Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Electrical & Control · Chapter 116Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 21 min read

    Audiovisual equipment in meeting rooms and ballrooms

    projectors and LED screens, wireless microphones and frequencies, mixers and amplifiers, signal and power cables, suspended loads, and event preparation

    Two hours before a reception in a hotel ballroom, the host’s wireless microphone keeps dropping out, the loudspeakers hum, and a vendor crew member proposes cutting the grounding pin off the amplifier plug to get rid of the hum, while a truss carrying loudspeakers and lights already hangs above the dance floor. This chapter covers audiovisual equipment in meeting rooms and ballrooms from the building technician’s side: the system chain; projectors and screens and LED walls, with their illuminance, contrast, power, and weight; wireless microphones, with wavelength, channel spacing, and intermodulation; mixers and amplifiers, with ground hum and ventilation; signal and power cables, with voltage drop; suspended loads; and event preparation. It is based on UK HSE guidance on electricity at places of entertainment and on event safety. The frequency bands that wireless microphones may use in Indonesia cannot yet be confirmed. Connecting to fixed distribution boards, installing hanging points, and raising suspended loads are work for authorized parties.

    Section you’re reading: Chapter opening

    Two hours before a wedding reception for 600 guests in a hotel ballroom, the host tests the wireless microphone and the sound drops out every time they walk to the side of the stage. The loudspeakers hum softly, and a crew member from the sound vendor proposes cutting the grounding pin off the amplifier plug because “the hum always goes away when the ground is removed”. Above the dance floor, an aluminum truss carrying four loudspeakers already hangs from two points in the ceiling, and a power cable runs across the front of the side exit door. The building technician who is called in has to be able to separate sound-quality problems from safety problems.

    Scope

    This chapter covers event audiovisual equipment in hotel meeting rooms and ballrooms from the building technician’s side: projectors, LED walls, wireless microphones, mixers and amplifiers, cables, suspended loads, and event preparation. This is learning material, not a work instruction. The chapter contains no steps for opening equipment, working on live parts, connecting cables to fixed distribution boards, installing hanging points, or raising loads.

    Building sound systems and emergency announcements are covered in Chapter 109 on building sound and paging systems, data cabling and WiFi in Chapter 108 on hotel data networks, inspection of portable equipment and vendor extension leads in Chapter 114 on inspecting portable electrical equipment, and slings and safe working loads in Chapter 9 · Safety on lifting loads with equipment. Work at height is in Chapter 10 · Safety, lighting quantities in Chapter 105 on building lighting, voltage drop in Chapter 28, RCD testing in Chapter 18, and power supply for exhibitions in Chapter 117 on temporary power for events and exhibitions.

    Outside the building technician’s authority: providing new circuits, connecting vendor cables to fixed distribution boards, opening amplifier racks or LED walls, installing hanging points, raising and lowering suspended trusses, and assigning radio frequencies. That work belongs to the hotel’s authorized electrician, sound and lighting contractors, competent riggers, and the building’s structural designer. The building technician prepares the power points that are available, checks what is visible, calculates, stops dangerous situations, and reports.

    The audiovisual system chain in event spaces

    An event audiovisual system consists of two chains. The audio chain starts at the sound sources, namely wired microphones, wireless microphones, or music players, then goes into the mixing console, which is the device that sets the level, tone, and routing of each source, and then to the power amplifier, which raises the signal to a power that can drive the loudspeakers. Many event loudspeakers have built-in amplifiers, so each loudspeaker needs its own power supply. The video chain starts at a laptop or player, passes through a video signal switcher, and goes to a projector or LED wall.

    The two chains are connected by signal cables and supplied by power cables, often from several different receptacles. The UK HSE guidance GS50 for places of entertainment notes that the mixing desk is sometimes placed far from the amplifiers and linked by multi-core signal cables, and that amplifier output terminals, loudspeaker wiring, and loudspeaker connectors can carry dangerous voltages. This means loudspeaker cables are treated as power cables: their insulation and connectors suit their voltage and current.

    This division gives a map of responsibilities: sound and picture quality are the vendor operator’s concern, while power cables, circuit loads, cable routes, suspended objects, and exit routes are the building’s concern because they affect the safety of guests and staff.

    Projectors, screens, and LED walls

    A projector emits luminous flux onto a screen, and the manufacturer usually rates it in lumens. The flux spreads over the screen surface, so the average illuminance on the screen is

    Ep=ΦAE_\text{p} = \frac{\Phi}{A}

    where EpE_\text{p} is the illuminance from the projector (lux), Φ\Phi is the luminous flux reaching the screen (lumens), and AA is the picture area (m²). This formula assumes all the flux falls evenly on the picture, so the result is an upper limit. What decides whether the picture is legible is its ratio to the room light falling on the screen, EaE_\text{a}:

    C=Ep+EaEaC = \frac{E_\text{p} + E_\text{a}}{E_\text{a}}

    where CC is the contrast ratio (dimensionless). The white parts of the picture receive Ep+EaE_\text{p} + E_\text{a}, while the black parts receive only EaE_\text{a}. For this reason, dimming the lights that shine on the screen often helps more than adding lumens.

    An LED video wall is a screen made of panels of LED modules that emit their own light, so it does not depend on a dark room. From the building’s side, an LED wall is a large electrical load, a heat source, and a heavy mechanical load. The manufacturer’s data sheet gives the maximum power, average power, and weight per square meter. Maximum power is used to choose circuits because a full white picture draws the largest current; average power is used to estimate the heat that the air conditioning must remove. Single-phase and three-phase currents are calculated with

    I1=PUcos⁡φ,I3=P3 ULLcos⁡φI_1 = \frac{P}{U\cos\varphi}, \qquad I_3 = \frac{P}{\sqrt{3}\,U_\text{LL}\cos\varphi}

    where I1I_1 is the current on a single-phase supply (A), I3I_3 is the current per phase on a balanced three-phase supply (A), PP is the active power (W), UU is the phase-to-neutral voltage (V), ULLU_\text{LL} is the line-to-line voltage (V), and cos⁡φ\cos\varphi is the power factor from the data sheet.

    Projectors and amplifiers both need air; intake and exhaust openings covered by decorative fabric or packing boxes make the equipment hot and can become a fire source. The HSE guidance for entertainers notes that high-power amplifiers can get very hot if their ventilation is blocked, for example by equipment stacked on or near them, and that the amplifier’s thermal protection can shut the system down in the middle of a performance.

    Wireless microphones and frequencies

    A wireless microphone is a microphone that sends its audio signal to a receiver by radio waves on a particular carrier frequency. Each transmitter needs its own frequency, and its receiver is tuned to the same frequency. Its wavelength follows the general wave relationship

    λ=cf\lambda = \frac{c}{f}

    where λ\lambda is the wavelength (m), cc is the speed of electromagnetic waves, 3.00×1083.00 \times 10^{8} m/s, and ff is the frequency (Hz). At hundreds of megahertz the wavelength is tens of centimeters, so human bodies, metal trusses, and LED walls are large enough to block the signal; receivers are placed with a clear view of the stage.

    Transmitters whose frequencies are too close interfere with each other. FM radio broadcasting, for example, is allowed 100 kHz on each side of its carrier frequency; wireless microphones also occupy a certain bandwidth, and the minimum channel spacing is set by the receiver manufacturer. When several transmitters operate together, circuits that are not perfectly linear also create new frequencies from their combinations. The strongest is third-order intermodulation, a new frequency at

    fIM=2f1−f2f_\text{IM} = 2f_1 - f_2

    where f1f_1 and f2f_2 are the frequencies of two transmitters operating at the same time. Each pair of channels gives two products, 2f1−f22f_1 - f_2 and 2f2−f12f_2 - f_1. A third channel that falls on one of those products will hiss or drop out, so a frequency list is drawn up by calculating all the intermodulation products.

    The more common causes of dropouts are simpler: a weak transmitter battery, a covered receiver antenna, too much distance, or a microphone in the next meeting room using the same frequency. The hotel records the frequencies of each room and those of vendors so that two events do not clash.

    The frequency bands that wireless microphones may use in Indonesia, their transmit power limits, and whether their use requires a license or equipment certificate cannot yet be confirmed as of November 2026; check with the ministry responsible for communications and digital affairs, and ask the vendor to show the equipment certificate and the basis for the frequencies they use. The frequencies in the worked examples do not indicate permitted bands.

    Mixers, amplifiers, and ground hum

    Line-powered audio equipment must be double insulated or correctly fitted with protective grounding, and problems arise when many devices are connected together. The shields of signal cables, that is, the metal braid inside audio cables, and the protective grounding conductor of each device can form a ground loop, which is a closed path through more than one ground connection. The small current flowing in that loop is heard as line hum, which is a low sound at the line frequency and its multiples.

    HSE states that hum must not be cured by removing protective grounding; removing grounds is one of the common causes of entertainers receiving electric shocks, some of them fatal, and a hand-held item such as a microphone can become live without the person holding it being able to let go. The same guidance gives the safe routes: good equipment should not hum, sometimes the shield of an interconnecting audio cable needs to be disconnected at one end only, some equipment has a facility to separate the signal ground from the safety ground without affecting safety, and supplying all the sound equipment from the same receptacle or distribution panel goes a long way to reducing interference. Equipment whose line connections are in doubt is checked by an electrically competent person, because an audio expert is not necessarily an expert in electrical safety.

    An amplifier draws more power than it sends to the loudspeakers, and the difference becomes heat in the rack:

    Pin=Poutη+P0P_\text{in} = \frac{P_\text{out}}{\eta} + P_0

    where PinP_\text{in} is the input power from the line (W), PoutP_\text{out} is the average output power to the loudspeakers (W), η\eta is the amplifier efficiency (dimensionless), and P0P_0 is the idle power with no signal (W). The average output power of music is far below the rated power; amplifier loads on the building’s 100 V line are in Chapter 109.

    GS50 also states that stage lighting circuits should be kept separate from circuits used for audio equipment, and that the hoists for lighting bars are supplied by a separate circuit. This separation reduces dimmer noise in the sound system.

    Signal cables and power cables

    Signal cables carry small voltages that are easily disturbed. A balanced audio cable uses two conductors and one shield, so interference that enters is equal on both conductors and cancels out at the receiver. Because power cables create magnetic fields, signal routes are kept apart from power routes and crossed at right angles when necessary.

    GS50 asks for several habits with event power cables: extension leads are fully unwound from their drums to avoid overheating, multiple-socket strips are used instead of adapters stacked in wall receptacles, damaged leads are taken out of service at once, and the line, neutral, and ground connections in extension leads must be correct because a wrong connection can leave the equipment working but lethal. A cable that is still coiled heats itself because the heat from the inner layers cannot escape.

    Long cables also reduce the voltage at their far end. For a single-phase circuit with copper conductors, the voltage drop at the load current is

    ΔU=2 ρ L IA\Delta U = \frac{2\,\rho\,L\,I}{A}

    where ΔU\Delta U is the voltage drop (V), ρ\rho is the resistivity of copper, about 0.0178 Ω mm2/m0.0178\ \Omega\,\text{mm}^2/\text{m} at 20 °C as in Chapter 18, LL is the one-way cable length (m), II is the current (A), and AA is the conductor cross-sectional area (mm²). The factor 2 represents the outgoing and return conductors. The limits are covered in Chapter 28 on voltage drop; a cable that is too small for its current also gets hot.

    Cables on the floor make people trip. HSE advises routing cables to minimize tripping hazards and mechanical damage, positioning cable connections with care, and using cable ramps or similar protectors where cables cross walkways. In a ballroom, cables run along the walls, under the stage, or over supports above, and exit doors and their routes stay free of unprotected cables.

    GS50 advises places of entertainment to provide enough power and receptacles, including industrial-type receptacles for large demands, which in the UK are typically rated 16 A, 32 A, 63 A, or 125 A. The guidance also forbids bypassing circuit protective devices if the supply does not meet the demand of the lighting and sound installation; the right course is to provide sufficient power. In a hotel, large power points for events are provided by the authorized electrician. Receptacles used by portable equipment and performers’ equipment should be protected by 30 mA RCDs, and an RCD that trips is a sign of a fault that must not be ignored. RCD testing is covered in Chapter 18.

    Suspended loads: trusses, loudspeakers, lights, and screens

    Objects suspended above guests are the greatest hazard in an event space. HSE notes that loudspeaker clusters and lighting can weigh up to 500 kg and are often suspended 6 m or more above the ground. Suspended LED walls can be heavier still.

    For suspended equipment, HSE gives basic rules. Every light fitting or suspended item is fitted with a safety chain or safety wire. The weight of the equipment does not exceed the safe working load of its securing points. No suspended equipment, including lighting bars and amplification equipment, relies solely on one suspension cable, clamp, or bolt; each means of suspension is secured to independent fixing points on the equipment and on the structure. GS50 adds that light fittings and electrical equipment must not be suspended from their flexible cable alone. While people work overhead, the area below is cleared and loose items are tied off so that they cannot fall.

    The load per hanging point is calculated from the total weight and how it is shared:

    Fpoint=k mtotal gnF_\text{point} = k\,\frac{m_\text{total}\,g}{n}

    where FpointF_\text{point} is the force on one hanging point (N), mtotalm_\text{total} is the total mass of the truss and its contents (kg), gg is the gravitational acceleration, 9.81 m/s², nn is the number of points sharing the load equally, and kk is an uneven-sharing factor set by the rigger. The result is compared with the safe working load of the hanging point in the building’s structural data. A load concentrated at one end makes one point carry more than the average; sling angles and asymmetric loads are covered in Chapter 9 · Safety.

    Lifting equipment such as chain hoists and their accessories is thoroughly examined by a competent person; in the UK, unless there is another examination scheme, the interval is 6 months for lifting accessories and equipment used to lift people, and 12 months for other lifting equipment, and an examination is also made after assembly and before use at each location for equipment that has to be assembled or installed. Requirements for lifting equipment in Indonesia are covered in Chapter 9 · Safety. For outdoor structures, HSE warns that equipment designed for indoor use generally does not account for wind loading and easily overturns to the rear or sides.

    Event preparation

    Preparation starts before the vendor arrives. The building technician receives the event plan: the layout, the equipment list and its power, the microphone frequencies, the objects to be suspended, and the build and strike schedule. The technician adds up the load per circuit, matches it against the available power points, and reports any shortfall to the authorized electrician before the event day.

    During the build, the technician checks without opening any equipment: cables and plugs intact, extension leads fully unwound, amplifier ventilation clear, cable routes protected, exit doors and exit signs not covered, and the building’s evacuation loudspeakers not covered by event equipment. HSE advises users to visually inspect equipment that is moved around, especially before it is used at a new location, and to take out of service any equipment that is damaged or trips an RCD.

    The sound check also concerns hearing safety. For audiences at music events in the UK, HSE recommends that the A-weighted equivalent continuous sound level over the event not exceed 107 dB and the C-weighted peak not exceed 140 dB in any part of the audience area, that the audience not be within 3 m of a loudspeaker where practical, and under no circumstances closer than 1 m. Workplace noise for staff is covered in Chapter 7 · Safety on noise and vibration.

    Dismantling is treated as seriously as the build: suspended loads are lowered by the crew that installed them with the area below cleared, equipment is switched off before cables are unplugged, and damage to the building’s receptacles is recorded for repair.

    Worked example

    The numbers in the examples below are practice numbers unless their origin is stated.

    Example 1: projector and ballroom lights. A 6,000-lumen projector lights a picture 4 m by 2.25 m, that is, A=4×2.25=9A = 4 \times 2.25 = 9 m², so Ep=6,000/9=667E_\text{p} = 6{,}000/9 = 667 lux. With the ballroom lights fully on, the light falling on the screen is 200 lux and C=(667+200)/200=4.3C = (667 + 200)/200 = 4.3. After the lights above the screen are switched off and the guest lighting is dimmed until the light on the screen is 50 lux, C=(667+50)/50=14.3C = (667 + 50)/50 = 14.3. With the hotel AV team’s target contrast of at least 7, the first condition fails and the second passes.

    Example 2: power and heat of an LED wall. An LED wall 6 m by 3.5 m, that is, 6×3.5=216 \times 3.5 = 21 m², with a maximum power of 600 W/m² and an average power of 200 W/m² from the data sheet, draws at most 600×21=12,600600 \times 21 = 12{,}600 W. On single phase at 230 V with a power factor of 0.95, the current is I1=12,600/(230×0.95)=57.7I_1 = 12{,}600/(230 \times 0.95) = 57.7 A. If the hotel limits the load on a 16 A circuit to 12.8 A, 57.7/12.8=4.557.7/12.8 = 4.5 circuits are needed, rounded up to 5 circuits. On a 400 V three-phase supply, I3=12,600/(3×400×0.95)=19.1I_3 = 12{,}600/(\sqrt{3} \times 400 \times 0.95) = 19.1 A per phase. The average heat to the room, 200×21=4,200200 \times 21 = 4{,}200 W, is passed on to the air-conditioning operator.

    Example 3: checking a frequency list. Three microphones operate at 520.0 MHz, 520.6 MHz, and 521.5 MHz. The third-order intermodulation products are 2×520.0−520.6=519.42 \times 520.0 - 520.6 = 519.4, 2×520.6−520.0=521.22 \times 520.6 - 520.0 = 521.2, 2×520.0−521.5=518.52 \times 520.0 - 521.5 = 518.5, 2×521.5−520.0=523.02 \times 521.5 - 520.0 = 523.0, 2×520.6−521.5=519.72 \times 520.6 - 521.5 = 519.7, and 2×521.5−520.6=522.42 \times 521.5 - 520.6 = 522.4 MHz. None falls on a channel in use; the closest is 521.2 MHz, which is 521.5−521.2=0.3521.5 - 521.2 = 0.3 MHz from the third channel. If a fourth microphone is proposed at 521.2 MHz, that channel falls exactly on 2f2−f12f_2 - f_1 and will be disturbed. The wavelength at 520 MHz is λ=3.00×108/(520×106)=0.577\lambda = 3.00 \times 10^{8}/(520 \times 10^{6}) = 0.577 m.

    Example 4: amplifier rack. A rack holds four 1,000 W amplifier channels. The operator estimates the average output power during music at one eighth of the rated power, so Pout=4×1,000/8=500P_\text{out} = 4 \times 1{,}000/8 = 500 W. With an efficiency of 0.70 and an idle power of 60 W, Pin=500/0.70+60=774P_\text{in} = 500/0.70 + 60 = 774 W, and at 230 V with a power factor of 0.90 the current is 774/(230×0.90)=3.7774/(230 \times 0.90) = 3.7 A. The heat in the rack is about 774−500=274774 - 500 = 274 W, so the back of the rack is left open.

    Example 5: power cable to the stage. The stage is supplied by a 40 m extension lead carrying 12 A. With 2.5 mm² conductors, ΔU=2×0.0178×40×12/2.5=6.84\Delta U = 2 \times 0.0178 \times 40 \times 12/2.5 = 6.84 V, that is, 6.84/230=3.06.84/230 = 3.0 percent. With 1.5 mm² conductors, ΔU=2×0.0178×40×12/1.5=11.4\Delta U = 2 \times 0.0178 \times 40 \times 12/1.5 = 11.4 V, that is, 5.0 percent. A better choice is a power point closer to the stage.

    Example 6: truss above the dance floor. An 8 m truss with a mass of 7 kg/m carries four 45 kg loudspeakers and 24 kg of cables and clamps, so mtotal=8×7+4×45+24=260m_\text{total} = 8 \times 7 + 4 \times 45 + 24 = 260 kg. On two hanging points with a sharing factor of 1.25 from the rigger, Fpoint=1.25×260×9.81/2=1,594F_\text{point} = 1.25 \times 260 \times 9.81/2 = 1{,}594 N, equivalent to 1,594/9.81=162.51{,}594/9.81 = 162.5 kg per point. The structural data record a safe working load of 250 kg for the ceiling point, so even sharing is still below it. If one point carries 70 percent because the loudspeakers are moved to one end, its load is 0.7×260=1820.7 \times 260 = 182 kg before the factor and is recalculated before the truss is raised.

    Stop conditions

    1. The protective grounding of equipment has been removed, or removal is proposed, to get rid of hum, for example a ground pin cut off or an adapter without ground in use: stop using that equipment; it is only powered again after it has been checked by the authorized electrician, and the hum is dealt with by the vendor’s sound coordinator without touching the protective grounding.
    2. Someone feels tingling when holding a microphone or touching a metal truss, or an RCD trips repeatedly when a particular item is plugged in: stop using that item, do not reset the RCD again and again, and hand it over to the authorized electrician according to Chapter 114 and Chapter 18.
    3. Suspended equipment has no second safety chain or safety wire, relies on a single clamp or its flexible cable, or its hanging point has no safe working load data: do not raise the load and clear the area below; the decision is made by a competent rigger together with the building manager according to Chapter 9 · Safety.
    4. The work requires climbing to the ceiling, a truss, or a tall ladder without suitable access and fall protection: stop; the work is continued by a trained crew with access according to Chapter 10 · Safety.
    5. The power demand exceeds the available power points, or the vendor asks for their cable to be connected directly to a fixed distribution board: do not connect and do not add adapters; the hotel’s authorized electrician provides suitable power points.
    6. Unprotected cables cross an evacuation route, or equipment covers exit doors, exit signs, or the building’s evacuation loudspeakers: the event does not start until the vendor clears them on the order of the hotel’s event manager, and the evacuation loudspeakers are checked according to Chapter 109.
    7. An amplifier, projector, or LED wall smells of burning, smokes, or is very hot because its ventilation is blocked: disconnect its supply only from a switch or receptacle if it is safe, keep people away, and follow the building’s fire procedure according to Chapter 17 · Buildings & Facilities.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    The hum goes away when the ground is removed, so that is the fix.

    Why is it wrong?

    Removing protective grounding removes protection against electric shock and has killed entertainers. Hum is dealt with through the arrangement of signal cable shields, a signal-ground separation facility designed by the manufacturer, or supply from a single panel.

    Common misconception

    A brighter projector always improves the picture.

    Why is it wrong?

    Contrast is decided by the ratio of projector light to room light on the screen, so dimming the lights above the screen is often more effective.

    Common misconception

    Microphone frequencies are safe as long as they are far apart.

    Why is it wrong?

    Several transmitters create intermodulation products at 2f1−f22f_1 - f_2 and 2f2−f12f_2 - f_1. A channel that falls on such a product is disturbed even if it looks far from the other channels.

    Common misconception

    An extension lead may be used coiled if the distance is short.

    Why is it wrong?

    A cable that is still coiled cannot shed its heat. The cable is fully unwound from the drum so that it can carry its rated current without overheating.

    Common misconception

    The truss hangs from two points, so each carries half.

    Why is it wrong?

    Load sharing depends on where the items sit; a load concentrated at one end makes one point carry more than half.

    Chapter 109 on building sound systems covers the fixed sound system and emergency announcements; this chapter covers event equipment that comes and goes. Vendor cables and equipment follow Chapter 114 on portable electrical equipment, suspended loads follow Chapter 9 · Safety on lifting loads, and generators and temporary distribution boards follow Chapter 117 on temporary power for events and exhibitions.

    Exercises and worked solutions

    The numbers in the exercises are for practice.

    Try to answer first, then open the worked solution.

    1. A 5,000-lumen projector lights a picture 3 m by 1.7 m, and the room light falling on the screen is 120 lux. What is the illuminance from the projector and the contrast ratio?

      Check my answer
      See the worked solution

      The picture area is 3×1.7=5.13 \times 1.7 = 5.1 m², so Ep=5,000/5.1=980E_\text{p} = 5{,}000/5.1 = 980 lux. The contrast is C=(980+120)/120=9.2C = (980 + 120)/120 = 9.2, enough for the target of 7 in Example 1, and it will fall if the room lights are raised.

    2. An LED wall 4 m by 2.5 m with a maximum power of 500 W/m² is supplied from single phase at 230 V with a power factor of 0.95. What is its current, and how many 16 A circuits are needed if the circuit load is limited to 12.8 A?

      Check my answer
      See the worked solution

      The power is 500×10=5,000500 \times 10 = 5{,}000 W and the current is 5,000/(230×0.95)=22.95{,}000/(230 \times 0.95) = 22.9 A. With a limit of 12.8 A per circuit, 22.9/12.8=1.822.9/12.8 = 1.8 circuits are needed, rounded to 2 circuits, which the authorized electrician provides.

    3. Two microphones operate at 610.0 MHz and 610.4 MHz. The vendor proposes a third microphone at 610.8 MHz. What is the technician’s assessment?

      Check my answer
      See the worked solution

      The intermodulation product of the two microphones is 2×610.4−610.0=610.82 \times 610.4 - 610.0 = 610.8 MHz, exactly on the proposed channel. That channel will hiss or drop out when the other two channels are active, so the vendor is asked to choose another frequency that is recalculated and whose basis of use can be shown.

    4. During the sound check the loudspeakers hum and the crew proposes using an adapter without a ground pin on the mixer. What does the building technician do?

      Check my answer
      See the worked solution

      The technician refuses the adapter, because removing protective grounding removes shock protection and has killed entertainers. The crew is asked to deal with the ground loop, for example by supplying all the sound equipment from one panel or by using a manufacturer-designed signal-ground separation.

    5. A 60 kg loudspeaker hangs from a truss by a single clamp and without a safety wire. What is the action?

      Check my answer
      See the worked solution

      The loudspeaker relies on a single clamp, whereas every suspended item must have independent means of suspension and a safety chain or wire. The area below is cleared, and no one stands under that loudspeaker until a rigger fits a second means of suspension and a proper safety wire.

    6. A 25 m cable reel with a 1.5 mm² cross-section is used still coiled to supply a 10 A load. What is the voltage drop, and what is the other problem?

      Check my answer
      See the worked solution

      The voltage drop is 2×0.0178×25×10/1.5=5.932 \times 0.0178 \times 25 \times 10/1.5 = 5.93 V, that is, 2.6 percent of 230 V. The more dangerous problem is heat: a coiled cable cannot shed its heat and can catch fire, so the cable is fully unwound from the reel.

    References

    External sources

    • Electrical safety at places of entertainment (Guidance Note GS50, fourth edition)hse.gov.uk
    • Electrical safety for entertainers (INDG247(rev2))hse.gov.uk
    • Electrical safetyhse.gov.uk
    • Outdoor equipment to support speaker clusters, lights etchse.gov.uk
    • Common work at height tasks at eventshse.gov.uk
    • Thorough examinations and inspections of lifting equipmenthse.gov.uk
    • Noisehse.gov.uk
    • University Physics Volume 2, 16.5 The Electromagnetic Spectrumopenstax.org

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Audiovisual equipment in meeting rooms and ballrooms: projectors and LED screens, wireless microphones and frequencies, mixers and amplifiers, signal and power cables, suspended loads, and event preparation. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/peralatan-audio-visual-ruang-rapat-dan-ballroom-proyektor-dan-layar-led-mikrofon-nirkabel-dan-frekuensi-mixer-dan-amplifier-kabel-sinyal-dan-daya-beban-gantung-serta-persiapan-acara

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated
    1

    A 5,000-lumen projector lights a picture 3 m by 1.7 m, and the room light falling on the screen is 120 lux. What is the illuminance from the projector and the contrast ratio?

    2

    An LED wall 4 m by 2.5 m with a maximum power of 500 W/m² is supplied from single phase at 230 V with a power factor of 0.95. What is its current, and how many 16 A circuits are needed if the circuit load is limited to 12.8 A?

    3

    Two microphones operate at 610.0 MHz and 610.4 MHz. The vendor proposes a third microphone at 610.8 MHz. What is the technician’s assessment?

    Self-assessment progress0%

    Nearby chapters