Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Buildings & Facilities · Chapter 46Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Building accessibility for people with disabilities

    routes and ramps, handrails, accessible toilets, lifts and buttons, visual alarms and guidance paths, and periodic inspection

    A wheelchair user attending a conference at a hotel is held up at a side-entrance ramp that is too steep, finds the accessible toilet being used as a storeroom with the alarm cord wound up out of reach, and cannot reach the lift button; that night a Deaf guest in another room has no fire alarm light. This chapter covers building accessibility from the building technician’s side: routes, doors, and ramps together with the relationship between ramp gradient and length, handrails, accessible toilets and emergency assistance alarms, lifts and their buttons, visual alarms and hearing enhancement, tactile surfaces and guidance paths, and periodic inspection. The dimensions come from the English Approved Document M volume 2 (2015 edition with the 2020 and 2024 amendments) and the UK Department for Transport tactile paving guidance (December 2021); as of November 2026, the Indonesian requirements could not be confirmed from open documents. Altering ramps, doors, toilets, lifts, and alarm systems is work for designers, contractors, and authorized technicians.

    Section you’re reading: Chapter opening

    On the second day of a conference at a hotel in Yogyakarta, a participant who uses a wheelchair came in through a side entrance because the main lobby was taken up by an exhibition. The ramp at that entrance rose 450 mm over a length of 6 m, and the participant’s companion had to push from behind. On the ballroom floor, the accessible toilet held a stack of folding chairs, and its assistance alarm cord had been wound up so that cleaners would not pull it. The lift call button in the ballroom lobby was mounted 1,250 mm high and blocked by a banner stand. That night a Deaf guest on the seventh floor asked how they would know if the fire alarm went off, because the room had no warning light. The building technician needs to know which dimensions apply, how to check them, and which repairs belong to someone else.

    Scope

    This chapter covers the parts of a building that decide whether people with disabilities can enter, move around, use the facilities, and leave safely, together with their periodic inspection by the building technician. The dimensions in this chapter are English figures: Approved Document M volume 2 for buildings other than dwellings, 2015 edition with the 2020 and 2024 amendments, and the UK Department for Transport tactile paving guidance, December 2021 edition. As of November 2026, the Indonesian requirements on building ease of use, including Permen PUPR 14/2017 (Regulation of the Minister of Public Works and Housing), could not be confirmed from open documents; before using them for design, audits, or permits, check the current text and status with the building designer and the local technical agency.

    Lifts and their maintenance are covered in Chapter 24 to Chapter 27, including lift emergency response in Chapter 25. Automatic lobby doors are in Chapter 43, doors and door closers in Chapter 38, sensor-operated restrooms in Chapter 45, slippery floors in Chapter 39, fire alarms in Chapter 19 to Chapter 23 with audible and visual alarm devices in Chapter 22, and emergency lighting in Chapter 106 · Electrical & Control.

    Altering ramps, doors, toilets, lift cars or buttons, and fire alarms and emergency assistance alarms is outside the building technician’s authority; that work belongs to designers, building contractors, licensed lift contractors, and authorized alarm technicians. The building technician measures, checks the functions that users are meant to test, removes obstructions, records, and reports.

    Accessibility, people with disabilities, and the basis for the dimensions

    Accessibility is the ease a building provides so that everyone, including people with disabilities, can reach, enter, use, and leave the building independently and safely. Wheelchair users need level surfaces, gentle slopes, and turning space; people with visual impairments need cues they can feel, color contrast, and something to hold; people with hearing impairments and Deaf people need visual information in place of sound. Older people and guests pulling suitcases also use the same ramps and wide doors.

    Approved Document M is official guidance from the government of England for meeting the access requirements of that country’s building regulations. The document itself states that there are other ways of meeting the requirements, so there is no obligation to adopt any particular solution it contains. For building technicians in Indonesia, its figures are an inspection reference with a clear origin, not Indonesian requirements; if the building designer used other requirements, the designer’s dimensions are what get checked. Many barriers also come from daily use rather than design: goods in the route, the toilet turned into a storeroom, buttons blocked, and alarms that are never tested.

    Routes, doors, and ramps

    According to Approved Document M, corridors and passageways used by wheelchairs have an unobstructed width of at least 1,200 mm. Where they are narrower than 1,800 mm, passing places at least 1,800 mm long with an unobstructed width of at least 1,800 mm are provided at reasonable intervals, for example at corridor junctions. The unobstructed width is measured without projecting objects, so display tables, planters, and parked trolleys reduce the actual width.

    The effective clear width of a door is the width of the opening measured at right angles to the wall from the outside of the door stop on the closing side to the nearest obstruction on the hinge side, such as projecting door handles, the open door leaf, or the door stop. This width is always smaller than the width of the door leaf.

    Direction and width of approachNew buildings (mm)Existing buildings (mm)
    Straight-on, without a turn800750
    At right angles to an access route at least 1,500 mm wide800750
    At right angles to an access route at least 1,200 mm wide825775
    External doors to buildings used by the general public1,000775

    For self-closing entrance doors, Approved Document M calls for a powered door system when the door cannot be opened with a force of no more than 30 N at the leading edge from the closed position to 30 degrees open, and no more than 22.5 N from 30 to 60 degrees. A door closer set too hard is reported under Chapter 38.

    A ramp is a sloping route that replaces or accompanies a stair for a change of level. The longer a single flight, the gentler the ramp has to be, because wheelchair users run out of strength and find it hard to stop when going down. Approved Document M gives the following limits for a single flight:

    Going of a flightMaximum gradientMaximum rise
    10 m1:20500 mm
    5 m1:15333 mm
    2 m1:12166 mm

    For goings between 2 m and 10 m, the guidance allows interpolation and gives the examples 1:14 for 4 m and 1:19 for 9 m. The three table rows and both examples follow one simple relationship:

    n=g+10,rmax=gg+10,gmin=10 r1−rn = g + 10, \qquad r_{max} = \frac{g}{g + 10}, \qquad g_{min} = \frac{10\, r}{1 - r}

    where gg is the going of the flight (m), the maximum gradient is 1:nn, rmaxr_{max} is the maximum rise (m), and gming_{min} is the shortest going for a rise rr (m). This relationship holds only for gg between 2 m and 10 m; no flight has a going greater than 10 m or a rise of more than 500 mm.

    Other requirements for ramps:

    • where the total rise is greater than 2 m, an alternative means of access for wheelchair users is provided, for example a lift;
    • the surface width between walls or kerbs is at least 1.5 m;
    • the surface is slip resistant when wet and contrasts in color with the landings;
    • landings at the foot and head of the ramp are at least 1.2 m long and intermediate landings at least 1.5 m long, both clear of door swings;
    • intermediate landings of 1,800 mm by 1,800 mm serve as passing places when one end of the ramp cannot be seen from the other or the ramp has three flights or more;
    • all landings are level, with a maximum gradient of 1:60 along their length and a maximum cross-fall of 1:40;
    • there is a handrail on both sides, and a contrasting kerb at least 100 mm high on any open side;
    • clearly signed steps are also provided when the rise of the ramp is greater than 300 mm.

    Approved Document M also notes that some people with disabilities who can walk find steps easier than a ramp. That is why steps and ramps are often built side by side.

    Handrails

    A handrail is a grip rail that runs continuously along a ramp or stair for support and guidance. Its ends also signal that a change of level begins or ends.

    For external ramps and stairs, Approved Document M sets the following dimensions:

    • the top of the upper handrail is 900 to 1,000 mm above the pitch line of the ramp or stair surface, and 900 to 1,100 mm above the surface of a landing;
    • the handrail is continuous across flights and landings and extends at least 300 mm horizontally beyond the head and foot of the ramp or the top and bottom nosings, without projecting into the access route;
    • the profile is circular with a diameter of 32 to 50 mm, or non-circular, 50 mm wide and 39 mm deep with rounded edges of at least 15 mm radius;
    • the clearance to the wall is 50 to 75 mm, with a clearance of at least 50 mm between a cranked support and the underside of the rail;
    • it contrasts with its background without being highly reflective, is slip resistant, and ends in a way that does not catch clothing.

    Common findings are loose supports, ends cut short to make room for a sign, and flaking paint that leaves a sharp surface. Supports are tightened according to the installation drawing; anchors that have come loose from the wall or floor are handed over to the contractor.

    Accessible toilets and emergency assistance alarms

    A wheelchair-accessible unisex toilet is a self-contained toilet room that can be used by a wheelchair user and a companion of either sex. Approved Document M treats it as the preferred option for wheelchair users because a companion of a different sex can come in to help.

    Room dimensions and layout in that guidance:

    • the room is at least 1,500 mm by 2,200 mm excluding projecting heat emitters, with a wheelchair turning space of 1,500 mm by 1,500 mm; where there is only one toilet in the building, the width is increased from 1.5 m to 2 m and a standing-height washbasin is added;
    • the transfer space beside the WC is kept clear to the back wall;
    • the door preferably opens outward, has a horizontal closing bar on the inside face, and has an emergency release so that it can be opened from outside;
    • a wheelchair user does not have to travel more than 40 m on the same floor to reach the toilet;
    • heat emitters are screened or their surfaces kept below 43 °C.

    An emergency assistance alarm is a pull-cord system for calling for help from an accessible toilet or bedroom. Approved Document M calls for this system to have visual and audible indicators confirming that the call has been received, a reset control reachable from a wheelchair and from the WC, and a signal distinguishable visually and audibly from the fire alarm. The pull cord is red, located as close to a wall as possible, and has two red bangles of 50 mm diameter, one at 100 mm and the other at 800 to 1,000 mm above the floor. The low bangle is there because a person who has fallen to the floor must still be able to pull it, so a cord wound up out of reach makes the alarm useless exactly when it is most needed.

    For accessible bedrooms, the guidance calls for a call signal outside the room and at a central control point. In a hotel, that point is usually the front desk or the security room, so alarm tests involve the staff on duty there.

    Lifts and buttons

    Approved Document M gives the following dimensions for passenger lifts:

    • the smallest car is 1,100 mm wide and 1,400 mm deep, enough for one wheelchair user and one companion;
    • an unobstructed maneuvering space of 1,500 mm by 1,500 mm, or a straight access route 900 mm wide, in front of the lift door;
    • power-operated sliding doors with an effective clear width of at least 800 mm, with timing devices and re-opening activators so that users and assistance dogs have time to get in and out;
    • car controls 900 to 1,200 mm high, preferably 1,100 mm, and at least 400 mm from any return wall; landing call buttons 900 to 1,100 mm high and at least 500 mm from any return wall;
    • audible and visual indication of lift arrival and location, in the car and in the lift lobby;
    • a mirror in a car that is too small to turn around in.

    The guidance also calls for raised button symbols that can be read by touch, buttons that contrast with their face plate, a handrail at a nominal 900 mm on at least one wall of the car, and an emergency communication system.

    What changes most often is the surroundings: a banner in front of the call button, a dead button light, the floor announcement switched off, and a dirty door sensor that makes the door close too quickly. The technician removes obstructions; buttons, sensors, announcements, and door timing belong to the licensed lift contractor (Chapter 24).

    Visual alarms, hearing enhancement, and evacuation

    Approved Document M calls for every fire alarm in sanitary accommodation to emit a visual and audible signal, and for every bedroom in buildings such as hotels to have a visual fire alarm signal. Visual alarm devices on fire alarm systems are covered in Chapter 22, and their testing in Chapter 23.

    The UK government guidance on means of escape for disabled people gives priority to flashing beacons on the fire alarm system and paging systems for alerting people with hearing impairments, and asks for all pagers and similar equipment to be tested regularly. Vibrating devices lent to Deaf guests are recorded, kept charged, and tested together with the alarm system.

    A hearing enhancement system is a system that sends a speaker’s voice directly to the user’s hearing aid, for example an induction loop, infrared, or radio system. Approved Document M calls for one in meeting rooms and at service counters that are noisy or behind glass, marked with the standard symbol. An induction loop with a broken cable looks the same from outside, so it has to be tested.

    A personal emergency evacuation plan (PEEP) is a written plan for how a person who needs assistance gets out of the building in an emergency. The UK guidance calls for these plans to be practiced at least every six months, forbids leaving people in a refuge to wait for the fire and rescue service, and for wheelchair users gives priority to horizontal evacuation into another fire compartment or out of the building, or to an evacuation lift. An ordinary lift is used for evacuation only if the building’s evacuation plan specifies it (Chapter 25 on lift emergency response); drills are covered in Chapter 14 · Safety on fire evacuation drills in hotels.

    Tactile surfaces and guidance paths

    A tactile paving surface is a floor surface with a raised texture that can be felt underfoot or with a cane, used to warn or guide people with visual impairments. According to the UK Department for Transport guidance, the blister pattern is only for pedestrian crossing points, while the corduroy pattern means hazard, proceed with caution, for example at the top and bottom of stairs; its bars are rounded, 6 mm high with a tolerance of 0.5 mm, 20 mm wide, spaced 50 mm center to center, and laid across the direction of travel.

    At stairs, the corduroy pattern is laid across the full width of the stair at the top and bottom, where possible starting 400 mm from the first nosing, to a depth of 800 mm where the stair is in the direct line of travel, and extending at least 400 mm beyond the stair on both sides, but not across an adjacent ramp or lift.

    A guidance path surface is a tactile surface with raised flat-topped bars running in the direction of travel, used to guide people where the usual cues, such as a building line, are missing. Its bars are 5.5 mm high with a tolerance of 0.5 mm, 35 mm wide, and spaced 45 mm apart. The path is 800 mm wide, kept as straight as possible, and has an unobstructed space of at least 800 mm on both sides, partly for guide dogs. An exhibition placed on top of a guidance path cuts it off like a wall.

    The raised profile has to be maintained: blisters that wear below 3 mm high are virtually undetectable, and the other patterns lose effectiveness when their height falls below the lower tolerance. Tactile tiles that are worn, loose, or replaced with plain tiles after floor repairs are recorded as findings.

    Periodic inspection

    Accessibility features fail silently, so the building technician checks them against a fixed list together with housekeeping and security. The list below is compiled from the requirements above.

    ItemWhat is checkedInterval
    Routes, corridors, and rampsunobstructed width not blocked, surface not slippery or damageddaily and at every major event
    Doorsclear width not reduced, opening force not heavy, automatic doors workingmonthly
    Handrailsfirm, continuous, ends not cutmonthly
    Accessible toiletsnot a storeroom, turning space clear, alarm cord hanging free, alarm and reset testedweekly
    Liftsspace in front of buttons clear, lights and announcements working, doors not closing too quicklydaily, reported to the contractor
    Visual alarms and aidswarning lights included in alarm tests, vibrating devices charged, induction loops testedalarm test schedule and before events
    Tactile surfacesnot worn, not loose, not covered by goods or carpetmonthly

    Results are recorded with the date, measurements, and follow-up. Measurements are taken with a tape, not estimated, because a shortfall of 35 mm at a door or 75 mm in a ramp rise is enough to stop a wheelchair. Complaints from guests and staff with disabilities are recorded as findings, because they are the quickest to discover new barriers.

    Worked example

    The numbers in the examples below are practice figures unless their origin is stated.

    Example 1: planning the length of a new ramp. A hotel side entrance is 420 mm higher than the sidewalk. The shortest going is gmin=10×0.42/(1−0.42)=7.24g_{min} = 10 \times 0.42/(1 - 0.42) = 7.24 m, with a gradient of 1:nn and n=7.24+10=17.24n = 7.24 + 10 = 17.24, or about 1:17. Adding landings of 1.2 m each at the foot and head, the total length on the ground is 7.24+1.2+1.2=9.647.24 + 1.2 + 1.2 = 9.64 m. A rise of 420 mm is more than 300 mm, so signed steps are also provided next to the ramp.

    Example 2: checking an existing ramp. The ramp in the opening case rises 450 mm over a 6 m going, a gradient of 6,000/450=1:13.36{,}000/450 = 1:13.3. For a 6 m going, the maximum gradient is 1:16 and the maximum rise 6/16=0.3756/16 = 0.375 m, or 375 mm, so the ramp is 450−375=75450 - 375 = 75 mm too high. The going needed for a 450 mm rise is gmin=10×0.45/0.55=8.18g_{min} = 10 \times 0.45/0.55 = 8.18 m. The finding is reported to the designer with a proposal to lengthen the ramp.

    Example 3: a level difference too large for a ramp. A restaurant terrace is 2.4 m above the parking area. With a longest flight of 10 m and a largest rise of 500 mm per flight, 2,400/500=4.82{,}400/500 = 4.8 is needed, rounded up to 5 flights, each rising 480 mm with a going of 20×0.48=9.620 \times 0.48 = 9.6 m. The total length is 5×9.6+4×1.5+2×1.2=56.45 \times 9.6 + 4 \times 1.5 + 2 \times 1.2 = 56.4 m. The total rise is above 2 m, so an alternative such as a lift is still provided.

    Example 4: a door and corridor in a new wing. A meeting room door in a new hotel wing is approached at right angles from a corridor 1,400 mm wide, and its effective clear width measures 790 mm. A 1,400 mm corridor falls in the at least 1,200 mm class, so a new building needs 825 mm; the shortfall is 825−790=35825 - 790 = 35 mm. The corridor is also narrower than 1,800 mm, so passing places are needed at junctions.

    Example 5: the accessible toilet and the alarm cord. The accessible toilet on the ballroom floor measures 1,600 mm by 2,050 mm. Its width exceeds 1,500 mm by 1,600−1,500=1001{,}600 - 1{,}500 = 100 mm, but its depth is 2,200−2,050=1502{,}200 - 2{,}050 = 150 mm short of 2,200 mm, so the finding is recorded for the designer. The alarm cord has been wound up so that its end is 1,900 mm above the floor, whereas the lower bangle must be at 100 mm; a person who has fallen would have to reach 1,900−100=1,8001{,}900 - 100 = 1{,}800 mm higher. The cord is released, the folding chairs are removed, and the alarm is tested.

    Example 6: lift buttons and tactile surface at a stair. The lift call button is mounted 1,250 mm high, 1,250−1,100=1501{,}250 - 1{,}100 = 150 mm above the 1,100 mm limit, and is reported to the lift contractor. The 1.6 m wide stair next to it receives a corduroy surface 1.6+2×0.4=2.41.6 + 2 \times 0.4 = 2.4 m wide and 0.8 m deep, that is 2.4×0.8=1.922.4 \times 0.8 = 1.92 m² per landing. With 400 mm by 400 mm modules, one landing needs (2.4/0.4)×(0.8/0.4)=12(2.4/0.4) \times (0.8/0.4) = 12 modules, and the top and bottom of the stair 2×12=242 \times 12 = 24 modules.

    Stop conditions

    1. A route, ramp, or exit door used by people with disabilities is blocked, slippery, or damaged while the building is in use: do not leave the route open without supervision; remove the obstruction, direct users to another equivalent route, and report the damage to the building management.
    2. The emergency assistance alarm in an accessible toilet or bedroom does not sound, does not light, does not reach the control point, or cannot be reset: close the facility or post staff to check it at intervals, and hand the repair over to an authorized alarm technician.
    3. The fire alarm warning light in an accessible bedroom or toilet does not light during a test: do not place Deaf guests or guests with hearing impairments in that room; the front desk moves the guest or provides a tested aid, and the fire alarm technician repairs it (Chapter 23).
    4. The lift door closes before a wheelchair user has finished getting in or out, the door does not re-open when obstructed, or the floor indication does not work: take that lift out of public use and hand it over to the licensed lift contractor (Chapter 24 on lifts in buildings).
    5. The repair would require changing a ramp gradient, removing a door, rearranging a toilet, or altering the lift car and buttons: stop; the decision belongs to the building designer and the execution to an authorized contractor.
    6. During a fire alarm, a person with a disability cannot use the stairs and there is no evacuation lift: do not use an ordinary lift unless the building’s evacuation plan specifies it, and do not leave the person alone in a refuge; carry out the personal evacuation plan, notify the building fire wardens and the evacuation coordinator, and then the fire and rescue service.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    A longer ramp can be made as steep as a short one.

    Why is it wrong?

    The opposite is true. The longer the flight, the gentler the ramp has to be: 1:12 is only for a 2 m going, while a 10 m going is at most 1:20.

    Common misconception

    The door leaf width is the same as the clear width.

    Why is it wrong?

    The effective clear width is measured from the door stop to the obstruction on the hinge side, including handles and the open leaf, so it is always smaller than the leaf width.

    Common misconception

    The alarm cord should be wound up so that it is not pulled by accident.

    Why is it wrong?

    The lower bangle at 100 mm is placed there deliberately for a person who has fallen. A wound-up cord defeats the purpose of the alarm.

    Common misconception

    A loud fire alarm is enough for every guest.

    Why is it wrong?

    People with hearing impairments need a visual signal or a vibrating device, and that device needs to be tested together with the alarm system.

    Lifts are maintained according to Chapter 24 on lifts in buildings, and trapped passengers are handled according to Chapter 25. Heavy doors are checked with Chapter 43 on automatic lobby doors and Chapter 38 on door closers, and slippery ramps are tested with Chapter 39 on slippery floors and slip testing. Fire alarm warning lights are among the alarm devices in Chapter 22 and are tested according to Chapter 23. Sensor-operated fittings in accessible toilets follow Chapter 45, and personal evacuation plans are practiced together with Chapter 14 · Safety on fire evacuation drills in hotels.

    Exercises and worked solutions

    The numbers in the exercises are for practice.

    Try to answer first, then open the worked solution.

    1. A ramp with a 3 m going rises 250 mm. Does it meet the Approved Document M limit, and what going is needed?

      Check my answer
      See the worked solution

      For a 3 m going, n=3+10=13n = 3 + 10 = 13, so the maximum rise is 3/13=0.2313/13 = 0.231 m or 231 mm, and a 250 mm ramp is too steep. The going needed is gmin=10×0.25/0.75=3.33g_{min} = 10 \times 0.25/0.75 = 3.33 m, so the ramp is lengthened by about 0.33 m by the contractor according to the designer’s drawing.

    2. A new hotel in England has 145 bedrooms. How many wheelchair-accessible bedrooms does Approved Document M call for, and what alarm equipment must those rooms have?

      Check my answer
      See the worked solution

      The guidance calls for at least one wheelchair-accessible bedroom for every 20 bedrooms or part thereof, so 145/20=7.25145/20 = 7.25 is rounded up to 8 rooms. Every bedroom has a visual fire alarm signal, and the accessible bedrooms also have a pull-cord emergency assistance alarm that can be reached from the bed and from the floor.

    3. Why must the emergency assistance alarm signal be distinguishable from the fire alarm?

      Check my answer
      See the worked solution

      The staff member receiving the call has to know whether one person in one room needs help or the whole building has to be evacuated. If the two signals are the same, an assistance call can be mistaken for a fire alarm or, the other way around, ignored, so help arrives late.

    4. A ramp handrail measures 850 mm above the ramp surface and extends 200 mm beyond the head of the ramp. What are the findings?

      Check my answer
      See the worked solution

      A height of 850 mm is below the range of 900 to 1,000 mm above the pitch line of the ramp, and an extension of 200 mm is less than 300 mm. Both findings are recorded and handed over to the contractor, because moving the handrail requires new anchors.

    5. The bars of the corduroy surface at the top of the lobby stair measure 4.2 mm high. What does this mean, and what is done?

      Check my answer
      See the worked solution

      Corduroy bars are designed 6 mm high with a tolerance of 0.5 mm, so the lower limit is 5.5 mm and 4.2 mm is already below it. Its effectiveness as a warning is reduced, so the tiles are recorded for replacement and the top of the stair is given a temporary marker.

    6. The fire alarm sounds while a staff member who uses a wheelchair is on the fifth floor. The building’s lift is not an evacuation lift. What is done?

      Check my answer
      See the worked solution

      The staff member is not taken down in an ordinary lift, because that lift is not designed for evacuation and the building’s evacuation plan does not specify it. Trained staff carry out the personal evacuation plan, the staff member is not left alone in a refuge, and the evacuation coordinator and the fire and rescue service are told where they are.

    References

    External sources

    • Approved Document M: Access to and use of buildings, Volume 2: Buildings other than dwellings, 2015 edition incorporating 2020 and 2024 amendmentsassets.publishing.service.gov.uk
    • Guidance on the Use of Tactile Paving Surfacesassets.publishing.service.gov.uk
    • Fire safety risk assessment: means of escape for disabled people (accessible version)gov.uk

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Building accessibility for people with disabilities: routes and ramps, handrails, accessible toilets, lifts and buttons, visual alarms and guidance paths, and periodic inspection. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/aksesibilitas-bangunan-untuk-penyandang-disabilitas-jalur-dan-ram-pegangan-rambat-toilet-aksesibel-lift-dan-tombol-alarm-visual-dan-jalur-pemandu-serta-pemeriksaan-berkala

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated
    1

    A ramp with a 3 m going rises 250 mm. Does it meet the Approved Document M limit, and what going is needed?

    2

    A new hotel in England has 145 bedrooms. How many wheelchair-accessible bedrooms does Approved Document M call for, and what alarm equipment must those rooms have?

    3

    Why must the emergency assistance alarm signal be distinguishable from the fire alarm?

    Self-assessment progress0%

    Nearby chapters