Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Electrical & Control · Chapter 115Applied

    By Kurnia · Published November 15, 2026 · Version 1 · 18 min read

    Outdoor lighting on hotel grounds

    street lights and garden lights, poles and foundations, underground cables, grounding and RCDs, timers and photocells, IP protection ratings, and maintenance

    After a night of heavy rain at a resort hotel, the RCD of the garden lighting circuit on the path to the villas trips every time the lights come on at dusk, one bollard light is full of water, the car park lights are still on in the middle of the day, and a light pole in the guest drop-off area leans after being nudged by a shuttle bus. This chapter covers outdoor lighting on hotel grounds from the building technician’s side: types of outdoor luminaire, the illumination level for yards and roads in the annex of Permenaker 5/2018 compared with the car park criteria for United States military facilities, uniformity and nuisance light, poles and foundations, underground cables and the danger of digging near them according to HSE guidance, voltage drop on long circuits, grounding and RCDs in wet places, photocells and astronomical timeclocks, IP codes and water, and maintenance and work limits. British and United States data are written as data from those countries. This chapter gives no steps for live work or for opening the junction box behind a pole access door; that work belongs to an authorized electrician.

    Section you’re reading: Chapter opening

    After a night of heavy rain, the duty technician at a resort hotel receives four reports at once. The RCD of the garden lighting circuit on the path to the villas trips every time the lights come on at dusk, so the path is dark when guests walk back from the restaurant. One bollard light on that path has cracked glass and is full of water. The car park lights in front of the lobby are still on at eleven in the morning, and a light pole in the guest drop-off area is visibly leaning after being nudged by a shuttle bus. The landscaping contractor is also due to dig planting holes along the path tomorrow morning, yet the cable route drawing cannot be found. The technician needs to sort out what they can handle themselves, what is made safe and reported, and what only an authorized electrician may touch.

    Scope

    This chapter covers outdoor lighting within the grounds of hotels, resorts, and hospitals from the building technician’s side: entrance road and car park lighting, garden and footpath lighting, poles and their foundations, underground cables, grounding and RCDs, photocells and timers, IP codes, and maintenance and work limits. Public street lighting outside the hotel’s boundary belongs to the local government and is not covered. Data from British guidance and from United States military facilities are written as data from those countries. Workplace illumination levels for Indonesia are taken from Permenaker 5/2018 (Minister of Manpower Regulation), which as of November 14, 2026 is recorded as in force in the JDIH Kemnaker database.

    Photometric quantities and the lumen method are in Chapter 33 on lighting installations and Chapter 105 on building lighting. Grounding is in Chapter 29, TN and TT systems in Chapter 20, RCD testing in Chapter 18, and RCD types and the locations where RCDs must be installed in Chapter 22. Laying underground cables according to PUIL is in Chapter 30 on installing wiring systems, voltage drop in Chapter 28, surges and lightning in Chapter 35, the meaning of the IP code digits in Chapter 41 on advanced motor data and Chapter 71 on control panel design, LOTO in Chapter 76, and work at height in Chapter 10 · Safety.

    Work outside the building technician’s authority: live work of any kind; opening a pole access door and the junction box inside it, a garden light junction box, or the outdoor lighting panel; replacing a connected driver, photocell, or timer; measuring insulation resistance, loop impedance, and RCD trip time; installing or moving underground cables; assessing the strength of poles and foundations; and digging near cables. The electrical work belongs to an authorized electrician, pole assessment to a structural engineer or the pole manufacturer, and digging to a contractor with a work permit. The building technician patrols at night, records lights that are out or on during the day, inspects from the outside, cleans parts that can be reached from the ground, presses the RCD test button when assigned, puts up barriers, and reports. An RCD that has tripped is not bridged, and it is not replaced with a less sensitive RCD.

    Outdoor luminaires, illumination levels, and nuisance light

    Hotel outdoor lighting uses street and area lights on tall poles for entrance roads and car parks, short-pole garden lights, bollard lights, which are post-shaped luminaires from knee to waist height along a path, floodlights for facades and trees, and in-ground lights set into the ground and aimed upward.

    The annex of Permenaker 5/2018 lists an illumination intensity of 20 lux for yards and roads and 5 lux for emergency lighting. Those figures are workplace standards, so they apply where parking attendants, security staff, and gardeners work; the table gives one intensity figure without distinguishing average and minimum points. The design criteria for United States military facilities give car park figures with a different purpose: a minimum horizontal illuminance of 2 lux at grade, a minimum vertical illuminance of 1 lux at a height of 1,524 mm in the center of the drive lane, and a maximum horizontal uniformity of 20 to 1 between maximum and minimum values. Uniformity is checked with

    U=EmaxEmin,Eavg=1N∑i=1NEiU = \frac{E_\text{max}}{E_\text{min}}, \qquad E_\text{avg} = \frac{1}{N}\sum_{i=1}^{N} E_i

    where EmaxE_\text{max}, EminE_\text{min}, and EavgE_\text{avg} are the maximum, minimum, and average illuminance (lux) from NN measuring points EiE_i. The light meter is placed at ground level on a fixed grid of points so that results can be compared over time. Poor uniformity means that guests coming out of a bright area cannot see steps or the pool edge in a dark area.

    Light trespass is glare from a source that is bright compared with its dark surroundings, which according to the same criteria is usually caused by floodlights without control. Those criteria call for area luminaires with no upward light (U0 rating) and a glare rating no higher than G1, and ask that unshielded luminaires mounted low, such as wall packs and decorative luminaires, be limited in brightness to a source of 4,200 lumens or less. At a hotel, light entering guest room windows often comes from floodlights that the gardeners have turned to make them “wider.”

    Poles and foundations

    A light pole stands on a base plate bolted to anchors in a concrete foundation, or is set directly into the foundation. The part that deteriorates fastest is the pole base at ground level, where water and damp soil meet; rust there cannot be seen from a distance and thins the pole wall. Loose anchor nuts, cracks in the concrete foundation, and eroded soil around it also make a pole sway. The building technician’s inspection is visual from the ground: plumb or leaning, rust or holes at the base, anchor nuts and covers complete, the pole access door closed and locked, and the luminaire and its arm not displaced.

    Poles beside vehicle roads are at risk of being hit. The criteria for United States military facilities call for poles near vehicle traffic to have bases designed to break away when struck, while poles not designed that way are protected by a barrier or mounted on one. A pole that has been nudged can look almost plumb yet be damaged at the base or foundation, so a new lean is treated as damage until assessed by an expert. The lean is calculated from the horizontal offset of the top from vertical:

    θ=arctan⁡xH\theta = \arctan\frac{x}{H}

    where θ\theta is the angle of lean (degrees), xx the horizontal offset of the top (m), and HH the pole height (m). The offset is measured from the ground and recorded at every inspection, so that what is assessed is its change.

    Replacing old lamps with LEDs also affects the pole. The same criteria note that replacement LED luminaires have a different weight and effective projected area, and that reduced weight at the top most often increases wind-induced vibration; vibration dampers are designed together with the pole manufacturer or a structural engineer.

    Underground cables and digging near them

    Garden lights and pole lights are generally supplied by underground cables from the outdoor lighting panel, and the route often crosses gardens that are later replanted or dug up for irrigation pipes. HSE guidance in Great Britain explains that injuries from underground cables are usually caused by the explosive effects of arcing current and fire when a live cable is penetrated by the point of a tool or crushed until its conductors touch; the injuries are typically severe burns to the hands, face, and body, while electric shock is less likely. Cables, connections, and terminations that are damaged but left unreported can also cause incidents later.

    The same guidance states that most underground cables are laid in trenches 450 mm to 1 m deep, but depths must never be assumed because cables can be found shallower, and in most cases there is no permanent marker at the surface. A hum detector is a cable locator that picks up the magnetic field from a cable carrying current, and HSE notes that it does not respond to cables with little or no current flowing, for example street lighting cables in the daytime. A signal transmitter connected to or placed near the cable is more accurate, and a cable is positively located only when it has been safely exposed. HSE also advises that hand-held power tools for breaking up hard surfaces be used no closer than 500 mm to the indicated line of the cable, after which the cable is located by careful hand digging.

    For that reason, the as-built drawings of the cable routes are kept and updated whenever the garden changes. Digging near a cable route, including planting holes and event tent stakes, goes under a work permit; the contractor locates cables with suitable equipment, and the building technician does not energize a circuit just so that a cable can be detected. A cable that has been scraped or cut is not touched; the area is made safe and the circuit is isolated by an authorized electrician.

    Garden lighting circuits are often long. For a single-phase circuit with the load assumed to be concentrated at the end, the voltage drop is roughly

    ΔU=2ρLIA\Delta U = \frac{2 \rho L I}{A}

    where ΔU\Delta U is the voltage drop (V), ρ\rho the resistivity of copper, about 0.01750.0175 Ω·mm²/m, LL the one-way cable length (m), II the current (A), and AA the conductor cross-section (mm²). This formula ignores reactance and assumes the whole load is at the end, so the result is an upper bound; voltage drop limits are in Chapter 28 on voltage drop.

    Grounding and RCDs in wet places

    Metal poles, metal bollard bodies, and outdoor panel frames are exposed conductive parts connected to the protective conductor, so an insulation fault produces a fault current that operates the protective device, rather than a voltage on metal touched by a guest (Chapter 20 on grounding systems).

    HSE advises using an RCD whenever possible, particularly in wet or damp locations such as outdoors, because an RCD rated at no more than 30 mA limits the energy in a particular type of electric shock and can save a life. An RCD does not protect against every type of electric shock, so circuits are still securely isolated before they are worked on; RCDs are tested regularly by pressing the test button and making sure the RCD trips, faulty RCDs are removed from use, and RCDs rated above 30 mA provide very limited protection against electric shock.

    An RCD that trips after rain is a signal, not a nuisance to be worked around. Common causes in outdoor lighting are water in junction boxes or inside luminaires, damaged and wet underground cable insulation, flooded connections behind a pole access door, and a total protective conductor current from LED drivers that is too large for one RCD. Chapter 22 on RCDs notes that a 30 mA RCD may trip on a sinusoidal residual current between 15 mA and 30 mA, and recommends that the total protective conductor current downstream of one RCD not exceed 30 percent of its rated residual operating current:

    ∑kIleak,k≤0.30 IΔn\sum_{k} I_{\text{leak},k} \le 0.30\,I_{\Delta\text{n}}

    where Ileak,kI_{\text{leak},k} is the protective conductor current of luminaire kk (mA) and IΔnI_{\Delta\text{n}} the rated residual operating current of the RCD (mA). Finding the cause of a trip requires insulation resistance and leakage current measurements by an authorized electrician after the circuit has been isolated. The building technician records the time of the trip, the weather, and any lights containing water, because those records narrow the search.

    Photocells and timers

    A photocell is a device that measures the illuminance level and switches the luminaire on or off at a preset level; ideally it is set so that the luminaires come on before sunset and go off after sunrise. The criteria for United States military facilities ask that photocells be diligently maintained. A photocell that is dirty, covered by leaves, or lit by another lamp switches lights on too early, switches them off in the middle of the night, or leaves them on during the day.

    An astronomical timeclock is a timer that knows the date and geographic location so that its on and off times follow sunrise and sunset throughout the year. The same criteria give a control strategy for car parks: on and off by an astronomical timeclock or by a photocell, with automatic dimming to 30 percent within 15 minutes after business closes and back to full within 15 minutes before business opens. Timers are not used to switch off all outdoor lighting if the building is still regularly occupied after official hours. A hotel operates all night, so dimming quiet paths is more appropriate than switching off, and the decision belongs to management together with security.

    Photocells for LEDs are chosen to withstand driver inrush current. Those criteria call for photocells meeting a 10 kV and 10 VA rating for LED luminaires, and a seven-pin receptacle on street and car park lights that accepts a standard three-pin photocell or a shorting cap, so that a wireless control node can be fitted later. For surge protection, the same criteria call for surge protective devices at the panel for all outdoor lighting circuits and integral surge protection in LED luminaires, as well as a fuse in the pole base or splice box for street and area lights. A timer whose backup power runs out during a long outage can lose its time, so the lights’ switching times are checked after an outage.

    IP codes and water

    An IP code is an enclosure protection code whose first digit states protection against solid objects and dust, and whose second digit states protection against water. The meaning of each digit and how to choose it from environmental influences are in Chapter 41 and Chapter 71. On hotel grounds, water conditions vary: pole lights get rain from above, bollard lights get spray from garden sprinklers and terrace mopping water, in-ground lights can be submerged in puddles after rain, and poolside lights are exposed to pool water and its chemicals.

    An IP code is a property of the enclosure as tested. Cracked glass, hardened gaskets, missing cover screws, cable glands that do not match the cable, or extra drilled holes reduce protection to the weakest point, as discussed in Chapter 71. Outdoor luminaires also “breathe”: the air inside expands when the lamp is on and contracts when it is off and cool, drawing in moist air or water through gaps, so condensation collects even when rain does not enter directly. Water inside a luminaire speeds up corrosion of terminals and drivers and becomes a leakage path that trips the RCD. For that reason, the IP code and material of a replacement luminaire are matched to the conditions of its location, for example an enclosure declared by its manufacturer as suitable for submersion for in-ground lights on a path that often floods.

    Maintenance and work limits

    Maintenance starts with the night patrol: the technician walks the entrance road, car park, and garden paths, records lights that are out, flickering, or dim using the pole number from the as-built drawings, and in the morning records lights that are still on. Light meter measurements at fixed points are made periodically and when there are complaints.

    Cleaning luminaire glass that can be reached from the ground, trimming low branches that cover luminaires or photocells, and removing items that cover bollard lights are light maintenance; luminaires on tall poles are reached with access for work at height after the circuit has been isolated. Permenaker 12/2015 states that planning, installation, modification, and maintenance of electrical installations are carried out by an Ahli K3 bidang Listrik (electrical occupational safety and health expert), and installation and maintenance may be carried out by a Teknisi K3 Listrik (licensed electrical safety technician), either within the company or at a PJK3 (occupational safety and health services company). For that reason, opening pole access doors, garden light junction boxes, and the outdoor lighting panel, and replacing drivers and photocells, are done by an authorized electrician after isolation and verification of the absence of voltage according to Chapter 76.

    The route from the building’s emergency exits to the assembly point often passes through gardens and car parks, so lights out on that route are reported with priority; emergency lighting is covered in Chapter 106. Damage to many drivers and photocells at once after a thunderstorm is recorded as a single event and checked together with the surge protection at the panel.

    Worked example

    The figures in the examples below are practice figures unless their origin is stated.

    Example 1: reading car park measurements. Six measuring points in the car park in front of the lobby read 3.0, 12, 30, 18, 1.5, and 9.5 lux. The average is Eavg=(3.0+12+30+18+1.5+9.5)/6=74/6=12.3E_\text{avg} = (3.0 + 12 + 30 + 18 + 1.5 + 9.5)/6 = 74/6 = 12.3 lux, and the uniformity is U=30/1.5=20U = 30/1.5 = 20. That uniformity is exactly at the United States limit of 20 to 1, but the minimum point of 1.5 lux is below 2 lux, and the average is far below the 20 lux figure in the Permenaker 5/2018 annex for yards and roads, where the parking attendant’s post is located. The dark points are marked on the drawing and reported to the lighting designer.

    Example 2: the pole nudged by the bus. A 6.0 m pole had a top offset of 0.03 m at last month’s inspection, and after being nudged it is 0.15 m. Its angle is now θ=arctan⁡(0.15/6.0)=1.43\theta = \arctan(0.15/6.0) = 1.43 degrees, and the offset has increased by 0.15−0.03=0.120.15 - 0.03 = 0.12 m in a single event. The sudden change matters more than the size of the angle: the area around the pole is fenced off to a distance equal to the pole height, and the pole and its foundation are assessed by a structural engineer or the pole manufacturer.

    Example 3: voltage drop on a garden path. Twenty bollard lights of 15 W each with a power factor of 0.9 draw I=20×15/(230×0.9)=1.45I = 20 \times 15/(230 \times 0.9) = 1.45 A. With a 2.5 mm² copper cable 150 m long and the load assumed at the end, ΔU=2×0.0175×150×1.45/2.5=3.05\Delta U = 2 \times 0.0175 \times 150 \times 1.45/2.5 = 3.05 V, which is 3.05/230×100=1.33.05/230 \times 100 = 1.3 percent. If the load is evenly distributed, the drop is about half, so a dim furthest light is more likely caused by a corroded connection, which is checked by an authorized electrician.

    Example 4: protective conductor current on one RCD. Forty LED luminaires each leak 0.5 mA, so the total is 40×0.5=2040 \times 0.5 = 20 mA on one 30 mA RCD. The recommended limit in Chapter 22 is 0.30×30=90.30 \times 30 = 9 mA, so the circuit already exceeded it before the rain. After rain, an additional 6 mA of leakage from wet insulation brings the total to 26 mA, inside the 15 to 30 mA band in which the RCD may trip. The solution is to divide the circuit, for example into three groups of at most 9/0.5=189/0.5 = 18 luminaires each, designed by an authorized electrician; replacing the RCD with a 100 mA one is not a solution.

    Example 5: energy and dimming. Thirty entrance road luminaires of 60 W each are on for 12 hours a night, that is, 30×60×12/1,000=21.630 \times 60 \times 12/1{,}000 = 21.6 kWh. If the luminaires are dimmed to 30 percent for 6.5 hours after midnight, the energy is 30×60×(5.5+0.3×6.5)/1,000=13.4130 \times 60 \times (5.5 + 0.3 \times 6.5)/1{,}000 = 13.41 kWh, a saving of 21.6−13.41=8.1921.6 - 13.41 = 8.19 kWh a night or 8.19×365=2,9898.19 \times 365 = 2{,}989 kWh a year. Conversely, six car park luminaires left on during the day for an extra 12 hours for 10 days because of a faulty photocell use 6×60×12×10/1,000=43.26 \times 60 \times 12 \times 10/1{,}000 = 43.2 kWh for nothing.

    Example 6: planting holes near a cable route. The landscaping contractor plans to break up the footpath paving with power tools for holes 0.4 m in diameter whose centers are 0.5 m from the cable line on an old drawing. The edge of each hole is only 0.5−0.4/2=0.30.5 - 0.4/2 = 0.3 m from that line, closer than the 500 mm advised by HSE, even though an old drawing can be off and the cable can be shallower than 450 mm. The digging is postponed until the contractor locates the cable with a signal transmitter, exposes it by hand digging, and holds a work permit; a hum detector in the daytime, when the garden lights are off, cannot be relied on.

    Stop conditions

    1. A guest or staff member feels a shock when touching a pole, bollard light, metal fence, or water near a luminaire: keep people away from the area and put up barriers, ask the designated person to disconnect the circuit at the panel, call the P3K (first aid) officer if anyone is injured, and hand the inspection to an authorized electrician.
    2. A cable is seen, scraped, or cut during digging, or the digging hits an object suspected to be a cable: stop digging, do not touch the cable or the tool, clear the area, report to the duty engineer, and leave it to an authorized electrician to isolate the circuit.
    3. The RCD of an outdoor lighting circuit trips repeatedly: do not bridge it, hold its lever, or replace it with a less sensitive RCD; leave the circuit off, put up safe temporary lighting on guest paths if needed, and hand the search for the cause to an authorized electrician.
    4. A luminaire, bollard light, or in-ground light contains water, has broken glass, or has exposed cables: do not open or touch its interior; put up barriers, report it, and have the circuit isolated by an authorized electrician.
    5. A pole is leaning, has been hit, is cracked or rusted through at the base, has missing anchor nuts, or has a cracked foundation: put up barriers to a distance equal to the pole height, divert vehicles and pedestrians, and hand the assessment to a structural engineer or the pole manufacturer.
    6. A pole access door, garden light junction box, or outdoor lighting panel is open, damaged, or flooded: do not open it further or touch its contents; close off the area and call an authorized electrician.
    7. The work would require climbing to a luminaire on a tall pole or trimming branches near a pole: postpone it until there is a work-at-height permit, suitable access equipment, and isolation of the circuit according to Chapter 76 and Chapter 10 · Safety.
    8. Lightning strikes near the grounds and many luminaires, photocells, or drivers fail at once: do not switch the circuits back on repeatedly; report to the chief engineer for inspection of the circuits and surge protection by an authorized electrician.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    An RCD that keeps tripping after rain is broken, so just replace it with a 100 mA one.

    Why is it wrong?

    That RCD is most likely working correctly because there is leakage current from water or damaged insulation. RCDs above 30 mA provide very limited protection against electric shock, and the cause is found by measurement by an authorized electrician.

    Common misconception

    The cable detector did not beep, so there is no cable there.

    Why is it wrong?

    A hum detector does not respond to cables without current, such as garden light cables in the daytime, and most cables have no surface marker. A cable is positively located only when it has been safely exposed.

    Common misconception

    The brighter, the safer.

    Why is it wrong?

    Floodlights that are too bright cause glare and light entering guest rooms, and the dark areas between them become harder to see. What is wanted is uniformity and well-aimed luminaires.

    Common misconception

    A high-IP light will never let in water.

    Why is it wrong?

    An IP code applies to the enclosure as tested. Cracked glass, hardened gaskets, wrong glands, and condensation from a breathing luminaire still let water in.

    Common misconception

    A pole that is still standing is still strong.

    Why is it wrong?

    Rust at the base and foundation cracks cannot be seen from a distance, and a pole that has just been hit can be damaged inside. Changes in lean and damage at the base are assessed by an expert.

    Chapter 33 on lighting installations and Chapter 105 on building lighting cover the photometric quantities used to read outdoor measurements. Chapter 18 and Chapter 22 on RCD testing and selection protect metal poles and bollard lights, Chapter 30 on installing wiring systems explains laying underground cables, and Chapter 35 on surges and lightning explains damage to drivers and photocells after storms.

    Exercises and worked solutions

    The figures in the exercises are for practice.

    Try to answer first, then open the worked solution.

    1. Five measuring points on a footpath read 8, 4, 16, 2, and 10 lux. What are the average and the maximum to minimum uniformity?

      Check my answer
      See the worked solution

      The average is (8+4+16+2+10)/5=40/5=8(8 + 4 + 16 + 2 + 10)/5 = 40/5 = 8 lux, and the uniformity is 16/2=816/2 = 8. That uniformity is far from 20 to 1, but the 2 lux point is still checked because people coming from the 16 lux point have difficulty seeing there.

    2. A 2.5 mm² garden light cable 120 m long carries 2.0 A with the load assumed at the end. What is the voltage drop in volts and as a percentage of 230 V?

      Check my answer
      See the worked solution

      ΔU=2×0.0175×120×2.0/2.5=3.36\Delta U = 2 \times 0.0175 \times 120 \times 2.0/2.5 = 3.36 V, which is 3.36/230×100=1.463.36/230 \times 100 = 1.46 percent. This figure is an upper bound because the load is assumed at the end, and the applicable voltage drop limit is read in Chapter 28.

    3. A security officer suggests temporarily bridging the garden lighting RCD that trips every rainy night so that the guest path is not dark. What is the technician’s answer?

      Check my answer
      See the worked solution

      Bridging the RCD removes the only additional protection in a wet place, while the trip shows that there is real leakage current. The technician refuses, puts up safe temporary lighting if needed, and hands the search for the cause to an authorized electrician.

    4. The car park lights stay on all day for three days after a long power outage. What are two possible causes, and what does the technician do?

      Check my answer
      See the worked solution

      The timer may have lost its time because its backup power ran out, or the photocell may be faulty or covered so that it does not read daylight. The technician records the on and off times and the condition of the photocell from the outside, then asks an authorized electrician to inspect and reset that connected equipment.

    5. One 30 mA RCD protects LED luminaires that each leak 0.6 mA. How many luminaires at most under the 30 percent recommendation?

      Check my answer
      See the worked solution

      The limit is 0.30×30=90.30 \times 30 = 9 mA, so at most 9/0.6=159/0.6 = 15 luminaires per RCD. The other luminaires are moved to a circuit with its own RCD, and the division is designed by an authorized electrician from manufacturer data or measurements.

    6. A tent contractor will drive steel stakes into a garden crossed by lighting cables. What does the technician ask for before the work starts?

      Check my answer
      See the worked solution

      Steel stakes driven into the ground can penetrate a live cable and cause an arc that burns. The technician asks for the cable route drawing to be checked, the cables to be located and marked by a competent person, and the work to be done under a work permit that keeps the stakes away from the cable route.

    References

    External sources

    • Peraturan Menteri Ketenagakerjaan Nomor 5 Tahun 2018 tentang Keselamatan dan Kesehatan Kerja Lingkungan Kerjajdih.kemnaker.go.id
    • UFC 3-530-01 Interior and Exterior Lighting Systems, 09 February 2023, Change 1, 15 December 2023wbdg.org
    • Avoiding danger from underground services (HSG47, Third edition)hse.gov.uk
    • Frequently asked questions (FAQs)hse.gov.uk
    • Peraturan Menteri Ketenagakerjaan Nomor 12 Tahun 2015 tentang Keselamatan dan Kesehatan Kerja Listrik di Tempat Kerjajdih.kemnaker.go.id

    Revision history

    DateVersionChange
    November 15, 20261First published

    How to cite

    Kurnia (2026). Outdoor lighting on hotel grounds: street lights and garden lights, poles and foundations, underground cables, grounding and RCDs, timers and photocells, IP protection ratings, and maintenance. ARSTEMA Academy. Revised November 15, 2026. arstema.com/en/academy/konsep/penerangan-luar-kawasan-hotel-lampu-jalan-dan-lampu-taman-tiang-dan-fondasi-kabel-tanah-pembumian-dan-rcd-pengatur-waktu-dan-fotosel-tingkat-proteksi-ip-serta-perawatan

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated
    1

    Five measuring points on a footpath read 8, 4, 16, 2, and 10 lux. What are the average and the maximum to minimum uniformity?

    2

    A 2.5 mm² garden light cable 120 m long carries 2.0 A with the load assumed at the end. What is the voltage drop in volts and as a percentage of 230 V?

    3

    A security officer suggests temporarily bridging the garden lighting RCD that trips every rainy night so that the guest path is not dark. What is the technician’s answer?

    Self-assessment progress0%

    Nearby chapters