- Skin. Soiled clothing is removed without pulling it over the head, the affected area is washed with lukewarm water and soap for at least 10 to 15 minutes, then the casualty seeks medical advice.
- Swallowed. The casualty gets medical attention immediately.
- Inhaled. The casualty is moved to fresh air at once, kept warm and at rest, and gets medical attention as soon as possible. If breathing has stopped, a trained first aider gives artificial respiration and the emergency services are called.
The UKHSA guidance for healthcare professionals prohibits giving neutralizing chemicals to a casualty who has swallowed this acid, because the heat of the neutralization reaction may increase the injury. A person exposed to chlorine gas from a mixture with bleach goes out to fresh air and is examined by a doctor; the symptoms and handling of chlorine gas are in Chapter 41 on concentrated sodium hypochlorite and chlorinated sanitizing powder in the kitchen. The product label or data sheet is taken to the doctor.
Handling and storage
The storage temperature according to the data sheets is 10 to 40 °C for the first product and 0 to 45 °C for the second product. A 20 L jerry can of the first product has a mass of about 20 kg, so moving it follows Chapter 9 · Safety on lifting and moving loads with equipment.
HSE gives guidance on storing and handling cleaning substances in hospitality:
- Substances are kept in their original labeled containers, with lids, and securely stored, away from heat, sunlight, foodstuffs, and members of the public, especially children.
- The manufacturer’s storage instructions are checked because some products need to be stored separately from others.
- Pouring from bulk containers is avoided, and handling is minimized by using siphons or pumps. Cleaning substances are never transferred into food or drink containers.
- When a concentrate is diluted, the concentrate is added to the water, not the water to the concentrate.
- Spills on floors or work surfaces are cleaned up immediately, and the workplace has a spill procedure.
A dispenser carries out that advice to minimize handling, so people meet the concentrated product only when the jerry can is changed, when tubing or a pump leaks, and when there is a spill. The suction tube moves straight from the old jerry can to the new one, and the softener drip tray is not shared with other products. Small spills are handled according to Chapter 6 · Safety.
Worked example
The figures in the examples below are practice figures, unless their origin is stated. The relative density of the first product is taken as 1.000, the midpoint of the range on the data sheet, so one liter of product has a mass of 1,000 g.
Example 1: formic acid per liter and per jerry can. At 10 percent, one liter of the first product contains g of formic acid, and at 30 percent g. A 20 L jerry can contains g to g, that is 2.0 to 6.0 kg of formic acid. In molar units, the concentration is mol/L to mol/L.
Example 2: the pH if it contained formic acid alone. At 2.17 mol/L, the hydronium ion concentration is mol/L, so pH . At 6.52 mol/L, the hydronium ion concentration is mol/L, so pH . The fraction ionized is , less than 1 percent, so the approximation is valid. The pH of 3 to 4 on the data sheet lies to units above this calculation.
Example 3: pH 3 to 4 and the acid reserve. For formic acid, . At pH 3, the ratio of formate ions to formic acid is ; at pH 4, . The fraction that is still formic acid is at pH 3 and at pH 4. A solution with a pH of 3 to 4 still holds 36 to 85 percent of its acid in the form that has not ionized.
Example 4: a use solution of 0.1 to 0.3 percent. A dilution of 0.1 percent means 1 g of product in 1,000 g of solution, and 0.3 percent means 3 g. The formic acid in it is at least g and at most g, that is 0.010 to 0.090 percent of the solution. That highest concentration is times below the 2 percent limit for irritation. Rinse water with softener is far below that range, whereas the contents of the jerry can lie within the corrosive range.
Example 5: compared with the cleaner in the hospital incidents. That cleaner contained 4 percent phosphoric acid. Assuming one liter of it has a mass of 1,000 g, it contains g of phosphoric acid, and with a molar mass of 98.0 g/mol its concentration is mol/L. The formic acid concentration of the first product is to times that figure. Phosphoric acid can release more than one hydrogen ion per molecule, so this comparison is rough. The direction is still clear: acid softener carries several times more acid than a cleaner that was already enough to release chlorine gas in a ward.
Example 6: formic acid vapor and the threshold limit value. NIOSH gives the equivalence of 1 ppm of formic acid as 1.88 mg/m³, so 5 ppm equals mg/m³ and 10 ppm equals mg/m³, which is rounded to 19 mg/m³ in the annex to the regulation. A chemical room measuring 4 m by 3 m by 3 m has a volume of m³, so 5 ppm is matched by mg of formic acid vapor. That amount is contained in mg of product at 30 percent, slightly more than one gram. This calculation assumes that all the formic acid evaporates and is mixed evenly without ventilation, so the result is an upper limit.
Stop conditions
- A sharp smell of chlorine is noticed, or someone is coughing, short of breath, or has stinging eyes near the jerry can, tray, or dispenser: stop work and everyone goes out to fresh air. The supervisor calls trained personnel or the building’s emergency response team, and anyone with symptoms is examined by a doctor.
- Softener meets chlorine bleach in a container, tray, measuring jug, or tube: keep away from that place, do not stir it, do not flush it, and clear the area. Trained personnel or the emergency response team deal with it.
- Concentrated product gets in the eyes or on the skin: stop work and rinse immediately with water. The casualty is taken to a doctor or the emergency services.
- A person swallows the product, or is short of breath after inhaling vapor or gas: call the emergency services. Do not give baking soda or any other neutralizing substance.
- Eye protection or gloves are not available or are damaged, or there is no eyewash facility near the workplace: do not change the jerry can and do not measure out product. The supervisor provides the equipment first.
- A jerry can without a label, a label that does not match the marking on the tube, unmarked dispenser tubing, or a safety data sheet that is missing or past its validity date: do not connect that jerry can. The supervisor asks the supplier for an explanation.
- The dispenser tubing, pump, or connections are dripping, or the drip tray contains an unidentified liquid: keep people away and do not dismantle the dispenser. The dispenser technician or the supplier repairs it.
- Softener meets a concentrated base product, or the container feels hot, hisses, or foams: keep away from the container and clear the area. The supervisor calls trained personnel or the emergency response team.
- A spill larger than the local spill kit can handle, or one flowing toward another product or a drain: clear the area and hand over to trained personnel or the emergency response team.
- The softener runs out much faster or much more slowly than usual, or linen comes out stained or smelling of acid: the operator does not change the dispenser setting or the program. The chemical supplier or the dispenser technician checks it.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
Softener is the gentlest product in the chemical room.
Why is it wrong?
The data sheets for both products write skin corrosion category 1A and serious eye damage category 1. The first product contains formic acid at 10 to 30 percent.
Common misconception
A weak acid does not injure.
Why is it wrong?
Weak means that only a small fraction of its molecules are ionized at any one moment. Formic acid above 10 percent is assessed as strongly corrosive to skin.
Common misconception
pH 3 to 4 is mild, and pH 6 to 8 means safe.
Why is it wrong?
pH does not measure the acid reserve, and even a product with a pH around neutral can be given a corrosive class on its data sheet. What counts is the written class and the label.
Common misconception
Bleach and softener both go into the machine, so they may meet.
Why is it wrong?
In the machine the two enter at different stages and are already diluted. In the concentrated state, acid and chlorine bleach release chlorine gas.
Common misconception
If acid gets on you, neutralize it with soda.
Why is it wrong?
The existing guidance uses water in large amounts and for a long time. The neutralization reaction gives off heat and may increase the injury.
Links to other chapters
Chapter 8 · Laundry on oxidizers and finishing agents explains cationic softeners, neutralizers, and hazardous mixtures in the laundry. Chapter 25 on chemical reactivity and incompatibility contains the segregation of acids from oxidizers and bases, and the heat of neutralization is calculated in Chapter 12 on thermochemistry.
Exercises and worked solutions
The figures in the problems are used for practice.
Try to answer first, then open the worked solution.
A 25 L jerry can contains the first product with a relative density of 1.000. How many kilograms of formic acid, quaternary ammonium salt, and isopropanol are in it according to the concentration ranges on the data sheet?
Check my answer
See the worked solution
The mass of product is kg. The formic acid is kg to kg, and the quaternary ammonium salt is the same amount because its concentration range is the same. The isopropanol is kg to kg.
A 20 L jerry can contains the second product with a relative density of 1.003. How many kilograms of glycolic acid and quaternary ammonium salt are in it?
Check my answer
See the worked solution
The mass of product is kg. The glycolic acid is kg to kg, and the quaternary ammonium salt is kg to kg. The acid content of the second product is far smaller, but its written class is the same.
The first product with 20 percent formic acid is diluted to a use solution of 0.2 percent. What is the formic acid concentration of that solution in percent, and how many times below the 2 percent limit is it?
Check my answer
See the worked solution
A 0.2 percent solution contains 2 g of product in 1,000 g of solution, so the formic acid is g or 0.040 percent. That figure is times below the 2 percent limit. The corrosive hazard lies in the concentrated product in the jerry can and the tubing, not in the rinse water.
The softener tube and the chlorine bleach tube on a dispenser drip into the same tray, and there is already a pool in that tray. What is the danger, and who deals with it?
Check my answer
See the worked solution
In that tray two concentrated products meet, and acid with sodium hypochlorite releases chlorine gas. People move away and the area is cleared; the tray is not lifted, stirred, or flushed. Trained personnel or the emergency response team deal with the contents of the tray, and the dispenser technician or the supplier repairs the leak and separates the trays.
An operator is splashed with the first product on the arm. They say that pH 3 to 4 is “like vinegar” and intend to rinse it off later. What is wrong?
Check my answer
See the worked solution
That product contains formic acid at 10 to 30 percent with a skin corrosion class, and pH does not measure its acid reserve. Delaying the rinse gives the acid time to damage the skin. The arm is rinsed at once, wet clothing is removed, and the incident is reported and checked by a doctor.
A storeroom worker puts a jerry can of the second product on the chlorine bleach shelf and measures it out without eye protection, on the grounds that its pH is 6 to 8. What is wrong?
Check my answer
See the worked solution
The data sheet for that product writes skin corrosion category 1A and serious eye damage category 1, and prohibits mixing with bleach and other chlorinated products. The written pH does not cancel that class and that ban. The jerry can is moved to a storage place separate from chlorine bleach, eye protection is worn, and the supervisor asks the supplier about the mismatch between the pH and the class.
References
External sources
- NIOSH Pocket Guide to Chemical Hazards - Formic acidcdc.gov
- First Aid Procedures for Chemical Hazardscdc.gov
- Formic acid: incident managementassets.publishing.service.gov.uk
- Formic acid: general informationgov.uk
- Safer Chemical Ingredients Listepa.gov
- Epidemiologic Notes and Reports Chlorine Gas Toxicity from Mixture of Bleach with Other Cleaning Products -- Californiacdc.gov
- Chemistry 2eopenstax.org
- Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
- Safe use of cleaning substances in the hospitality industryhse.gov.uk
Revision history
| Date | Version | Change |
|---|---|---|
| November 15, 2026 | 1 | First published |
How to cite
Kurnia (2026). Acid laundry softener: ester quaternary ammonium salt with formic acid at 10 to 30 percent or glycolic acid, pH 3 to 4 and pH 6 to 8, skin corrosion, the ban on mixing with chlorine bleach, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/pelembut-laundry-asam-garam-amonium-kuaterner-ester-dengan-asam-format-10-sampai-30-persen-atau-asam-glikolat-ph-3-sampai-4-dan-ph-6-sampai-8-korosi-kulit-larangan-mencampur-dengan-pemutih-klor-serta-penanganan-dan-penyimpanan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.
A 25 L jerry can contains the first product with a relative density of 1.000. How many kilograms of formic acid, quaternary ammonium salt, and isopropanol are in it according to the concentration ranges on the data sheet?
A 20 L jerry can contains the second product with a relative density of 1.003. How many kilograms of glycolic acid and quaternary ammonium salt are in it?
The first product with 20 percent formic acid is diluted to a use solution of 0.2 percent. What is the formic acid concentration of that solution in percent, and how many times below the 2 percent limit is it?
Nearby chapters
Reading order by shelf: Biology & Microbiology · Chapter 1.
Reading order by shelf: Chemistry · Chapter 54.