Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Biology & Microbiology · Chapter 40Quantitative

    By Kurnia · Published November 10, 2026 · Version 1 · 22 min read

    Muscles, bones, and joints at work

    muscle fibers and contraction, muscle fatigue, the spine and discs, body levers and forces on the back, repetitive injuries to the hands, and working posture

    A hotel laundry operator bends into a washing machine drum to pull out wet linen, and a coworker at the folding table feels tingling in their fingers at night. This chapter explains how skeletal muscle works from the fiber down to the sarcomere, the roles of calcium and ATP, motor units and recruitment, energy sources and muscle fatigue, the spine with its discs and ligaments, bones and joints as levers, the force on the back muscles when bending, synovial joints, bursae, and the carpal tunnel, and the meaning of horizontal distance in the NIOSH lifting equation. The chapter gives no diagnosis, medication advice, or individual medical limits; complaints are referred to the company doctor.

    Section you’re reading: Chapter opening

    In a hotel laundry, an operator unloads a large-capacity washing machine the same way every day: feet planted on the floor, body bent into the drum, then a bundle of wet sheets pulled out with the hands reaching far in front of the body and swung toward the trolley beside them. After a few weeks the operator complains of an aching lower back at the end of every shift, and one morning the pain spreads into the thigh. At the folding table, a coworker folds towels thousands of times per shift and starts waking at night because their fingers are tingling. Why does the same load feel much heavier when it is lifted from inside the drum, and why can a movement as light as folding towels cause trouble in the hands? The answer lies in how muscles produce force, how bones work as levers, and how soft tissue responds to repeated loading; the calculations are in Examples 2 to 6.

    Scope

    This chapter covers skeletal muscle, the spine, joints, and body levers, and what they mean for working posture. Lifting equipment, slings, and trolleys are in Chapter 9 · Safety; laundry ergonomic hazards and the full assessment with the NIOSH lifting equation are in Chapter 21 · Laundry on laundry occupational safety and health (K3); moments of force are in Chapter 1 · Mechanical & Mechatronics on force and torque and Chapter 8 · Physics on static equilibrium; hazard identification is in Chapter 3 · Safety; personal protective equipment is in Chapter 5 · Safety; hand-arm vibration is in Chapter 7 · Safety; and motor nerves are in Chapter 33 on nerves and the brain.

    This chapter gives no diagnosis, medication advice, or load limits for any particular person. Pain, numbness, and muscle weakness are examined by a doctor or the company doctor.

    Skeletal muscle: from fiber to sarcomere

    Skeletal muscle produces movement, but it also resists movement: muscles work against gravity to maintain posture, keep joints in place, and produce heat. Its connective tissue is arranged in three layers: the epimysium around the muscle, the perimysium around bundles of fibers (fascicles), and the endomysium around each fiber. The collagen of these three layers merges with the tendon, and the tendon merges with the periosteum of the bone, so the tension of the fibers is passed on until it pulls on the bone.

    A skeletal muscle fiber is a long, multinucleated cell up to 100 µm in diameter and up to 30 cm long in the thigh muscles. Inside it lie myofibrils about 1.2 µm in diameter. A sarcomere is the smallest contractile unit of a muscle fiber, the part of a myofibril from one Z-line to the next, about 2 µm long. Inside the sarcomere, thin actin filaments anchored to the Z-lines overlap with thick myosin filaments anchored at the M-line. This repeating arrangement of dark and light bands is what makes skeletal muscle look striated.

    Each skeletal muscle fiber contracts only when commanded by a nerve. A motor neuron from the spinal cord releases acetylcholine at the neuromuscular junction, the fiber membrane depolarizes, and an action potential spreads along the membrane and into the T-tubules that reach into the fiber. The details of the action potential are in Chapter 33 on nerves and the brain.

    Contraction: calcium, cross-bridges, and ATP

    The action potential in the T-tubules opens calcium channels in the sarcoplasmic reticulum, the store of calcium ions inside the fiber. The released calcium binds to troponin, so tropomyosin shifts and uncovers the myosin-binding sites on actin. A cross-bridge is a temporary bond between a myosin head and actin. The myosin head pulls the actin toward the M-line by roughly 10 nm in one stroke, releases, is cocked again with energy from the breakdown of ATP, and then binds and pulls again. In this sliding filament model, the sarcomere shortens because the thin filaments slide between the thick filaments, while the filaments themselves do not shrink.

    ATP is needed in two places: new ATP binding to the myosin head releases the cross-bridge, so without ATP the muscle becomes rigid, and ATP drives the pump that returns calcium to the sarcoplasmic reticulum. The muscle relaxes when the motor neuron stops signaling and the calcium is pumped back.

    A concentric contraction shortens the muscle to move a load, for example lifting a bucket; an eccentric contraction lengthens a muscle that stays tense, for example lowering a bucket slowly. An isometric contraction is a contraction that produces tension without changing the joint angle, such as holding a posture or holding a load still in front of the body. Work that looks light, such as holding a spray hose overhead or holding a steam iron in the same position, is largely isometric work.

    Controlling force: motor units, recruitment, and muscle length

    A motor unit is one motor neuron together with all the muscle fibers it innervates. In the eye muscles one neuron serves about six fibers, and the finger muscles also use small units for fine movement; in the thigh and back muscles one neuron can serve thousands of fibers for strong, gross movements.

    Recruitment is the activation of more and larger motor units to increase muscle force. Small, low-threshold units are active first, and large units join in as the required force increases; in some muscles, the largest motor units can produce 50 times the force of the smallest. Maximum force with all units active cannot be sustained for long, so the nervous system usually rotates units: some rest while others work. Stimuli that arrive before the previous twitch has finished also add up tension, to about three to four times the tension of a single twitch in incomplete tetanus.

    Force also depends on sarcomere length. Cross-bridges form only in the region where actin and myosin overlap, so maximum tension is reached at 80 to 120 percent of resting length. A sarcomere stretched too far loses overlap, while a sarcomere that is too short runs out of room to slide; both produce less tension. This is why joints in extreme positions, such as an arm fully extended into the drum or a sharply bent wrist, make the same force require greater recruitment.

    Energy sources and muscle fatigue

    The ATP stored in muscle is enough for only a few seconds of contraction, so it must be continually remade. Creatine phosphate supplies ATP very quickly through the enzyme creatine kinase, but only for about 15 seconds. After that, anaerobic glycolysis breaks glucose down into two ATP and two molecules of pyruvic acid; when oxygen is short, pyruvic acid is converted into lactic acid. Glycolysis lasts only about one minute of muscle work. Aerobic respiration in the mitochondria is far more efficient, producing about 36 ATP per molecule of glucose, and supplies about 95 percent of the ATP of muscle at rest or in moderate work, but it is slower and requires a continuous supply of oxygen.

    Muscle fatigue is the state in which a muscle can no longer contract in response to nerve signals. Its exact cause is not yet fully known. Factors associated with it include falling ATP reserves, lactic acid lowering the pH inside the cell, an imbalance of sodium and potassium ions that disturbs calcium release, and damage to the sarcoplasmic reticulum after long, heavy work. Oxygen debt is the amount of oxygen needed to make up for the ATP produced without oxygen; this is why breathing stays fast for a while after heavy work stops.

    Slow oxidative fibers are rich in mitochondria and myoglobin, resist fatigue, and are abundant in the postural muscles that hold the back upright; fast glycolytic fibers produce large forces but tire quickly; fast oxidative fibers lie in between. Holding a load motionless still uses ATP, so it is not rest for the muscle. Mechanical stress stimulates bone to deposit mineral and collagen, whereas incorrect exercise, loads that are too heavy, or too little recovery time can injure muscles, tendons, or bones.

    The spine, discs, and ligaments

    The adult spine consists of 24 vertebrae (7 cervical, 12 thoracic, 5 lumbar) plus the sacrum and coccyx, with four curves that add strength, flexibility, and the ability to absorb shock. The lumbar vertebral bodies are the largest and thickest because they carry the largest share of body weight.

    An intervertebral disc is a fibrocartilage pad that fills the gap between, and joins, the bodies of two adjacent vertebrae. Its outer layer, the anulus fibrosus, is tough and fibrous; its center, the nucleus pulposus, is soft, gel-like, and rich in water that resists compression. The discs are thinnest in the neck and thickest in the lower back, and together they account for about 25 percent of the height of the body between the top of the pelvis and the base of the skull. The water content of the nucleus pulposus decreases with age, so the discs thin and become less flexible. The ligament in front of the vertebral bodies resists bending backward, while the ligament behind them supports the column when bending forward.

    When the body bends forward, the front of the disc is compressed and its back is stretched. A herniated disc is the condition in which the nucleus pulposus bulges backward through a weakened anulus fibrosus. The pressure of bending while lifting a heavy object can trigger it if the back of the anulus is already weak from injury or age. The bulge can press on a spinal nerve where it exits, causing pain or muscle weakness in the area that nerve serves. The most common sites are the L4/L5 and L5/S1 discs, which can cause pain radiating from the lower back into the thigh and leg. Workers cannot tell for themselves the cause of symptoms like those in the opening case; the examination is done by a doctor.

    Body levers and forces on the back

    Bones work as levers and joints as fulcrums; bones do not move unless a muscle that crosses the joint contracts. The load can be an object being lifted or a part of the body itself, and the effort force comes from muscle contraction. A moment arm is the perpendicular distance from the fulcrum to the line of action of a force. At rest, the moment of the muscle force about the joint equals the sum of the moments of the loads:

    Fmuscle dmuscle=∑Wi di,W=m g,KM=dmuscledloadF_{muscle}\,d_{muscle} = \sum W_i\,d_i, \qquad W = m\,g, \qquad KM = \frac{d_{muscle}}{d_{load}}

    where FmuscleF_{muscle} is the pulling force of the muscle (N), dmuscled_{muscle} the moment arm of the muscle (m), WiW_i the weight of each load (N), did_i the moment arm of each load (m), mm the mass (kg), g=9.81g = 9.81 m/s², and KMKM the dimensionless mechanical advantage. This formula assumes static conditions, forces perpendicular to the moment arm, and one muscle standing for the whole muscle group; the details of moments are in Chapter 1 · Mechanical & Mechatronics and Chapter 8 · Physics.

    In a third-class lever such as the elbow, the muscle attaches between the joint and the load, a few centimeters from the joint, while the load in the hand is tens of centimeters away. The mechanical advantage is less than one: the muscle pulls with several times the weight of the load, but the hand moves far and fast. When the body bends, the hip joint becomes the fulcrum, the weight of the upper body and the load in the hands lie far in front of it, and the erector muscles of the back pull with a short moment arm behind the spine. That large muscle force, plus the weight being supported, compresses the lumbar discs. In a rough model that treats all forces as parallel to the axis of the spine,

    Fcomp≈Fmuscle+∑WiF_{comp} \approx F_{muscle} + \sum W_i

    where FcompF_{comp} is the compressive force on the disc (N). This model only gives an idea of the magnitude, not a value to compare with a medical limit; more complete models take into account the angle of the trunk and many muscles.

    Doubling the distance of the load from the body doubles its moment, and because the moment arm of the back muscles stays the same, the muscle force and the compression of the disc rise almost in proportion. Straightening the body shortens the moment arm of the upper body, so most of the moment disappears even though the load is the same.

    Synovial joints, bursae, and repetitive injuries to the hands

    Synovial joints such as the shoulder, elbow, wrist, and knee are enclosed in a capsule filled with synovial fluid, which lubricates and nourishes the articular cartilage, because that cartilage has no blood vessels. Ligaments limit excessive movement, while the muscles and tendons that cross the joint act as dynamic ligaments that tighten more strongly as the load increases.

    A bursa is a thin connective tissue sac filled with lubricating fluid that separates skin, muscle, or tendon from the bone beneath. A tendon sheath is a similar, smaller sac that wraps a tendon where the tendon crosses a joint. Inflammation of a bursa can arise from muscle overuse, trauma, or excessive and prolonged pressure on the skin. Inflammation of the bursa in front of the kneecap is known as housemaid’s knee and is now more often seen in roofers, floor layers, or carpet layers who do not use knee pads. Housekeeping staff who kneel to clean bathrooms are under similar pressure.

    The wrist has the carpal tunnel, a passage whose walls and floor are formed by the carpal bones and whose roof is formed by the flexor retinaculum, a strong ligament on the front of the wrist. The tendons of nine forearm muscles and one important nerve pass through this narrow passage. Overuse of the tendons, poor ergonomics, or a wrist injury can inflame the contents of the passage and compress the nerve, resulting in carpal tunnel syndrome with pain or numbness and weakness in the area of the hand that the nerve serves. Repetitive use of the upper arm, especially raising the arm away from the body, can also inflame the bursae and tendons of the shoulder.

    Osteoarthritis, the most common form of joint inflammation, is associated with age and wear of the articular cartilage, with risk factors that include joint injury, physical work, and excess body weight. The load on joints and tendons is cumulative: a single light movement is not dangerous, but thousands of the same movements per shift with a bent wrist and short recovery times load the same tissue over and over.

    Working posture and the NIOSH lifting equation

    NIOSH, the United States occupational safety agency, developed the revised lifting equation to assess two-handed lifting tasks. The recommended weight limit (RWL) is the product of the load constant and six task multipliers:

    RWL=LC×HM×VM×DM×AM×FM×CM,LI=LRWLRWL = LC \times HM \times VM \times DM \times AM \times FM \times CM, \qquad LI = \frac{L}{RWL}

    where LC=23LC = 23 kg is the load constant, the maximum recommended load under ideal conditions; HMHM the multiplier for the horizontal distance of the hands from the midpoint between the ankles; VMVM the multiplier for the height of the hands above the floor; DMDM the multiplier for the vertical travel distance of the lift; AMAM the multiplier for the twist angle of the body; FMFM the frequency multiplier; CMCM the coupling multiplier; LL the actual weight of the load (kg); and LILI the dimensionless lifting index. Tasks with a lifting index above 1 carry an increased risk of lifting-related low back pain. According to NIOSH’s own document, this equation has not yet been fully validated, and it assesses the task, not the capacity of a particular person.

    The horizontal multiplier in metric units is HM=25/HHM = 25/H with HH in centimeters, with a value of 1.00 for a distance of 25 cm or less, 0.83 at 30 cm, 0.63 at 40 cm, and 0.50 at 50 cm. This form agrees with the lever formula: doubling the distance of the load doubles the moment about the back, and the recommended load drops by half. The vertical multiplier is 0.99 at 70 cm and 0.93 at 50 cm or 100 cm, because lifting from near the floor requires bending the body, while lifting far above the waist moves the arms away from the body.

    The twist angle multiplier is 1.00 with no twist, 0.90 at 30°, 0.86 at 45°, 0.81 at 60°, and 0.71 at 90°; the travel distance multiplier is 1.00 for a distance of 25 cm or less. The full assessment with the frequency and coupling tables is covered in Chapter 21 · Laundry on laundry K3.

    From the body’s side, good working posture follows from the previous sections: the load close to the body so that its moment arm is short; the back upright and the knees bent so that the discs are not compressed while bending forward; turning by stepping the feet, not twisting the waist; joints working in the middle of their range; and repetitive tasks rotated and given breaks. Engineering controls such as raised-base trolleys, waist-high tables, or lifting aids are stronger than relying on technique, as in Chapter 9 · Safety and Chapter 21 · Laundry.

    Worked example

    The numbers in the examples below are practice numbers unless their source is stated. The acceleration due to gravity is g=9.81g = 9.81 m/s².

    Example 1: the elbow lever when holding a bucket. A technician holds a bucket of 4 kg with the forearm horizontal. The upper arm muscle attaches 4 cm from the elbow joint, and the bucket handle is 32 cm from the elbow; the weight of the forearm is neglected. The weight of the bucket is W=4×9.81=39.24W = 4 \times 9.81 = 39.24 N. Moment equilibrium gives Fmuscle=39.24×32/4=313.92F_{muscle} = 39.24 \times 32/4 = 313.92 N, about 314 N, which is 8 times the weight of the bucket. The mechanical advantage is KM=4/32=0.125KM = 4/32 = 0.125. The elbow trades force for reach.

    Example 2: bending into the drum. The operator in the opening case bends and pulls 15 kg of wet linen with the hands 45 cm in front of the hip joint. Their upper body has a mass of 40 kg with its center of mass 25 cm in front of that joint, and the moment arm of the back erector muscles is 5 cm. The moment of the load is 15×9.81×0.45=66.2215 \times 9.81 \times 0.45 = 66.22 N·m and the moment of the body is 40×9.81×0.25=98.1040 \times 9.81 \times 0.25 = 98.10 N·m, for a total of 164.32 N·m. The muscle force is Fmuscle=164.32/0.05=3,286F_{muscle} = 164.32/0.05 = 3{,}286 N. The supported weight is (15+40)×9.81=539.55(15 + 40) \times 9.81 = 539.55 N, so the rough model gives Fcomp≈3,286+540=3,826F_{comp} \approx 3{,}286 + 540 = 3{,}826 N. A 15 kg load weighing 147 N produces a force on the disc of more than 25 times its weight.

    Example 3: the load close to the body and the back upright. The same load is first pulled to the edge of the machine door with an aid, then lifted with the hands 20 cm from the hip joint and the body upright so that the center of mass of the upper body is 5 cm in front of the joint. The moment of the load is 15×9.81×0.20=29.4315 \times 9.81 \times 0.20 = 29.43 N·m and the moment of the body is 40×9.81×0.05=19.6240 \times 9.81 \times 0.05 = 19.62 N·m, for a total of 49.05 N·m. The muscle force is 49.05/0.05=98149.05/0.05 = 981 N, and Fcomp≈981+540=1,521F_{comp} \approx 981 + 540 = 1{,}521 N. Compared with Example 2, the muscle force drops from 3,286 N to 981 N, or about 70 percent, without reducing the weight of the linen at all.

    Example 4: the recommended weight limit for two positions. 15 kg of linen is lifted from a hand height of 70 cm to a trolley with a travel distance of less than 25 cm. For this exercise the frequency and coupling multipliers are taken as 1.00; the actual values come from the NIOSH tables as in Chapter 21 · Laundry. In the starting position the hands are 50 cm in front of the ankles and the body twists 30°:

    RWL=23×0.50×0.99×1.00×0.90×1.00×1.00=10.25 kg,LI=1510.25=1.46RWL = 23 \times 0.50 \times 0.99 \times 1.00 \times 0.90 \times 1.00 \times 1.00 = 10.25\ \text{kg}, \qquad LI = \frac{15}{10.25} = 1.46

    If the trolley is placed in front of the operator so that the body does not twist and the hands are only 25 cm from the ankles, RWL=23×1.00×0.99=22.77RWL = 23 \times 1.00 \times 0.99 = 22.77 kg and LI=15/22.77=0.66LI = 15/22.77 = 0.66. The lifting index drops from above 1 to below 1 just by changing where the trolley is placed.

    Example 5: energy for short and long work. A piece of muscle work requires 720 units of ATP. Through aerobic respiration at 36 ATP per glucose, 720/36=20720/36 = 20 molecules of glucose are needed; through anaerobic glycolysis at 2 ATP per glucose, 720/2=360720/2 = 360 molecules are needed, 18 times as many, plus the lactic acid that builds up along with it. Heavy work without breaks shifts the muscle to that wasteful pathway, while short breaks give time to pay back the oxygen debt.

    Example 6: repetitive movement at the folding table. A towel folder completes 8 towels per minute, and each towel requires 3 wrist bends. In 7 hours of effective work, the number of bends is 8×3×60×7=10,0808 \times 3 \times 60 \times 7 = 10{,}080. If the task is rotated so that only half the time is spent folding, the number becomes 10,080/2=5,04010{,}080/2 = 5{,}040 per shift. Rotation reduces the repetitions on the same tendons and gives recovery time, but tingling at night as in the opening case is still reported to the company doctor.

    Stop conditions

    Stop the work and hand it over to the supervisor, the K3 officer, the company doctor, or a health professional if:

    1. Back pain comes on suddenly during lifting, or pain radiates into the thigh and leg, or the leg is numb or weak; the worker stops lifting and is examined by a doctor.
    2. The hand tingles, is numb, or has a weak grip, especially at night; the worker reports to the company doctor, and the supervisor reviews the task together with the K3 officer.
    3. The knee, elbow, or shoulder is swollen and painful after kneeling or working with the arms overhead; the worker reports it and does not continue in that position until examined.
    4. The lifting task requires the hands far in front of the body, a twisting body, or loads from inside a drum, from the floor, or from a high shelf without an aid; the task is stopped and reassessed as in Chapter 21 · Laundry and Chapter 3 · Safety, and lifting equipment is used according to Chapter 9 · Safety.
    5. The load is of unknown weight, slippery, or has no handles; the load is weighed first or moved with the help of other people and equipment.
    6. The worker is asked to decide for themselves what load limit is safe for their body, or to take painkillers so they can keep working; that decision belongs to the company doctor.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    A 15 kg load means the back carries 15 kg.

    Why is it wrong?

    The back muscles work with a short moment arm, so the muscle force and the compression of the disc can be tens of times the weight of the load, as in Example 2.

    Common misconception

    As long as you are strong, posture does not matter.

    Why is it wrong?

    Strength does not change the moment; the distance of the load and the posture of the back determine it, and Example 3 lowers the muscle force by about 70 percent without reducing the load.

    Common misconception

    Holding a load still is not tiring because there is no movement.

    Why is it wrong?

    An isometric contraction still uses ATP for the cross-bridges and the calcium pump, so a muscle holding a hose or an iron in the same position still tires.

    Common misconception

    Light movements cannot injure the hands.

    Why is it wrong?

    The tendons in the carpal tunnel slide every time the fingers bend; thousands of repetitions per shift with a bent wrist can inflame the tendons and compress the nerve.

    Common misconception

    A lifting index below 1 means safe for anyone.

    Why is it wrong?

    The NIOSH equation assesses the task, not the person, has not been fully validated, and does not replace occupational health examinations.

    Chapter 33 on nerves and the brain explains the signals that trigger contraction, and Chapter 34 on shift work explains fatigue from the side of the biological clock. Chapter 1 · Mechanical & Mechatronics and Chapter 8 · Physics give the basis for moments of force. Chapter 21 · Laundry on laundry K3 assesses lifting tasks in full, Chapter 9 · Safety covers lifting equipment and trolleys, Chapter 5 · Safety personal protective equipment such as knee pads, and Chapter 7 · Safety hand-arm vibration. Chapter 38 on body temperature discusses the heat from muscle work.

    Exercises and worked solutions

    Try to answer first, then open the worked solution.

    1. How many times more ATP does one molecule of glucose produce through aerobic respiration than through anaerobic glycolysis, and what does this mean for heavy work without breaks?

      Check my answer
      See the worked solution

      Aerobic respiration produces about 36 ATP and glycolysis 2 ATP per glucose, so 36/2=1836/2 = 18 times. Heavy work without breaks forces the muscle to use wasteful glycolysis and builds up lactic acid, so it tires faster.

    2. A technician holds a 2 kg toolbox with the forearm horizontal, 30 cm from the elbow, and the upper arm muscle attaches 5 cm from the elbow. What is the muscle force if the weight of the forearm is neglected?

      Check my answer
      See the worked solution

      The weight of the box is 2×9.81=19.622 \times 9.81 = 19.62 N, so Fmuscle=19.62×30/5=117.72F_{muscle} = 19.62 \times 30/5 = 117.72 N, about 118 N, or 6 times the weight of the box. The ratio of 30 to 5 is the inverse of the mechanical advantage of the elbow as a third-class lever.

    3. A worker bends to lift 10 kg with the hands 40 cm in front of the hip joint; the upper body is 40 kg with its center of mass 25 cm in front of the joint, and the moment arm of the back muscles is 5 cm. What is the force of the back muscles?

      Check my answer
      See the worked solution

      The moment of the load is 10×9.81×0.40=39.2410 \times 9.81 \times 0.40 = 39.24 N·m and the moment of the body is 98.1098.10 N·m, for a total of 137.34 N·m, so Fmuscle=137.34/0.05=2,746.8F_{muscle} = 137.34/0.05 = 2{,}746.8 N, about 2,747 N. More than two thirds of the moment comes from the body itself, so straightening the body is as important as bringing the load closer.

    4. The hands are 40 cm in front of the ankles, the hand height is 70 cm, there is no body twist, the travel distance is under 25 cm, and the frequency and coupling multipliers are taken as 1.00. What are the RWL and the lifting index for a 12 kg load?

      Check my answer
      See the worked solution

      The horizontal multiplier is 25/40=0.62525/40 = 0.625, rounded to 0.63 as in the table, so RWL=23×0.63×0.99=14.35RWL = 23 \times 0.63 \times 0.99 = 14.35 kg and LI=12/14.35=0.84LI = 12/14.35 = 0.84. The value is below 1, but the actual frequency and coupling still have to be read from the NIOSH tables and can lower the RWL.

    5. A sarcomere is 2 µm long at rest. Over what range of lengths is its tension at maximum, and why does reaching deep into the drum with the arm fully extended make the load feel heavier?

      Check my answer
      See the worked solution

      Tension is at maximum at 80 to 120 percent of resting length, that is, 1.6 to 2.4 µm. A fully extended arm makes some muscles work outside that range, so the same force requires more recruitment, on top of the long moment arm of the load.

    6. A housekeeping worker kneels on a bathroom floor for several hours per shift and their knee starts to swell. What structure is being compressed, and what is done?

      Check my answer
      See the worked solution

      What is compressed is the bursa in front of the kneecap, which can become inflamed from excessive and prolonged pressure. The worker reports to the company doctor, and the supervisor provides knee pads or long-handled tools according to Chapter 5 · Safety.

    References

    External sources

    • Anatomy and Physiology 2eopenstax.org
    • Applications Manual for the Revised NIOSH Lifting Equationcdc.gov
    • calculating rwlccohs.gc.ca
    • NIOSH Lifting Equation - Horizontal Distance Multiplier Factorccohs.gc.ca
    • NIOSH Lifting Equation - Vertical Distance Multiplier Factorccohs.gc.ca

    Revision history

    DateVersionChange
    November 10, 20261First published

    How to cite

    Kurnia (2026). Muscles, bones, and joints at work: muscle fibers and contraction, muscle fatigue, the spine and discs, body levers and forces on the back, repetitive injuries to the hands, and working posture. ARSTEMA Academy. Revised November 10, 2026. arstema.com/en/academy/konsep/otot-tulang-dan-sendi-saat-bekerja-serat-otot-dan-kontraksi-kelelahan-otot-tulang-belakang-dan-cakram-tuas-tubuh-dan-gaya-pada-punggung-cedera-berulang-pada-tangan-dan-posisi-kerja

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated
    1

    How many times more ATP does one molecule of glucose produce through aerobic respiration than through anaerobic glycolysis, and what does this mean for heavy work without breaks?

    2

    A technician holds a 2 kg toolbox with the forearm horizontal, 30 cm from the elbow, and the upper arm muscle attaches 5 cm from the elbow. What is the muscle force if the weight of the forearm is neglected?

    3

    A worker bends to lift 10 kg with the hands 40 cm in front of the hip joint; the upper body is 40 kg with its center of mass 25 cm in front of the joint, and the moment arm of the back muscles is 5 cm. What is the force of the back muscles?

    Self-assessment progress0%

    Nearby chapters