By Kurnia · Published November 14, 2026 · Version 1 · 20 min read
Hotel garden irrigation
plant water needs, sprinklers and drip irrigation, timers and rain sensors, pumps and filters, recycled water, and calculating flow and watering schedules
A hotel’s garden sprinklers run for 30 minutes at eleven in the morning all year round, including rainy days, while the sidewalks stay wet and the shrubs in the drip beds wilt. This chapter covers hotel garden irrigation from the building technician’s side: plant water needs from reference evapotranspiration and the landscape coefficient, sprinklers, pressure, and uniformity, drip and microirrigation with filters and pressure regulators, timers, rain sensors, and cycle and soak, pumps, meters, and backflow prevention, recycled water, and how to calculate the precipitation rate in millimeters per hour, runtimes, zone flow, and a weekly schedule. Guidance and coefficient ranges come from the US EPA WaterSense program; recycled water quality is given as US guidance, and use in Indonesia follows the permits and quality standards of the competent authority.
At a resort hotel, the lawn sprinklers in the front garden run for 30 minutes at eleven in the morning, every day all year round, including rainy days. Guests complain that the sidewalks are always wet, some sprinkler heads spray the entrance drive, and the shrubs in the drip-irrigated beds are wilting because their emitters are clogged. The finance department asks why water use has gone up, and management wants to use treated water from the hotel’s wastewater treatment plant to water the garden.
The chief engineer asks the technician to answer three questions: how much water the plants actually need, how long each zone needs to run, and what must be confirmed before treated water enters the irrigation pipes. All three are answered with simple calculations and field checks, not by guessing minutes.
Scope
This chapter covers irrigation of hotel, hospital, and laundry complex grounds from the building technician’s side: reading plant water needs, inspecting sprinklers and drip irrigation, setting schedules, checking filters, meters, and backflow prevention, and calculating flow and runtimes. Pump selection and pump curves are covered in Chapter 9 · Buildings & Facilities on building water pressure and pumps, groundwater and boreholes in Chapter 27, laundry wastewater and WWTPs in Chapter 17 · Laundry, wastewater characteristics in Chapter 16, and laundry water recycling in Chapter 24. Backflow and cross-connections are in Chapter 11 · Buildings & Facilities on backflow prevention, valves in Chapter 12 · Buildings & Facilities, solenoid valves in Chapter 62 · Electrical & Control, water meters in Chapter 5 · Fluids & Thermal on flow measurement, media filters in Chapter 20, Legionella in Chapter 10 · Utilities on cooling towers, and fountains in Chapter 38 on fountains and ornamental ponds.
Electrical work on pump panels, timer supplies, and outdoor cable connections belongs to an authorized electrician. Using treated wastewater for watering follows the permits and quality standards set by the environmental authority; this chapter does not give Indonesian quality standard figures because their text was not checked. Redesign of the pipe network and zones is handed to an irrigation designer or contractor.
Plant water needs
Plants and soil lose water through evapotranspiration, the amount of water lost by evaporation from the soil and transpiration from plants. The water theoretically needed to keep a landscape healthy equals the water lost through evapotranspiration, and irrigation makes up the shortfall that rain does not cover. Reference evapotranspiration (ETo) is the water lost from a well-maintained expanse of average-height green grass and the surrounding soil. It depends on sun, wind, humidity, and temperature: hot, dry, and windy places have higher ETo than cool, humid places. ETo data are taken from a local weather station or meteorological agency.
Other plants do not use as much water as the reference grass. The landscape coefficient () is a multiplier on ETo that represents the plant species, the conditions at the site, and planting density:
where is the species factor, the microclimate factor (sun, wind, reflection from walls), the density factor, and the landscape evapotranspiration (mm/day). WaterSense guidance states that and range from 0.5 to 1.4 and takes both as about 1.0 to simplify the calculation. As a rule of thumb, high water-using plants use 70 to 90 percent of ETo, moderate ones 40 to 60 percent, and low ones less than 30 percent; these are relative comparisons from California data, not exact requirements for each plant.
Rain reduces the irrigation need, but not by its full amount. Part of a heavy rain runs off the surface before it soaks in, and the part useful to plants, effective rainfall, is often taken as about 50 percent. The WaterSense water budget tool counts only 25 percent of the 30-year average rainfall so that the design holds up in dry years. The net and gross requirements of a zone over a period are:
where is the net requirement (mm), the effective rainfall (mm), the gross requirement (mm), the lower-quarter distribution uniformity (dimensionless, explained in the sprinkler section), the zone area (m²), and the water volume (L), because 1 mm of water over 1 m² equals 1 L. Dividing by uniformity is a conservative approach: the driest part of the zone still gets enough water. WaterSense stresses that its water budget tool is made for designing landscapes, not for setting watering amounts, because it would over-apply water; watering schedules are adjusted to real weather data and observation.
Plants with similar water needs are grouped in one hydrozone, which also takes account of soil, sun, shade, wind, and slope. Turf and shrubs are not watered in one zone, because their needs and watering devices differ. About 3 inches (about 7.6 cm) of mulch in planting beds and around trees reduces evaporation and holds water.
Sprinklers: pressure, uniformity, and precipitation rate
Fixed spray sprinklers water a small circle or sector at a high rate, while rotors turn one or more streams for a longer throw at a lower rate. With both types, the water that falls is not the same at every point. Head-to-head coverage means that water from one sprinkler reaches the adjacent sprinkler, so that distribution is as even as possible. A matched precipitation rate means that all nozzles in a zone apply the same amount of water per area per hour. Without uniformity, a zone is watered until its driest spot is green and the rest is flooded.
Pressure governs how a nozzle behaves. WaterSense notes that sprinkler nozzles typically operate optimally at 30 or 45 psi (207 or 310 kPa), while incoming pressure commonly exceeds 60 psi (414 kPa). Excess pressure gives excessive flow, misting, and uneven coverage, and pressure-regulating spray sprinkler bodies can reduce water use from spray sprinklers by more than 20 percent when incoming pressure is above 60 psi. The technician measures the pressure at the end of the zone while it runs and compares it with the nozzle manufacturer’s data.
The precipitation rate is the depth of water a zone applies per hour:
where is the precipitation rate (mm/h), the total zone flow (L/min), and the watered zone area (m²). The formula assumes water falls evenly over the whole zone; the unevenness is measured separately. Lower-quarter distribution uniformity () is the ratio of the average of the lowest 25 percent of measurements to the average of all measurements. The measurements are taken with catch containers set out in a grid in the zone while it runs; WaterSense suggests a simple method with empty cans to see how long the sprinkler takes to fill them with half an inch of water.
A full audit by a qualified irrigation auditor is recommended every three years, with ANSI/ASABE S626 as the guideline for uniformity and application rate testing.
The precipitation rate is also compared with how fast the soil can absorb water. Clay soil absorbs slowly and slopes make water run off quickly, so sprinklers with a high rate cause ponding and runoff. For new WaterSense labeled homes in the United States, sprinklers may only be used on turf that is not on slopes steeper than 4:1 and not in strips narrower than 4 feet.
Drip and microirrigation
Microirrigation is low-pressure, low-flow irrigation that delivers water directly to the root zone; under the ASABE/ICC 802-2014 standard cited by EPA, its emission devices discharge less than 30 gallons per hour at 30 psi. Its forms are drip line with evenly spaced emitters, point-source emitters for a single plant, multiple-outlet emitters, and microsprays. Microirrigation is most effective for trees, shrubs, and ornamental plants spaced widely apart, not for expanses of turf that cover the whole soil. Microirrigation uses 20 to 50 percent less water than conventional spray sprinklers.
Three components at the point of connection decide its success. First, the filter: according to that guide, city water generally needs only a basic filter, but untreated well water or surface water may need a screen filter because it carries soil particles and organic matter. Second, the pressure regulator: emitters, microsprays, and drip line are designed to operate between 15 and 30 psi, and pressure above 30 psi can raise the flow and cause system failure, so a pressure regulator or pressure-compensating emitters are fitted. Third, a backflow preventer that local codes may require to protect drinking water from irrigation water.
Emitters are clogged by soil, mulch, weed roots, or unfiltered water. Drip lines are flushed regularly, especially in systems that use nonpotable water, and abnormal flow at the meter can reveal a leak hidden under mulch. The equivalent precipitation rate of a drip bed is calculated with the same formula, using the flow of all emitters and the bed area (Example 5), noting that drip water wets the root zone, not the whole surface.
Timers, rain sensors, and cycle and soak
A clock timer opens the zone valves on a fixed schedule. WaterSense labels two smarter types of controller: the weather-based irrigation controller, which tailors the amount, frequency, and timing of watering to local weather data and landscape conditions, and the soil moisture-based irrigation controller, which uses a sensor in the soil to enable or cancel watering. Labeled controllers that are properly installed and programmed can reduce irrigation water use by 15 to 30 percent. Beyond that, rain sensors prevent watering when rainfall is sufficient, wind sensors interrupt watering in strong wind, and flow monitoring can interrupt watering when excess flow from broken pipes or sprinkler heads is detected.
The result of a controller depends on its settings. WaterSense writes that controllers that are not properly set or are overridden do not deliver savings. The schedule is adjusted to the season; watering in the middle of the day is avoided because the sun evaporates much of the water before it reaches the plants. Applying larger volumes less often is generally better because it encourages deep roots.
Cycle and soak is dividing a zone’s runtime into several short cycles with pauses so that the water has time to soak in. The zone is turned on and the minutes until water starts to pool are recorded; that time becomes the limit for one cycle. If that limit is equal to or longer than the daily runtime, cycle and soak is not needed. In areas with distinct wet and dry seasons, the schedules for the two seasons are stored as two separate programs.
Zone valves are usually solenoid valves, as in Chapter 62 · Electrical & Control, driven by a low-voltage timer. The timer supply, pump panel, and outdoor junction boxes are protected by RCDs and worked on by an authorized electrician, as in Chapter 22 · Electrical & Control on RCDs. The irrigation technician does not open live enclosures that are wet or flooded.
Pumps, filters, meters, and backflow
Large grounds are often supplied by a pump from an irrigation tank, a well, or the building network. Pump curves, pressure, and selection are covered in Chapter 9 · Buildings & Facilities, and boreholes in Chapter 27. From the irrigation side, the checks are the zone pressure while it runs, the main filter, which is cleaned when its pressure drop rises, a pressure-reducing valve where incoming pressure is high, and check valves in sprinklers that retain water in the lateral pipes between cycles.
A dedicated irrigation meter records the water actually applied to the landscape. WaterSense recommends a dedicated meter and recording its usage trends as part of maintenance; regular reading helps show the results of savings and find leaks quickly. Reading the meter before and after one zone runs gives the actual flow of that zone, which is compared with the sum of the nozzle flows (Example 6). An actual flow that is much higher points to a leaking pipe, a broken head, or a missing nozzle; one that is much lower points to a clogged filter, a valve that does not open fully, or low pressure.
Irrigation pipes are in contact with soil, fertilizer, and sometimes recycled water, so there must be no path for that water back into the drinking water network. Backflow preventers are installed, tested, and recorded according to Chapter 11 · Buildings & Facilities on backflow prevention. A hose with its end submerged in a pond or a fertilizer bucket is the cross-connection most often missed.
Recycled water and other sources
WaterSense places alternative water sources after efficiency: the system is first made as efficient as possible, and then alternative sources are used where environmentally appropriate and allowed by local regulations. For a hotel, such sources can be roof rainwater, treated WWTP effluent, or treated laundry wastewater as in Chapter 24. In Indonesia, using treated wastewater for watering follows the permits and quality standards of the environmental authority; as of November 2026 the text of those rules could not be checked, so this chapter gives no Indonesian quality standard figures.
As an idea of the level of treatment required elsewhere, the 2012 EPA guidelines for water reuse suggest, for unrestricted urban reuse where public access is not restricted, secondary treatment, filtration, and disinfection, with pH 6.0 to 9.0, BOD of no more than 10 mg/L, turbidity of no more than 2 NTU, no detectable fecal coliform per 100 mL, a chlorine residual of at least 1 mg/L, and a setback of 15 m to potable water supply wells. The guidelines also ask for water that is clear and odorless. These are suggested US guidelines, not Indonesian quality standards, and each state uses its own rules.
Recycled water also raises the question of spray. The UK HSE treats any water system as a reasonably foreseeable Legionella risk if it has any of these factors: the bacteria are present, the water temperature may be between 20 and 45 °C, the system creates or spreads breathable droplets, it stores or recirculates water, or it contains a food source for the bacteria such as sludge, rust, scale, organic matter, and biofilms. An irrigation tank exposed to the sun in the tropics and sprinklers that spray near guest paths meet several of those conditions, so the system is included in the hotel’s water risk assessment as in Chapter 10 · Utilities. Recycled water pipes are clearly marked, not connected to the drinking water network, and taps on that line are not used for drinking or hand washing.
Calculating flow and watering schedules
The schedule calculation follows the same order for each zone:
- The gross weekly requirement from ETo, , effective rainfall, and .
- The precipitation rate from the zone flow and area, preferably corrected with catch-can test results.
- The weekly runtime in hours, then divided over several watering days.
- The daily time divided again into cycles shorter than the time to ponding.
- The volume per zone , summed over all zones and compared with the pump and tank capacity and the meter readings.
The number of watering days depends on the soil. Coarse soil needs frequent watering, medium loamy soil longer and less frequent watering, and fine clay soil with a high water-holding capacity the least frequent watering; water beyond what the soil can hold is wasted as runoff or deep percolation. The initial schedule from the calculation is always checked in the field: the moisture of the soil in the root zone is checked the day after watering, ponding and runoff are observed, and the schedule is adjusted.
Worked example
The numbers in the examples below are practice numbers unless their origin is stated.
Example 1: water need of a turf zone. A 400 m² zone of high water-using turf has , ETo of 5.0 mm/day, and a week without rain. Its landscape evapotranspiration is mm/day, that is mm/week. With , the gross requirement is mm/week, and the volume is L, about 17.2 m³ per week.
Example 2: precipitation rate of a sprinkler zone. Ten spray heads of 7.5 L/min each water 160 m², so the zone flow is 75 L/min. Its precipitation rate is mm/h. This zone applies 28.1 mm of water in one hour, roughly the net requirement of the turf in Example 1 for a whole week.
Example 3: runtime and cycle and soak. The zone in Example 2 is part of the turf in Example 1, so its gross requirement is 43.1 mm/week. Its runtime is hours, that is about 92 minutes per week. Divided over three watering days, each day is 30.7 minutes. Water starts to pool after 8 minutes, so the daily time is divided by , rounded to 4 cycles of about 7.7 minutes with soak pauses in between. The old schedule, 30 minutes every day, gives mm per week, more than twice the gross requirement.
Example 4: catch-can test and uniformity. Eight cans in the zone of Example 2 collect 12, 9, 14, 6, 11, 13, 7, and 10 mm after the zone runs for 20 minutes. The average is mm. The lowest quarter is two cans, 6 and 7 mm, with an average of 6.5 mm, so . The measured precipitation rate is mm/h, slightly above the calculated 28.1 mm/h, perhaps because the pressure is higher than in the nozzle data. The schedule is recalculated with the measured figure, and the cause of the two dry cans is sought at the nearest sprinkler heads.
Example 5: a drip-irrigated bed. A 90 m² hedge bed holds 60 shrubs, each with two 2 L/h emitters, so the flow is L/h and the equivalent rate is mm/h. Moderate water-using shrubs with and ETo of 5.0 mm/day need mm/week; with the gross requirement is 19.4 mm, that is L. The runtime is hours per week, for example three times 2.4 hours. This low rate is what lets drip water soak in without runoff.
Example 6: actual flow from the irrigation meter. The zone in Example 2 runs for 30 minutes and the irrigation meter rises from 1,204.30 m³ to 1,207.20 m³, that is 2.90 m³. The expected volume is L, so the excess is L or percent. A difference that large points to a leaking pipe, a broken sprinkler head, or a missing nozzle, and the zone is inspected while running before the new schedule is used.
Stop conditions
- The timer enclosure, pump panel, or outdoor junction box is wet, flooded, smells burned, or its RCD trips repeatedly: do not open or touch it; switch off from a dry panel if a procedure for that exists, and an authorized electrician takes over as in Chapter 22 · Electrical & Control.
- The backflow preventer is missing or has failed its test, or a connection between the recycled water pipe and the drinking water network is found: stop using that line, and a competent plumber and a backflow preventer tester take over as in Chapter 11 · Buildings & Facilities.
- The permit and water quality test results for the recycled water are not available, or the water is turbid, smells, or is colored: stop using the recycled water and switch to a clean water source; the WWTP operator and the hotel’s environmental officer decide.
- Spray from a warm irrigation tank or from recycled water reaches guest areas, the pool, or room windows: stop that zone and report to the hotel’s water management team for a Legionella risk assessment as in Chapter 10 · Utilities.
- A pipe repair would require digging near buried cables, gas pipes, or main water pipes whose location is unknown: postpone until the utility drawings have been checked and the network owner has marked the location.
- The pump is running dry, making cavitation noise, or overheating: switch the pump off, and a pump technician inspects it as in Chapter 9 · Buildings & Facilities.
- Sprinklers are spraying roads, steps, or floors so that they become slippery, or are wetting garden lights and outdoor sockets: stop that zone; the heads are realigned, and wet electrical equipment is inspected by an authorized electrician.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
Every zone can be watered for the same number of minutes.
Why is it wrong?
Sprinkler, rotor, and drip zones have very different precipitation rates, and their plants have different coefficients. The same minutes give very different depths of water.
Common misconception
The more often plants are watered, the healthier they are.
Why is it wrong?
Frequent, shallow watering gives shallow roots that wilt easily. Watering more with longer intervals, adjusted to the soil, encourages deep roots.
Common misconception
City water is clean, so drip irrigation needs no filter or pressure regulator.
Why is it wrong?
Small particles still build up in the emitters, and network pressure can exceed the working range of the emitters. The filter and pressure regulator are part of a drip system.
Common misconception
Recycled water is safe for sprinklers because it has been treated.
Why is it wrong?
Quality that is good enough for discharge to a drain is not necessarily good enough for spraying near people. Its use for watering follows the permits and quality standards, and its spray is included in the water risk assessment.
Common misconception
A rain sensor means the schedule never needs resetting.
Why is it wrong?
A rain sensor only cancels watering when it rains; the amount applied on dry days still follows the settings. The schedule is still adjusted to the season.
Links to other chapters
Pumps and pump curves are covered in Chapter 9 · Buildings & Facilities on building water pressure and pumps, boreholes in Chapter 27 on groundwater and boreholes, and water demand and pipe sizing in Chapter 8 · Buildings & Facilities. Treated wastewater continues in Chapter 17 · Laundry on laundry wastewater and WWTPs, Chapter 16 on wastewater characteristics, and Chapter 24 on laundry water recycling. Backflow is in Chapter 11 · Buildings & Facilities, valves in Chapter 12 · Buildings & Facilities on valves and water control, solenoid valves in Chapter 62 · Electrical & Control, meters in Chapter 5 · Fluids & Thermal on flow measurement, and RCDs in Chapter 22 · Electrical & Control. Legionella from spray is covered in Chapter 10 · Utilities on cooling towers, and fountains and ornamental ponds in Chapter 38.
Exercises and worked solutions
The numbers in the exercises are for practice.
Try to answer first, then open the worked solution.
A 250 m² zone of low water-using shrubs has , ETo of 4.5 mm/day, no rain, and . What is the gross water volume per week?
Check my answer
See the worked solution
The landscape evapotranspiration is mm/day or mm/week, and the gross requirement is mm. The volume is L per week, far below turf of the same area because the coefficient is low.
Six rotors of 12 L/min each water 300 m². What is the precipitation rate, and how many minutes are needed to apply 20 mm?
Check my answer
See the worked solution
The zone flow is L/min, so mm/h. Applying 20 mm takes hours, about 83 minutes, much longer than a spray zone for the same depth because the rotor rate is lower.
Why is the schedule of eleven in the morning every day all year round in the opening case wasteful, even though the plants look green?
Check my answer
See the worked solution
At midday much of the water evaporates before it reaches the roots, and the same schedule all year applies water on rainy days and in humid seasons when the need is low. Example 3 shows that the schedule gives more than twice the gross requirement, so green plants do not prove that the schedule is efficient.
The WaterSense water budget tool uses a conversion factor of 0.6233 to give gallons from inches and square feet. Show where that number comes from and its SI equivalent.
Check my answer
See the worked solution
One inch of water (25.4 mm) over one square foot (0.092903 m²) has a volume of L, and with 1 gallon equal to 3.7854 L, gallons, consistent with 0.6233. In SI units the equivalent is simple: 1 mm of water over 1 m² equals 1 L.
Management wants treated WWTP water to feed the sprinklers near the swimming pool from next week. What has to be confirmed first?
Check my answer
See the worked solution
The permit and quality standards for using treated water from the environmental authority, recent water quality test results, and the monitoring arrangements have to be in place first, because quality good enough for discharge is not necessarily good enough for spraying. The line also has to be separated from drinking water by a tested backflow preventer, its pipes marked, and the spray near the pool included in the Legionella risk assessment; until all that is in place, the sprinklers keep using clean water.
A broken rain sensor is replaced, and irrigation water use is normally 120 m³ per month. A Florida field study cited by WaterSense found that homes with a rain sensor used 14 percent less water. What saving can be expected, and how is it proven?
Check my answer
See the worked solution
If the result matched that study, the saving would be m³ per month, but that figure is data from homes in Florida and depends on local rainfall. The saving is proven by comparing readings of the dedicated irrigation meter before and after the replacement in months with comparable rainfall.
References
External sources
- WaterSense at Work Section 5.2: Irrigationepa.gov
- WaterSense at Work Section 5.1: Landscapingepa.gov
- WaterSense Water Budget Approachepa.gov
- Adding Microirrigation to Your Services: A Mini-Guide for Irrigation Professionalsepa.gov
- Watering Tipsepa.gov
- Cycle-and-Soak Saves Water Outdoorsepa.gov
- 2012 Guidelines for Water Reuseepa.gov
- Other systems that can create a risk of legionellahse.gov.uk
Revision history
| Date | Version | Change |
|---|---|---|
| November 14, 2026 | 1 | First published |
How to cite
Kurnia (2026). Hotel garden irrigation: plant water needs, sprinklers and drip irrigation, timers and rain sensors, pumps and filters, recycled water, and calculating flow and watering schedules. ARSTEMA Academy. Revised November 14, 2026. arstema.com/en/academy/konsep/irigasi-taman-hotel-kebutuhan-air-tanaman-sprinkler-dan-irigasi-tetes-pengatur-waktu-dan-sensor-hujan-pompa-dan-saringan-air-daur-ulang-serta-menghitung-debit-dan-jadwal-siram
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
A 250 m² zone of low water-using shrubs has , ETo of 4.5 mm/day, no rain, and . What is the gross water volume per week?
Six rotors of 12 L/min each water 300 m². What is the precipitation rate, and how many minutes are needed to apply 20 mm?
Why is the schedule of eleven in the morning every day all year round in the opening case wasteful, even though the plants look green?
Nearby chapters
Reading order by shelf: Water & Water Treatment · Chapter 38.
Reading order by shelf: Water & Water Treatment · Chapter 36.
Another chapter in Water & Water Treatment.