Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Water & Water Treatment · Chapter 39Applied

    By Kurnia · Published November 14, 2026 · Version 1 · 21 min read

    Wastewater pumps and building sumps

    submersible pumps, floats and alarms, check valves, odor and gas in the sump, cleaning, and the limits of confined space entry

    The high-level alarm of a wastewater sump in the basement of a hospital has been silenced with tape, its standby pump runs but the water level does not fall, the pump room smells of rotten eggs, and a staff member proposes climbing down into the sump to lift out the jammed pump. This chapter covers wastewater sumps and submersible pumps from the building technician’s side: the arrangement of the sump, pumps, guide rails, discharge pipe, and level settings, calculating working volume, fill time, pump-down time, cycle time, starts per hour, and the reserve volume above the alarm, floats, alarms, and standby pumps that must not be bypassed, leaking check valves, hydrogen sulfide and oxygen deficiency with the limit values of Permenaker 5/2018, Permenaker 11/2023, NIOSH, and HSE, the electrical hazard of submersible pumps, infection from wastewater, and the limits of confined space entry. Electrical work on the pumps and panel, lifting a pump before its circuit is isolated, and any entry into the sump or pump pit are the work of authorized electricians and licensed confined space K3 personnel holding an entry permit.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    At two in the morning, a hospital security officer reports that the floor of the basement pump room is wet and smells of rotten eggs. Wastewater from the diet kitchen, the linen laundry room, and the basement toilets flows into a sump in that room, and two submersible pumps push it to the city sewer. The technician on duty finds the high-level alarm lamp on the panel lit, but its siren has been silenced with tape because it “keeps going off by itself.” Pump 1 has tripped, while pump 2 is running, yet the water level barely falls, and every time the pump stops, water can be heard flowing back down the discharge pipe. A staff member proposes climbing briefly down into the 2.2 m deep sump, which holds rotting wastewater and two live cables, to lift out pump 1. What is needed instead is reading the panel from outside, calculating how long the sump can still hold, and knowing when to hand the work over.

    Scope

    This chapter covers building wastewater sumps emptied by submersible pumps in hotels, laundries, kitchens, and hospitals, from the building technician’s side: the arrangement of the sump and pumps, volume and cycle time, floats and alarms, check valves, gas in the sump, electrical and infection hazards, cleaning, and the limits of confined space entry. The Indonesian regulations used are Permenaker (Minister of Manpower Regulation) 11/2023 on K3 (occupational safety and health) in confined spaces and Permenaker 5/2018 on K3 of the work environment. As of November 2026, JDIH Kemnaker lists both as in force; Permenaker 11/2026 revokes several provisions about inspectors in them, but not the definitions, the entry permit obligation, and the annex of threshold limit values used here. The figures of the UK HSE and of the United States EPA and NIOSH are written as figures of those countries.

    The properties of wastewater are in Chapter 16 on wastewater characteristics and Chapter 17 · Laundry on laundry wastewater and the IPAL, drain odors in Chapter 6 · Buildings & Facilities on drainage, traps, and vents and Chapter 15 · Buildings & Facilities on plumbing maintenance, pump curves in Chapter 9 · Buildings & Facilities on building water pumps, pump alternation in Chapter 54 · Electrical & Control on advanced control circuits, floats in Chapter 58 · Electrical & Control on process switches, and check valves in Chapter 12 · Buildings & Facilities on valves. Atmospheric testing, entry permits, and rescue are in Chapter 11 · Safety on confined spaces, and the origin of hydrogen sulfide in Chapter 17 · Biology & Microbiology on microbial metabolism and gases.

    Electrical work on the pumps, cables, floats, and panel, lifting a pump before its circuit is isolated, any activity that puts part of the body into the sump or pump pit, and sludge removal belong to authorized electricians, licensed confined space K3 personnel holding an entry permit, and licensed contractors. The building technician reads the panel and the level from outside, keeps records, tests the alarm according to the procedure, and reports.

    Arrangement of the sump and submersible pump

    A wastewater sump is a pit below the level of the building drain that collects wastewater from fixtures too low to flow by gravity to the city sewer, and is then emptied by a pump. A submersible pump is a pump whose motor is built into the pump housing and works submerged in the sump. The water leaves through a discharge pipe, which rises from the sump and then joins a gravity drain at a higher point.

    A good arrangement lets the pump be serviced without anyone going in. The grinder pump figure in the EPA fact sheet on pressure sewers shows guide rails and a lifting chain, start and stop level controls, a separate high-water alarm control, a panel with a visual alarm, and a shutoff valve. Building sumps also have a check valve and an isolation valve, a vent pipe, a lockable cover, and often a standby pump.

    The water level moves between settings fixed by the designer, from the bottom up: the stop level, where the pump stops with residual water that keeps the pump submerged; the start level, where the duty pump starts; the second pump start level, if there is one; the high-level alarm; and the overflow level, when the water reaches the lowest inlet and spills onto the floor or back into upstream fixtures. The volume between the stop and start levels is called the working volume, and the volume between the alarm and overflow levels is called the reserve volume.

    Sump volume, flow, and pump cycle time

    The volume between two level settings is calculated from the sump area and their height difference:

    V=A ΔhV = A\,\Delta h

    where VV is the volume (m³), AA the cross-sectional area of the sump (m²), and Δh\Delta h the height difference between levels (m). This formula is for a sump with vertical walls; the pipes and pumps inside make the real volume slightly smaller.

    With inflow QiQ_i and pump flow QpQ_p, one cycle consists of a fill time and a pump-down time:

    ti=VQi,tk=VQp−Qi,T=ti+tkt_i = \frac{V}{Q_i}, \qquad t_k = \frac{V}{Q_p - Q_i}, \qquad T = t_i + t_k

    where tit_i is the fill time from the stop level to the start level (s), tkt_k the pump-down time while water keeps flowing in (s), TT the time of one cycle (s), and the flows are in m³/s. The pump flow is taken as constant and Qi<QpQ_i < Q_p; if Qi≥QpQ_i \geq Q_p, the water level keeps rising to the alarm. The number of starts per hour is 3,600/T3{,}600/T.

    Chapter 54 · Electrical & Control derives that the shortest cycle occurs when the inflow is half the pump flow, Tmin=4V/QpT_{min} = 4V/Q_p, and the maximum number of starts of one pump, 3,600/Tmin3{,}600/T_{min}, is compared with the limit from the pump and motor manufacturer. Narrowing the level band so the sump is “drier” increases the starts and heats the motor (Example 2), so the level settings are fixed by the designer.

    If all pumps fail, the time from alarm to overflow is tc=Vc/Qit_c = V_c/Q_i, where VcV_c is the reserve volume. For small systems outside buildings, the EPA fact sheet on low pressure pipe systems states that the pumping chamber is usually sized to provide excess storage of at least one day’s flow above the alarm float, in case of a power failure or pump malfunction. That is a figure for residential systems in the United States; a building sump that receives tens of cubic meters per day relies on standby pumps, a generator set, and a fast response to the alarm (Example 3).

    Floats, high-level alarm, and standby pump

    A float switch is a switch whose contacts change over when its float is lifted or left hanging by the water level (Chapter 58 · Electrical & Control). In a wastewater sump a float can snag on rags, grease, or the pump cable. That is why the high-level alarm uses its own separate sensor, as in the EPA figure above.

    EPA advises a visible and audible alarm when the water rises to the alarm level during a power failure or pump malfunction, the alarm located at the panel so it is easy to test, and an elapsed run-time meter and pump start counter installed in the panel for troubleshooting. Another EPA fact sheet states that power outages can result in overflows if standby generators are not available. For a building sump, the wastewater pumps are a generator set load, as in Chapter 36 · Electrical & Control on generator sets, transfer switches, and standby supply.

    An alarm that goes off often is a symptom: a snagged float, drifted settings, a worn pump, a leaking check valve, or inflow above the design. The cause is found, while the siren is not silenced, the float is not wedged, and the contacts are not jumpered. The alarm is tested from outside the sump according to the designer’s or manufacturer’s procedure, for example the panel test button for the lamp and siren, and a level function test by the designated person in the way written in the procedure. The test is not done by jumpering contacts, lifting the float by hand, or putting tools into the sump without a permit and isolation.

    Check valve and discharge pipe

    A check valve in the discharge pipe holds the water in the pipe so it does not return to the sump when the pump stops (Chapter 12 · Buildings & Facilities). In a wastewater pipe, its disc can be held open by rags or grease, or its seat can wear.

    A leaking valve can be recognized from outside: every time the pump stops, the contents of the discharge pipe can be heard flowing back, the water level rises with no new inflow, and the pump pumps the same water over and over (Example 4). When two pumps share a pipe, the check valve of the idle pump also stops water from the running pump from returning to the sump through the idle pump. That is the opening case: pump 2 is turning, but part of its water returns through the check valve of pump 1, which is stuck open.

    Opening or repairing a check valve means opening a pipe that holds wastewater under static pressure, so it is done by the designated person after the pump is isolated, the isolation valve is closed, and the pressure is released, under the work permit in Chapter 76 · Electrical & Control on safe work, LOTO, and work permits and Chapter 4 · Safety on non-electrical energy isolation.

    Odor and gas in the sump: hydrogen sulfide and oxygen deficiency

    Wastewater that stands for a long time loses its dissolved oxygen, and then sulfate-reducing bacteria produce hydrogen sulfide (Chapter 17 · Biology & Microbiology). The EPA fact sheet on pressure sewers states that the wastewater in such systems can be assumed to be anaerobic and potentially odorous if turbulence strips gases such as hydrogen sulfide, and that personnel need to avoid exposure to that toxic gas in sewer lines, pump vaults, or septic tanks. Building sump water that stands overnight and is then stirred by the pump and by water falling from the inlet pipe releases gas in the same way.

    Hydrogen sulfide is a colorless gas that smells of rotten eggs. NIOSH notes that the sense of smell becomes rapidly fatigued and cannot be relied on to warn of its presence, that its density relative to air is 1.19 so the gas tends to collect in low places, and that it is flammable with a lower explosive limit of 4.0 percent by volume. A foul smell is therefore a signal to move away and report, and the loss of the smell does not prove that the gas is gone.

    ProvisionValue for hydrogen sulfide
    Permenaker 5/2018 (Indonesia)NAB 1 bds (ppm); PSD 5 bds
    EH40/2005 (United Kingdom)long-term 5 ppm (8-hour average); short-term 10 ppm (15 minutes)
    NIOSH and OSHA (United States)NIOSH ceiling 10 ppm (10 minutes); OSHA ceiling 20 ppm with a 50 ppm peak (10 minutes); IDLH 100 ppm

    The threshold limit value (NAB, nilai ambang batas) under Permenaker 5/2018 is the time-weighted average concentration that a worker can be exposed to without disease or health effects, for no more than 8 hours a day or 40 hours a week. The permitted short-term exposure (PSD, paparan singkat diperkenankan) is the concentration that must not be exceeded during an exposure of no more than 15 minutes, no more than 4 times in one working day. The Indonesian NAB is stricter than the UK and United States figures, and it is the one that applies here. NIOSH notes that 1 ppm of hydrogen sulfide equals 1.40 mg/m³.

    The second hazard is oxygen deficiency, which has no smell. Permenaker 11/2023 defines a hazardous atmosphere in a confined space as oxygen below 19.5 percent or above 23.5 percent of the air volume, flammable substances above 10 percent of the lower explosive limit, or toxic substances above the threshold limit value. HSE notes that normal oxygen in air is 20.9 percent, that even a small reduction can impair mental ability without warning, and that levels below 16 percent can lead to unconsciousness and death, even when only the person’s head is inside the confined space.

    Odor can also come from a dry trap or a blocked vent (Chapter 6 · Buildings & Facilities and Chapter 15 · Buildings & Facilities). The building technician reads and records the fixed gas detector; measurements inside the sump are made by the gas detection technician.

    Electric shock from submersible pumps

    A submersible pump places its motor and cable in conductive wastewater. HSE writes that the risk of electrical injury is greatest in wet surroundings, because unsuitable equipment can easily become live and can make its surroundings live. A stripped cable or a leaking motor seal can make the water and the lifting chain live.

    HSE also writes that RCDs for protecting people have a rated tripping current of not more than 30 mA, must never be bypassed, and when they trip it is a sign of a fault, so the system is checked before it is used again. A pump RCD that trips while the sump is close to overflowing is not reset repeatedly; the right step is to call an authorized electrician, while the standby pump, the reserve volume, and reduced upstream flow, for example delaying the draining of washing machines, are used to buy time. For work inside a confined space, Permenaker 11/2023 requires a power supply of no more than 50 volts for dry conditions and no more than 25 volts for damp conditions.

    Three habits apply to the building technician. The pump is not lifted, jiggled, or touched before an authorized electrician has isolated, locked, and proven its circuit dead (Chapter 76 · Electrical & Control). The power cable is not a lifting rope; the pump is lifted by the chain and guide rails from above, and a sump without rails or a chain is reported as a design defect. Cables, junction boxes, and the panel are inspected from outside without opening anything, and the findings are reported.

    Cleaning, infection, and the limits of confined space entry

    Wastewater carries disease-causing microbes. HSE writes that most work-related illness from sewage is mild gastroenteritis, but potentially fatal diseases such as leptospirosis (Weil’s disease, transmitted by rat urine) and hepatitis are also reported. Microbes enter through hand-to-mouth contact, cuts, the eyes, the nose, and inhaled aerosol. HSE advises waterproof gloves and footwear, eye, respiratory, and face protection against splashes, washing facilities with soap, and waterproof dressings for wounds. Other precautions are in Chapter 11 · Biology & Microbiology on standard precautions for technicians.

    Cleaning is planned so that nobody goes in. The UK confined space regulations, as explained by HSE, state that no person at work shall enter a confined space to carry out work unless that purpose cannot reasonably be achieved without entry, and HSE gives sumps as an example of a space that can count as a confined space. Sludge is pumped out from above by a licensed vacuum truck, the pump is lifted by its chain after isolation, and a camera is used to look at the sump floor. Because sludge disturbed during cleaning can release toxic gas, vacuuming is done with the pump room ventilated and other people kept away.

    Permenaker 11/2023 includes wells or pits open at the top with a depth of more than 1.5 m in confined spaces, and treats a worker as entering a confined space when part or all of their body is inside. A space that contains a hazardous atmosphere or material that can engulf a person is a permit-required confined space; work cannot be done before the area person in charge issues an entry permit after a K3 expert has checked gas testing, air flow, energy lockout, communication, voltage, PPE, and rescue. Personnel who enter, measure gas, and carry out rescue must hold a competency certificate and a K3 license. The sump in the opening case is a permit-required confined space (Chapter 11 · Safety).

    HSE notes that multiple fatalities have occurred when rescuers were overcome by the same conditions as the people they tried to rescue. A person who is untrained and has no breathing protection does not climb down to help; they call for help and for the confined space rescue team.

    Records and division of work

    The sump record contains the date, the run hours and starts of each pump, pump current, alarms and their causes, alarm tests, gas detector readings, backflow, sludge removal, and actions. Starts per hour that rise with no increase in inflow point to a leaking check valve or drifted settings; run hours that rise with the same number of starts point to a worn pump or a clogged impeller (Chapter 12 · Fluids & Thermal on pumps in operation).

    The division of work follows the Scope; the designer fixes the levels, and management decides on repairs.

    Worked example

    The numbers in the examples below are practice numbers unless their origin is stated.

    Example 1: working volume and cycle time. A sump of 1.5 m by 1.2 m has an area A=1.5×1.2=1.8A = 1.5 \times 1.2 = 1.8 m², with the start level 0.40 m above the stop level, so V=1.8×0.40=0.72V = 1.8 \times 0.40 = 0.72 m³, that is, 720 L. At busy hours the inflow is 1.2 L/s and the pump delivers 4.0 L/s. The fill time is ti=720/1.2=600t_i = 720/1.2 = 600 s, the pump-down time tk=720/(4.0−1.2)=257.1t_k = 720/(4.0 - 1.2) = 257.1 s, and one cycle T=600+257.1=857.1T = 600 + 257.1 = 857.1 s, giving 3,600/857.1=4.23{,}600/857.1 = 4.2 starts per hour.

    Example 2: a narrowed level band. The shortest cycle of one pump in the sump of Example 1 is Tmin=4×0.72/0.004=720T_{min} = 4 \times 0.72/0.004 = 720 s, that is, 3,600/720=53{,}600/720 = 5 starts per hour, or 2.5 per pump when they alternate. A staff member narrows the level band to 0.20 m, so V=1.8×0.20=0.36V = 1.8 \times 0.20 = 0.36 m³, Tmin=4×0.36/0.004=360T_{min} = 4 \times 0.36/0.004 = 360 s, and the maximum is 3,600/360=103{,}600/360 = 10 starts per hour. If the manufacturer allows 6 starts per hour, the new setting exceeds the limit when one pump runs alone, so the setting is restored.

    Example 3: time before overflow. An overflow level 0.35 m above the alarm level gives a reserve volume Vc=1.8×0.35=0.63V_c = 1.8 \times 0.35 = 0.63 m³. If both pumps fail at busy hours, tc=630/1.2=525t_c = 630/1.2 = 525 s, less than 9 minutes; at night with an inflow of 0.2 L/s, tc=630/0.2=3,150t_c = 630/0.2 = 3{,}150 s, about 52.5 minutes. This building discharges 40 m³ per day, so one day of storage like the small systems in the EPA fact sheet would be about 40/0.63=6340/0.63 = 63 times the reserve volume available.

    Example 4: backflow from a leaking check valve. A discharge pipe with an inside diameter of 80 mm rises 6 m and then runs horizontally for 10 m. It holds π/4×0.082×16=0.0804\pi/4 \times 0.08^2 \times 16 = 0.0804 m³, about 80 L. If the check valve does not close and the whole pipe contents can drain, that water returns to the sump every time the pump stops and raises the water level by 0.0804/1.8=0.0450.0804/1.8 = 0.045 m with no new inflow. The pump re-pumps 80/720=0.1180/720 = 0.11, that is, 11 percent of the working volume every cycle.

    Example 5: reading a fixed gas detector. The detector in the pump room records hydrogen sulfide at 6 ppm for 2 hours and 0.5 ppm for 6 hours. The 8-hour time-weighted average is (2×6+6×0.5)/8=1.875(2 \times 6 + 6 \times 0.5)/8 = 1.875 ppm, about 1.9 ppm, above the NAB of 1 ppm, and the 6 ppm reading, equal to 6×1.40=8.46 \times 1.40 = 8.4 mg/m³, is above the PSD of 5 ppm. The technician does not open the sump cover and reports to the person in charge of K3.

    Example 6: water standing over the weekend. The water below the stop level has a volume of 1.8×0.30=0.541.8 \times 0.30 = 0.54 m³. On an ordinary night, an inflow of 0.2 L/s fills the working volume in 720/0.2=3,600720/0.2 = 3{,}600 s, that is, 1 hour. On Sunday, when the diet kitchen and the laundry room are closed and the inflow is 0.05 L/s, the average residence time of all the water is (540+720)/0.05=25,200(540 + 720)/0.05 = 25{,}200 s, that is, 7 hours. Water that stands for hours loses its oxygen, so gas readings can be high when the pumps start running often again.

    Stop conditions

    1. The high-level alarm sounds or the water level keeps rising although a pump is running: do not silence the siren or wedge the float; reduce upstream flow if safe and call an authorized electrician and the person in charge of the building.
    2. The job involves lifting, jiggling, or cleaning the pump while its circuit has not been isolated, locked, and proven dead: do not touch the pump, chain, or cable; wait for isolation by an authorized electrician.
    3. The pump RCD or motor protection trips repeatedly, a cable is scraped or a junction box is open, or someone feels tingling near the sump: do not reset the circuit and do not bypass the protection; hand over to an authorized electrician.
    4. Someone is about to put their head, hand, or body into a sump or pump pit deeper than 1.5 m or holding rotting wastewater: stop until a confined space entry permit has been issued and licensed confined space K3 personnel are available.
    5. A strong smell of rotten eggs is present in the pump room, or the fixed gas detector alarms: leave the room, do not open the sump cover, keep others out, and report to the person in charge of K3.
    6. Someone has fallen or collapsed inside or at the mouth of the sump: do not climb down to help without training and breathing protection; call the confined space rescue team and emergency services.
    7. The work requires opening, removing, or replacing the check valve or isolation valve of the discharge pipe: postpone until the pump is isolated, the pressure is released, and a work permit is issued, then hand over to the designated person.
    8. Wastewater has overflowed onto the floor: cordon off the area, stop upstream fixtures, and hand cleaning and disinfection over to staff wearing PPE.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    An alarm that goes off often can be silenced.

    Why is it wrong?

    An alarm that goes off often points to a snagged float, drifted settings, a worn pump, or a leaking check valve. The cause is found, and the alarm stays live.

    Common misconception

    There is a standby pump, so the alarm is not that important.

    Why is it wrong?

    A standby pump can fail or pump back through a leaking check valve, as in the opening case. The alarm is the last signal before the reserve volume runs out.

    Common misconception

    The sump is safer with the start level as low as possible.

    Why is it wrong?

    A narrow level band increases the starts per hour and heats the motor. The level settings are fixed by the designer and compared with the manufacturer’s start limit.

    Common misconception

    The pump is lifted by its chain from above, so the power does not need to be cut.

    Why is it wrong?

    The chain and the water around the pump can be live if the cable or motor leaks. The pump is lifted after its circuit has been isolated and proven dead by an authorized electrician.

    Common misconception

    I am only looking into the sump opening, not entering.

    Why is it wrong?

    Permenaker 11/2023 treats part of the body inside a confined space as entering the confined space, and HSE notes the danger of low oxygen even when only the head is inside.

    Wastewater treatment after the sump is in Chapter 19 on attached growth and small IPALs. Pump curves are in Chapter 9 · Buildings & Facilities, pump alternation in Chapter 54 · Electrical & Control, floats in Chapter 58 · Electrical & Control, and check valves in Chapter 12 · Buildings & Facilities. Gas and confined spaces are in Chapter 11 · Chemistry on hazardous gases, Chapter 17 · Biology & Microbiology, and Chapter 11 · Safety, while RCDs are in Chapter 22 · Electrical & Control on RCDs and generator sets in Chapter 36 · Electrical & Control.

    Exercises and worked solutions

    The numbers in the exercises are for practice.

    Try to answer first, then open the worked solution.

    1. A sump of 2.0 m by 1.5 m with a 0.30 m level band is emptied by a 5 L/s pump, and the manufacturer allows 6 starts per hour. Calculate the working volume, the shortest cycle, and the maximum starts of one pump.

      Check my answer
      See the worked solution

      The working volume is 2.0×1.5×0.30=0.92.0 \times 1.5 \times 0.30 = 0.9 m³, and the shortest cycle 4×0.9/0.005=7204 \times 0.9/0.005 = 720 s, so one pump makes at most 3,600/720=53{,}600/720 = 5 starts per hour. That is below the limit of 6 starts per hour even when one pump runs alone, and with alternation each pump makes only 2.5 starts per hour.

    2. The alarm siren sounds three times a week, but every time it is checked the water level has already fallen, so a staff member proposes tying the alarm float higher. What is the technician’s answer?

      Check my answer
      See the worked solution

      An alarm that sounds after which the water level falls points to a pump that starts late, for example a snagged control float or a leaking check valve, or a momentary inflow above the design. Tying the alarm float higher shrinks the reserve volume and bypasses a safeguard, so the technician refuses, records the time of each alarm, and asks for the cause to be checked by an authorized electrician and the designer.

    3. The reserve volume above the alarm is 0.5 m³ and the busy-hour inflow is 1.5 L/s. How long until overflow if both pumps fail, and what does this mean for the alarm response?

      Check my answer
      See the worked solution

      The time is 500/1.5=333500/1.5 = 333 s, about 5.6 minutes. Such a short time requires an alarm connected to a place that is staffed at all times, a standby pump and generator set that are ready, and duty staff who know how to reduce upstream flow.

    4. A fixed gas detector records hydrogen sulfide at 4 ppm for 3 hours and 0 ppm for 5 hours. Compare this with the NAB and PSD of Permenaker 5/2018.

      Check my answer
      See the worked solution

      The 8-hour time-weighted average is (3×4+5×0)/8=1.5(3 \times 4 + 5 \times 0)/8 = 1.5 ppm, above the NAB of 1 ppm, while the 4 ppm peak is still below the PSD of 5 ppm. The average exposure still exceeds the limit, so the finding is reported for an official measurement and for ventilation improvements.

    5. A submersible pump RCD trips while the sump is nearly full, and a staff member wants to lift the pump by its cable and then reset the RCD. What is wrong?

      Check my answer
      See the worked solution

      The power cable is not a lifting rope, and a pump whose circuit has not been isolated can make the water and chain live; a tripped RCD also signals a fault, so it is not reset repeatedly. The technician keeps people away from the sump, calls an authorized electrician for isolation and fault finding, and uses the standby pump and reduced upstream flow to buy time.

    6. A manager asks the technician to climb down tonight into a 2 m deep sump to pull a ball of rags from the pump. What is the technician’s answer?

      Check my answer
      See the worked solution

      A 2 m deep sump is a confined space under Permenaker 11/2023 and holds wastewater that can release hydrogen sulfide and deplete oxygen, so entry requires an entry permit and licensed confined space K3 personnel. The technician does not climb down; that night the standby pump and reduced upstream flow are used, and the pump is lifted by its chain from above after electrical isolation if the arrangement allows.

    References

    External sources

    • Peraturan Menteri Ketenagakerjaan Nomor 11 Tahun 2023 tentang Keselamatan dan Kesehatan Kerja di Ruang Terbatasjdih.kemnaker.go.id
    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
    • NIOSH Pocket Guide to Chemical Hazards: Hydrogen sulfidecdc.gov
    • EH40/2005 Workplace exposure limitshse.gov.uk
    • Safe work in confined spaces. Confined Spaces Regulations 1997. Approved Code of Practice and guidance (L101)hse.gov.uk
    • Working with sewage: The health hazards. A guide for employers (INDG198)hse.gov.uk
    • Electrical safety and you: A brief guide (INDG231)hse.gov.uk
    • Wastewater Technology Fact Sheet: Sewers, Pressureepa.gov
    • Decentralized Systems Technology Fact Sheet: Low Pressure Pipe Systemsepa.gov

    Revision history

    DateVersionChange
    November 14, 20261First published

    How to cite

    Kurnia (2026). Wastewater pumps and building sumps: submersible pumps, floats and alarms, check valves, odor and gas in the sump, cleaning, and the limits of confined space entry. ARSTEMA Academy. Revised November 14, 2026. arstema.com/en/academy/konsep/pompa-air-limbah-dan-bak-penampung-gedung-pompa-celup-pelampung-dan-alarm-katup-searah-bau-dan-gas-di-bak-pembersihan-serta-batas-masuk-ruang-terbatas

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A sump of 2.0 m by 1.5 m with a 0.30 m level band is emptied by a 5 L/s pump, and the manufacturer allows 6 starts per hour. Calculate the working volume, the shortest cycle, and the maximum starts of one pump.

    2

    The alarm siren sounds three times a week, but every time it is checked the water level has already fallen, so a staff member proposes tying the alarm float higher. What is the technician’s answer?

    3

    The reserve volume above the alarm is 0.5 m³ and the busy-hour inflow is 1.5 L/s. How long until overflow if both pumps fail, and what does this mean for the alarm response?

    Self-assessment progress0%

    Nearby chapters