Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Water & Water Treatment · Chapter 43Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Swimming pool suction outlets and entrapment hazards

    suction openings and their covers, flow velocity at the cover, dual suction outlets and vacuum release, the pump emergency shutoff, and daily inspection

    On the morning before the children’s pool of a resort hotel opens, the pool attendant finds the main drain cover cracked and one of its bolts missing, although the day before a guest reported that their child felt sucked in while sitting near that opening, a new and larger pump has just been installed, and the pump emergency shutoff on the pool wall is hidden behind a towel rack. This chapter covers entrapment hazards at swimming pool suction outlets from the building technician’s side: pool suction openings and the types of entrapment according to WHO and the CDC Model Aquatic Health Code, suction outlet covers and their grille gaps, flow velocity at the cover and the suction holding force, dual suction outlets and flow sharing, vacuum release, the pump emergency shutoff, and the daily inspection before the pool opens. Removing, replacing, or altering covers, changing the suction piping, adjusting or bypassing vacuum release, electrical work on pumps, and entering the balance tank are the work of pool contractors, designers, and authorized electricians; the building technician inspects, closes the pool, and reports.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    On the morning before the children’s pool of a resort hotel in Bali opens, the pool attendant finds the main drain cover cracked on one side and one of its fixing bolts missing. The afternoon before, a guest reported that their child felt “sucked in” while sitting on the pool floor near that opening, and then managed to stand up unaided. A week earlier the contractor had replaced the circulation pump with a larger one, and one of the two main drains of the children’s pool was covered by a layer of leaves that had never been cleared. The pump emergency shutoff on the wall near the pool is hidden behind a new towel rack. These four things look separate, but all of them decide how strong the suction is at one opening and how quickly that suction can be stopped.

    Scope

    This chapter covers entrapment hazards at the suction outlets of swimming pools in hotels, resorts, and hospital fitness centers from the building technician’s side: suction openings and the types of entrapment, suction outlet covers and their grilles, flow velocity at the cover, dual suction outlets, vacuum release, the pump emergency shutoff, and daily inspection. The annex of Permenkes 2/2023 (Minister of Health Regulation) on swimming pool water asks that the pool be kept full and its water recirculated. As of November 2026, JDIH Kemenkes lists Permenkes 2/2023 as no longer in force because it was revoked by Permenkes 3/2026, while Article 99 of Permenkes 3/2026 excludes several of its articles together with the annex from the revocation; Indonesian provisions on the design of pool suction outlets cannot yet be confirmed, so ask the pool designer and the relevant agency. The design figures in this chapter come from WHO, from the United States CDC Model Aquatic Health Code, which is published as guidance, and from the UK HSE. The cover certification standard ANSI/APSP/ICC-16 2017 is a paid standard and is only named.

    Circulation, skimmers, and main drains are in Chapter 29 on swimming pool circulation and filtration, pumps and prestrainers in Chapter 30 on swimming pool circulation pumps, water quality and the dosing pump interlock in Chapter 32 on swimming pool water quality, and spa suction outlets in Chapter 41 on hotel whirlpool baths. Emergency stop buttons in general are in Chapter 49 · Electrical & Control on buttons, indicator lights, colors, and emergency stops, emergency switching in Chapter 31 · Electrical & Control on isolation, switching, and emergency switching, LOTO in Chapter 76 · Electrical & Control on safe work, and RCDs in Chapter 22 · Electrical & Control on RCDs.

    Work outside the building technician’s authority: removing, fitting, replacing, or altering suction outlet covers and grilles; changing the suction piping or fitting and closing valves on the suction piping; adjusting, function-testing, relocating, or bypassing the vacuum release; replacing the pump with one of a different flow; all electrical work on the pump, panel, and emergency shutoff; and entering the balance tank or drain sump, which can count as a confined space. This work belongs to pool contractors, pool designers, vacuum release suppliers, and authorized electricians, and the care of a victim belongs to trained lifeguards and the emergency services. The building technician never runs the pump with a suction outlet cover that is damaged, missing, or loose. The building technician inspects from the poolside, records, presses the emergency shutoff in an emergency, tests the shutoff according to procedure when assigned, closes the pool when a Stop condition occurs, and reports.

    Pool suction openings and types of entrapment

    Suction outlet is any opening in the pool connected to the suction side of the pump: main drains, wall suction openings, skimmers, and the openings for vacuum cleaners. The pump draws water through the opening, so the pressure behind the opening is lower than the pool water pressure. While the water flows freely, that pressure difference is small. When a body covers the opening, the flow stops, the pump keeps drawing, and the pressure difference rises up to the suction capacity of the pump.

    Entrapment is the situation in which hair or a body part is held at a suction outlet so that the person cannot free themselves. The CDC Model Aquatic Health Code, hereafter MAHC, includes five types of entrapment in the pool operator training content: hair, limb, body, evisceration, and mechanical. WHO explains the mechanism: openings where the suction is extremely strong can trap hair or body parts so that the victim’s head is held under water, and most incidents involve people with shoulder-length or longer hair, whose hair is carried by the flow around the cover and then pulled into the opening.

    WHO cites United States data from the CPSC: 49 incidents of hair entrapment in hot tubs from 1990 to 1996, 13 of which resulted in drowning, and 18 cases of body entrapment over a 20-year period, ten of which resulted in evisceration and five others fatal. Children, typically between 8 and 16 years old, tend to play with open drains, put their hands or feet into the pipe, and become trapped by the suction. WHO writes that any open drain or flat grating that the body can cover completely, combined with a plumbing layout that lets suction build up when the drain is blocked, presents this hazard.

    The entrapment that injures fastest is evisceration. WHO notes that drain covers can become brittle and crack, or become loose and go missing; a person sitting on a broken cover or an uncovered drain can suffer that injury, especially young children in shallow pools. In the UK a six-year-old child was injured after being sucked onto a drain whose cover had been removed for cleaning and not put back. WHO also writes that it is uncertain whether suction reduced through multiple outlets and a velocity limit is as effective against this injury, because it occurs almost immediately at a small pressure difference. That is why an intact cover is the first line of defense, not an accessory.

    Suction outlet covers and their grilles

    Suction outlet cover is the perforated lid over the mouth of a suction outlet that limits what can enter the opening and spreads the flow over a wide area. MAHC asks that submerged suction outlet fitting assemblies be certified to ANSI/APSP/ICC-16 2017 and installed according to their installation instructions, including the sump depth below them, pipe sizes, frames, supports, and fasteners. Covers are labeled with a flow rating and as blockable or unblockable, and the manufacturer’s documentation for all covers and sumps is kept as a permanent facility record.

    WHO recommends grille gaps at outlets of less than 8 mm. HSE asks for suitable covers or grilles for wave machine openings, sumps, and the inlets and outlets of the circulation system, designed to prevent limbs and fingers getting trapped. For wave machine grilles HSE gives a gap between bars of less than 100 mm. The 100 mm figure is to keep a body out of the wave machine chamber, not a suction outlet grille gap; the two are not interchangeable.

    For the technician, the cover is judged from the poolside: intact with no cracks or breaks, all screws or bolts present and tight, not moving when pushed with a pole, and the same as the recorded cover. A different replacement cover, for example an ordinary flat grating or an unlabeled cover, changes the flow rating and the blockable classification, so a replacement is always matched to the pump flow by the designer (Example 2). MAHC prohibits skimmer equalizers in new construction or substantial alteration, because an equalizer line without a certified cover can become an entrapment point.

    Flow velocity at the cover

    WHO recommends that the velocity of water flowing from the pool through outlets not exceed 0.5 m/s, that there be at least two outlets for each suction line, and that the outlets be sized and located so they cannot be blocked by the body of a single bather. MAHC asks that flow velocities meet ANSI/APSP-16 based on 100 percent of design flow through each main drain cover. The 100 percent assumption means the calculation is done for the worst case: all other openings blocked and the whole flow passing through one cover.

    The average velocity through the cover openings is estimated with

    v=Qn Av = \frac{Q}{n\,A}

    where vv is the velocity through the cover openings (m/s), QQ the pump flow passing through that outlet (m³/s), nn the number of open covers, and AA the net open area of one cover (m²). The formula assumes the flow is evenly shared; local velocities in the grille gaps and at the cover edge are higher. If one of two covers is blocked by leaves or a body, nn falls from 2 to 1 and the velocity doubles (Example 1). A larger pump raises QQ and therefore vv, with nothing changed in the pool.

    The velocity at the cover differs from the velocity in the pipe. MAHC asks that suction piping be sized so the water velocity does not exceed 1.8 m/s and discharge piping 2.4 m/s, unless there is proper engineering justification. The pipe velocity is calculated with vpipe=4Q/(πd2)v_{pipe} = 4Q/(\pi d^2), where dd is the internal pipe diameter (m) (Example 4).

    Why can a person not pull free from a blocked opening? The force holding the body against the cover is approximately

    F=Δp AcoverF = \Delta p \, A_{cover}

    where FF is the holding force (N), Δp\Delta p the pressure difference between the pool water and the space under the cover (Pa), and AcoverA_{cover} the area of cover blocked by the body (m²). A pressure difference of a few tens of kilopascals on a cover area the size of an adult’s foot already produces a force equal to the weight of an adult (Example 5). That is why prevention rests on design and on stopping the pump, not on the strength of the rescuer.

    Dual suction outlets and flow sharing

    MAHC asks that covers labeled blockable be installed in a minimum of two, while covers labeled unblockable may be one or more. The openings are connected to a single main suction pipe by branch pipes that are not valved, so they cannot operate independently. Where there are two main drains, the branch pipe from each must be able to carry 100 percent of the design flow, and where there are three or more, the design flow of each branch may be

    Qmax=QtotalN−1Q_{max} = \frac{Q_{total}}{N - 1}

    where QmaxQ_{max} is the design flow of one branch (m³/h), QtotalQ_{total} the design circulation flow (m³/h), and NN the number of main drains. The MAHC Annex states the aim: if one drain is blocked, the remaining drains together still handle 100 percent of the flow. For a system of blockable covers, the system flow rating is the sum of the flow ratings of all covers minus the flow rating of the largest cover, that is, the capacity of the system when the largest cover is blocked (Example 2).

    The spacing between openings is also part of the design. The MAHC Annex names two suction fittings at least 3 feet apart, about 0.9 m, as one of the ways to prevent entrapment. Two openings close together can be covered by one body at once, so dual openings no longer mean two paths. A valve added to one branch, for example to balance the flow, removes the benefit of dual openings if it is closed; for the technician, such a valve is a finding reported to the designer, not a device to adjust.

    Vacuum release

    Safety vacuum release system (SVRS) is a system capable of providing vacuum release at a suction outlet when a high vacuum occurs because that outlet is blocked. The mechanical type is installed on the suction pipe before the pump and opens the pipe to the atmosphere when the vacuum passes a threshold, breaking the suction. The electrical type is attached to the pump control or built into the pump and shuts off the motor when the vacuum passes a threshold.

    The MAHC Annex treats vacuum release as a secondary line of defense: used together with other methods such as two suction fittings at least 3 feet apart or a single unblockable cover. The Annex also records its weaknesses. The vacuum release can be triggered by other vacuum changes, for example while the pool is being vacuumed; control valves or check valves on the suction piping can greatly affect or completely defeat its operation; and a pump shut off by the vacuum release might turn back on unexpectedly. The United States pool and spa safety act (VGB Act) required vacuum release for pools with a single main drain, while MAHC requires two main drains.

    For the building technician, three things follow from this. First, a triggered vacuum release is a sign that something is blocking an opening, so the pool is inspected first and the pump is not restarted before the cause is found. Second, valves, piping, or pumps on the suction side are not changed without the designer, because such changes can defeat the vacuum release. Third, the vacuum release is not bypassed, removed, or switched off because it trips often; repeated tripping is handed to the supplier or the pool contractor.

    Pump emergency shutoff

    Emergency shutoff is an easily reached switch near the pool for stopping the circulation pump and water feature pumps in an emergency. WHO lists an accessible emergency shut-off for the pump among the measures to prevent hair and body entrapment.

    For spas, MAHC asks for a clearly labeled emergency shutoff that stops the circulation and jet pump motors, readily accessible to bathers, within sight of the spa, and located not less than 5 feet (1,524 mm) and not more than 10 feet (3,048 mm) horizontally from the inside walls of the spa. The MAHC Annex gives a different range, 5 feet (1.5 m) to 50 feet (15.2 m), so the location of an installed shutoff is matched to the design documents and local rules, not guessed from either figure.

    HSE asks that pool features such as rivers and wave machines have a procedure for stopping them in an emergency. For the technician, the emergency shutoff is judged on three things: visible and labeled, not obstructed, and actually stopping the pump that draws from the suction outlets when tested according to procedure. Testing is scheduled when no bathers are in the pool, recorded, and followed by a check that the pump does not restart by itself.

    Stopping the pump also stops the flow to the dosing point. HSE records that most chlorine gas incidents at pools have happened when circulation stopped or was reduced but the automatic dosing system kept operating, so hypochlorite and acid built up and reacted; the gas was released into the pool hall when circulation was restored. For that reason every pump stop, including through the emergency shutoff, is followed by a check that the dosing pump has also stopped, as with the flow interlock in Chapter 32, and the circulation pump is restarted only by the designated person after the cause of the stop is clear.

    Daily inspection before the pool opens

    MAHC asks for a daily preventive maintenance inspection before opening, including that main drain covers, vacuum fitting covers, skimmer equalizer covers, and all other suction outlet covers are in place, secure, and unbroken; that skimmer baskets and suction outlets are free of blockage; that inlet covers are in place and intact; and that entrapment prevention systems are operational. The MAHC operator training content also includes the function of the pump emergency shutoff and of the vacuum release according to the manufacturer’s guidelines in the daily inspection.

    If a cover is loose, broken, or missing, MAHC asks that it be secured or replaced immediately according to the manufacturer’s requirements and that the pool be closed until the repair is complete. MAHC also classifies a broken, unsecured, or missing main drain grate or submerged suction outlet grate as an imminent health hazard for which the pool can be ordered closed immediately. WHO writes that pools and hot tubs should not be used if any covers are missing, unsecured, or damaged.

    The list below is compiled from these provisions for hotel pools. The inspection is done from the poolside, with clear water so the bottom is visible, before the pool opens.

    ItemWhat is checkedIf not in order
    Main drain and wall coversin place, intact, all fasteners present, same as the recordpool not opened; report to the contractor
    Skimmer baskets and suction openingsfree of leaves, plastic, and toysclean according to procedure after the pump is isolated
    Both main drainsboth open, not covered by leaves or siltpool not opened until both are clear
    Emergency shutoffvisible, labeled, unobstructed; tested on scheduleremove the obstruction; report a faulty shutoff to the electrician
    Vacuum releaselight or indicator normal, no alarmpump not restarted; report to the supplier
    Pump and gaugessound and readings the same as yesterdaya sharp rise in the suction reading can mean an opening is blocked; inspect the pool

    The daily record holds the time, the inspector’s name, the result of each item, and the action taken. MAHC asks that operation and maintenance records be kept for a minimum of three years. Cover replacements are recorded with the date, type, and flow rating, because the cover determines the velocity in Examples 1 to 3.

    Worked example

    The numbers in the examples below are practice numbers, unless their origin is stated.

    Example 1: velocity at the cover when one opening is blocked. The children’s pool pump delivers 54 m³/h, that is 54/3,600=0.01554/3{,}600 = 0.015 m³/s, through two main drains, each with a net open area of 0.040 m². With both open, v=0.015/(2×0.040)=0.19v = 0.015/(2 \times 0.040) = 0.19 m/s. If one is blocked by leaves, v=0.015/0.040=0.38v = 0.015/0.040 = 0.38 m/s, still below 0.5 m/s. After the pump is replaced with an 81 m³/h unit, Q=81/3,600=0.0225Q = 81/3{,}600 = 0.0225 m³/s and one blocked cover gives v=0.0225/0.040=0.56v = 0.0225/0.040 = 0.56 m/s, above 0.5 m/s, so the pump replacement is handed back to the designer.

    Example 2: system flow rating of two covers. Two blockable covers each have a flow rating of 60 m³/h. The system flow rating is 60+60−60=6060 + 60 - 60 = 60 m³/h, not 120 m³/h, because the largest cover is assumed blocked. An 81 m³/h pump exceeds 60 m³/h, so the pump or the covers must be redesigned by the designer.

    Example 3: required open area. For a flow of 81 m³/h, that is 0.0225 m³/s, through one cover at 0.5 m/s, the net open area must be at least A=0.0225/0.5=0.045A = 0.0225/0.5 = 0.045 m². A 0.040 m² cover is smaller than that; a larger cover is the designer’s decision because the sump and piping below also matter.

    Example 4: velocity in the suction pipe. A flow of 0.0225 m³/s in a suction pipe with a 0.10 m internal diameter gives vpipe=4×0.0225/(π×0.102)=2.86v_{pipe} = 4 \times 0.0225/(\pi \times 0.10^2) = 2.86 m/s, above 1.8 m/s. A 0.15 m pipe gives 4×0.0225/(π×0.152)=1.274 \times 0.0225/(\pi \times 0.15^2) = 1.27 m/s, below 1.8 m/s. A larger pump on old piping raises the pipe velocity and the cover velocity together.

    Example 5: the force holding a body. A child sits covering 0.030 m² of a cover, and the pressure difference under the cover rises to 25 kPa. The holding force is F=25,000×0.030=750F = 25{,}000 \times 0.030 = 750 N, equal to the weight of a 750/9.81=76750/9.81 = 76 kg mass. A child cannot resist a force that large, and a rescuer pulling can also injure the victim, so the first step is to press the pump emergency shutoff.

    Example 6: location of a spa emergency shutoff. MAHC asks that a spa emergency shutoff be not less than 5 feet and not more than 10 feet from the inside wall of the spa. With 1 foot equal to 0.3048 m, the range is 5×0.3048=1.525 \times 0.3048 = 1.52 m to 10×0.3048=3.0510 \times 0.3048 = 3.05 m. A shutoff installed 4.0 m from the spa wall is outside the Code range but inside the MAHC Annex range up to 15.2 m, so its location is matched to the design documents and local rules.

    Stop conditions

    1. A main drain cover, wall suction cover, vacuum fitting cover, or skimmer equalizer cover is cracked, broken, loose, shifted, missing, short of fasteners, or different from the record: get all bathers out, have the designated person stop the pump with the emergency shutoff or from the panel, close the pool, do not remove, wedge, or replace the cover, and hand the repair to the pool contractor; the pool reopens only after the repair has been inspected.
    2. A person’s hair, limb, or body is held at a suction outlet: press the pump emergency shutoff at once, shout for help, and call the trained lifeguard and the emergency services; the care of the victim is handed to them.
    3. The vacuum release has tripped, its alarm is on, or the pump has stopped by itself, or someone proposes bypassing, removing, or switching off the vacuum release because it trips often: do not restart the pump before the pool has been inspected and the cause found, close the pool, and hand it to the vacuum release supplier or the pool contractor.
    4. The pump emergency shutoff does not stop the pump when tested, its label is missing, or it cannot be reached: the pool is not opened until an authorized electrician has repaired it.
    5. One of the main drains is covered by silt, leaves, or an object, or a valve on one branch pipe is closed, so only one suction opening is working: close the pool and report to the designer or pool contractor; do not open the pool with one opening.
    6. The pump has been replaced with a larger flow, a cover replaced with a different type, or the suction piping altered without the designer’s calculation: the pool is not opened until the designer has checked the velocity and the cover flow rating.
    7. The work requires a hand or tool to go into a suction outlet, skimmer, or prestrainer while the pump has not been stopped, locked, and tagged by an authorized person, or the balance tank would have to be entered without a confined space entry permit: do not start until isolation is confirmed, or stop until the permit is issued.
    8. The circulation pump has stopped, including through the emergency shutoff, but the dosing pump keeps running, or a strong chlorine smell is noticed in the pool hall or pump room: do not restart the circulation pump, get people out of that room, and hand it to the water treatment provider and the designated staff under the emergency response plan.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    A slightly cracked cover still holds a child, so the pool can open.

    Why is it wrong?

    A crack makes the cover brittle so it can break under a body, and evisceration injury happens almost immediately. MAHC asks that the pool be closed until the cover is repaired, and WHO asks that the pool not be used if a cover is damaged.

    Common misconception

    Two main drains make the pool safe, whatever their condition.

    Why is it wrong?

    The benefit of two openings is lost if one is blocked, if a branch valve is closed, or if they are so close together that one body covers both.

    Common misconception

    A vacuum release that trips often can simply be switched off.

    Why is it wrong?

    Tripping is a sign of high vacuum at the suction outlet. Switching it off removes the secondary line of defense, and the cause is handed to the supplier.

    Common misconception

    A stronger pump makes the water cleaner with no side effects.

    Why is it wrong?

    A larger flow raises the velocity at the cover and in the suction pipe, as in Examples 1 and 4, and can exceed the cover flow rating.

    Common misconception

    If a child is trapped, pull as hard as you can.

    Why is it wrong?

    The suction holding force can equal the weight of an adult, and pulling can injure the victim. The suction is stopped first with the emergency shutoff.

    The circulation flow that sets the velocity at the cover is calculated as in Chapter 29, and the pump, prestrainer, and their isolation are in Chapter 30. Stopping the pump and the dosing interlock relate to Chapter 32, and spa suction outlets, which are smaller and more dangerous for hair, are covered in Chapter 41. The pressure and continuity behind the velocity formula are in Chapter 1 · Fluids & Thermal on pressure, flow, and continuity, and pressure differences in Chapter 9 · Physics on fluid statics.

    Exercises and worked solutions

    The numbers in the exercises are for practice.

    Try to answer first, then open the worked solution.

    1. A 36 m³/h pump draws from two main drains, each with a net open area of 0.030 m². What is the velocity at the cover with both open and with one blocked?

      Check my answer
      See the worked solution

      The flow is 36/3,600=0.0136/3{,}600 = 0.01 m³/s, so with two covers open v=0.01/(2×0.030)=0.17v = 0.01/(2 \times 0.030) = 0.17 m/s and with one blocked v=0.01/0.030=0.33v = 0.01/0.030 = 0.33 m/s. Both are below 0.5 m/s, but those figures hold only as long as the pump and the covers do not change.

    2. A pool has four main drains and a design flow of 120 m³/h. What is the design flow of each branch according to MAHC, and why is it not 30 m³/h?

      Check my answer
      See the worked solution

      According to MAHC, Qmax=120/(4−1)=40Q_{max} = 120/(4 - 1) = 40 m³/h per branch. The figure of 30 m³/h would hold only if all four openings were always open; the design uses N−1N - 1 so that when one opening is blocked, the other three still handle the whole flow.

    3. In the morning the attendant finds one screw of a main drain cover missing, although the cover is still in place. What does the technician do?

      Check my answer
      See the worked solution

      A cover short of fasteners counts as unsecured, so under MAHC the pool is closed until it is repaired. The technician does not open the pool, has the pump stopped if bathers can get near, records the finding, and hands the fitting of the fasteners to the pool contractor.

    4. The vacuum release has stopped the pump twice in a week, and the cleaning contractor proposes fitting a bypass valve. What is the technician’s position?

      Check my answer
      See the worked solution

      Repeated tripping indicates high vacuum or a fault on the suction side, and according to the MAHC Annex a valve on the suction piping can defeat the vacuum release. The technician refuses the bypass valve, closes the pool if the cause is not yet clear, and hands the investigation to the vacuum release supplier or the pool contractor.

    5. One cover has a flow rating of 45 m³/h and the other 60 m³/h, both blockable. What is the system flow rating, and is a 54 m³/h pump suitable?

      Check my answer
      See the worked solution

      The system flow rating is 45+60−60=4545 + 60 - 60 = 45 m³/h, because the largest cover is assumed blocked. A 54 m³/h pump exceeds 45 m³/h, so the arrangement is not suitable and is handed to the designer.

    6. Why is the pump emergency shutoff tested when no bathers are in the pool, and what is checked afterward?

      Check my answer
      See the worked solution

      The test stops circulation and can trigger unexpected conditions, so it is done with no bathers in the water. Afterward it is checked that the circulation pump has really stopped, does not restart by itself, and that the dosing pump has also stopped; the pump is then restarted by the designated person and the result recorded.

    References

    External sources

    • Guidelines for safe recreational water environments. Volume 2: Swimming pools and similar environmentsiris.who.int
    • 2024 Model Aquatic Health Code, 5th Edition: Code Languagecdc.gov
    • Annex to the 2024 Model Aquatic Health Code, 5th Edition: Scientific and Best Practices Rationalecdc.gov
    • Health and safety in swimming pools (HSG179)hse.gov.uk
    • Peraturan Menteri Kesehatan Nomor 2 Tahun 2023 tentang Peraturan Pelaksanaan Peraturan Pemerintah Nomor 66 Tahun 2014 tentang Kesehatan Lingkunganjdih.kemkes.go.id
    • Peraturan Menteri Kesehatan Nomor 3 Tahun 2026 tentang Penanggulangan Penyakitjdih.kemkes.go.id

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Swimming pool suction outlets and entrapment hazards: suction openings and their covers, flow velocity at the cover, dual suction outlets and vacuum release, the pump emergency shutoff, and daily inspection. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/saluran-isap-kolam-renang-dan-bahaya-jeratan-lubang-isap-dan-penutupnya-kecepatan-aliran-pada-penutup-saluran-isap-ganda-dan-pelepas-vakum-tombol-henti-pompa-serta-pemeriksaan-harian

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A 36 m³/h pump draws from two main drains, each with a net open area of 0.030 m². What is the velocity at the cover with both open and with one blocked?

    2

    A pool has four main drains and a design flow of 120 m³/h. What is the design flow of each branch according to MAHC, and why is it not 30 m³/h?

    3

    In the morning the attendant finds one screw of a main drain cover missing, although the cover is still in place. What does the technician do?

    Self-assessment progress0%

    Nearby chapters