By Kurnia · Published November 14, 2026 · Version 1 · 20 min read
Hotel fitness equipment
treadmills and stationary bikes, electrical supply and emergency stops, daily checks, belts and wire ropes, lubrication, and limits of work
A guest falls from a treadmill in a hotel gym late in the evening: the safety key clip is kept in a drawer, the running belt jerks every time a foot lands, and two treadmills and one stationary bike are plugged into one extension reel. This chapter covers hotel fitness equipment from the building technician’s side: how treadmills, stationary bikes, and cable weight machines are built, belt speed and motor current, dedicated circuits and the safety key as an emergency stop, the free area behind a treadmill, daily checks and records, running belt tension and tracking, signs of wear on wire ropes, lubrication of the deck and guide rods, and how to take equipment out of use. HSE guidance from the United Kingdom and fitness center criteria from the United States are written as data from those countries, and Permenaker 12/2015 is used for the division of electrical work. Opening the motor hood and the control board, repairing motors and boards, and replacing the running belt, deck, or wire ropes are the supplier technician’s work.
At ten in the evening, the front desk of a hotel takes a call from the gym: a guest has fallen from a treadmill and grazed a knee. The duty technician who comes up finds three things. The safety key clip, which should be clipped to the runner’s clothing, is kept in a desk drawer because it “keeps coming off by itself,” so the treadmill has been run with the key pushed in and no lanyard. The running belt jerks every time a foot lands, and its edge already rubs the frame on the left side. Behind the towel rack, two treadmills and one stationary bike are plugged into one extension reel whose cable runs under the rear end of a treadmill. The guest is not badly hurt, but the technician has to decide which machines may be used tomorrow morning, what can be done in house, and what waits for the supplier technician.
Scope
This chapter covers fitness equipment in hotels, hospitals, and staff dormitories from the building technician’s side: motorized treadmills, stationary bikes that run on line power and those that generate their own power, and cable weight machines. It covers how the equipment is built, electrical supply and emergency stops, layout, daily and periodic checks, belts and wire ropes, lubrication, records, and how to take equipment out of use. HSE guidance from the United Kingdom on work equipment and fitness center criteria from the United States Department of Defense are written as data from those countries. For electrical work the chapter uses Permenaker 12/2015 (Minister of Manpower Regulation) on electrical occupational safety and health (K3) in the workplace; as of November 2026 JDIH Kemnaker lists it as in force, and Permenaker 11/2026 only revokes provisions on inspectors within it, not the definitions and the division of who does the work that are used here.
Bearings and their signs of damage are in Chapter 4 on rolling and plain bearings, belts and pulleys in Chapter 6 on belts, pulleys, and chains, and lubrication in Chapter 8 on lubrication and tribology. The DC and universal motors that many treadmills use are in Chapter 45 · Electrical & Control, push buttons and emergency stops in Chapter 49 · Electrical & Control, RCD testing in Chapter 18 · Electrical & Control, inspection of portable electrical equipment in Chapter 114 · Electrical & Control, lockout and tagout in Chapter 76 · Electrical & Control, machine vibration and noise in Chapter 14, and maintenance strategy in Chapter 11 · Systems, Diagrams & Diagnosis.
Work outside the building technician’s authority: opening the motor hood and the control board, repairing or replacing boards, motors, and inverters, replacing the running belt, the deck, the drive belt inside the motor compartment, and wire ropes, welding or straightening frames, and any work on the installation and outlets. All of that belongs to the equipment supplier’s technician and to an authorized electrical technician. The building technician checks from the outside, cleans, lubricates and adjusts the parts that the manual leaves to the user, tests the emergency stop, keeps records, takes equipment out of use, and reports.
How treadmills, stationary bikes, and cable weight machines are built
A treadmill is a machine for running in place that uses an endless belt driven by a motor. The running belt turns over two rollers, a driven front roller and an adjustable rear roller. Under the belt lies the deck, a flat board that carries the runner’s weight; the belt slides over it with the help of a lubricant. The drive motor in the motor compartment at the front turns the front roller through a drive belt. A second motor raises the front end to set the incline. The control board under the motor hood converts the supply into the voltage and current that set the motor speed, while the console shows the speed and takes the runner’s commands.
The belt speed equals the surface speed of the roller that drives it, as long as the belt does not slip:
where is the belt speed (m/s), the roller diameter (m), and the roller speed (rpm). The formula assumes the belt is thin compared with the roller diameter. When the belt slips on the roller, the belt speed is lower than the value calculated from the roller speed, and the runner feels it as a jerk when a foot lands.
Stationary bikes come in two groups. A self-powered bike uses a small generator turned by the pedals to power the console and the magnetic brake, so it has no supply cord. A line-powered bike plugs into an outlet, usually because its console is large or because a motor sets the resistance. Pedal resistance comes from an eddy current brake, a magnet next to a metal flywheel that induces eddy currents and a braking force without contact, or from a friction pad pressing on the flywheel on group exercise bikes. The pedal speed is stepped up to the flywheel through one or two stages of belts or chains.
A cable weight machine uses a stack of weight plates that slide on two guide rods. The user selects the load with a selector pin, then pulls a handle connected to the stack through a wire rope, a rope of steel wires twisted into strands, with the strands twisted into a rope. The rope passes over several pulleys and is fixed at its ends with swaged end fittings. The rope tension in a one-to-one arrangement equals the weight of the load:
where is the rope tension (N), the mass of the selected load (kg), and the acceleration due to gravity (9.81 m/s²). When the load is jerked, or dropped and then caught, the momentary tension can be far above this value.
Electrical supply and emergency stops
The treadmill is the largest electrical load in a gym. Its current rises when the motor starts, when the incline is raised, and when a heavy runner walks slowly on a deck that has run dry of lubricant. The United States Department of Defense fitness center criteria call for dedicated circuits for all treadmills and floor outlets whose locations are coordinated with the equipment selected. For a hotel technician, that means one treadmill, one outlet, and one circuit, with no extension reels or splitters. The supply cord must not run under the deck or across a walkway, because a deck that lowers when the incline changes can pinch the cord.
Permenaker 12/2015 defines electrical equipment as an electricity-using item that is a complete unit and can convert electrical energy into another form of energy, so a treadmill falls within it. The regulation also sets out that planning, installation, modification, and maintenance of electrical installations and equipment are done by an Ahli K3 bidang Listrik (licensed electrical safety expert), while installation and maintenance may be done by a Teknisi K3 Listrik (electrical safety technician), a technical worker skilled in electrical K3 and licensed by the Minister. Adding an outlet, moving a circuit, or repairing a floor connection is not work for a building technician without that license.
Inside the motor compartment, the control board stores energy in large capacitors, and some machines still have live parts even after the console switch is off. That is why the building technician does not open the motor hood. The console switch or the power switch on the frame breaks only one pole on some machines, so the way to take a machine out of use is to unplug it and tag it.
A safety key is a magnetic tab or plug that sits on the console and is tied by a lanyard to a clip attached to the runner’s clothing. If the runner slips backward, the lanyard pulls the key off and the belt stops. A key pushed in without a lanyard, or a clip attached to the frame, removes that function. The stop button on the console and the safety key together form the treadmill’s emergency stop (Chapter 49 · Electrical & Control on push buttons and emergency stops).
HSE guidance on work equipment calls for readily accessible emergency stop controls where the risk assessment requires them, operating in priority to the normal stop controls, and not used to stop the equipment during normal operation. The same guidance stresses that an emergency stop is not a substitute for other safeguards. For a treadmill, this means the safety key does not replace the free area behind the machine and a well-kept belt.
Free area, layout, and supervision
A fall from a treadmill is almost always backward, because the belt carries a runner who has lost their footing to the rear end. The free area is the empty space behind and beside the machine that must not be taken up by other equipment, walls, racks, or chairs. Its size comes from the equipment manual, because it depends on deck length and top speed. The technician checks this area every time new equipment arrives or the layout changes, and marks it on the floor when the room is tight.
The United States Department of Defense fitness center criteria also call for the control desk attendant to have direct sight of the free weight area and visual control of the cardio equipment area, treadmills included, either directly or through CCTV, and the desk serves as the focal point for emergencies. A small hotel rarely has a permanent attendant in the gym, so the substitutes used are monitored cameras, a call button, and opening hours that match the duty schedule. These considerations belong in the risk assessment for the room, not in equipment maintenance.
The floor under a treadmill must be level so the frame does not twist. A twisted frame makes the belt keep drifting to one side even after the rear roller has been adjusted. The technician checks the leveling feet and shims when a machine is moved, then checks belt tracking again.
Daily checks, periodic checks, and records
The daily check is done before the room opens, by a trained attendant, with the same checklist every day. For a treadmill, the attendant checks that the safety key and its lanyard are present, runs the belt at low speed, then pulls the key and confirms that the belt stops. The stop button is tested the same way. The belt is checked for being centered, for frayed edges, and for a glazed, slippery surface. The handrails are shaken to find loose bolts.
The cord and plug get the same user check as other portable electrical equipment. HSE lists what to look for: a lead that is frayed, cut, or heavily scuffed, a cracked plug or bent pins, colored wires visible where the lead joins the plug, signs of overheating such as burn marks, and cables trapped under furniture. The last item is the one most often found in a gym, because the cord gets trapped under the end of a treadmill or the foot of a weight machine.
For stationary bikes, the attendant checks the pedals and their straps, the seat and handlebar adjustment pins, and any noise from below when the pedals turn. For cable weight machines, the attendant looks along the visible length of the rope, the pulleys, the end fittings, and the selector pin. A machine that fails any item is taken out of use at once.
Periodic checks follow the equipment manual: running belt tension and tracking, deck lubrication, cleaning under the machine, frame bolt tightness, and a full inspection by the supplier technician. In the United Kingdom, the work equipment regulations require machinery maintenance logs to be kept up to date and inspection results to be recorded and kept until the next inspection. Those regulations apply to equipment used by workers, while equipment provided for use by members of the public, such as fitness equipment for guests, is covered by the general duties of the United Kingdom’s workplace safety act. No Indonesian regulation specific to fitness equipment was found. The sensible practice is to keep records anyway: the date, run hours, the result of the safety key test, findings, and who did the check.
Running belts, drive belts, and wire ropes
A running belt that is too loose slips on the front roller when a foot lands. The slip is felt as a jerk, and at high speed it can make the runner lose their footing. A belt that is too tight adds load to the roller bearings and the motor, so the bearings wear quickly and become noisy (Chapter 4 on rolling and plain bearings). Tension is set with two bolts at the rear end that move the rear roller, following the sequence and the amount of turning in the manual. Both bolts are turned by the same amount so the roller stays parallel.
Belt tracking is the tendency of the belt to stay in the middle of the deck. A belt that keeps drifting to one side is adjusted by turning one rear roller bolt a little at a time while the belt runs slowly. The gap between the rear roller and the belt is an in-running nip, so hands, rags, and wrenches are kept away from the rear end while the belt runs. Tracking adjustment is done only by someone trained on the manual for that machine.
The drive belt inside the motor compartment is cared for like other belts in Chapter 6 on belts, pulleys, and chains, but it sits behind the motor hood. Squealing from the front at start-up or when the incline rises is a sign to report, not to fix in house.
The wire rope on a weight machine is checked along the part that can be seen without dismantling the guards. Signs that the rope must be replaced: broken wires, strands opening up like a birdcage, permanent kinks, flattened sections, rust, a plastic jacket torn through to the wires, and end fittings that have slipped. The pulleys are checked for turning freely, grooves without sharp edges, and flanges without cracks. A rope is never spliced, knotted, or held with an improvised clamp. Replacement uses a rope and end fittings from the equipment supplier at the right length, because a rope that is too long leaves the handle slack and lets the rope jump out of the pulley groove.
Lubricating the deck and moving parts
Friction between the belt and the deck sets the motor current and the heat in the control board. A dry deck makes the motor draw more current, wears the underside of the belt quickly, and makes the control board run hotter. A deck with too much lubricant makes the belt slip and drips lubricant onto the floor. The type of lubricant, the amount, and the interval are set by the equipment manual; some decks use silicone lubricant, while others are factory coated and must not be given any other lubricant. The basis for the choice is in Chapter 8 on lubrication and tribology.
HSE guidance uses bearing lubrication as an example of maintenance that bears on safety: bearings that are not lubricated can seize or overheat and lead to danger. Treadmill roller bearings and bike flywheel bearings are generally sealed and not regreased; noise or heat there is a reason to call the supplier technician. Weight stack guide rods are cleaned and lubricated only with the material named in the manual, because the wrong lubricant holds dust and makes the plates stick.
A lubrication interval stated in run hours is more accurate than a monthly interval, because treadmill use in a hotel differs greatly between busy and quiet seasons. The hour counter on the console is recorded every time the deck is lubricated.
Taking equipment out of use
A machine that fails a check is taken out of use in a way guests cannot misunderstand. The plug is pulled, a “do not use” tag with the date, the reason, and the checker’s name is fixed to the console, and the treadmill’s safety key is held by the attendant. For a weight machine, the selector pin is removed or the handle is tied to the frame. Then the finding is recorded and the supplier technician is contacted. The machine returns to use only after the repair is finished and the daily check has been repeated with a good result.
Tagging at an outlet or electrical panel follows the lockout and tagout procedure in Chapter 76 · Electrical & Control when the work involves the installation. If a machine was involved in an accident, it is not moved, adjusted, or cleaned until management decides, so that its condition can be examined.
Worked example
The numbers in the examples below are practice figures unless their origin is stated.
Example 1: checking belt speed from the outside. A 3.2 m running belt is marked with chalk on its edge. At a display of 6.0 km/h, the attendant counts 20 belt revolutions in 38 s. The belt speed is m/s, which is km/h, about 1 percent above the display. With a roller diameter of 0.065 m, the roller turns at rpm. If the revolution count changes from one measurement to the next at the same display, the belt is probably slipping, and the machine is taken out of use.
Example 2: two treadmills on one circuit. The treadmill nameplate reads 230 V and 10 A. Two treadmills on one 16 A circuit need A, above the circuit rating, before counting the motor starting current and the stationary bike also plugged in. One treadmill draws up to VA. The finding is reported so that an authorized electrical technician can provide a dedicated circuit per treadmill; the extension reel is removed that same day and one treadmill is taken out of use.
Example 3: how many treadmills fit along one wall. The wall is 9.0 m long and the room is 6.0 m deep. The manual calls for 0.5 m beside each treadmill, 2.0 m behind, and 0.3 m in front; each treadmill is 0.9 m wide and 2.1 m long. A row of treadmills needs a width of m, so gives , which means at most 6 treadmills. Seven treadmills would need m. The depth used is m, leaving 1.6 m for a walkway and racks. Racks or other equipment may go in that strip, but not within the 2.0 m behind the treadmills.
Example 4: a lubrication interval by run hours. The manual calls for the deck to be checked and lubricated every 150 run hours. The hour counter read 2,340 hours at the last lubrication and reads 2,468 hours today, so the machine has run hours. The remainder is hours. At 5 hours of use per day, the next lubrication falls due in days, so it is scheduled for the fourth day. A monthly interval would still be late in the busy season, when use doubles.
Example 5: wire rope tension on a weight machine. A selected load of 60 kg in a one-to-one arrangement gives N. The manual gives the rope’s minimum breaking force as 8.0 kN, so the ratio is . If a user drops the load and then catches it and the momentary tension doubles, the ratio falls to . This figure is not used to delay replacement: a rope with broken wires is replaced, whatever the calculation says, because the remaining strength of a damaged rope is unknown.
Example 6: separating noise sources on a stationary bike. The pedals turn at 70 rpm. The first stage uses pulleys of 260 mm to 65 mm, a ratio of , so the intermediate shaft turns at rpm. The second stage is 200 mm to 50 mm, a ratio of 4, so the flywheel turns at rpm, which is Hz. A knock once per pedal revolution has a frequency of Hz and points to the pedal, the crank, or the crank bearing, while an 18.7 Hz hum points to the flywheel (Chapter 14 on condition monitoring). Both are reported with their frequencies.
Stop conditions
- The safety key or its lanyard is missing or damaged, or the belt does not stop when the key is pulled or the stop button is pressed: take the treadmill out of use, unplug it, tag it, and contact the supplier technician.
- The running belt slips or jerks, its edge rubs the frame or is frayed, or the deck is cracked: stop use and hand adjustment or replacement to the supplier technician.
- A burning smell, smoke, sparks, a hot plug, or the treadmill circuit’s MCB or RCD tripping repeatedly: do not switch it on again; unplug it if it is safe to do so, or have a designated person switch it off at the panel, then hand it to an authorized electrical technician and the supplier technician.
- The supply cord is damaged, pinched under the deck, or the machine is plugged into an extension reel: take the machine out of use until an authorized electrical technician provides a suitable outlet and circuit.
- A wire rope with broken wires, kinks, opened strands, a torn jacket, or slipped end fittings, a cracked pulley, or a bent selector pin: stop the weight machine, remove the pin, tag it, and wait for the supplier technician.
- The work would require opening the motor hood or the control board, or replacing the running belt, deck, drive belt, motor, or wire rope: do not let the building technician do it; hand it to the supplier technician.
- A cracked frame, a cracked weld, or handrail and seat bolts that stay loose after being tightened as the manual describes: take the machine out of use and report to the supplier technician.
- A guest or staff member is injured while using a machine: give first aid, do not move or adjust the machine, and report to management before the machine is used again.
Common misinterpretations
Guess what’s wrong first, then open the explanation.
Common misconception
Pushing the safety key in is enough to get the treadmill running.
Why is it wrong?
A key pushed in without a lanyard to the runner’s clothing does not stop the belt when the runner falls. Its function lies in the lanyard that pulls the key off.
Common misconception
The console switch is off, so the motor hood is safe to open.
Why is it wrong?
Some machines are still live and the capacitors store energy after the switch is turned off. The motor hood is not the building technician’s territory; the machine is taken out of use by unplugging it.
Common misconception
The more lubricant, the longer the belt lasts.
Why is it wrong?
Too much lubricant makes the belt slip and drip onto the floor. The type, amount, and interval follow the equipment manual.
Common misconception
A wire rope with just one broken wire is still strong.
Why is it wrong?
The remaining strength of a damaged rope is unknown and the damage grows quickly over the pulleys. A rope with broken wires is replaced.
Common misconception
A drifting belt only needs to be pushed back to the middle.
Why is it wrong?
A drifting belt means the rear roller is not parallel, the frame is twisted, or the deck is worn. The cause is found and adjusted according to the manual by someone trained.
Links to other chapters
Chapter 6 on belts, pulleys, and chains explains the belt tension and tracking used here for the running belt and the drive belt, Chapter 4 on bearings explains roller bearing noise and heat, and Chapter 8 on lubrication explains the choice of lubricant for the deck and guide rods. The electrical supply and cord checks connect to Chapter 18 · Electrical & Control on RCD testing and Chapter 114 · Electrical & Control on inspection of portable electrical equipment, while the safety key is a special form of the emergency stop in Chapter 49 · Electrical & Control.
Exercises and worked solutions
The numbers in the exercises are for practice.
Try to answer first, then open the worked solution.
The attendant finds the safety key clip attached to a treadmill handrail. What is the problem and what is the action?
Check my answer
See the worked solution
A clip attached to the frame will not pull the key off when the runner falls, so the emergency stop does not work. The attendant removes the clip from the frame, explains the correct use to the guest, and records the finding if it happens again.
At a display of 8.0 km/h, a 3.0 m belt makes 30 revolutions in 42 s. What is the belt speed, and what does it mean?
Check my answer
See the worked solution
The belt speed is m/s, which is 7.7 km/h, about 4 percent below the display. The measurement is repeated; if the difference stays or keeps changing, the belt may be slipping and the machine is reported to the supplier technician.
Why does a treadmill need its own circuit when its nameplate says only 10 A?
Check my answer
See the worked solution
Motor starting current, raising the incline, and heavy runners push the current above the usual figure, and other treadmills or other equipment on the same circuit add load. A dedicated circuit prevents trips that stop the belt suddenly and prevents an overheated extension reel.
A staff member wants to open the motor hood to vacuum out dust because of a humming noise. What is the technician’s answer?
Check my answer
See the worked solution
The motor hood covers a control board that stores energy and parts that can stay live, so opening it is the supplier technician’s work. The building technician records the noise, takes the machine out of use if the noise is new or getting louder, and reports.
A weight machine wire rope still has an intact jacket, but two wires stick out near the end fitting. What is the technician’s decision?
Check my answer
See the worked solution
Broken wires are a sign that the rope must be replaced, even with an intact jacket, because damage near an end fitting can spread quickly. The machine is stopped, the selector pin is removed, and the supplier technician replaces the rope with the correct spare part.
Why is a deck lubrication interval better stated in run hours?
Check my answer
See the worked solution
Treadmill use in a hotel rises and falls with the season, so a monthly interval can be too infrequent in the busy season and too frequent in the quiet season. Run hours follow actual wear, and the hour counter on the console makes them easy to record.
References
External sources
- Safe use of work equipment. Provision and Use of Work Equipment Regulations 1998. Approved Code of Practice and guidance, L22 (Fourth edition)hse.gov.uk
- UFC 4-740-02 Fitness Centers (3 February 2019, Change 1, 30 May 2019)wbdg.org
- Maintaining portable electric equipment in low-risk environments, INDG236(rev3)hse.gov.uk
- Peraturan Menteri Ketenagakerjaan Nomor 12 Tahun 2015 tentang Keselamatan dan Kesehatan Kerja Listrik di Tempat Kerjajdih.kemnaker.go.id
Revision history
| Date | Version | Change |
|---|---|---|
| November 14, 2026 | 1 | First published |
How to cite
Kurnia (2026). Hotel fitness equipment: treadmills and stationary bikes, electrical supply and emergency stops, daily checks, belts and wire ropes, lubrication, and limits of work. ARSTEMA Academy. Revised November 14, 2026. arstema.com/en/academy/konsep/peralatan-kebugaran-hotel-treadmill-dan-sepeda-statis-kelistrikan-dan-stop-darurat-pemeriksaan-harian-sabuk-dan-kabel-baja-pelumasan-serta-batas-pekerjaan
Self-check · 3 questions
Check your understanding before moving on
Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.
The attendant finds the safety key clip attached to a treadmill handrail. What is the problem and what is the action?
At a display of 8.0 km/h, a 3.0 m belt makes 30 revolutions in 42 s. What is the belt speed, and what does it mean?
Why does a treadmill need its own circuit when its nameplate says only 10 A?
Nearby chapters
Reading order by shelf: Mechanical & Mechatronics · Chapter 18.
Reading order by shelf: Mechanical & Mechatronics · Chapter 16.
Another chapter in Mechanical & Mechatronics.