Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Mechanical & Mechatronics · Chapter 18Applied

    By Kurnia · Published November 14, 2026 · Version 1 · 21 min read

    Automatic fences and gates and barrier gates

    motors and drives, safety sensors, crushing and impact hazards, manual release, periodic maintenance, and limits of work

    The sliding gate at a hotel’s goods entrance closes on a delivery worker’s trolley, its pressure sensitive edge is torn, its photo sensor has been taped over because it keeps reopening in the rain, and the barrier gate in front of the lobby comes down on a motorcyclist who was following a car. This chapter covers sliding gates, swing gates, and barrier gates from the building technician’s side: motors, gears, and limit switches, the kinetic energy of a gate leaf, crushing, shearing, and impact points up to a height of 2.5 m, force amplification near the hinge, force limitation with basic limits of 400 N for crushing and 1,400 N for impact, pressure sensitive edges and photo sensors and their limitations, barrier gate arm tip speed and separating pedestrian routes, manual release from the point of view of when and who, periodic maintenance and records, and the changes that turn an installer into a manufacturer. HSE guidance from the United Kingdom is written as data from that country, and Permenaker 12/2015 is used for the division of electrical work. Setting forces and controller parameters, measuring forces, repairing motors and controllers, and changing safety devices are the work of a competent gate contractor and an authorized electrical technician.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    One morning at a hotel’s goods entrance, a 6 m wide sliding gate closes while a delivery worker is still pushing a trolley through it. The trolley is trapped between the gate edge and the post, and the gate stops only after pushing the trolley a few centimeters. The technician who is called finds the rubber edge at the end of the gate torn, and one of the photo sensors on the post taped over by a security guard because “the gate keeps opening by itself when it rains.” In the same week, the barrier gate in front of the lobby comes down onto the helmet of a motorcyclist following a guest’s car. Neither incident causes serious injury. The technician’s decision that day is when the gate and the barrier gate stay automatic, when they are run under supervision, and when they are taken out of use.

    Scope

    This chapter covers powered sliding gates, swing gates, and barrier gates at hotels, hospitals, laundries, and parking garages from the building technician’s side: how the motors and drives are arranged, crushing, shearing, and impact hazards, force limitation and safety sensors, barrier gates and pedestrians, manual release, periodic maintenance, records, and limits of work. This chapter is learning material for understanding gates and recognizing dangerous conditions, not a work instruction for adjusting or repairing gates. HSE guidance from the United Kingdom, United Kingdom workplace regulations, and the European standards they refer to are written as data from those countries. No Indonesian rule specific to powered gates was found; for electrical work the chapter uses Permenaker 12/2015 (Minister of Manpower Regulation) on electrical occupational safety and health (K3) in the workplace, which as of November 2026 JDIH Kemnaker lists as in force, and Permenaker 11/2026 only revokes provisions on inspectors within it.

    Risk assessment, interlocks, and the performance level of safety control systems are in Chapter 70 · Electrical & Control on functional safety of machinery. Motors and their controls are in Chapter 42 · Electrical & Control on single-phase motors and capacitors and Chapter 43 · Electrical & Control to Chapter 58 · Electrical & Control, especially Chapter 47 · Electrical & Control on motor protection, Chapter 49 · Electrical & Control on push buttons and emergency stops, Chapter 51 · Electrical & Control on control logic and interlocks, and Chapter 55 · Electrical & Control on motor braking. Photoelectric sensors are in Chapter 59 · Electrical & Control, access control and card readers in Chapter 94 · Electrical & Control, lockout and tagout in Chapter 76 · Electrical & Control, and gravity and spring energy in Chapter 4 · Safety on isolation of non-electrical energy.

    Work outside the building technician’s authority: setting force, speed, automatic closing time, and controller parameters, measuring closing forces, fitting, adjusting, moving, or replacing pressure sensitive edges, photo sensors, and limit switches, repairing motors, gears, barrier gate springs, and controllers, and adding automatic functions or fitting a motor to a manual gate. All of that belongs to a competent gate contractor, and work on the electrical circuit belongs to an authorized electrical technician. The building technician never bypasses, jumpers, covers, or removes safety sensors, pressure sensitive edges, or force limiters, under any circumstances. The building technician checks and tests functions as the user instructions describe, keeps records, operates the manual release when designated and trained, takes the gate out of automatic use, and reports.

    Gates, barrier gates, and their drives

    A sliding gate is a gate leaf that moves in a straight line parallel to the fence, running on a floor track or hanging from rollers on one side. Its motor turns a small gear that engages a toothed rack along the leaf. A swing gate turns on hinges and is driven by a motor arm beside the leaf or by a motor under the ground. A barrier gate is a long boom that turns about 90 degrees at the end of a drive housing, usually balanced by a spring so that a small motor is enough to raise it.

    The drive is generally a single-phase motor with a capacitor or a low-voltage DC motor, a worm gear that reduces speed and holds the leaf when it stops, and a controller that takes commands from a remote, a push button, a card reader, or a loop detector in the road. The ends of travel are detected by limit switches or a revolution counter. Some drives measure motor current to detect an obstruction; this method is a kind of force limitation, discussed below.

    A moving gate leaf stores kinetic energy:

    E=12mv2E = \tfrac{1}{2} m v^2

    where EE is the kinetic energy (J), mm the mass of the leaf (kg), and vv the speed of the leaf (m/s). This energy has to be absorbed by something when the leaf stops, either by the motor and brake or by an object or person who is trapped. Speed appears squared, so slowing the leaf near the end of travel is far more effective than adding rubber.

    Gates and barrier gates also store other energy. A barrier gate spring stays tensioned even when the power is off. A gate on a slope can roll on its own when its drive is released, and a close-boarded swing gate leaf can be pushed by the wind. These hazards are covered in Chapter 4 · Safety on isolation of non-electrical energy.

    Crushing, shearing, and impact hazards

    HSE lists the hazards of powered gates: being hit by the moving leaf, crushed between fixed and moving parts, trapped between those parts, caught on moving parts such as gears, electrocuted, and harmed by hydraulic or pneumatic parts. Because most gates are outdoors, the weather adds hazards: the leaf can fall or be blown over, rotate uncontrollably around its hinges, run off its track, and water getting into the cabling and control boxes can cause an electric shock or make the gate fail to operate safely.

    The extract from European standard EN 12453:2001 in an HSE safety notice treats a hazard point as existing up to a height of 2.5 m above the floor, including at the main closing edge and its opposing edge, between leaves passing each other, between the leaf and fixed parts nearby, at gaps in the leaf that change size during movement, and at the drive parts. A crushing point is a place where two surfaces close in on each other until they press on the body. A shear gap is a place where two edges pass each other, for example the bars of a sliding gate passing close to the fence bars or a post.

    The death of a nine-year-old child in the United Kingdom in 2010 shows a crushing point that is not obvious. The gap between the spine of a swing gate leaf and a brick pillar was 160 mm with the gate closed and narrowed to 110 mm with the gate fully open; the child reached through the gap to press the exit button on the inside. The motor current sensors did not work because of the forces near the hinge, and the photo sensor between the pillars had been fitted only to detect vehicles.

    Near the hinge, force is amplified. The same moment that the motor arm produces at the leaf edge produces a much larger force at a point close to the pivot:

    Fr=FeLrF_r = F_e \frac{L}{r}

    where FeF_e is the force at the leaf edge (N), LL the distance from the leaf edge to the hinge (m), rr the distance from the crushing point to the hinge (m), and FrF_r the force at the crushing point (N). The formula assumes a rigid leaf and a constant motor moment over that instant. HSE notes that forces measured as the standards specify are amplified closer to the pivot, and that one child’s death in 2006 was partly attributed to the design of the hinge area.

    Type of use in that standard divides gates into three groups: type 1 is used only by trained users with no public access, type 2 is used by a limited group of trained people but sits in a public area, and type 3 can be operated by anyone and is in contact with the public. A hotel gate opened by a loop detector or a guest button is type 3, and a goods gate operated by security staff but passed by delivery workers and pedestrians is at least type 2.

    Force limitation and safety sensors

    Force limitation is a function that stops and reverses the leaf when the force on an obstruction exceeds a limit. The 2018 HSE safety notice states that the revised standards keep the existing force limits, basically 400 N for crushing and 1,400 N for impact. Those limits are maximum forces, not targets: HSE calls for impact and crushing forces as low as possible and verified by testing after installation. HSE also notes research suggesting that those maximum limits may not be appropriate for children.

    Force measurement uses special measuring equipment in the hands of a competent person; without that equipment, according to HSE, no one can be sure the gate meets the standards. HSE takes the view that force limitation on its own is unlikely to be reliable enough to prevent a person from being trapped, so automatic type 2 and type 3 gates need additional safeguards. The most effective safeguard together with force limitation is a pressure sensitive edge, a rubber profile on the closing edge containing a switch or sensor that triggers a stop and reverse when it is pressed. Photo sensors, when correctly installed and configured, are another option, but HSE’s analysis shows that one or two beams do not guarantee that a person is detected.

    Most photo sensors on gates are designed to prevent the gate from closing on a vehicle. HSE writes that these beams are usually not high-integrity safety devices, need to be made less sensitive to rain and leaves, and are easily stepped over. This is why the tape on the sensor in the opening case is dangerous: a sensor that keeps false-triggering is a symptom to report, not a reason to disable it. A loop detector in the road detects the metal of a vehicle, not a person.

    The control system decides whether these devices really work together. HSE gives an example: a category 2 controller delivers only a category 2 safety system even if the other components are category 3, and wrong connections can lower it further, because category 2 requires a fault in the safety function to be detected no later than the end of the next movement. HSE also calls for the safety function to be checked before each movement where the technology permits. Categories and performance levels are covered in Chapter 70 · Electrical & Control on functional safety of machinery.

    Barrier gates and pedestrian routes

    Barrier gates are among the products covered by the European standards for doors, gates, and barriers primarily for vehicular use. Their main hazard differs from that of a sliding gate. The tip of the arm moves fastest, because the speed of every point on the arm is proportional to its distance from the pivot:

    v=ωLv = \omega L

    where vv is the speed of a point on the arm (m/s), ω\omega the angular speed (rad/s), and LL the distance from that point to the pivot (m). A 4 m arm that comes down in a short time makes its tip move fast enough to injure a head, while the part near the drive housing becomes a crushing point against the housing.

    A barrier gate is usually set to come down once the loop detector no longer senses a vehicle. A motorcycle following a car may not be detected by some detectors and arrives under the arm just as the arm comes down. A pedestrian cutting through the barrier gate lane is not detected at all. United Kingdom workplace guidance calls for vehicles to be separated from pedestrians by a kerb or barrier at doorways and gateways, with separate pedestrian routes and clear marking. For a hotel technician, the follow-up is to report pedestrians and motorcycles using the barrier gate lane, so that management can provide separate routes.

    The barrier gate’s balancing spring stores energy even with the motor off, and an arm that is broken or has come loose from its mounting can move unexpectedly. An arm that is bent, cracked, or loose in its mounting is taken out of use, and the building technician does not touch the spring.

    Manual release and emergencies

    United Kingdom workplace regulations require powered gates to have suitable and effective features to prevent injury by trapping, and, where necessary for safety, to be operable by hand unless they open automatically if the power fails. The accompanying code of practice adds that any tools needed for manual opening should be readily available at all times, and that the person opening the gate by hand should not be put at risk if the power is restored while the gate is being opened.

    A manual release is a mechanism that disconnects the drive from the leaf, usually with a special key and lever, so the leaf can be moved by hand. HSE states that automatic gates must have an emergency release mechanism in case someone is trapped, and that release keys and release instructions should be readily available to all authorized users. Gate owners are asked to have the maintenance contractor show them how to release the gate in an emergency, which should be easy and quick, and to tell staff or other users.

    For a hotel, the decision is about when and who, not about how to dismantle the drive. The manual release is used in three situations: a person or vehicle is trapped and the gate has already stopped, the power has failed and the gate needs to be opened, or the gate has been taken out of automatic use and needs to be opened under supervision. The person who operates it is someone whose name is on the list, who has been shown how by the contractor, and who is present on every shift, for example the security supervisor and the duty technician. The release key is kept in a place every duty officer knows, not in the contractor’s drawer.

    There are three things to think about before the leaf is released. The drive’s power is isolated first, so the gate does not move if the power comes back. A gate on a slope can roll and a swing leaf can be pushed by the wind as soon as the drive is released, so a second person holds the leaf. After the emergency is over, the drive is re-engaged and the gate is tested by the contractor or a trained person before it returns to automatic mode.

    Periodic maintenance, records, and modifications

    HSE calls for forces to be periodically re-measured as part of the planned preventive maintenance schedule, and for all safety devices to be checked regularly according to the manufacturer’s instructions, on a schedule agreed by those managing the gate and their maintenance company. Building owners are asked to make sure maintenance is done by a reputable company that tests the safety features with force measuring equipment, and to keep a maintenance log.

    United Kingdom workplace guidance includes powered doors among its examples of equipment that needs a system of maintenance. The building technician’s check follows the user instructions for that gate. It generally means seeing that the pressure sensitive edge is intact and firmly fitted, the photo sensor lenses are clean and uncovered, the track is free of stones and rubbish, the leaf is not leaning, the hinges and stops are not loose, the gear guards are in place, the signs are legible, and the control box is closed and dry. Any function test named in the user instructions, for example the gate reversing when a beam is broken, is done with a test object, not with the body, and the result is recorded.

    A gate believed to be unsafe is switched off or used only under direct supervision, for example with hold-to-run control, until the contractor makes it safe. Hold-to-run control is a mode that moves the leaf only while a button is held and stops it when the button is released; its operator needs a clear view of the whole movement of the leaf.

    Anyone working on a gate is responsible for leaving it in a safe condition, including switching off and isolating the power if the gate has to be left in an unsafe condition. Modification is not maintenance work, and substantial modifications may require reassessment. Fitting a motor to a manual gate makes the installer the manufacturer of a new machine with all the conformity assessment duties. Raising the force setting so the gate can push against the wind, disabling a sensor that keeps false-triggering, or adding automatic closing are all modifications that change the safety level of the gate.

    The electrical parts of a gate come under the electrical K3 rules. Permenaker 12/2015 sets out that installation and maintenance of electrical installations and equipment are done by a licensed Ahli K3 bidang Listrik (electrical safety expert) or Teknisi K3 Listrik (electrical safety technician). A control box with water inside, stripped cables, or a burning smell from the drive housing are reported, and the building technician does not open them.

    Worked example

    The numbers in the examples below are practice figures unless their origin is stated.

    Example 1: reading a force test report. The contractor’s report for a hotel sliding gate records peak forces at the closing edge at three heights: 310 N, 380 N, and 455 N. The basic crushing limit is 400 N, so the third point exceeds the limit by 455−400=55455 - 400 = 55 N. The building technician adjusts nothing. The gate is moved to hold-to-run mode under supervision, the report is passed to management, and the contractor is asked to correct and re-measure before the gate returns to automatic operation.

    Example 2: leaf energy and speed. A 450 kg sliding gate leaf moves at 0.25 m/s. Its energy is E=0.5×450×0.252=14.1E = 0.5 \times 450 \times 0.25^2 = 14.1 J. If all of that energy were absorbed by a rubber edge compressed by 30 mm, the average force would be 14.1/0.03=46914.1 / 0.03 = 469 N, above 400 N, before counting the motor’s push. At 0.15 m/s the energy is 0.5×450×0.152=5.060.5 \times 450 \times 0.15^2 = 5.06 J and the average force is 5.06/0.03=1695.06 / 0.03 = 169 N. The model is rough, but it shows why slowing down near the end of travel is part of safety, and the setting belongs to the contractor.

    Example 3: force near the hinge. A 3.0 m swing gate leaf presses with 150 N at its edge. At a point 0.25 m from the hinge, the same moment produces Fr=150×3.0/0.25=1,800F_r = 150 \times 3.0 / 0.25 = 1{,}800 N. That figure is 12 times the force at the edge and far above 400 N, so the hinge area is protected by design and fixed guards, not by force limitation. The technician reports any gap in the hinge area that a hand or head can enter.

    Example 4: a narrowing gap. In the 2010 incident, the gap between the leaf spine and the pillar was 160 mm when closed and 110 mm when fully open. The gap narrowed by 160−110=50160 - 110 = 50 mm, which is 50/160=3150/160 = 31 percent. The lesson for inspection: gaps are measured with the gate closed, half open, and fully open, because a gap that is safe in one position can become a crushing point in another. A button that can be reached from outside through a gap is reported.

    Example 5: the barrier gate arm tip and a motorcycle. A 4.0 m barrier gate arm comes down 90 degrees in 2.0 s. Its angular speed is ω=(π/2)/2.0=0.785\omega = (\pi/2)/2.0 = 0.785 rad/s, so the tip of the arm moves at 0.785×4.0=3.140.785 \times 4.0 = 3.14 m/s, while a point 1.0 m from the pivot moves at only 0.79 m/s. A motorcycle following 1.5 m behind a car at 10 km/h, which is 10/3.6=2.7810/3.6 = 2.78 m/s, arrives under the arm in 1.5/2.78=0.541.5/2.78 = 0.54 s. That time is far shorter than the time the arm takes to come down, so the rider is under the arm as it comes down; a separate motorcycle lane is the answer.

    Example 6: wind and the force setting. A close-boarded swing gate leaf measuring 1.8 m by 2.0 m is struck by a 15 m/s wind. The dynamic pressure is q=0.5×1.2×152=135q = 0.5 \times 1.2 \times 15^2 = 135 Pa, the area is 1.8×2.0=3.61.8 \times 2.0 = 3.6 m², and the wind force is about 135×3.6=486135 \times 3.6 = 486 N. That force is larger than the 400 N crushing limit. If the motor often stops in strong wind, raising the force setting would make the gate press on a person with the same force; this situation is reported to the contractor for a reassessment of the design.

    Stop conditions

    1. A person or vehicle is trapped by the gate or barrier gate: stop the movement with the emergency stop or the power switch, call for medical help, and let the designated, trained person release the leaf with the manual release after the drive’s power has been isolated.
    2. The pressure sensitive edge is torn or detached, a photo sensor is not working, or the gate does not stop and reverse when tested with a test object as the user instructions describe: take the gate out of automatic mode, use it only under direct supervision or switch it off, and contact the gate contractor.
    3. A sensor is found covered, jumpered, removed, or moved, or the force and speed settings have been changed by someone not authorized: do not run it in automatic mode; report to management and hand the restoration to the gate contractor.
    4. The leaf is off its track or leaning, hinges or stops are loose, gears are unguarded, or the barrier gate arm is bent, cracked, or loose: switch it off, cordon off the area of movement, and contact the gate contractor.
    5. Water in the control box, stripped cables, a burning smell, or a shock when touching the frame: do not open the control box; have a designated person isolate it at the panel and hand it to an authorized electrical technician.
    6. The manual release is needed but the release key or its instructions are missing, or the person present has not been trained: do not pry open or dismantle the drive; call the designated person, the gate contractor, or the emergency services.
    7. There is a request to raise the force, disable a sensor that keeps false-triggering, add automatic closing, or fit a motor to a manual gate: stop that plan and hand it to a competent gate contractor for reassessment.
    8. Children play near the gate, or pedestrians and motorcycles routinely use the vehicle lane and the barrier gate: report to management for a review of the risk assessment and separation of routes.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    The gate already has a motor current sensor, so it is sure to stop if it hits someone.

    Why is it wrong?

    HSE judges force limitation on its own not reliable enough, and near the hinge the force is amplified until the current sensor does not work. A gate in a public area needs a pressure sensitive edge or presence detection in addition.

    Common misconception

    A photo sensor that keeps false-triggering may be covered for a while.

    Why is it wrong?

    Covering the sensor removes a safeguard without replacing it. False triggering is a symptom of a dirty lens, a shifted position, or a design that needs review, and it is reported to the contractor.

    Common misconception

    400 N is a safe force.

    Why is it wrong?

    That figure is the maximum limit in the standard, not a target, and HSE calls for forces as low as possible because that limit may not be appropriate for children.

    Common misconception

    Only the contractor needs to know about the manual release.

    Why is it wrong?

    The manual release is used when a person is trapped or the power fails, when the contractor is not there. The designated person on every shift needs to know when to use it and where the key is.

    Common misconception

    Fitting a motor to an old gate is just electrical work.

    Why is it wrong?

    A motorized gate becomes a new machine, and its installer takes on the manufacturer’s duties, including the risk assessment and the safety devices.

    Chapter 70 · Electrical & Control on functional safety of machinery explains the categories and performance levels that decide whether gate sensors and controllers work reliably. The motors, contactors, motor protection, and emergency stops of gate drives are covered in Chapter 43 · Electrical & Control to Chapter 58 · Electrical & Control, photoelectric sensors in Chapter 59 · Electrical & Control, and the card readers and remotes that open gates in Chapter 94 · Electrical & Control on access control. Barrier gate spring energy and gravity on sloping gates connect to Chapter 4 · Safety on isolation of non-electrical energy, and isolating power before the manual release is used connects to Chapter 76 · Electrical & Control on safe work and LOTO.

    Exercises and worked solutions

    The numbers in the exercises are for practice.

    Try to answer first, then open the worked solution.

    1. A security guard tapes over the photo sensor on the goods gate because the gate keeps opening by itself in the rain. What is wrong and what does the technician do?

      Check my answer
      See the worked solution

      The photo sensor is one of the gate’s safeguards, and covering it lets the gate close on a person or vehicle without detecting them. The technician removes the tape so the sensor works again, moves the gate to supervised use until the contractor has checked the cause of the false triggering, and reports to management.

    2. A force test report records peak forces of 360 N, 395 N, and 420 N. What is the building technician’s decision?

      Check my answer
      See the worked solution

      The 420 N point exceeds the basic 400 N limit, so the gate is not used in automatic mode until it has been corrected and re-measured. The building technician does not adjust the force, because setting and measuring forces require measuring equipment and the contractor’s competence.

    3. A 2.5 m swing gate leaf presses with 120 N at its edge. What is the force at a point 0.2 m from the hinge, and what does it mean?

      Check my answer
      See the worked solution

      The force is 120×2.5/0.2=1,500120 \times 2.5 / 0.2 = 1{,}500 N, 12.5 times the force at the edge. The hinge area cannot be protected by force limitation, so the gaps there are protected by design and fixed guards, and any open gap is reported.

    4. The power fails at night and an ambulance needs to enter through a hospital’s sliding gate. Who opens it and what is considered first?

      Check my answer
      See the worked solution

      The person who opens it is the designated duty officer who has been trained by the contractor, using a release key kept in a known place. Before releasing, the drive’s power is isolated so the gate does not move if the power returns, and a second person holds the leaf if the road slopes or the wind is strong.

    5. Building management wants to add 30 seconds of automatic closing to a gate that security staff have always operated with a hold-to-run button. What is the technician’s answer?

      Check my answer
      See the worked solution

      Automatic closing changes the gate from hold-to-run control with an operator who watches the movement into an automatic gate, so the type of use and the safeguards needed change. The request is handed to the gate contractor for reassessment, including pressure sensitive edges and presence detection.

    6. A 3.5 m barrier gate arm comes down 90 degrees in 1.5 s. What is its tip speed, and what is the follow-up?

      Check my answer
      See the worked solution

      The angular speed is (π/2)/1.5=1.05(\pi/2)/1.5 = 1.05 rad/s, so the tip of the arm moves at 1.05×3.5=3.681.05 \times 3.5 = 3.68 m/s. A speed that high can injure a head, so the technician checks whether pedestrians and motorcycles use the barrier gate lane and reports the need for separate routes.

    References

    External sources

    • The basicshse.gov.uk
    • Ensuring powered doors and gates are safehse.gov.uk
    • Risks to pedestrians from crushing zones on electrically powered gateshse.gov.uk
    • Risks to pedestrians from crushing zones on electrically powered gates - 2hse.gov.uk
    • Powered perimeter gateshse.gov.uk
    • Revision of Standards for Powered Doors, Gates and Barriershse.gov.uk
    • Workplace health, safety and welfare. Workplace (Health, Safety and Welfare) Regulations 1992. Approved Code of Practice and guidance, L24 (Second edition)hse.gov.uk
    • Equipment and machinery frequently asked questions (FAQs)hse.gov.uk
    • Peraturan Menteri Ketenagakerjaan Nomor 12 Tahun 2015 tentang Keselamatan dan Kesehatan Kerja Listrik di Tempat Kerjajdih.kemnaker.go.id

    Revision history

    DateVersionChange
    November 14, 20261First published

    How to cite

    Kurnia (2026). Automatic fences and gates and barrier gates: motors and drives, safety sensors, crushing and impact hazards, manual release, periodic maintenance, and limits of work. ARSTEMA Academy. Revised November 14, 2026. arstema.com/en/academy/konsep/pagar-dan-gerbang-otomatis-serta-palang-parkir-motor-dan-penggerak-sensor-keselamatan-bahaya-jepit-dan-tabrak-pembuka-manual-perawatan-berkala-serta-batas-pekerjaan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A security guard tapes over the photo sensor on the goods gate because the gate keeps opening by itself in the rain. What is wrong and what does the technician do?

    2

    A force test report records peak forces of 360 N, 395 N, and 420 N. What is the building technician’s decision?

    3

    A 2.5 m swing gate leaf presses with 120 N at its edge. What is the force at a point 0.2 m from the hinge, and what does it mean?

    Self-assessment progress0%

    Nearby chapters