By Kurnia · Published November 15, 2026 · Version 1 · 20 min read
Daily floor cleaners
a ready-to-use neutral product and a product with sulfate surfactants, pH 7 to 9, mopping method and changing the solution, slippery floors and residue, and handling and storage
An occupational therapist in a British hospital slipped on a vinyl floor that had just been mopped and not dried, and later lost a leg after dozens of operations. This chapter covers daily floor cleaners from the side of the product and how it is used: two ready-to-use products according to the manufacturer’s safety data sheets, one with a pH of 7.0 to 7.5 and no ingredient list and one with a pH of 8 to 9 and two sulfate surfactants, what those pH figures mean, how sulfate surfactants lift soil, mopping with two buckets, when the solution and the mop head are changed, why a freshly mopped floor is slippery, the residue left after the water dries, wet work and the skin, and handling and storage. No dilution rate is given because the data sheets contain none. Floor repairs, spills of blood and body fluids, and medical treatment are stated as work for other parties.
In 1992, an occupational therapist in a large hospital in Britain slipped on a wet vinyl floor. Someone had just mopped that floor, and then did not dry it, did not put out barriers, and did not put out warning signs. The therapist fell onto the right ankle. Six years earlier the therapist’s knee had already been injured in a slip on the steps of the same hospital. Over the following years the therapist had 30 operations, the foot was amputated, and at the 32nd operation the leg was amputated at the knee. HSE, the British occupational safety authority, presents that story as an example of accidents that are easily avoided.
That floor was simply wet after mopping. According to the manufacturer’s safety data sheets for two products of this class, a daily floor cleaner has a pH of 7.0 to 7.5 or 8 to 9, and both are sold ready to use. Its greatest hazard comes from how the floor is mopped and left. For that reason this chapter covers the contents of the product only as far as needed, and then the mopping method, when the solution is changed, why a freshly mopped floor is slippery, and what is left behind after the water dries.
Scope
This chapter covers liquid floor cleaners with a pH of 7 to 9 for daily mopping of hard floors: contents and pH, sulfate surfactants, the mopping method, changing the solution, slippery floors and residue, skin and eyes, and handling and storage. The product data come from the manufacturer’s safety data sheets for two products, and apply to those products alone. What applies in the workplace is the label and the safety data sheet of the product in use.
This chapter is study material, not a work instruction. Both data sheets describe the product as ready to use and contain no dilution rate, so this chapter gives no dilution rate. Whether the product is diluted, how it is used, and whether a rinse is needed are read from the product label and the workplace procedure. Cleaning power and germ-killing power are not assessed, and floor disinfection is not covered.
Dilution, anionic and nonionic surfactants, and testing in an inconspicuous place are in Chapter 27 on neutral all-purpose cleaners. Greasy kitchen floors are in Chapter 36 on strong alkaline kitchen floor cleaners, and the periodic work of lifting the protective coating is in Chapter 44 on floor finish strippers. Types of floor covering and slip testing are in Chapter 39 · Buildings & Facilities on floors and tiles, micelles and foam are in Chapter 21 on surfactants, colloids, and emulsions, disinfectants are in Chapter 4 · Biology & Microbiology on disinfectants and how they work, and how to check a data sheet is in Chapter 26 on reading safety data sheets for cleaning products.
Some work is outside the authority of cleaning staff. Loose tiles and a floor that stays slippery although it is clean and dry are assessed and repaired by the party appointed by the building manager. Spills of blood and body fluids are handled according to the workplace infection control procedure. Complaints of the eyes, skin, or breathing are handled by a doctor or the emergency services. Cleaning staff mop, change the solution, close the area, and report.
What the two products contain: no ingredient list and two sulfate surfactants
The manufacturer’s safety data sheets for two products of this class give the following picture.
| Item | First product | Second product |
|---|---|---|
| Recommended use | floor cleaner | cleaner |
| Dilution information | sold ready to use | sold ready to use |
| Ingredients listed | none | two sulfate surfactants |
| pH of the 100 percent product | 7.0 to 7.5 | 8 to 9 |
| Relative density | 1.006 to 1.026 | 1.000 to 1.020 |
| Storage temperature | 0 to 50 °C | 0 to 50 °C |
| Issued | October 15, 2024 | February 22, 2024 |
| Valid until | October 14, 2029 | February 21, 2029 |
The two ingredients of the second product are listed as follows.
| Ingredient (name on the data sheet) | CAS number | Concentration (%) |
|---|---|---|
| Sodium polyoxyethylene(2) alkyl (C10 to C16) ether sulfate | 68891-38-3 | 1 to 5 |
| Sodium lauryl sulfate | 151-21-3 | 1 to 3 |
The data sheet of the first product states that the product is not a hazardous substance and lists no ingredient at all. The absence of an ingredient list is not read as proof that the liquid may get in the eyes or be swallowed, as noted in Chapter 27. For the second product, the two listed ingredients add up to 2 to 8 percent and the rest is not itemized (Example 2). Both products are described as ready to use, and there is no dilution figure on their data sheets. Whether the product is poured straight, diluted, or used through a dosing unit is read from the label.
What pH 7 to 9 means
The environmental cleaning guidance for healthcare facilities prepared by the United States CDC together with the Infection Control Africa Network (ICAN) recommends, for most cleaning procedures, neutral detergents with a pH between 6 and 8. The first product sits in the middle of that range. The second product, with a pH of 8 to 9, sits at the upper edge of that range and slightly above it, so that product is slightly basic.
At 25 °C a neutral solution has a pH of 7.00, and pH and pOH add up to 14.00. The hydroxide ion concentration follows
with in mol/L. A difference of one pH unit means that concentration differs tenfold. A solution with a pH of 9 holds a hundred times the hydroxide ions of a neutral solution, but still ten thousand times fewer than the concentrate with a pH of 13 in Chapter 44 (Example 1).
The pH figure on a data sheet is measured on the 100 percent product, that is, what is in the jerry can. The pH of the liquid in the bucket also depends on the water added and the soil carried in by the mop. For surfaces that are sensitive to alkali, what is read is the pH figure on the data sheet, not the word neutral on the packaging, as discussed in Chapter 28 on mildly alkaline all-purpose cleaners.
Sulfate surfactants: the ingredients that lift soil
Synthetic detergents are made of molecules with a nonpolar hydrocarbon chain, for example a twelve-carbon chain, with one ionic group at the end, for example a sulfate or sulfonate group. The nonpolar end is attracted to oil, grease, and dirt particles, while the ionic end is attracted to water. The molecules arrange themselves at the boundary between the soil and the water, so the soil comes away as fine particles that are carried off by the water. Soap forms calcium and magnesium compounds that do not dissolve in hard water, while synthetic detergents form products that dissolve.
A sulfate surfactant is a surfactant whose ionic group is a sulfate group. The United States EPA’s list of safer chemical ingredients lists both CAS numbers in the table above in the surfactants class: CAS number 151-21-3 as sodium lauryl sulfate, that is, the sodium salt of a sulfuric acid ester with a twelve-carbon chain, and CAS number 68891-38-3 as the sodium salt of an alkyl ether sulfate. Both carry the green circle, which marks an ingredient that has been verified to be of low concern.
That mark concerns the ingredient, not the product and not the way of working. HSE writes that detergent is essential if the floor is contaminated with oil or grease, because water alone is not effective in removing it, and that the detergent concentration decides the result: a solution that is too strong can be as ineffective as one that is too weak. Soil that is already held in the water leaves the floor only when the water is lifted with it.
Mopping method: two buckets, pattern, and direction
Wet mopping is not the first step. The preservation guidance of the United States National Park Service (NPS) for ceramic tile floors asks for regular maintenance to begin with vacuuming or dry mopping to remove loose dirt and grit. For small water-based spills, HSE recommends spot cleaning with a paper towel or rag, because that method does not spread the contamination and does not add to the area of wet floor.
HSE also notes the limit of a mop: mopping is usually effective only on fairly smooth floors, because the mop only skims the surface, however much effort is used. The soil needs somewhere to go, for example a separate dirty-water bucket for wringing out the mop.
The two-bucket system is a mopping method for routine cleaning that uses one bucket of cleaning solution and one bucket of rinse water. The CDC and ICAN guidance calls it best practice: the mop is rinsed and wrung out in the rinse-water bucket before it is dipped into the solution again, so the solution stays clean longer and is changed less often. That guidance describes the general process as follows.
- The mop is immersed in the bucket of cleaning solution and wrung out.
- The floor is mopped in a figure-eight pattern with overlapping strokes, and the mop head is turned regularly, for example every 5 to 6 strokes.
- After one small area, for example 3 m by 3 m, the mop is immersed in the rinse-water bucket and wrung out.
- That sequence is repeated from the first step.
The direction of work is from the cleaner part to the dirtier part, and from the farthest point toward the exit, with wet floor signs in place. NIOSH, the United States occupational safety and health institute, notes that a two-step mopping method is better than damp mopping: the solution is applied to one section of the floor with a dripping mop, and after a few minutes it is removed with a wrung mop, before the solution dries.
Changing the solution
The solution in the bucket changes while it is used. Every dip carries soil from the floor into the bucket, and after a while the mop returns part of that soil to the floor (Example 5). The CDC and ICAN guidance asks for mop heads and buckets of solution to be changed as often as needed, for example when visibly soiled, after every isolation room, or every 1 to 2 hours, and at the end of each cleaning session.
The same guidance covers the containers:
- Solutions are prepared according to the manufacturer’s instructions, because a solution that is too dilute or too concentrated reduces the result and adds unnecessary risk.
- A solution container is not topped up over what is left. The container is washed and dried before it is refilled.
- Buckets are cleaned every time the solution is changed and every day, and are then stored upside down so that they dry.
- Mop heads are laundered at least once a day and dried fully before storage. Soiled mop heads are not left soaking in buckets.
The cleaning room has a utility sink or floor drain for disposing of used solution, and mopping equipment is not washed in handwashing sinks. The measures for changing in that guidance are visible soil and time. Foam and fragrance are not among its measures.
Slippery floors and residue
People rarely slip on a clean, dry floor. According to HSE, even a well-wrung mop leaves a thin film of water that is enough to make people slip on a smooth floor. A dry mop afterward shortens the drying time but does not remove the risk, so a smooth floor is left to dry completely before people are allowed through. For healthcare facilities, HSE adds that traditional mopping needs adequate segregation until the floor is dry, and puts residue left from cleaning on its list of causes of slippery surfaces.
HSE ranks the ways of keeping people off a wet floor from the most effective:
- Cleaning during quiet hours.
- Physically closing the area with barriers or locked doors, with directions to an alternative route. The barriers are removed as soon as the floor is dry.
- Cleaning in sections so that there is always a dry path.
- Putting out warning signs. A cone only warns of the hazard, does not prevent people from entering, and is ignored if it is left on a floor that is already dry.
HSE gives an example of a wrong technique at a railway station. A cleaner parked the trolley about 10 meters from a water spill, walked over with a dripping mop, and then mopped the spill out wider. The drips from the mop were just as likely to make someone slip as the spill itself, and a small visible spill turned into a large area of wet, smooth floor. The trolley should have been parked next to the spill, and the spill wiped up with absorbent material until the floor was dry.
What is left after the water evaporates is residue, that is, surfactant and soil that were lifted but not carried away, as explained in Chapter 27. A product used undiluted leaves more residue than a dilute solution (Example 3). For tile floors, NPS asks for the floor always to be rinsed thoroughly after cleaning and for the cleaning solution not to be left to dry on the tiles. Whether a rinse is needed in daily use is read from the label. If the label does not call for one, residue is controlled with a well-wrung mop and a clean rinse-water bucket.
Skin, eyes, and first aid
A pH close to neutral does not remove the risk to the skin. HSE notes that prolonged or frequent contact with water, particularly together with soaps and detergents, can cause dermatitis, and calls such tasks wet work. The steps it recommends are to avoid direct contact where possible, to protect the skin with suitable gloves and moisturizer, particularly at the end of the working day, and to check the hands regularly for the early signs of itchy, dry, or red skin. Mopping throughout a shift counts as wet work, and the mechanism is discussed in Chapter 41 · Biology & Microbiology on the skin and chemicals.
For splashes, HSE asks for the skin or eyes to be washed at once with plenty of water, for medical advice to be sought if the irritation persists, and for the employer to be told. Eye protection is worn if there is any danger of splashing and when cleaning at eye level or above. Where tap water is not available near the workplace, at least one liter of sterile water or sterile 0.9 percent saline in sealed disposable containers is provided for eye irrigation. If the liquid is swallowed or someone is short of breath, a doctor or the emergency services are contacted and the product data sheet is taken along.
Handling and storage
The manufacturer’s safety data sheets for both products of this class give a storage temperature of 0 to 50 °C. HSE gives guidance on storing and handling cleaning substances in the hospitality industry:
- Substances are kept in their original labeled containers. Decanting containers are made of a suitable material, are clean, and are clearly marked with their contents.
- Cleaning substances are never transferred into food or drink containers.
- The storage place is away from heat, sunlight, foodstuffs, and members of the public, especially children, and all containers have lids.
- Solutions are carried in lidded containers, especially if floors are wet or slippery.
Do not mix cleaning substances. HSE writes that products containing bleach, when mixed with acidic toilet cleaners or ammonia, give off harmful gases. Adding a little bleach to the bucket of floor cleaner so that the floor is also freed of germs counts as mixing. Buckets and mops that move from one product to another are rinsed first, and hazardous mixtures are discussed in Chapter 25 on chemical reactivity and incompatibility.
Worked example
The figures in the examples below are practice figures, unless their origin is stated. A relative density of 1.010 is used as the midpoint of the range for the second product on the data sheet, and a layer of liquid 1 mm thick over 1 m² has a volume of 1 liter.
Example 1: what pH 7.5 and pH 9 mean. For pH 7.5, pOH and the hydroxide ion concentration is mol/L. For pH 9, pOH and the concentration is mol/L. Against a neutral solution, pH 9 is units away, that is, times. Against the concentrate with a pH of 13, the distance is units, that is, times lower.
Example 2: listed surfactants in one liter. One liter of the second product has a mass of g. Its two sulfate surfactants add up to percent to percent, that is, g to g. The rest, percent to percent, is not itemized on the data sheet.
Example 3: residue if the product is used undiluted and not rinsed. A mop leaves a layer 0.05 mm thick on a floor of 50 m², that is, liters or g of liquid. The listed surfactants in it are g to g, that is, g per m² to g per m² every time the floor is mopped. That figure shows why the method of use is read from the label and the mop is wrung out.
Example 4: how many times the mop is rinsed. A corridor measures 36 m by 2.5 m, so its area is m². With an area of 3 m by 3 m, that is, m², the mop is rinsed times for that corridor.
Example 5: soil in a single bucket. Suppose the floor carries 2 g of soil per m² and the mop lifts 80 percent of it, that is, g per m². After 90 m², a single bucket holding 8 liters contains g of soil, that is, g per liter. The 0.05 mm layer left by the mop has a volume of 0.05 liters per m² and returns g of soil per m², that is, percent of what was just lifted. With a rinse-water bucket, that soil goes into the rinse water, not into the solution.
Example 6: number of solution changes in one session. A cleaning session lasts 210 minutes. With an interval of 2 hours, the solution is prepared , rounded up to 2 times. With an interval of 1 hour, , rounded up to 4 times. For an 8 liter bucket, the amount needed is liters to liters. If the solution looks soiled sooner, it is changed sooner.
Stop conditions
- A freshly mopped floor cannot be closed to people passing, for example during visiting hours or on a route that has no alternative route: do not mop the next section, and guard the wet section until it is dry. The supervisor arranges the time or an alternative route.
- Someone slips or falls on a wet floor: stop work and close the area. The workplace first aider or the emergency services attend to the casualty.
- The floor stays slippery after it is clean and dry, or there are loose or lifted tiles: close that section and report it. Assessment and repair are done by the party appointed by the building manager according to Chapter 39 · Buildings & Facilities.
- The water in the bucket is cloudy or oily, or the mop leaves dirty streaks: stop mopping. The solution, the rinse water, and the mop head are changed first, and the supervisor provides clean mop heads.
- The floor feels sticky after it dries or foams when wet: do not add product. The supervisor checks the method of use against the label and decides on rinsing.
- Blood or body fluid is spilled on the floor: do not mop it with daily floor cleaner. Trained personnel handle it according to the workplace infection control procedure.
- A container has no label, the label cannot be read, cleaning liquid is in a used drink bottle, or the safety data sheet is missing or past its validity date: do not use it. Hand it to the supervisor.
- Bleach, an acid cleaner, or another product is already in the bucket, or there is a pungent smell and the eyes sting: do not pour the floor cleaner, and leave the area. The supervisor and the occupational safety and health (K3) officer take over, and anyone short of breath is taken to the emergency services.
- Liquid gets in the eyes and the stinging does not go away after washing with plenty of water, or the skin of the hands is red, itchy, or cracked: stop wet work and report to the supervisor. Examination and treatment are done by a doctor.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
The product is neutral, so this work carries no risk.
Why is it wrong?
The risk comes from the wet floor and from wet work. A freshly mopped smooth floor is slippery, and prolonged contact with water and detergent can cause dermatitis.
Common misconception
The mop was wrung dry, so the floor can be walked on.
Why is it wrong?
Even a well-wrung mop leaves a thin film of water. A smooth floor is safe to walk on after it has dried completely.
Common misconception
A wet floor sign is enough.
Why is it wrong?
A cone only warns of the hazard. People are kept away with barriers, quiet working hours, or a dry path.
Common misconception
As long as it still foams, the solution is still good.
Why is it wrong?
The measures for changing are visible soil and time, for example every 1 to 2 hours. A cloudy solution returns soil to the floor.
Common misconception
The more product, the cleaner.
Why is it wrong?
A solution that is too strong can be as ineffective as one that is too weak, and the excess surfactant stays on the floor as residue.
Common misconception
Every spill gets mopped.
Why is it wrong?
A small water-based spill is wiped up with absorbent material until the floor is dry. Mopping it widens the wet floor.
Links to other chapters
Chapter 27 on neutral all-purpose cleaners gives the basics of dilution and residue used here, and Chapter 39 · Buildings & Facilities on floors and tiles holds slip testing. When the protective floor coating has gone dull and does not come up with daily mopping, the work is covered in Chapter 44 on floor finish strippers. Labels, transferring, and spills of chemicals are in Chapter 6 · Safety on chemicals in technician work.
Exercises and worked solutions
The figures in the problems are for practice.
Try to answer first, then open the worked solution.
A 5 liter jerry can holds the second product with a relative density of 1.010. How many kilograms does it hold, and how many grams of listed sulfate surfactants are in it?
Check my answer
See the worked solution
It holds kg, that is, 5,050 g. The listed sulfate surfactants are g to g, and the rest is not itemized on the data sheet.
A floor cleaner has a pH of 8.5. How many times is its hydroxide ion concentration against a neutral solution, and does that product fall in the neutral range of 6 to 8?
Check my answer
See the worked solution
pH 8.5 is units from neutral, that is, times in hydroxide ion concentration. The figure 8.5 is above 8, so that product is slightly basic and does not fall in the neutral range of 6 to 8.
The water in the solution bucket is already cloudy although it has been in use for just 40 minutes, and the worker intends to wait until two hours have passed. What is wrong?
Check my answer
See the worked solution
The interval of 1 to 2 hours is just one of the measures, and the other measure is visible soil. A cloudy solution is changed right then together with the rinse water and the mop head, because the mop has started to return soil to the floor.
The solution bucket is down to a quarter, and the worker pours new product on top of what is left. What is wrong?
Check my answer
See the worked solution
A solution container is not topped up over what is left, because that leftover already carries soil and its concentration is no longer known. The bucket is emptied and cleaned first, and then filled with new solution.
A lobby measuring 12 m by 9 m is mopped while leaving a dry path 1.5 m wide along the 12 m side. The mopping speed is 3 m² per minute and the drying time measured on site is 12 minutes. How long does it take until the whole lobby is clean and dry with a dry path available at all times?
Check my answer
See the worked solution
The lobby area is m² and its dry path is m², so the first section is m². The first section needs minutes of mopping and 12 minutes of drying, then the path needs minutes of mopping and 12 minutes of drying, so the total is minutes.
The vinyl floor of a ward has just been mopped shortly before visiting hours, and the worker has put out a single cone and nothing else. What is done?
Check my answer
See the worked solution
The wet section is closed with barriers or dried before visitors come in, and an alternative route is shown, because a cone does not prevent people from entering a wet, smooth floor. The supervisor then moves the mopping time for that ward to quiet hours.
References
External sources
- Slips and trips: The importance of floor cleaninghse.gov.uk
- Best Practices for Environmental Cleaning in Healthcare Facilities: in Resource-Limited Settingscdc.gov
- Safer Chemical Ingredients Listepa.gov
- Chemistry 2eopenstax.org
- Slips and trips in health and social carehse.gov.uk
- Safe use of cleaning substances in the hospitality industryhse.gov.uk
- How do I prevent skin problems in my business?hse.gov.uk
- Preservation Briefs 40: Preserving Historic Ceramic Tile Floorsnps.gov
- Slip, Trip, and Fall Prevention for Healthcare Workerscdc.gov
Revision history
| Date | Version | Change |
|---|---|---|
| November 15, 2026 | 1 | First published |
How to cite
Kurnia (2026). Daily floor cleaners: a ready-to-use neutral product and a product with sulfate surfactants, pH 7 to 9, mopping method and changing the solution, slippery floors and residue, and handling and storage. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/pembersih-lantai-harian-produk-netral-siap-pakai-dan-produk-bersurfaktan-sulfat-ph-7-sampai-9-cara-pel-dan-penggantian-larutan-lantai-licin-dan-sisa-serta-penanganan-dan-penyimpanan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
A 5 liter jerry can holds the second product with a relative density of 1.010. How many kilograms does it hold, and how many grams of listed sulfate surfactants are in it?
A floor cleaner has a pH of 8.5. How many times is its hydroxide ion concentration against a neutral solution, and does that product fall in the neutral range of 6 to 8?
The water in the solution bucket is already cloudy although it has been in use for just 40 minutes, and the worker intends to wait until two hours have passed. What is wrong?
Nearby chapters
Reading order by shelf: Chemistry · Chapter 46.
Reading order by shelf: Chemistry · Chapter 44.