By Kurnia · Published November 11, 2026 · Version 1 · 21 min read
Waste in hotels, laundries, and kitchens
types and composition, generation rate and bulk density, source separation, temporary storage areas, reduction and recycling, and calculating container needs
On a Monday morning, a hotel’s temporary waste storage area cannot be closed because weekend reception waste has piled up while the truck only arrives at midday. This chapter covers non-hazardous solid waste from guest rooms, kitchens, restaurants, and laundries: its types and composition, the generation rate per occupied room or per ton of linen, bulk density and how to measure it, source separation, the requirements for containers and temporary storage areas under the annexes of Permenkes 2/2023 and Permenkes 7/2019 (their status as of November 2026 is noted), reduction and recycling with the EPA wasted food scale as a comparison, and the formula for the required container volume and number of containers from the generation rate, emptying interval, bulk density, and fill factor. Data from the United States and England are marked as data from those countries. Hazardous waste, used cooking oil, and medical waste are referred to other chapters.
On a Monday morning at a 160-room hotel, the gardener finds that the waste storage area behind the loading dock cannot be closed. There was a wedding reception on Saturday night, the restaurant was full on Sunday, and the collection truck will not come again until Monday at midday. Bags of food waste are piled outside the containers, leachate is seeping into the stormwater drain, and flies are swarming near the kitchen door. The chief technician is asked a question that looks simple: how many containers are needed, where they should be placed, and how often they must be emptied. The answer depends on three numbers that hotels rarely record: how many kilograms of waste are produced per day, how much volume each kilogram occupies, and how long the waste may wait.
Scope
This chapter covers solid waste that is not hazardous waste (Indonesian limbah B3) from guest rooms, restaurants, kitchens, banquet rooms, offices, gardens, and laundries, plus hospital domestic waste as a comparison. The health requirements for containers and storage areas are taken from the annex of Permenkes 2/2023 (Minister of Health Regulation) on environmental health and the annex of Permenkes 7/2019 on hospital environmental health. As of November 2026, Permenkes 3/2026 revokes both regulations except for a number of articles together with their annexes, while the JDIH Kemenkes pages (the Ministry of Health legal documentation network) mark both as not in force; check their latest status before using them for an audit. The detailed obligations of area managers under UU 18/2008 on Waste Management, PP 81/2012, and regional regulations are not covered here; ask the local environmental agency.
Topics in other chapters: used cooking oil, grease, and used oil in Chapter 34 on used cooking oil and used oil; lamps, batteries, chemical packaging, and other hazardous waste in Chapter 35 on hazardous waste in hotels, laundries, and workshops; medical waste in Chapter 36 on hospital medical waste; wastewater in Chapter 17 · Laundry on laundry wastewater and the IPAL and Chapter 16 on wastewater characteristics; the carbon and nitrogen cycles in Chapter 48 · Biology & Microbiology on biogeochemical cycles; emissions in Chapter 19 · Fluids & Thermal on carbon footprint; pests in Chapter 12 · Biology & Microbiology on pests in kitchens, laundries, and buildings; and portable fire extinguishers (Indonesian alat pemadam api ringan, APAR) in Chapter 17 · Buildings & Facilities on fire protection.
Types and composition of waste
Solid waste is the solid residue of daily human activities and/or natural processes. Waste from hotels, restaurants, and laundries resembles household waste in its types, but the quantity is much larger and the pattern follows occupancy and events.
Each part of the building produces a different mix. Guest rooms produce paper, plastic drinking bottles, cans, leftover room service food, and toiletry packaging. Kitchens produce food preparation scraps (peels, bones, vegetable trimmings), plate waste, cardboard, large cans, glass bottles, and plastic wrapping. Laundries produce plastic wrap from clean linen, clothes hangers, discarded linen, fabric lint from dryer filters, and empty chemical jerry cans. Jerry cans that still contain product or carry a hazard label go into the route of Chapter 35, and dryer lint is a combustible material that needs to be emptied into a closed container.
Waste composition is the division of waste mass by material type, expressed as a mass fraction or percentage:
where is the mass fraction of type (dimensionless), the mass of type in the sample (kg), and the mass of the whole sample (kg). All the add up to 1. Composition is calculated from a sample that has been sorted and weighed, not from a visual estimate, because cardboard and plastic look plentiful but are light, while food waste looks small but is heavy.
As an indication of scale, the EPA recorded United States municipal solid waste in 2018 at 292.4 million tons, or 4.9 pounds per person per day, with paper and paperboard at 23.1 percent, food at 21.6 percent, and plastics at 12.2 percent of total generation. Those are United States national data that mix households, offices, and businesses, so they are not used as the composition of a hotel in Indonesia; a hotel’s composition is measured in that building itself.
Generation rate and bulk density
Waste generation rate is the mass or volume of waste produced per unit of activity per unit of time. The unit of activity chosen is the one that most determines the amount of waste: occupied rooms for a hotel, servings or diners for a restaurant, tons of linen processed for a laundry, and occupied beds for a hospital.
where is the generation rate (kg per unit per day), the mass of waste weighed during the measurement period (kg), the average number of activity units (units), and the length of the measurement (days). When changes every day, the number of unit-days () is used as the denominator. Measurement should cover one full week, including the weekend, because event days and quiet days can differ widely. Days with large events are recorded separately, since the waste from a reception for 400 guests is not proportional to the number of rooms occupied that night. Every bag or container is weighed before being emptied into the storage area, minus the weight of the empty container, and the daily log records the date, waste stream, mass, and number of activity units.
Bulk density of waste (Indonesian berat jenis sampah) is the mass of waste per unit volume of the container it occupies, including the air spaces between items, expressed in kg/m³ or kg/L. In physics, the Indonesian term berat jenis means a different quantity; this chapter follows its use in solid waste engineering.
where is the bulk density (kg/m³), the net mass of waste (kg), and the filled volume of the container (m³). To measure it: an empty container of known volume is weighed, filled with waste without pressing it down until level with the rim, and weighed again. The bulk density of different materials can differ by more than ten times, because whole plastic bottles are almost entirely air, while wet food waste fills the gaps.
The 2016 EPA conversion factor table gives an indication (United States data, original units pounds per cubic yard, converted with 1 lb/yd³ = 0.5933 kg/m³):
| Waste type (EPA) | Original value | Equivalent |
|---|---|---|
| Restaurant food waste | 396 lb/yd³ | about 235 kg/m³ |
| Mixed commercial waste, uncompacted | 138 lb/yd³ | about 82 kg/m³ |
| Old corrugated cardboard, flattened | 106 lb/yd³ | about 63 kg/m³ |
| Glass bottles, loose | 380 lb/yd³ | about 225 kg/m³ |
| Aluminum cans, uncompacted | 46 lb/yd³ | about 27 kg/m³ |
| Mixed PET and HDPE bottles, loose | 32 lb/yd³ | about 19 kg/m³ |
These figures are a starting point for planning. Moisture content, the way waste is thrown away, and compaction change the bulk density, so a hotel should measure it for each stream.
Source separation
Source separation is separating waste by type at the place where it is first thrown away, before it is mixed in a trolley or storage area. Separating at the source is cheaper than re-sorting a mixed pile, because food residue that sticks to paper and plastic makes them unsellable.
For food handling establishments, including hotel restaurants, the annex of Permenkes 2/2023 requires waste bins to be made of strong material, closed, easy to clean, lined with a plastic bag, and not touched by hand to open them; waste is separated into wet (organic) waste and dry (inorganic) waste and emptied routinely at least every 1x24 hours. The same annex requires waste bins to be available in rooms where activities take place or in public spaces and outside the building, for public facilities and buildings.
For hospitals, the annex of Permenkes 7/2019 is more detailed. Organic and inorganic waste are placed in different containers starting in the room where they arise, waste must not be left in its container for more than 1 x 24 hours or once 2/3 of the bag is full, at least one waste bin is provided for each room or as needed, and the separation bins are lined with clear or white bags for recyclable waste. Domestic waste that falls into the hazardous waste category is separated and handled as hazardous waste. The bins are opened with a foot pedal, strong, watertight, and insect-proof.
England provides a useful comparison for hotels. Since March 31, 2025 (for micro-firms, March 31, 2027), workplaces in England, including hotels and restaurants, must separate dry recyclable materials (plastic, metal, glass, paper, and card), food waste, and non-recyclable residual waste before collection. The guidance also names contamination, meaning items placed in the wrong recycling bin or recyclables soiled by food or liquid residue, and calls for clear instructions on or near the bins. Those are English data and rules, not obligations in Indonesia.
A reasonable arrangement for a hotel in Indonesia: organic bins in the kitchen, dishwashing room, and restaurant; inorganic recycling bins in the kitchen, storerooms, offices, and laundry; residual bins at every point; and a dedicated locked container for lamps, batteries, and aerosol cans that are passed on to the route of Chapter 35. Two small bins are enough in guest rooms, and housekeeping staff re-sort at the trolley when needed.
Temporary storage area
A temporary waste storage area (Indonesian tempat penampungan sementara, TPS) is the place where waste from the whole building is collected before it is taken off site. For food handling establishments, the annex of Permenkes 2/2023 requires the TPS to be watertight, easy to clean, and closed, and requires food handling buildings to be located away from pollution sources such as a waste TPS, or to have measures that prevent the impact of contamination.
The annex of Permenkes 7/2019 gives a list of requirements for the hospital domestic solid waste TPS that can serve as a comparison for hotels:
| Aspect | Requirement for a hospital domestic waste TPS |
|---|---|
| Location | service area, away from inpatient care, outpatient care, the emergency department, operating rooms, the nutrition kitchen, the canteen, the laundry, and other important rooms |
| Building | enclosed or semi-open, roof watertight against rain, adequate ventilation and air circulation, adequate lighting, walls and floor strong, watertight, and easy to clean |
| Cleaning and water | cleaned at least once every 1 x 24 hours; a water tap with adequate pressure; a washbasin with soap; a floor with a curb and a drain to an inspection chamber or the IPAL |
| Safety | a name board, a no-entry sign, APAR and a fire alarm, no-burning and no-smoking signs, a security fence at least 2 meters high, a first aid box and PPE |
| Holding time | domestic waste in the TPS must not stay longer than 2 x 24 hours and remains wrapped in bags |
Leachate is the liquid that drains from a waste pile, especially from food waste. The curb and the drain to the inspection chamber keep leachate from flowing into the stormwater drain, because leachate carries a high organic load like kitchen wastewater (Chapter 16 on wastewater characteristics).
The location of the TPS also affects fire safety. The English fire risk assessment guidance for sleeping accommodation asks for wheeled bins outside the building to be secured in a compound so that they cannot be moved next to the building and set on fire, and for skips not to be placed against a building, normally at least 6 meters from any part of the premises. The same guidance asks that waste and laundry not accumulate in escape routes. The 6 meter figure is English guidance; the distance in Indonesia is set together with the building manager and the fire protection officer.
Reduction and recycling
The EPA waste management hierarchy ranks management approaches from most to least environmentally preferred, with an emphasis on reducing, reusing, and recycling. The EPA Wasted Food Scale, an update of the food recovery hierarchy, places prevention, donation, and upcycling into new food as the most preferred pathways, while landfilling, incineration, and sending food down the drain are the least preferred. The EPA estimates that food is 24 percent of the material in United States municipal solid waste landfills and is responsible for 58 percent of landfill methane emissions to the atmosphere, because food waste decays quickly before its gas can be captured.
For a hotel, the largest prevention happens in the kitchen and restaurant: a buffet in small containers that are refilled more often, purchase planning, and recording plate waste. The annex of Permenkes 2/2023 includes waste reduction and management by the 3R principle in the energy efficiency and environmental requirements for facilities and buildings. In guest rooms, refill dispensers replace small toiletry bottles. In the laundry, empty chemical jerry cans that can be returned to the supplier for refilling reduce plastic, provided that the supplier actually accepts returns.
Recycling only works when materials are clean and separated. Cardboard is flattened to reduce its volume, bottles are emptied, and cans contain no food residue. The measure of success is the diversion rate:
where is the diversion rate (dimensionless or percent), the mass of waste sent to recycling, composting, or other use (kg per day), and the mass of all waste generated (kg per day). Waste that was separated but mixed again in the TPS or truck does not count as diverted. For that reason, the diversion rate is calculated from the weighing at handover to the processor, not from the contents of the separation bins in the corridor.
Calculating container needs
The required container volume for one waste stream is calculated from the mass collected during the emptying interval, divided by the bulk density and the fill factor:
where is the required container volume (m³), the generation rate (kg per unit per day), the number of activity units (units), the longest emptying or collection interval (days), the peak factor (dimensionless, the ratio of the busiest day to the average), the bulk density of that stream (kg/m³), and the fill factor (dimensionless). The fill factor is the portion of the container volume that may be filled so that the lid still closes and the bag can still be tied. For bags in hospital rooms, the 2/3 limit from Permenkes 7/2019 can be used directly; for TPS containers, the fill factor is set by the user, for example 0.9.
The number of containers is rounded up:
where is the number of containers and the volume of one container (m³). This formula is applied per stream: food waste is heavy and decays quickly, so its containers are small and emptied often, while cardboard and bottles are light but take up space.
There are two other limits outside the formula. The first limit is time: the formula gives the volume for interval , but if exceeds the holding limit (1x24 hours for bins in food handling establishments, 2 x 24 hours for a hospital domestic waste TPS), what has to change is the collection schedule, not the number of containers. The second limit is weight: bags and bins that are too heavy cannot be lifted safely by one person, so food waste containers are chosen small or on wheels (Chapter 40 · Biology & Microbiology on muscles, bones, and joints at work).
Worked example
The numbers in the examples below are practice numbers, unless their origin is stated.
Example 1: generation rate per occupied room. For one week, the hotel in the opening case weighed all its waste: 412, 386, 398, 437, 518, 624, and 571 kg, with 120, 112, 115, 124, 142, 156, and 148 occupied rooms. The total mass is 3,346 kg and the total is 917 occupied room-days, so kg per occupied room per day. The daily average is kg, and the Saturday peak factor is . Because there was a reception on Saturday, part of that day’s waste came from party guests, so the following week the hotel recorded event waste as a separate line.
Example 2: composition from a sorted sample. A 120 kg sample is sorted into food waste 61.2 kg, paper and cardboard 19.2 kg, plastic 14.4 kg, glass 8.4 kg, metal 3.6 kg, textiles 2.4 kg, and other residue 10.8 kg. The organic fraction is . The recyclable materials (paper, plastic, glass, metal) total 45.6 kg, that is, , and the residual (textiles and residue) is 13.2 kg or 0.11. With an average of 478 kg per day, the daily streams are roughly organic kg, recyclable kg, and residual kg.
Example 3: bulk density from the table and from the scale. The EPA value for restaurant food waste, 396 lb/yd³, is equivalent to kg/m³. At the hotel, an empty 120 L bin is weighed at 9.5 kg, then filled with kitchen scraps without pressing them down to the rim of the bin and weighed at 37.0 kg. The net mass is 27.5 kg, so kg/m³, close to the EPA value. In contrast, loose plastic bottles at 19 kg/m³ give only kg per 120 L bin, so the same bin becomes full with a mass twelve times smaller.
Example 4: food waste bins in the kitchen. The main kitchen produces 210 kg of food waste per day. The bins are emptied into the TPS at every shift change, so days. With kg/m³ and a fill factor of 2/3, m³, that is, 685 L. With 120 L bins, bins. Each bin filled to 2/3 holds kg, which can still be lifted; a 240 L bin filled the same way would hold 36.8 kg and needs to be pushed on wheels.
Example 5: TPS containers with collection three times a week. The truck comes on Monday, Wednesday, and Friday, so the longest interval, Friday to Monday, is days. With , a fill factor of 0.9, and 660 L containers: organic m³, that is, 7 containers; recyclables with kg/m³ give m³, that is, 14 containers; residual with kg/m³ gives m³, that is, 5 containers. The total is 26 containers. This calculation also shows two schedule problems: food waste waits three days in the TPS, longer than the 2 x 24 hour limit that applies to a hospital domestic waste TPS, and the light recyclable stream takes the most containers. The fix is daily collection of organics and flattening of cardboard, not more containers.
Example 6: the effect of reduction and separation. The hotel reduces food waste by 15 percent through changes to the buffet, so the organic stream becomes kg per day. 90 percent of the organics and 75 percent of the recyclables are successfully separated and handed over to processors, that is, kg and kg. The new generation is kg per day, and the diversion rate is . The residual waste still sent to the landfill falls from about 479 kg to kg per day.
Stop conditions
- A domestic waste bag from a guest room, toilet, or ward turns out to contain needles, razors, syringes, or bloody waste: do not sort it by hand and do not squeeze the bag; set that bag apart, mark it, and hand it over to the person responsible for medical waste or the occupational safety and health (K3) officer (Chapter 36 on hospital medical waste and Chapter 11 · Biology & Microbiology on standard precautions).
- Lamps, batteries, aerosol cans, or jerry cans with a hazard label are found in an ordinary waste bin: remove them from the domestic waste stream while wearing gloves and hand them over to the person responsible for hazardous waste (Chapter 35 on hazardous waste in hotels, laundries, and workshops).
- Smoke, a burning smell, or heat is coming from a bin, a TPS container, or a pile of dryer lint and cleaning cloths: do not open the lid wide and do not break up the pile; keep people away, sound the alarm, and hand over to the emergency response team and the fire department (Chapter 17 · Buildings & Facilities on fire protection).
- Waste overflows until it blocks an escape route or emergency door, or rests against a building wall: stop piling waste in that place and report to the chief technician or the housekeeping manager for an extra collection.
- Leachate is flowing from the TPS into the stormwater drain, or the TPS curb is damaged: stop rinsing into that drain and report to the chief technician; repairs to the drain and inspection chamber are done by building technicians or a contractor.
- Rats are seen during the day at the TPS, or flies and cockroaches exceed the monitoring limits: hand over to a licensed pest control operator (Chapter 12 · Biology & Microbiology on pests in kitchens, laundries, and buildings).
- The trash compactor has jammed, its safety door is damaged, or someone has been asked to put a hand into the compression chamber: stop the machine, do not reach inside, and hand over to an authorized technician using lockout and tagout (Chapter 76 · Electrical & Control on safe work).
- A bag or bin is too heavy for one person to lift safely: do not force the lift; split the load or use a trolley and a lifting aid, and report to the supervisor if the container size needs to change (Chapter 40 · Biology & Microbiology on muscles, bones, and joints at work).
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
The bulk density of waste is the same as the density of its material.
Why is it wrong?
The bulk density of waste includes the air spaces between items. Solid plastic has a density tens of times greater than loose plastic bottles in a bin, so containers are calculated from the bulk density measured in the container.
Common misconception
The generation rate only needs to be measured on one ordinary working day.
Why is it wrong?
Event days, weekends, and holiday seasons can raise waste far above the average. Measurement covers at least one full week, and large events are recorded separately.
Common misconception
A container filled until it overflows is being used efficiently.
Why is it wrong?
An overflowing container cannot be closed and its bag cannot be tied, so flies and odor escape. The fill factor, for example 2/3 for bags in hospital rooms, is part of the calculation.
Common misconception
If the truck comes less often, just add containers.
Why is it wrong?
Adding containers solves the volume but not the holding time. Food waste that waits three days in tropical air rots, and hospitals are limited to 2 x 24 hours in the TPS.
Common misconception
All plastic and paper may go into the recycling bin.
Why is it wrong?
Paper and plastic soiled by food or liquid residue are contamination and can cause a whole load to be rejected by the processor. Instructions on the bins and checking bin contents reduce contamination.
Links to other chapters
Used frying oil and grease from the kitchen, which are often thrown away with food waste, are covered in Chapter 34 on used cooking oil and used oil. Hazardous waste found in the waste stream is handled according to Chapter 35 on hazardous waste in hotels, laundries, and workshops, and medical waste according to Chapter 36 on hospital medical waste. Leachate and TPS rinse water go into the wastewater system in Chapter 17 · Laundry on laundry wastewater and the IPAL. Methane from food waste in landfills and its emission values are covered in Chapter 48 · Biology & Microbiology on biogeochemical cycles and Chapter 19 · Fluids & Thermal on carbon footprint.
Exercises and worked solutions
Try to answer first, then open the worked solution.
A hotel laundry processes 9.2 tons of linen in five days and weighs 46 kg of solid waste (plastic wrap, hangers, dryer lint). What is its generation rate per ton of linen?
Check my answer
See the worked solution
The generation rate is kg per ton of linen. The unit per ton of linen is chosen because laundry waste follows the amount of linen processed, not the number of occupied rooms, so this figure can be compared from month to month even when occupancy changes.
A 240 L bin holds flattened cardboard with a net mass of 15 kg. What is its bulk density, and is it close to the EPA value?
Check my answer
See the worked solution
Its bulk density is kg/m³. That value is close to the 106 lb/yd³, or about 63 kg/m³, in the EPA table for flattened cardboard, so the bin is filled normally and flattening is already being done.
Why must food waste not go into the dry recycling bin, even in small amounts?
Check my answer
See the worked solution
Food waste and liquids soil the paper, cardboard, and plastic in the same bin, so those materials become contamination and can be rejected by the processor. As a result, a load that should have been diverted can end up as residual waste, and the diversion rate falls.
A hotel restaurant produces 90 kg of food waste per day, the bins are emptied once a day, the bulk density is 230 kg/m³, and the fill factor is 2/3. How many 120 L bins are needed?
Check my answer
See the worked solution
m³ or 587 L, so bins. The fifth bin is needed because four bins give only 480 L, and the rest would overflow or force the bags to be filled beyond 2/3.
The domestic waste TPS of a hospital is collected three times a week. What is wrong, and what is changed?
Check my answer
See the worked solution
The longest interval with collection three times a week is three days, longer than the 2 x 24 hour limit for domestic waste in a hospital TPS under the annex of Permenkes 7/2019. What is changed is the collection schedule, for example every day or at most every two days, not the number of containers.
A hotel installs a trash compactor that raises the bulk density of residual waste from 82 to 250 kg/m³. In Example 5, how many 660 L containers are needed for residual waste, and what does not change?
Check my answer
See the worked solution
With kg/m³, m³, so 2 containers of 660 L, down from 5. The mass collected and the holding time of the waste in the TPS do not change, so the compactor replaces neither separation nor the collection schedule.
References
External sources
- Peraturan Menteri Kesehatan Nomor 2 Tahun 2023 tentang Peraturan Pelaksanaan Peraturan Pemerintah Nomor 66 Tahun 2014 tentang Kesehatan Lingkunganjdih.kemkes.go.id
- Peraturan Menteri Kesehatan Nomor 7 Tahun 2019 tentang Kesehatan Lingkungan Rumah Sakitjdih.kemkes.go.id
- Peraturan Menteri Kesehatan Nomor 3 Tahun 2026 tentang Penanggulangan Penyakitjdih.kemkes.go.id
- Volume-to-Weight Conversion Factorsepa.gov
- National Overview: Facts and Figures on Materials, Wastes and Recyclingepa.gov
- Wasted Food Scaleepa.gov
- Simpler recycling: workplace recycling in Englandgov.uk
- Fire safety risk assessment: sleeping accommodation (accessible)gov.uk
Revision history
| Date | Version | Change |
|---|---|---|
| November 11, 2026 | 1 | First published |
How to cite
Kurnia (2026). Waste in hotels, laundries, and kitchens: types and composition, generation rate and bulk density, source separation, temporary storage areas, reduction and recycling, and calculating container needs. ARSTEMA Academy. Revised November 11, 2026. arstema.com/en/academy/konsep/sampah-di-hotel-laundry-dan-dapur-jenis-dan-komposisi-timbulan-dan-berat-jenis-pemilahan-di-sumber-tempat-penampungan-sementara-pengurangan-dan-daur-ulang-serta-menghitung-kebutuhan-wadah
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
A hotel laundry processes 9.2 tons of linen in five days and weighs 46 kg of solid waste (plastic wrap, hangers, dryer lint). What is its generation rate per ton of linen?
A 240 L bin holds flattened cardboard with a net mass of 15 kg. What is its bulk density, and is it close to the EPA value?
Why must food waste not go into the dry recycling bin, even in small amounts?
Nearby chapters
Reading order by shelf: Water & Water Treatment · Chapter 34.
Reading order by shelf: Water & Water Treatment · Chapter 32.
Another chapter in Water & Water Treatment.