Skip to content

Search ARSTEMA

Type a chapter, term, symptom, or tool.

    Buildings & Facilities · Chapter 35Applied

    By Kurnia · Published November 13, 2026 · Version 1 · 20 min read

    Roofs and waterproofing

    roof types and coverings, gutters and rainwater downpipes, membranes and joints, finding the source of a leak, temporary repairs, and safe work on roofs

    Water drips from the ceiling of a hotel laundry ironing room next to a machine panel, and a technician is getting ready to climb onto the fiber cement roof to check a blocked box gutter. This chapter covers roofs and waterproofing from the building technician’s side: roof types and their coverings, slope, gutters and rainwater downpipes, ponding, membranes and flashings, how to trace the source of a leak from inside the building, safe temporary repairs, and the limits of work on fragile roofs, at roof edges, and in rain or lightning. British roof safety guidance, the roofing criteria of the United States Department of Defense, and American building preservation guidance are used as data from their countries of origin, while Permenaker 9/2016 is the basis for work at height in Indonesia. Walking on fragile roofs, working at roof edges without fall protection, and repairs to roof coverings are set out as work for competent persons with a fall protection system and a work permit.

    High-risk material

    This material involves real hazards. A concept explanation doesn’t replace site procedures, competency, energy isolation, the latest SDS, or a work permit.

    Section you’re reading: Chapter opening

    On a night of heavy rain, water drips from the ceiling of the ironing room in a hotel’s laundry building, about one meter from the control panel of the flatwork ironer. The building has one story and a roof of corrugated fiber cement sheets with a row of translucent sheets, and its rainwater runs into a box gutter between two roof spans. The next morning a technician leans a ladder against the wall to take a quick look at the gutter, which is suspected of being blocked by lint from the dryer exhaust duct. The supervisor stops the job: fiber cement sheets and translucent sheets are not designed to carry a person’s weight, and the 30 cm wide box gutter between them is not a walkway.

    The technician then maps the stain from a reference point inside the building, photographs the gutter with a pole-mounted camera from the platform of a lifting machine operated by a licensed person, and hands the gutter cleaning to a roofing contractor who installs protection over the fragile sheets. Much about a roof can be learned from below; work on top of a roof needs fall protection that has been planned first.

    Scope

    This chapter covers roofs and waterproofing from the building technician’s side: roof types and their coverings, the path of water to gutters and rainwater downpipes, membranes and joints that tend to leak, tracing the source of a leak, temporary repairs from a safe place, and the limits of work on roofs. It explains how to recognize the hazards and how to divide the work; it is not a work instruction for roofs, and it contains no steps for walking on a fragile roof or working at a roof edge without fall protection.

    Work at height, ladders, scaffolds, fall arrest, and falling objects are in Chapter 10 · Safety on work at height and are not repeated; this chapter only adds the limits specific to fragile roofs and roof edges. Rainwater flow is in Chapter 10 on drainage hydraulics, rooftop tanks in Chapter 5 on building water supply, solar modules on roofs in Chapter 90 · Electrical & Control on DC-side safety of rooftop PV and Chapter 93 · Electrical & Control on maintaining solar module arrays, lightning protection in Chapter 35 · Electrical & Control, loads and load paths in Chapter 1, and mold in Chapter 9 · Biology & Microbiology.

    As of November 2026, JDIH Kemnaker records Permenaker 9/2016 (Minister of Manpower Regulation) on K3 (occupational safety and health) for work at height as in force. The status and content of Permen PU 24/PRT/M/2008 on guidelines for the maintenance and upkeep of buildings cannot yet be confirmed as of November 2026; check with JDIH PUPR before using it for schedules or audits. Work outside the building technician’s authority: standing or walking on roof coverings, working near an unguarded roof edge or opening, installing edge protection, anchor points, or safety nets, repairing roof coverings and membranes, using torches or hot asphalt, judging whether a roof can carry ponded water, and working around solar modules. That work belongs to roofing contractors or other competent persons with a fall protection system and a work permit, and judging strength belongs to a structural engineer.

    Roof types and coverings

    A steep-slope roof is a roof that sheds water by its slope; its covering consists of overlapping units, such as tiles, shingles, or corrugated sheets, so water runs from the upper unit to the lower one before it can get in. A low-slope roof is an almost flat roof that relies on a membrane, a continuous waterproof layer. The roofing criteria of the United States Department of Defense use a limit of 3:12 (14 degrees): membranes are installed on slopes up to that limit, water-shedding coverings above it, and new membrane roofs are designed no flatter than 1/2:12.

    Slope is written as an angle, a percentage, or a ratio:

    θ=arctan⁡(hl),s=hl×100 %\theta = \arctan\left(\frac{h}{l}\right), \qquad s = \frac{h}{l} \times 100\,\%

    where θ\theta is the roof angle from the horizontal (degrees), hh the vertical rise (m), ll the horizontal run (m), and ss the slope in percent; “3:12” means a rise of 3 units for every 12 horizontal units. The formula assumes a flat roof plane; a sagging area has a different local slope and becomes the place where water ponds.

    Building roof coverings are generally clay or concrete tiles, profiled metal sheets, fiber cement sheets, translucent sheets for daylighting, or concrete slabs covered with a bitumen membrane, a synthetic sheet membrane, or a liquid-applied coating. Tiles leak when units slip, crack, or overlap too little; metal sheets leak at screw holes, brittle rubber washers, and corroded laps; membranes leak at sheet seams, edges, and where pipes or equipment supports pass through them. A good roof stays dry inside and out, and condensation on the underside of the covering indicates inadequate ventilation.

    Gutters, rainwater downpipes, and ponding

    A gutter is a channel that collects water from a roof edge or from the junction of two roof planes and carries it to a rainwater downpipe. A box gutter is a gutter located inside the roof boundary, between two spans or behind a parapet, so that its overflow goes straight into the building.

    Gutters and downpipes need periodic cleaning; water held back by debris backs up and seeps under the covering units and damages fasteners, sheathing, and roof framing, while a blocked downpipe inside the building can send water back into the walls. The American roofing criteria list design measures that reduce blockages: oversized downpipes, fewer bends, strainers at the pipe inlet except where there are many leaves, and clean-outs at the foot of the pipe.

    Ponding is water held on a low-slope roof after the rain stops because the slope is too small, the roof sags, or the drain is blocked. Its weight per unit area is

    w=ρ g dw = \rho \, g \, d

    where ww is the load per area (N/m²), ρ\rho the density of water (about 1,000 kg/m³), g=9.81g = 9.81 m/s², and dd the depth of ponding (m); every millimeter of water is about 1 kg per square meter. The formula only calculates the weight of the water. Whether the roof can carry it is a judgment for a structural engineer under Chapter 1 on loads and load paths, all the more because a sagging roof holds more water. For a roof that keeps leaking and is awaiting replacement, the American roofing criteria ask for the drainage to be checked and debris removed to prevent excessive ponding and possible roof collapse.

    Membranes, flashings, and material junctions

    A roof seldom leaks in the middle of an intact plane. Water gets in where the roof plane is interrupted: roof edges, walls rising from the roof, equipment supports, vent pipes, drains, and translucent sheets. Flashing is a metal sheet, membrane, or flexible material that closes the gap at such a junction and directs water back onto the roof surface. Its failure is usually a major cause of roof deterioration, through poor workmanship, thermal stress, or deterioration of the sheet metal and its fasteners. The American roofing criteria state that most leaks originate at flashings and call for detailed inspection at translucent sheets, edges, walls, penetrations, equipment supports, and drains.

    On a membrane roof, the sheet laps must be fully bonded, and the membrane must be protected from mechanical damage such as foot traffic or falling branches. Sealant around penetrations ages faster than the membrane, so it is inspected more often. Material junctions are also a source of damage: some roof coverings and flashing materials are not compatible with each other, and fasteners must be of a compatible material or coated. Plain steel screws in wet aluminum sheet form a galvanic cell as in Chapter 19 · Chemistry on electrochemical corrosion, so replacement materials follow what the roofing contractor specifies.

    Finding the source of a leak

    The drip point on a ceiling is seldom directly below the hole. Water runs along the sheathing, purlins, pipes, or cables before it drips, and it can travel long distances inside walls; a ceiling stain can also come from a leaking pipe, a blocked fan coil unit drain pan, or a window sill with the wrong slope. The American roofing criteria warn that seepage reported as a roof leak can come from walls, windows, or mechanical units, so investigation comes before repair.

    The search moves from inside to outside and does not begin by climbing onto the roof:

    1. Map the symptoms. Measure the position of the stain from a reference point that also appears on the roof plan, such as an outside wall or a column, so the damage inside can be matched to a location on the roof.
    2. Record when the leak happens. A leak during wind-driven rain, when the gutter overflows, or in dry weather gives different clues; a leak in dry weather points to a water pipe or a condensate pan.
    3. Read the direction of flow. The source on the roof is usually at the same point as the drip point or higher along the slope, because water does not run uphill on a sloping plane (Example 3).
    4. List the candidate sources in that area, such as flashings, translucent sheets, penetrations, box gutters, and drains, before anything is opened up.
    5. Observe in the rain from a safe place, that is, from the ground, a window of a taller building, or a guarded roof terrace; watching a building in the rain often answers many questions about the water’s path.
    6. Keep a sequential record of scaled photographs, dates, and rainfall, so the result of a repair can be judged.

    Infrared thermography and other nondestructive inspections help find wet areas of a roof, but they do not replace visual inspection and are confirmed with a roof core sample by trained people. The American roofing criteria require every roof to be inspected at least once a year and note the recommendation of the American roofing contractors’ association to inspect twice a year and after major storms.

    Temporary repairs

    Temporary repairs limit the damage until the cause of the leak is properly repaired, and most of the work is done from inside the building. The water is caught, the ceiling and the equipment below are protected with plastic sheeting, the wet floor is marked, and unsafe rooms are cleared. When water reaches lights, outlets, or a panel, the circuit is isolated by an authorized electrician as in Chapter 76 · Electrical & Control on safe electrical work and LOTO. A ceiling that bulges with water is treated as something that can collapse.

    Repairs on top of the roof, even temporary ones, are roofing work. The American roof preservation guidance asks for temporary patching methods to be chosen carefully so they do not damage sound roofing material, and mentions temporary covering with plywood and building paper until the roof is repaired or replaced. A waterproof coating applied carelessly can trap water; on one building, such a coating held water from a leaking roof until the parapet failed.

    Many membrane repairs use hot asphalt, torches, and solvent-based materials, which require trained people and, where there is an open flame, a hot work permit. A roof still under warranty is repaired according to the warranty terms, and the warrantor is contacted first; a roof that keeps leaking despite repeated repairs is scheduled for replacement.

    Fragile roofs and roof edges

    The roof work guidance of HSE, the British occupational safety body, records that roof work accounts for a quarter of deaths in the British construction industry, that falls through fragile materials such as translucent sheets and asbestos cement sheets are the largest single cause, and that many victims are maintenance workers. The HSE roof work page gives a slightly different figure, almost one in five construction deaths, and adds that work on roofs remains highly dangerous even if it takes only a few minutes.

    A fragile roof is a roof assembly that cannot carry the weight of a person and the materials they carry. HSE asks for all roofs to be treated as fragile until a competent person has confirmed otherwise, because even roofs designed as non-fragile become fragile with time. Likely fragile items include old translucent sheets, non-reinforced fiber cement sheets, corroded metal sheets, glass including wired glass, rotted boards, and some tiles; old translucent sheets can be covered by paint or dirt until their color matches the surrounding roof.

    Two habits often end in a fall. Walking along the line of bolts over the purlins is thought to be safe, yet for translucent and fiber cement sheets the weakest point lies within 150 mm of the purlin line, because the purlin becomes an edge that tears the sheet. A sheet that looks solid can carry a distributed load but break without warning under a heel or a person who stumbles. For work on a fragile roof, the HSE order is to work from below the roof using a platform, then from the basket of a mobile elevating work platform without standing on the roof, and where access onto the roof cannot be avoided, to install edge protection, staging, and nets or a harness system designed for that purpose.

    A roof edge is any side from which a person can fall to a lower level, including openings in the roof plane. In Britain, temporary guardrails under the work at height regulations consist at a minimum of a main guardrail 950 mm above the edge, a toe board of 150 mm, and an intermediate rail that leaves an unprotected gap of no more than 470 mm; a sufficiently strong parapet at least 950 mm high serves as permanent edge protection. On a large roof where only part is worked on, HSE accepts a continuous physical barrier generally at least 2 m from the edge or fragile areas, with no unprotected openings or fragile material inside the safe area, and only with skilled workers and strict supervision. These figures are British data; in Indonesia, edge protection is designed by competent persons under the regulations in force.

    Permenaker 9/2016 defines work at height as work at a place with a difference in height and a potential fall that could injure or kill the worker or other people. The regulation requires work at height to be carried out only when it cannot be done at ground level, requires a work-at-height permit system when the fall risk cannot be eliminated, and requires the work area to be divided into danger, caution, and safe zones. The order for the technician: inspect from below first, and go onto a roof only with a permit, competent persons, and fall protection as in Chapter 10 · Safety.

    Inspecting from below, rain, wind, and lightning

    HSE asks for roof inspections to avoid work at height when only looking is needed, for example with a pole-mounted camera or a drone where permitted, with the operator staying on the ground. When going up cannot be avoided, the inspection is made from a safe place, such as binoculars from a neighboring building, mobile access equipment, or a scaffold tower, and an industrial roof whose condition is in doubt is not walked on for a survey. In a hotel or hospital, the roof space is often the best place for an inspection, provided its walkways are actually designed to be walked on.

    Rain makes footing slippery, so the roof is checked again before work starts, and a sudden gust of wind can make a person lose balance. The American roofing criteria also require roof repair work to be done by at least two people.

    The lightning guidance of the United States National Park Service states that a person who hears thunder is close enough to be struck, that there is no safe place outdoors during a thunderstorm, and that activity resumes at least 30 minutes after the last lightning is seen or the last thunder is heard, even if the rain has stopped. Lightning conductors on the roof are covered in Chapter 35 · Electrical & Control on lightning protection and are not inspected in thundery weather.

    Worked example

    The numbers in the examples below are practice numbers, unless their origin is stated.

    Example 1: reading roof slope. The 3:12 limit gives θ=arctan⁡(3/12)=14.0∘\theta = \arctan(3/12) = 14.0^\circ and s=3/12×100=25s = 3/12 \times 100 = 25 percent; the minimum slope of 1/2:12 gives θ=arctan⁡(0.5/12)=2.4∘\theta = \arctan(0.5/12) = 2.4^\circ and s=4.2s = 4.2 percent. A tile roof at 30° has s=tan⁡30∘×100=57.7s = \tan 30^\circ \times 100 = 57.7 percent, far above that limit, while a concrete slab at 1 percent has an angle of only arctan⁡(0.01)=0.57∘\arctan(0.01) = 0.57^\circ and depends entirely on its membrane.

    Example 2: weight of ponded water on a roof slab. A 12 m by 10 m laundry roof slab holds an average of 50 mm of ponded water. The water volume is 12×10×0.05=612 \times 10 \times 0.05 = 6 m³, about 6,000 kg, and its weight is 6,000×9.81=58,8606{,}000 \times 9.81 = 58{,}860 N, or about 58.9 kN. Per square meter, w=1,000×9.81×0.05=490.5w = 1{,}000 \times 9.81 \times 0.05 = 490.5 N/m², about 50 kg/m². This figure is reported as the weight of the water; nobody goes onto the ponded slab, and the strength of the slab is judged by a structural engineer.

    Example 3: drip point and direction of flow. The stain on the ironing room ceiling is 7.0 m from the west wall and 3.0 m from the north wall, and the roof slopes down to the north toward the box gutter. On a plan using the same reference, the dryer exhaust outlet is at (7.5, 2.0) m and the translucent sheet at (8.5, 4.5) m. The horizontal distance to the exhaust outlet is 0.52+1.02=1.1\sqrt{0.5^2 + 1.0^2} = 1.1 m and to the translucent sheet 1.52+1.52=2.1\sqrt{1.5^2 + 1.5^2} = 2.1 m. The exhaust outlet is closer, but it lies 1.0 m downslope of the drip point, so water entering there flows away. The translucent sheet is 1.5 m upslope, so its flashing becomes the first candidate to inspect with the camera.

    Example 4: work area with a 2 m barrier. On a 24 m by 16 m roof slab, a barrier 2 m from every edge according to the British guidance leaves (24−4)×(16−4)=240(24 - 4) \times (16 - 4) = 240 m² of 24×16=38424 \times 16 = 384 m², that is 240/384=62.5240/384 = 62.5 percent. A cooling unit standing 1.2 m from the edge is outside that area, so its maintenance needs edge protection installed by competent persons.

    Example 5: edge protection under the British minimum standard. A parapet of 0.90 m is lower than 0.95 m, so under the British standard it does not yet count as permanent edge protection. A temporary guardrail with a main rail at 1.00 m, an intermediate rail at 0.55 m, and a toe board of 0.15 m has gaps of 1.00−0.55=0.451.00 - 0.55 = 0.45 m and 0.55−0.15=0.400.55 - 0.15 = 0.40 m, both no more than 0.47 m. If the intermediate rail is fitted at 0.50 m, the upper gap is 1.00−0.50=0.501.00 - 0.50 = 0.50 m and exceeds 0.47 m. The design of the guardrail still belongs to competent persons.

    Example 6: thunder and the time to return. Thunder is heard 8 seconds after the lightning. With a speed of sound of about 343 m/s, the strike is about 343×8=2,744343 \times 8 = 2{,}744 m away, roughly 2.7 km, and thunder that can be heard is reason enough to go inside the building. If the last thunder is heard at 15:20, work on the roof terrace resumes at 15:50 at the earliest.

    Stop conditions

    1. The work or inspection would require someone to stand or walk on roof sheets, translucent sheets, a box gutter between sheets, or a roof that a competent person has not confirmed as non-fragile: do not go up; inspect from below or from access equipment, and hand the work to a roofing contractor with a fall protection system and a work-at-height permit.
    2. The work point is near a roof edge, opening, or hole with no edge protection or barrier: stop the work; edge protection or a fall protection system is installed by competent persons, and the work supervisor decides when work resumes.
    3. Thunder is heard, lightning is seen, rain has made the surface slippery, or the wind is strong enough to unsettle people or materials: come down and go inside the building; work resumes at least 30 minutes after the last thunder and after the supervisor has checked the roof again.
    4. Water is ponding on the roof, a ceiling sags or bulges with water, or cracking sounds come from the roof: clear the room below, do not go onto the roof and do not pierce the ceiling from beneath the ponded water, then report to the building manager, who calls a structural engineer.
    5. Leaking water reaches a panel, light, outlet, or electrical equipment: keep people away and ask an authorized electrician to isolate the circuit before anyone approaches.
    6. The repair would require a torch, hot asphalt, solvent-based materials, or opening up the roof covering, or the roof is still under warranty: postpone it; the work is handed to a roofing contractor with a hot work permit where needed, and the warrantor is contacted first.
    7. The leak is around solar modules, cables, or their supports: do not touch; hand it to an authorized PV technician under Chapter 90 · Electrical & Control on DC-side safety of rooftop PV.
    8. Old fiber cement sheets that may contain asbestos would have to be cleaned, drilled, cut, or removed: stop; the work is handed to a contractor authorized to handle asbestos.

    Common misinterpretations

    Guess what’s wrong first, then open the explanation.

    Common misconception

    A new roof sheet is surely strong enough to step on.

    Why is it wrong?

    All roofs are treated as fragile until a competent person has confirmed otherwise. A sheet that looks solid can break under a heel, and even a roof designed as non-fragile becomes fragile with time.

    Common misconception

    Walking along the line of purlin bolts is safe.

    Why is it wrong?

    For translucent and fiber cement sheets, the weakest point lies within 150 mm of the purlin line. One wrong step is enough to fall through the roof.

    Common misconception

    The hole is surely right above the ceiling stain.

    Why is it wrong?

    Water runs along sheathing, framing, and pipes before it drips, and a stain can come from a pipe, a condensate pan, or a window. The source is traced with a map from a reference point and the direction of flow, as in Example 3.

    Common misconception

    An extra waterproof coating always helps.

    Why is it wrong?

    A coating that closes the water’s way out can trap water inside a wall or roof. Repairs on top of the roof remain work for a roofing contractor.

    Common misconception

    The rain has stopped, so the lightning has passed.

    Why is it wrong?

    The danger of a strike remains after a storm has passed. Work on a roof resumes at least 30 minutes after the last thunder.

    Chapter 10 · Safety on work at height provides the basis for access, fall arrest, and rescue plans. Chapter 10 on drainage hydraulics calculates rainwater flow, Chapter 1 on loads and load paths explains why the weight of ponded water is handed to a structural engineer, and Chapter 19 · Chemistry on electrochemical corrosion explains the corrosion of fasteners. Water that enters through the roof often shows up as stains and cracked plaster, covered in Chapter 36 on cracks in walls and concrete, and protective surface coatings are covered in Chapter 37 on building paints and coatings.

    Exercises and worked solutions

    The numbers in the exercises are for practice.

    Try to answer first, then open the worked solution.

    1. A concrete roof slab is designed with a slope of 1:50. What is its slope in percent and in degrees, and what type of roof is it under the 3:12 limit?

      Check my answer
      See the worked solution

      The slope is 1/50×100=21/50 \times 100 = 2 percent and arctan⁡(0.02)=1.15∘\arctan(0.02) = 1.15^\circ, far below the 3:12 or 14 degree limit. The slab is a low-slope roof that depends on its membrane, so the membrane seams and the drains are its main inspection points.

    2. An 8 m by 15 m roof slab holds an average of 40 mm of ponded water. What are the mass of the water and the load per square meter, and who judges whether the roof can carry it?

      Check my answer
      See the worked solution

      The water volume is 8×15×0.04=4.88 \times 15 \times 0.04 = 4.8 m³, about 4,800 kg, and w=1,000×9.81×0.04=392.4w = 1{,}000 \times 9.81 \times 0.04 = 392.4 N/m², about 0.39 kN/m². That figure is only the weight of the water; whether the roof can carry it is judged by a structural engineer, while the technician reports it and asks for the drain to be cleared from safe access.

    3. A coworker says the fiber cement sheets on the warehouse roof were installed only two years ago, so they are safe to walk on to clean the box gutter. What is the technician’s answer?

      Check my answer
      See the worked solution

      The age of the sheets does not prove the roof is non-fragile, because all roofs are treated as fragile until a competent person has confirmed otherwise and fiber cement sheets can break without warning under a heel. A box gutter between fragile sheets is cleaned by a roofing contractor with protection over the sheets and a work-at-height permit.

    4. A physical barrier is placed 2 m from every edge of an 18 m by 10 m roof slab. What is the area inside the barrier, and what is required inside that area?

      Check my answer
      See the worked solution

      The area is (18−4)×(10−4)=14×6=84(18 - 4) \times (10 - 4) = 14 \times 6 = 84 m². There must be no unprotected openings or fragile material inside that area, so translucent sheets or openings inside it are given robust covers or barriers, and the method is only used with skilled workers and strict supervision.

    5. A new stain appears on a hotel room ceiling on a day without rain, directly below the fan coil unit above the ceiling. Is the roof the first candidate?

      Check my answer
      See the worked solution

      No. A stain on a dry day below a fan coil unit is more likely to come from a blocked condensate pan or a chilled water pipe, because roof leaks appear after rain. The technician checks the pan and the condensate drain from the ceiling space first and records when the stain appeared.

    6. A technician is inspecting a drain on a guarded roof terrace when thunder is heard at 16:45. What does the technician do, and when can work resume at the earliest if there is no more thunder?

      Check my answer
      See the worked solution

      The technician stops the inspection and goes inside the building, because thunder that can be heard means the strike is close enough to hit and there is no safe place outdoors. Work resumes at 17:15 at the earliest, which is 30 minutes after the last thunder, after the terrace has been checked again.

    References

    External sources

    • Health and safety in roof workhse.gov.uk
    • Roof workhse.gov.uk
    • UFC 3-110-03 Roofing, with Change 5wbdg.org
    • Preservation Brief 4: Roofing for Historic Buildingsnps.gov
    • Preservation Brief 39: Holding the Line: Controlling Unwanted Moisture in Historic Buildingsnps.gov
    • When Thunder Roars, Go Indoorsnps.gov
    • Peraturan Menteri Ketenagakerjaan Nomor 9 Tahun 2016 tentang Keselamatan Dan Kesehatan Kerja Dalam Pekerjaan Ketinggianjdih.kemnaker.go.id

    Revision history

    DateVersionChange
    November 13, 20261First published

    How to cite

    Kurnia (2026). Roofs and waterproofing: roof types and coverings, gutters and rainwater downpipes, membranes and joints, finding the source of a leak, temporary repairs, and safe work on roofs. ARSTEMA Academy. Revised November 13, 2026. arstema.com/en/academy/konsep/atap-dan-kedap-air-jenis-atap-dan-penutupnya-talang-dan-pipa-air-hujan-membran-dan-sambungan-mencari-sumber-bocor-perbaikan-sementara-serta-kerja-aman-di-atap

    Self-check · 3 questions

    Check your understanding before moving on

    Write your answer in your own words, then compare it with the worked solution from this chapter’s exercises. The system doesn’t judge open answers as right or wrong; you decide which parts you’ve understood.

    0/3rated

    Safety limits still apply. This quiz tests reasoning; it doesn’t authorize mixing, adjusting, dismantling, live measurement, or field action.

    1

    A concrete roof slab is designed with a slope of 1:50. What is its slope in percent and in degrees, and what type of roof is it under the 3:12 limit?

    2

    An 8 m by 15 m roof slab holds an average of 40 mm of ponded water. What are the mass of the water and the load per square meter, and who judges whether the roof can carry it?

    3

    A coworker says the fiber cement sheets on the warehouse roof were installed only two years ago, so they are safe to walk on to clean the box gutter. What is the technician’s answer?

    Self-assessment progress0%

    Nearby chapters